Preparation and field emission properties of carbon nanotubes cold cathode using melting Ag nano-particles as binder

A new preparation process for carbon nanotubes (CNTs) cold cathode was studied through the replacement of traditional organic or inorganic binder with Ag nano-particles. This method has the advantages of low preparation temperature and fine electrical contact between CNTs paste and substrate. A mixture paste of CNTs, Ag nano-particles and other organic solvents was spreaded on Si substrate. By melting and connecting of Ag nano-particles after sintered 30 min at 250 °C, a flat CNTs films with good field emission properties was obtained. The measurements reveal that the turn on electric field and the threshold electric field of as-prepared CNTs cathode are 2.1 and 3.9 V/μm respectively and the field emission current density is up to 41 mA/cm² at an applied electric field of 4.7 V/μm.     

Field emission properties of electrophoretic deposition carbon nanotubes film

The field emission properties of electrophoretic deposition(EPD) carbon nanotubes (CNTs) film have been improved by depositing CNTs onto the titanium (Ti)-coated Si substrate, followed by vacuum annealing at 900 °C for 2 h, and the enhanced emission mechanism has been studied using X-ray diffraction (XRD), scanning electron microscope (SEM) and Raman spectroscopy. Field emission measurements showed that the threshold electric field was decreased and the emission current stability was improved compared to that of EPD CNTs film on bare Si substrate. XRD and Raman spectroscopy investigations revealed that vacuum annealing treatment not only decreased the structural defects of CNTs but made a titanium carbide interfacial layer formed between CNTs and substrate. The field emission enhancement could be attributed to the improved graphitization of CNTs and the improved contact properties between CNTs and substrate including electrical conductivity and adhesive strength due to the formed conductive titanium carbide.     

Enhanced field emission from ZnO nanopencils by using pyramidal Si(1 0 0) substrates

Zinc oxide nanopencil arrays were synthesized on pyramidal Si(1 0 0) substrates via a simple thermal evaporation method. Their field emission properties have been investigated: the turn-on electric field (at the current density of 10 μA/cm²) was about 3.8 V/μm, and the threshold electric field (at the current density of 1 mA/cm²) was 5.8 V/μm. Compared with similar structures grown on flat Si substrates, which were made as references, the pyramidal Si-based ZnO nanopencil arrays appeared to be superior in field emission performance, thus the importance of the non-flat substrates has been accentuated. The pyramidal Si substrates could not only suppress the field screening effect but also improve the field enhancement effect during the field emission process. These findings indicated that using non-flat substrates is an efficient strategy to improve the field emission properties.     

Efficient field emission from coiled carbon nano/microfiber on copper substrate by dc-PECVD

Crystalline coiled carbon nano/micro fibers in thin film form have been synthesized via direct current plasma enhanced chemical vapor deposition (PECVD) on copper substrates with acetylene as a carbon precursor at 10 mbar pressure and 750 °C substrate temperature. The as-prepared samples were characterized by X-ray diffraction (XRD) analysis, scanning electron microscopy (SEM) and high resolution transmission electron microscopy (HRTEM). XRD pattern as well as selected area electron diffraction (SAED) pattern showed that the samples were crystalline in nature. SEM and HRTEM studies showed that as synthesized coiled carbon fibers are having average diameter ∼100 nm and are several micrometers in length. The as-prepared samples showed moderately good electron field emission properties with a turn-on field as low as 1.96 V/μm for an inter-electrode distance 220 μm. The variation of field emission properties with inter-electrode distance has been studied in detail. The field emission properties of the coiled carbon fibrous thin films are compared with that of crystalline multiwalled carbon nanotubes and other carbon nanostructures.     

Effects of microwave plasma treatment on the field emission properties of printed carbon nanotubes/Ag nano-particles films

The effects of Ar microwave plasma treatment on field emission properties of the printed carbon nanotubes (CNTs) cathode films using Ag nano-particles as binder were investigated. The field emission J-E characteristics were measured at varied plasma treatment time. Significant improvement in emission current density, emission stability and uniformity were achieved for the Ar treated CNTs films, even though the plasma treatment increased the turn on electric field slightly. High-resolution transmission electron microscopy (HRTEM) and Raman spectroscopy revealed the microstructural changes of CNTs after the plasma treatment. The improved field emission properties of CNTs film can be attributed to the generation of a high density of structural defects after treatment, which increased greatly the possible emission active sites. Besides, the formation of the sharpened and open-ended CNTs tips is all helpful for improving the field emission properties of the treated CNTs.     

Tunnelling Radiation of Charged and Magnetized Massive Particles from BTZ Black Holes

We investigate the tunnelling radiation of charged and magnetized massive particles from a Banados-Teitelboim- Zanelli （BTZ） black hole by extending the Parikh-Wilczek tunnelling framework. In order to calculate the emission rate, we reconstruct the electromagnetic field tensor and the Lagrangia~n of the field corresponding to the source with electric and magnetic charges, and treat the charges as an equivalent electric charge for simplicity in the later calculation. The result supports Parikh-Wilczek＇s conclusion, that is, the Hawking thermal radiation actually deviates from perfect thermality and agrees with an underlying unitary theory.     

Characterization and field emission characteristics of carbon nanotubes modified by titanium carbide

Carbon nanotubes (CNTs) were modified by depositing a thin layer of titanium film on the surface using magnetron sputtering method, followed by vacuum annealing at 900 °C for 2 h. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) confirmed that the as-deposited thin titanium film reacted with carbon atoms to form titanium carbide after annealing. The experiment results show that the thickness of sputter-deposited titanium film has significant effect on the field emission J-E characteristic of modified CNTs film. The titanium carbide-modified CNTs film obtained by controlling the titanium sputtering time to 2 min showed an improved field emission characteristics with a significant reduction in the turn-on electric field and an obvious increase in the emission current density as well as an improvement in emission stability. The improvement of field emission characteristics achieved is attributed to the low work function and good resistance to ion bombardment of titanium carbide.     

Density functional theory study of the electronic and field emission properties of nitrogen- and boron-doped carbon nanocones

Using first-principles density functional theory, we have investigated the electronic and field emission properties of carbon nanocones (CNCs) doped with N or B with 60° disclination. Our findings are that the emission properties for the doped CNCs depend on the doping species, position, and concentration. Compared to pristine CNC, N-doped CNCs exhibit better field emission properties, in which as the doping concentration increases from 1.25% to 2.5% the maximum emission current at applied electric field of 0.3 V/Å increases from 0.94 μA (one N atom is doped at the position adjacent to the pentagon) to 2.90 μA (two N atoms are doped at pentagon). As for pristine CNC the emission current is only 0.21 μA. However, B-doping has no significant influence on the emission properties of CNCs. Our findings suggest that N-doped CNCs can be used as a candidate for cold-emission electron sources.     

Low-temperature photoluminescence of MBE-grown GaAs subject to an electric field

Low-temperature photoluminescence of GaAs has been investigated in MBE-grown Al _x Ga_1–x As-GaAs single heterojunctions subject to an electric field. No peak energy shift is observed in the emission lines due to free excitons and excitons bound to isolated centers when the electric field is applied. In contrast, the excitonic lines arising from the previously described defect-induced bound exciton (DIBX) transitions exhibit a prominent low-energy shift when the electric field is increased. We attribute these lines to excitons bound to acceptor pairs. The excitons bound to distant pairs have smaller binding energies than those bound to closer pairs. They are, therefore, easily dissociated in a weak electric field. The electrons and holes thus dissociated may again be trapped by closer pairs, which results in a low-energy shift of the overall spectrum. The photocurrent measured as a function of the electric field supports Dingle's rule for the valence bandedge discontinuity.     

Field electron emission from HfNxOy thin films deposited by direct current sputtering

HfN_xO_y thin films were deposited on Si substrates by direct current sputtering at room temperature. The samples were characterized by scanning electron microscopy (SEM), atomic force microscopy (AFM) and X-ray diffraction (XRD). SEM indicates that the film is composed of nanoparticles. AFM indicates that there are no sharp protrusions on the surface of the film. XRD pattern shows that the films are amorphous. The field electron emission properties of the film were also characterized. The turn-on electric field is about 14 V/μm at the current density of 10 μA/cm², and at the electric field of 24 V/μm, the current density is up to 1 mA/cm². The field electron emission mechanism of the HfN_xO_y thin film is also discussed.     

A comparative study of field-emission from different one dimensional carbon nanostructures synthesized via thermal CVD system

Different one dimensional (1D) carbon nanostructures, such as carbon nanonoodles (CNNs), carbon nanospikes (CNSs) and carbon nanotubes (CNTs) have been synthesized via thermal chemical vapour deposition (TCVD) technique. The different 1D morphologies were synthesized by varying the substrate material and the deposition conditions. The as-prepared samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscope (FESEM) and transmission electron microscope (TEM). FESEM and TEM images showed that the diameters of the CNNs and CNTs were ∼40 nm while the diameters of the CNSs were around 100 nm. Field emission studies of the as-prepared samples showed that CNSs to be a better field emitter than CNNs, whereas CNTs are the best among the three producing large emission current. The variation of field emission properties with inter-electrode distance has been studied in detail. Also the time dependent field emission studies of all the nanostructures have been carried out.     

Enhanced Field Emission from Vertical ZnO Nanoneedles on Micropyramids

Vertical ZnO nanoneedles with sharp tips are secondarily grown on tips of primarily grown ZnO micropyramids by a vapour transport process. The field emission （FE） properties exhibit a lower turn-on electric field and a higher field enhancement factor as compared with vertical ZnO microrods. This result indicates that ZnO nanoneedles have good optimum shapes for FE due to electron accumulation at sharp tips.     

The effect of hydrogen dilution on the field emission from hydrogenated amorphous carbon films

The microstructures and field emission characteristics of hydrogenated amorphous carbon films prepared by using different hydrogen dilution ratio were investigated. It was found that a very low threshold electric field emission could be achieved for samples with moderated hydrogen dilution ratio. However, the field emission characteristics became worse for samples with high hydrogen dilution ratio. The change of field emission can be attributed to the change of electronic structures due to the hydrogen dilution in addition to the increase of the hydrogen surface termination.     

Field-induced evaporation of carbon nanotubes

We report here an experimental observation of field emission from arrays of multiwall carbon nanotubes. Current densities in the range 10–30 mA/cm² with excellent long-term stability were recorded. A detailed study of the destruction of nanotubes at extreme operation conditions is performed. We established that field evaporation of nanotubes accompanies field emission from a cold cathode at electric fields higher than 2 V/?. Electron microscopy of the evaporation products reveals irregularly shaped carbon nanoparticles with a hollow core. The diameter of the particles is ∼20 nm. A mechanism of the process is proposed and discussed. Received: 6 October 2000 / Accepted: 28 April 2001 / Published online: 27 June 2001     

Shape of a liquid metal ion source

A model of the liquid-metal ion-source shape consisting of a jet-like protrusion on the end of a Taylor cone shape is shown to be consistent with a field evaporation mechanism of ion formation, fluid dynamic considerations, space charge effects and recent TEM observations. The diameter of the ion emitting area is found to be only a few tens of Å. Self-consistent numerical calculations of electric potential and particle trajectories predict emission characteristics which compare favorably with experimental results.On leave from Trinity Hall, Cambridge, UK     

Precision PAC measurements in Er2O3 and Ho2O3 single crystals and structure refinement

The structure of C-form Ho₂O₃ and Er₂O₃ single crystals and powder samples was investigated by the electric quadrupole hyperfine interaction of¹¹¹In(EC)¹¹¹Cd probe ions using the perturbed - angular correlation method (PAC). The resulting set of refined atomic coordinates is compared to X-ray data and used to calculate the orientations of the electric field gradients (EFG) which are reproduced by the PAC measurements in single crystals. The temperature dependence of the coordinates was measured for both substances.     

Estimation of built-in dipole moment in InAs quantum dots

We have fabricated a Schottky diode embedding InAs self-assembled quantum dots (QDs) grown by alternately supplying In and As sources. As a function of the electric field, we have investigated the photoluminescence (PL) for the InAs QDs in the Schottky diode at 300 K. We controlled the electric field in order that the QD layer was located in the depletion region of Schottky diode. The relationship between the electric field and the depletion width of the Schottky diode was deduced through the capacitance-voltage measurement. The Stark shift was observed in PL spectra for QDs; the energy of the PL line shifted to the lower energy as the electric field increased. It was also observed that the PL emission intensity gradually decreased. By the fitting to the experimental data, we determined a built-in dipole moment, corresponding to an electron-hole separation.     

Low-macroscopic field emission from silicon-incorporated diamond-like carbon film synthesized by dc PECVD

Silicon-incorporated diamond-like carbon (Si-DLC) films were deposited via dc plasma-enhanced chemical vapor deposition (PECVD), on glass and alumina substrates at a substrate temperature 300 °C. The precursor gas used was acetylene and for Si incorporation, tetraethyl orthosilicate dissolved in methanol was used. Si atomic percentage in the films was varied from 0% to 19.3% as measured from energy-dispersive X-ray analysis (EDX). The binding energies of C 1s, Si 2s and Si 2p were determined from X-ray photoelectron spectroscopic studies. We have observed low-macroscopic field electron emission from Si-DLC thin films deposited on glass substrates. The emission properties have been studied for a fixed anode-sample separation of 80 μm for different Si atomic percentages in the films. The turn-on field was also found to vary from 16.19 to 3.61 V/μm for a fixed anode-sample separation of 80 μm with a variation of silicon atomic percentage in the films 0% to 19.3%. The turn-on field and approximate work function are calculated and we have tried to explain the emission mechanism there from. It was found that the turn-on field and effective emission barrier were reduced by Si incorporation than undoped DLC.     

Infrared laser stark shift spectroscopy in ammonia

The Stark effect in ammonia has been theoretically and experimentally analyzed using lead salt tunable diode laser absorption spectroscopy and CO₂ laser absorption spectroscopy of several absorption lines around 1050 cm^–1 applied to an all-optical sensor for measuring of electric field strength. Measurements of the Stark splitting effect of theaR(5,K) ammonia lines forK=1–5 as well as for the sR(3,K) lines forK=0–3 have been made at Doppler broadening pressures and for several different electric field strengths. Theoretical electric field dependent energy levels have been evaluated by diagonalization of a 6×6 energy matrix constructed using both electric field independent and dependent terms. From the theoretical analysis the resolution can be predicted and optimized both in the Doppler broadened and in the pressure broadened regimes. The predicted resolution is 0.5% at an electric field strength of 20 kV/cm. The theoretical calculations and the experimental data recorded with the tunable diode laser system were compared with independent measurements made with a CO₂ laser system. The agreement between experimentally recorded and theoretically calculated spectra is good which indicates that the theoretical model is satisfactory for our purposes. The contribution from the normally forbidden ssR(5, 3) ammonia line to the absorption at theP(12) CO₂ laser line in the 9 m band is briefly discussed.     

SK analysis of the volt-ampere characteristics in graphene-based nanocomposite field emitters

Technical Physics - A method that enables the online processing of the experimental field emission data for the large-area emitters has been developed. This is based on an analysis of the SK...