Tunable photocatalytic selectivity of fluoropolymer PVDF modified TiO2

Fluoropolymer poly-vinylidene-fluoride modified TiO₂ (PVDF/TiO₂) were prepared via a simple chemisorption approach and characterized by thermo gravimetric analyse, transmission electron microscope, X-ray diffraction, X-ray photoelectron spectroscopy and photoluminescence spectra. The modified mechanism and the photocatalytic selectivity of the PVDF/TiO₂ were studied. The existence of Ti-F coordination bond on the interface between TiO₂ and PVDF was confirmed. For the PVDF modification, the photocatalytic degradation (PCD) of cationic dye was greatly enhanced, and the PCD of anionic dye was obviously inhibited. PVDF/TiO₂ shows high photocatalytic selectivity than that of TiO₂ by degrading mixed solution of cationic dyes MB and anionic dyes MO. The selectivity can be tuned by changing the PVDF modification amount.     

Solid-phase photocatalytic degradation of polystyrene plastic with goethite modified by boron under UV-vis light irradiation

A novel photodegradable polyethylene-boron-goethite (PE-B-goethite) composite film was prepared by embedding the boron-doped goethite into the commercial polyethylene. The goethite catalyst was modified by boron in order to improve its photocatalytic efficiency under the ultraviolet and visible light irradiation. Solid-phase photocatalytic degradation of the PE-B-goethite composite film was carried out in an ambient air at room temperature under ultraviolet and visible light irradiation. The properties of composite films were compared with those of the pure PE films and the PE-goethite composite films through performing weight loss monitoring, scanning electron microscope (SEM) analysis, FT-IR spectroscopy and X-ray photoelectron spectroscopy (XPS). The photo-induced degradation of PE-B-goethite composite films was higher than that of the pure PE films and the PE-goethite composite films under the UV-irradiation, while there has been little change under the visible light irradiation. The weight loss of the PE-B-goethite (0.4 wt.%) composite film reached 12.6% under the UV-irradiation for 300 h. The photocatalytic degradation mechanism of the composite films was briefly discussed.     

The enhanced photocatalytic activity of CdS/TiO2 nanocomposites by controlling CdS dispersion on TiO2 nanotubes

CdS/TiO₂ nanocomposites were prepared via a simple wet chemical method, and characterized through X-ray diffraction (XRD) and transmission electron microscopy (TEM). Their ability to degrade Acid Rhodamine B was investigated under visible light irradiation. The results indicate that CdS/TiO₂ nanocomposite with a mass ratio of 4:1(TiO₂:CdS) showed high photocatalytic activity and the CdS loaded on TiO₂ nanotube surface exhibited a hexagonal phase. The dispersion of CdS on TiO₂ nanotube surface had an important effect on the degradation efficiency of pollutant, which provides a strategy for practical industry application.     

Characterization and photocatalytic activity of Zn–TiO2/AC composite photocatalyst

Activated carbon (AC) supported Zn²⁺–TiO₂ photocatalyst was prepared by sol–gel method. The prepared samples were characterized by X-ray diffraction, scanning electron micrograph, nitrogen absorption, diffuse reflectance UV/VIS and X-ray photoelectron spectroscopy. Using toluene as a pollution target, the photocatalytic activity of photocatalyst was evaluated. The results showed that prepared photocatalyst was obviously helpful for the removal of toluene in air. The photocatalytic degradation of toluene by Zn²⁺–TiO₂/AC reached 100% for 40 min and remained 75% after 160 min, while degradation by TiO₂ was only 30%. It indicated that the photocatalytic activity of prepared photocatalyst was enhanced. It is due to Zn²⁺-doping increased the oxidation and reduction of hole–electron pairs, which was the important factor in heterogeneous photocatalysis.     

Methylene blue photoelectrodegradation under UV irradiation on Au/Pd-modified TiO2 films

In this work TiO₂ thin films were modified with gold/palladium (Au/Pd) bimetallic paticles by sputtering method. TiO₂ films were deposited on ITO (SnO₂:In) by Doctor Blade method and post-anneling. The properties of the films were studied through measurements of XRD (X-ray diffraction) and AFM (atomic force microscopy). The degradation of methylene blue was studied by UV-irradiated pure TiO₂ and Au/Pd-modified TiO₂ in aqueous solution. Langmuir-Hinshelwood model was used to obtain kinetic information. Photocatalytic study indicated that Au/Pd-modified TiO₂ photocatalytic activity was better than TiO₂ pure; the best half-life time for Au/Pd-modified TiO₂ in photodegradation was 2.8 times smaller than TiO₂ pure; finally the efficiency in methylene blue photodegradation was improved from 23% to 43% when Au/Pd-modified TiO₂ films were used.     

Synthesis of fluorinated TiO2 hollow microspheres and their photocatalytic activity under visible light

Fluorinated TiO₂ hollow microspheres with three-dimensional hierarchical architecture were prepared by solvothermally treatment using solid microspheres as precursor. The obtained solid and hollow TiO₂ microspheres were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM), Brunauer-Emmett-Teller (BET), X-ray photoelectron spectroscopy (XPS), UV-Vis diffuse reflectance spectrum (DRS) and photoluminescence (PL) spectra. The photocatalytic activity of as-prepared solid and hollow TiO₂ microspheres was determined by degradation of methyl orange (MO) under visible light irradiation. The results showed that the surface fluorination, the existence of accessible mesopores channels, and the increased light harvesting abilities could remarkably improve the photocatalytic activity of TiO₂ hollow microspheres.     

Comparison of photocatalytic performance of anatase TiO2 prepared by low and high temperature route

Anatase TiO₂ was prepared by a facile sol-gel method at low temperature through tailoring the pH of sol-gel without calcination. As a control, anatase TiO₂ was also synthesized by the conventional sol-gel process, in which calcination at 500 °C was required to transform the amorphous oxide into highly crystalline anatase. As-prepared samples were characterized by X-ray powder diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and photoluminescence spectroscopy (PL). Their photocatalytic activities were evaluated by degradation of methyl orange under UV light irradiation. On the basis of experiment results, it could be concluded that TiO₂ prepared by low temperature route showed more advantages in small particle size, highly dispersion nature, abundance of surface hydroxyl groups, strong PL signal, and high photocatalytic activity over TiO₂ obtained by the conventional sol-gel process. Furthermore, the reason of the former possessing higher photocatalytic activity was discussed.     

Enhanced cyclability of CdS/TiO2 photocatalyst by stable interface structure

CdS nanoparticles were in situ deposited on TiO₂ nanosheets and nanorods under hydrothermal conditions, respectively. The effect of CdS–TiO₂ interface structure on hydrogen production activity was mainly investigated under visible light irradiation. The results showed that the TiO₂ nanosheet-based CdS/TiO₂ showed a higher activity and a higher cyclability than the nanorod-based sample due to the stronger interaction of CdS with the (0 0 1) facets of TiO₂ than with the (1 0 1) facets. It was proposed that the strong interaction between CdS nanoparticles and TiO₂ nanosheets effectively refrains the recombination of electrons and holes.     

Structural, photochemical and photocatalytic properties of zirconium oxide doped TiO2 nanocrystallites

Composite photocatalysts composed of TiO₂ and ZrO₂ have been prepared via the sol-gel method. The as-prepared nanocomposites are characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), UV-vis spectrometry and fluorescence emission spectra. The results shows that TiO₂/ZrO₂ nanocomposites are composed of mainly anatase titania and tetragonal ZrO₂. Incorporating TiO₂ particles with ZrO₂ plays an important role in promoting the formation of nanoparticles with an anatase structure and leads to decreased fluorescence emission intensity. Most of the TiO₂/ZrO₂ nanocomposites exhibited comparable photocatalytic activity compared with commercial TiO₂ for the degradation aqueous methyl orange (MO) under ultraviolet irradiation, while the composite with Zr/Ti mass ratio of 15.2% shows the highest photocatalytic performances. Furthermore, the as-prepared nanocomposites can be reused with little photocatalytic activity loss. Without any further treatment besides rinsing, the photocatalytic activity of TiO₂/ZrO₂ (15.2%) composites is still higher than after five-cycle utilization.     

Enhanced visible light photocatalytic properties of Fe-doped TiO2 nanorod clusters and monodispersed nanoparticles

In order to get photocatalysts with desired morphologies and enhanced visible light responses, the Fe-doped TiO₂ nanorod clusters and monodispersed nanoparticles were prepared by modified hydrothermal and solvothermal method, respectively. The microstructures and morphologies of TiO₂ crystals can be controlled by restraining the hydrolytic reaction rates. The Fe-doped photocatalysts were characterized by X-ray diffraction (XRD), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), UV-vis absorption spectroscopy (UV-vis), N₂ adsorption-desorption measurement (BET), and photoluminescence spectroscopy (PL). The refinements of the microstructures and morphologies result in the enhancement of the specific surface areas. The Fe³⁺-dopants in TiO₂ lattices not only lead to the significantly extending of the optical responses from UV to visible region but also diminish the recombination rates of the electrons and holes. The photocatalytic activities were evaluated by photocatalytic decomposition of formaldehyde in air under visible light illumination. Compared with P25 (TiO₂) and N-doped TiO₂ nanoparticles, the Fe-doped photocatalysts show high photocatalytic activities under visible light.     

Design and fabrication of a TiO2/nano-silicon composite visible light photocatalyst

Nano-silicon (nc-Si) was utilized as the charges generator to promote the photocatalytic and super-hydrophilic reactivity of TiO₂ film under visible light irradiation. The photocatalytic ability of TiO₂/nc-Si composite photocatalyst was evaluated by a set of experiments to photodecompose 100 ppm methylene blue (MB) in aqueous solution. And the super-hydrophilic property was characterized by measuring the water droplet contacts angle, under visible light irradiation in atmospheric air and at room temperature. Under 100 mW/cm² visible light irradiation, the droplet contact angles were reduced to 0° within 4 h with nc-Si charge generator. Additionally, the rate constant of MB photo-degradation was promoted 6.6 times.     

Effect of post heat treatment on microstructure and photocatalytic activities of TiO2 nanoribbons

Low-dimensional TiO₂ nanoribbons were synthesized by a simple one-step hydrothermal method. The TiO₂ nanoribbons were calcined over the temperature range 200-800 °C in order to enhance their photocatalytic properties by altering their crystal phase and increasing crystallization. Effects of hydrothermal temperature, calcinated temperature and calcination time on the formation of nanostructures have been observed and characterized by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The (BET) specific surface area of the samples which with different post treatments were determined by N₂ absorption-desorption experiment. In addition, photocatalytic activities of the nanoribbons were evaluated by photodegradation of organic dyes methyl orange under the radiation of UV light. The results reveal that the post-treatments have great effects on the microstructures and the photocatalytic activities of TiO₂ nanoribbons.     

Preparation of continuous TiO2 fibers by sol-gel method and its photocatalytic degradation on formaldehyde

The continuous TiO₂ fibers were prepared by sol-gel method using the tetrabutyl orthotitanate as the precursor. The sol-formation process is studied by FT-IR spectroscopy. The synthesized continuous TiO₂ fibers were characterized using SEM, HRTEM and XRD. Results demonstrate that the titanate sol has good spinnability when R ≤ 2 (R = H₂O:Ti(OC₄H₉)₄, molar ratio). The fibers have the length of several meters and the diameter of about 30 μm. The fibers are a radial close-packed product of nano-particles with high crystallinity. The continuous TiO₂ fibers are co-crystal including anatase phase and rutile phase. The formaldehyde degradation ratio of continuous TiO₂ fiber was 98.6%.     

N-doped TiO2 photo-catalyst for the degradation of 1,2-dichloroethane under fluorescent light

The photo-catalytic degradation of 1,2-dichloroethane (1, 2-DCE) using nitrogen-doped TiO₂ photo-catalysts under fluorescent light irradiation was investigated. Highly pure TiO₂ and nitrogen-doped TiO₂ were prepared by a sol-gel method and characterized by thermo-gravimetric/differential-thermal analysis (TG/DTA), X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared (FTIR) spectroscopy. The results indicate that the photo-catalysts were mainly nano-size with an anatase-phase structure. The degradation reaction of 1,2-DCE was operated under visible-light irradiation, and the photo-catalytic oxidation was conducted in a batch photo-reactor with various nitrogen doping ratios (N/Ti = 0-25 mol%). The relative humidity (RH) was controlled at 0-20% and the oxygen concentration was controlled at 0-21%. The photo-degradation with nitrogen-doped TiO₂ showed superior photo-catalytic activity compared to that for pure TiO₂. TiO₂ doped with 15 mol% nitrogen exhibited the best photo-catalytic efficiency under the tested conditions. The products from the 1,2-DCE photo-catalytic oxidation were CO₂ and water; the by-products included dichloromethane, methyl chloride, ethyl chloride, carbon monoxide, and hydrogen chloride. The reaction pathway of 1,2-DCE indicates that oxygen molecules are the major factor that causes the degradation of 1,2-DCE in the gas phase.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

Photocatalytic degradation of BTEX using W-doped TiO2 immobilized on fiberglass cloth under visible light

W-doped TiO₂ were immobilized on fiberglass cloth (FGC). The catalyst possessed small crystallite sizes with a red-shift on an absorption edge. Good dispersion was observed over the immobilized catalyst. The photocatalytic degradation of gaseous BTEX was conducted in a flow reactor under day-light fluorescent. Parameters including gas flowrate, catalyst loading, initial concentration and relative humidity (%RH) were investigated. The prepared catalysts showed higher efficiency than that of TiO₂ approximately 18, 3, 3 and 2.5× for benzene, toluene, ethylbenzene and o-xylene, respectively. The condition to achieve 100% BTEX removal was found at 20 min/ml, catalyst loading 0.1 mg/cm² and 30% RH.     

Enhancement of the photocatalytic activity of TiO2 nanoparticles by surface-capping DBS groups

TiO₂ nanoparticles capped with sodium dodecylbenzenesulfonate (DBS) are synthesized by a sol-hydrothermal process using tetrabutyl titanate and DBS as raw materials. The effects of surface-capping DBS on the surface photovoltage spectroscopy (SPS), photoluminescence (PL) and photocatalytic performance of TiO₂ nanoparticles are principally investigated together with their relationships. The results show that the surface of TiO₂ nanoparticles can be well capped by DBS groups while the pH value and added DBS amount are controlled at 5.0 and 2% of TiO₂ mass weight, respectively, and the linkage between DBS groups and TiO₂ surfaces is mainly by means of quasi-sulphonate bond. The intensities of SPS and PL spectra of TiO₂ obviously decrease after DBS-capping, while the activity can greatly increase during the photocatalytic degradation of Rhodamine B (RhB) solution, which are mainly attributed to the electron-withdrawing character of the DBS groups. Moreover, the enhancement of photocatalytic activity of DBS-capped TiO₂ is also related to the increase in the capability for adsorbing RhB.     

Flowerlike PtCl4/Bi2WO6 composite photocatalyst with enhanced visible-light-induced photocatalytic activity

Flowerlike PtCl₄/Bi₂WO₆ composite photocatalyst was successfully synthesized through a simple two-step method involving a template-free hydrothermal process and the following impregnation treatment. The samples were fully characterized by the study of X-ray diffraction (XRD), field emission scanning electron microscopy (FESEM), X-ray photoelectron spectroscopy (XPS), and UV-Vis absorption spectra. The results indicated that the doping of Pt species did not affect the crystal structure and the morphology of Bi₂WO₆ photocatalyst, but it had great influences on the photocatalytic activity of Bi₂WO₆ towards rhodamine-B (RhB) degradation. Besides, the Pt species was found to be present as PtCl₄ in the composite samples, and also an optimal Pt species content on the surface of Bi₂WO₆ photocatalyst was discovered with the highest photocatalytic ability. The improved photocatalytic performance could be ascribed to the enhanced interfacial charge transfer and the inhibited recombination of electron-hole pairs. Meanwhile, a possible mechanism for RhB photocatalytic degradation over PtCl₄/Bi₂WO₆ catalyst was also proposed.     

Preparation, characterization and visible-light photocatalytic activity of AgI/AgCl/TiO2

In this paper, a novel composite photocatalyst AgI/AgCl/TiO₂ was prepared by ion exchange method and characterized by XRD, SEM and UV-Vis spectrometry. The as-prepared AgI/AgCl/TiO₂ composites show much higher photocatalytic activity than AgCl/TiO₂ and AgI/TiO₂ under visible-light irradiation (λ > 400 nm) in the process of methyl orange (MO) degradation. When the molar percentage of AgI to initial AgCl is 20% (sample SE-20%), the maximal degradation efficiency of MO has reached 85.8% after irradiation for 120 min. The enhancement of photocatalytic activity of the composite photocatalyst AgI/AgCl/TiO₂ will be attributed to its good absorption in the visible-light region, especially low recombination rate of the electron-hole pairs based on the photoluminescence (PL) spectra investigation of AgI/AgCl/TiO₂ and the matching band structures of AgI, AgCl and TiO₂. The detection of reactive species by radical scavengers displays that O₂⁻ and H₂O₂ are the main reactive species for the degradation of MO under visible-light irradiation. Moreover, PL analysis by using terephthalic acid (TA) as a probe molecule further reveals that OH can be negligible for the degradation of MO.     

Properties of carbon and iron modified TiO2 photocatalyst synthesized at low temperature and photodegradation of acid orange 7 under visible light

The nanoparticles of TiO₂ modified with carbon and iron were synthesized by sol-gel followed solvothermal method at low temperature. Its chemical composition and optical absorption were investigated by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), photoluminescence emission spectroscopy (PL), UV-vis absorption spectroscopy, and electron paramagnetic resonance (EPR). It was found that carbon and iron modification causes the absorption edge of TiO₂ to shift the visible light region. Fe(III) cation could be doped into the matrix of TiO₂, by which could hinder the recombination rate of excited electrons/holes. Superior photocatalytic activity of TiO₂ modified with carbon and iron was observed for the decomposition of acid orange 7 (AO7) under visible light irradiation. The synergistic effects of carbon and iron in modified TiO₂ nanoparticles were responsible for improving visible light photocatalytic activity.