Opto-electrical properties of Ti-doped In2O3 thin films grown by pulsed laser deposition

By ablating titanium containing In₂O₃ target with a KrF excimer laser, highly conducting and transparent films on quartz were obtained to investigate the effects of growth temperature and oxygen pressure on the structural, optical and electrical properties of these films. We find that the transparency of the films depends more on the growth temperature and less on the oxygen pressure. Electrical properties, however, are found to be sensitive to both the growth temperature and oxygen pressure. We report in this paper that a growth temperature of 500 °C and an oxygen pressure of 7.5 × 10⁻⁷ bar lead to titanium-doped indium oxide films which have high mobility (up to 199 cm² V⁻¹ s⁻¹), low resistivity (9.8 × 10⁻⁵ Ω cm), and relatively high transmittance (∼88%).     

Structural, optical and electrical characterization of highly conducting Mo-doped In2O3 thin films

Highly conducting and transparent thin films of molybdenum-doped indium oxide were deposited on quartz by pulsed laser deposition. The effect of growth temperature and oxygen partial pressure on the structural, optical and electrical properties was studied. We find that the film transparency depends on the growth temperature. The average transmittance of the films grown at different temperatures is in range of 48-87%. The X-ray diffraction results show that the films grown at low temperature are amorphous while the films grown at higher temperature are crystalline. Electrical properties are found to be sensitive to both the growth temperature and oxygen pressure. Resistivity of the films decreases from 1.3 × 10⁻³ Ω cm to 8.9 × 10⁻⁵ Ω cm while mobility increases from 9 cm²/V s to 138 cm²/V s as the growth temperature increases from room temperature to 700 °C. However, with increase in oxygen pressure, resistivity increases but the mobility decreases after attaining a maximum. The temperature-dependent resistivity measurements show transition form semiconductor to metallic behavior. The film grown at 500 °C under an oxygen pressure of 1.0 × 10⁻³ mbar is found to exhibit high mobility (250 cm²/V s), low resistivity (6.7 × 10⁻⁵ Ω cm), and relatively high transmittance (∼90%).     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.     

Growth mechanism and optoelectronic properties of nanocrystalline In2O3 films prepared by chemical spray pyrolysis of metal-organic precursor

Thin films of indium oxide, In₂O₃, were deposited by chemical spray pyrolysis technique, using aqueous alcoholic solutions of indium acetylacetonate (In-acac) precursor, on glass substrates kept at temperatures between 300 and 500 °C. The structural, optical, and electrical properties have been investigated as a function of deposition temperature, precursor concentration, carrier gas pressure, and substrate-to-nozzle distance. X-ray diffraction studies showed that the formation of nanocrystalline In₂O₃ films is preferentially oriented along (2 2 2) plane. The surface morphological modifications with substrate temperature were observed using scanning electron and atomic force microscopic studies. Optical transmittance behavior of the films in the visible and IR region was strongly affected by the deposition parameters. The optical band gap values observed are between 3.53 and 3.68 eV. The long wavelength limit of refractive index is 1.83. The Hall mobility is found to vary from 23 to 37 cm²/V s and carrier density is found nearly constant at about 10²⁰ cm⁻³.     

Synthesis and materials properties of transparent conducting In2O3 films prepared by sol-gel-spin coating technique

Transparent conducting indium oxide (In₂O₃) thin films have been prepared on glass substrates by the simple sol-gel-spin coating technique. These films have been characterized by X-ray diffraction, resistivity and Hall effect measurements, optical transmission, scanning electron microscopy and atomic force microscopy for their structural, electrical, optical and morphological properties. The influence of spin parameters, number of coating, process temperature on the quality of In₂O₃ films are studied. In the operating range of deposition, 400-475 °C, all the films showed predominant (2 2 2) orientation. Films deposited at optimum process conditions exhibited a resistivity of 2×10⁻² Ω cm along with the average transmittance of about 80% in the visible spectral range (400-700 nm).     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Studies on the effect of nozzle-to-substrate distance on the structural, electrical and optical properties of spray deposited CdIn2O4 thin films

The physical, chemical, electrical and optical properties of as-deposited and annealed CdIn₂O₄ thin films deposited using spray pyrolysis technique at different nozzle-to-substrate distances are reported. These films are characterized by X-ray diffraction, XPS, SEM, PL, Hall effect measurement techniques and optical absorption studies. The average film thickness lies within 600-800 nm range. The X-ray diffraction study shows that films exhibit cubic structure with orientation along (3 1 1) plane. The XPS study reveals that CdIn₂O₄ films are oxygen deficient. Room temperature PL indicates the presence of green shift with oxygen vacancies. The typical films show very smooth morphology. The best films deposited with optimum nozzle-to-substrate distance (NSD) of 30 cm, has minimum resistivity of 1.3 × 10⁻³ Ω cm and 2.6 × 10⁻⁴ Ω⁻¹ figure of merit. The band gap energy varies from 3.04 to 3.2 eV with change in NSD for annealed films. The effect of NSD as well as the annealing treatment resulted into the improvement of the structural, electrical and optical properties of the studied CdIn₂O₄ thin films.     

Effect of substrate temperature on properties of multilayer thin film based on ZnO and Mo-doped indium oxide

Zinc oxide/molybdenum-doped indium oxide/zinc oxide (ZnO/IMO/ZnO) multilayer thin films are grown using pulsed laser deposition technique. The effect of substrate temperature on structural, optical, and electrical properties of multilayer films is studied. It is observed that films grown at high substrate temperature are oriented along (0 0 2) and (2 2 2) direction for ZnO and IMO respectively. The crystallinity of these films increases with increase in substrate temperature. It is also seen that conductivity, carrier concentration, and mobility increase with increase in temperature. The multilayer film grown at 500 °C has low resistivity (7.67 × 10⁻⁵ Ω cm), high carrier concentration (3.90 × 10²⁰ cm⁻³), and high mobility (209 cm²/Vs).     

Structure and electrical properties of CdIn2O4 thin films prepared by DC reactive magnetron sputtering

CdIn₂O₄ thin films were prepared by direct-current (DC) reactive magnetron sputtering. The structure, surface morphology and the chemical composition of the thin films were analyzed by X-ray diffraction (XRD), atomic force microscope (AFM) and X-ray photoelectron spectroscopy (XPS), respectively. The electrical properties of the films prepared in different oxygen concentration and annealing treatment were determined, and the effects of the preparing conditions on the structure and electrical properties were also explored. It indicates that the CdIn₂O₄ thin films with uniform and dense surface morphology contain mainly CdIn₂O₄, In₂O₃ phases, and CdO phase is also observed. The XPS analysis confirms the films are in oxygen-deficient state. The electrical properties of these films significantly depend on the preparing conditions, the resistivity of the films with the oxygen concentration of 4.29% is 2.95 × 10⁻⁴ Ω cm and the Hall mobility is as high as 60.32 cm²/V s. Annealing treatment can improve the electrical performance of the films.     

Electrical, structural, and optical properties of ITO thin films prepared at room temperature by pulsed laser deposition

Indium tin oxide (ITO) thin films were prepared by pulsed laser deposition (PLD) on glass substrate at room temperature. Structural, optical, and electrical properties of these films were analyzed in order to investigate its dependence on oxygen pressure, and rapid thermal annealing (RTA) temperature. High quality ITO films with a low resistivity of 3.3 × 10⁻⁴ Ω cm and a transparency above 90% were able to be formed at an oxygen pressure of 2.0 Pa and an RTA temperature of 400 °C. A four-point probe method, X-ray diffraction (XRD), atomic force microscopy (AFM), and UV-NIR grating spectrometer are used to investigate the properties of ITO films.     

Spray pyrolytic deposition of solid electrolyte Bi2V0.9Cu0.1O5.35 films

Copper substituted bismuth vanadate films have been successfully deposited first time by spray pyrolysis technique on glass substrates suitable for low temperature solid oxide fuel cells. Desired phase formation of polycrystalline Bi₂V_0.9Cu_0.1O_5.35 (BICUVOX.10) was confirmed by X-ray diffraction technique. These films were further studied with EDAX and SEM techniques for their compositional and morphological characterization. Electrical conductivity of BICUVOX.10 is found to be 5.7 × 10⁻² (Ω cm)⁻¹ at 698 K, predicts the onset temperature for ionic contribution suitable for low temperature SOFC applications. Room temperature complex impedance plot reveals that electrical process arises due to contribution from the grain interior.     

Mechanical reliability of transparent conducting IZTO film electrodes for flexible panel displays

The mechanical reliability of transparent In-Zn-Sn-O (IZTO) films grown using pulsed DC magnetron sputtering with a single oxide alloyed ceramic target on a transparent polyimide (PI) substrate at room temperature is investigated. All IZTO films deposited at room temperature have an amorphous structure. However, their optical and electrical properties change depending on the oxygen partial pressure applied during depositing process. At an oxygen partial pressure of 3%, the films exhibit a resistivity of 8.3 × 10⁻⁴ Ω cm and an optical transmittance of 86%. Outer bending tests show that the critical bending radius decreases from 10 mm to 7.5 mm when the oxygen partial pressure increases from 1% to 3%. In the inner bending test, the critical bending radius is independent of oxygen partial pressure at 3.5 mm, indicating excellent film flexibility. In the dynamic fatigue test, the electrical resistance of the films reduces by less than 1% for more than 2000 bending cycles. These results suggest that IZTO films have excellent mechanical durability and flexibility in comparison to ITO films.     

Studies on the structural and electrical properties of F-doped SnO2 film prepared by APCVD

Fluorine-doped tin oxide films (SnO₂:F, FTO) were deposited by atmosphere pressure chemical vapor deposition (APCVD) on Na-Ca-Si glass coated with a diffusion barrier layer of SiO_xC_y. The effects of post-heating time at 700 °C on the structural and electrical properties of SnO₂:F films were investigated. The results showed that SnO₂:F films were polycrystalline with tetragonal SnO₂ structure, SnO phase was present in SnO₂ film, and abnormal grain growth was observed. The element distribution in the film depth was measured with X-ray photoelectron spectroscopy (XPS) and revealed that when the heating time increased from 202 s to 262 s, the oxygen content in the surface increased from 78.63% to 83.38%. The resistivity increased from 3.13 × 10⁻⁴ for as-deposited films to 4.73 × 10⁻⁴ Ω cm when post-heated for 262 s. Hall mobility is limited by the ionized impurity scattering rather than the grain boundary scattering.     

Electrical properties of La2O3 thin films grown on TiN/Si substrates via atomic layer deposition

The electrical as well as the structural properties of La₂O₃ thin films on TiN substrates were investigated. Amorphous stoichiometric La₂O₃ thin films were grown at 300 °C via atomic layer deposition technique by using lanthanum 2,2,6,6-tetramethyl-3,5-heptanedione [La(TMHD)₃] and H₂O as precursors. Post-annealing of the grown film induced dramatic changes in structural and the electrical properties. Crystalline phases of the La₂O₃ film emerged with the increase of the post-annealing temperature. Metal-insulator-metal (MIM) capacitor was fabricated to measure the electrical properties of the grown film. The dielectric constant of the La₂O₃ thin films increased with annealing temperature to reach the value of 17.3 at 500 °C. The leakage current density of the film post-annealed at 400 °C was estimated to be 2.78 × 10⁻¹⁰ and 2.1 × 10⁻⁸ A/cm² at ±1 V, respectively.     

Research on the properties of ZnO thin films deposited by using filtered cathodic arc plasma technique on glass substrate under different flow rate of O2

ZnO thin film has been deposited on the glass substrate at a temperature of 200 °C using the filtered cathodic arc plasma (FCAP) technique with the oxygen flow rate of 1.0, 3.0, 5.0, 7.0, 9.0 and 10.0 sccm. The deposition processes are only held in pure oxygen atmosphere. The as-grown films exhibit a polycrystalline hexagonal wurtzite structure. With the oxygen flow rate increase, the crystallinity of the samples first increases and then decreases as measured by X-ray diffractometry (XRD). And the tensile stress exists in all the as-grown thin films. The small grain with a mean diameter of 13 nm is observed by the field emission scanning electron microscopy (FESEM). The electrical resistivity values of the thin films are very low ranging from 5.42 × 10⁻³ Ω cm to 4.0 × 10⁻² Ω cm. According to the result from room temperature photoluminescence spectra measurement, the luminescent bands also depend on the oxygen supply.     

Deposition of nanostructured crystalline and corrosion resistant alumina film on bell metal at low temperature by rf magnetron sputtering

Aluminium oxide films deposited by rf magnetron sputtering for protective coatings have been investigated. The alumina films are found to exhibit grainy surface microstructure. The grain size, structure and density depend on different system parameters such as argon and/or oxygen flow rate and applied rf power etc. The effect of transition of the discharge from metallic to reactive mode on the surface characteristics of the alumina film is studied. X-ray diffractometry reveals that in poisoned mode of sputtering and under optimized power and pressure, crystalline alumina film can be grown. Different system conditions are optimized for corrosion resistant aluminium oxide films with good adhesion properties. Nanostructured alumina film is obtained at lower pressure (8 × 10⁻⁴ to 9 × 10⁻⁴ Torr) by rf reactive magnetron sputtering.     

Fabrication and vacuum annealing of transparent conductive Ga-doped Zn0.9Mg0.1O thin films prepared by pulsed laser deposition technique

In this study, highly transparent conductive Ga-doped Zn_0.9Mg_0.1O (ZMO:Ga) thin films have been deposited on glass substrates by pulsed laser deposition (PLD) technique. The effects of substrate temperature and post-deposition vacuum annealing on structural, electrical and optical properties of ZMO:Ga thin films were investigated. The properties of the films have been characterized through Hall effect, double beam spectrophotometer and X-ray diffraction. The experimental results show that the electrical resistivity of film deposited at 200 °C is 8.12 × 10⁻⁴ Ω cm, and can be further decreased to 4.74 × 10⁻⁴ Ω cm with post-deposition annealing at 400 °C for 2 h under 3 × 10⁻³ Pa. In the meantime, its band gap energy can be increased to 3.90 eV from 3.83 eV. The annealing process leads to improvement of (0 0 2) orientation, wider band gap, increased carrier concentration and blue-shift of absorption edge in the transmission spectra of ZMO:Ga thin films.     

Substrate temperature influenced structural, electrical and optical properties of dc magnetron sputtered MoO3 films

Molybdenum oxide (MoO₃) films were deposited on glass and (1 1 1) silicon substrates by sputtering of metallic molybdenum target in an oxygen partial pressure of 2 × 10⁻⁴ mbar and different substrate temperatures in the range 303-623 K using dc magnetron sputtering technique. X-ray photoelectron spectrum of the films formed at 303 K showed asymmetric Mo 3d_5/2 and Mo 3d_3/2 peaks due to the presence of mixed oxidation states of Mo⁵⁺ and Mo⁶⁺ while those deposited at substrate temperatures ≥473 K were in Mo⁶⁺ oxidation state of MoO₃. The films formed at substrate temperatures ≥473 K were polycrystalline in nature with orthorhombic α-phase MoO₃. Fourier transform infrared spectra of the films showed an absorption band at 1000 cm⁻¹ correspond to the stretching vibration of MoO, the characteristic of the α-MoO₃ phase. The electrical resistivity increased from 3.3 × 10³ to 8.3 × 10⁴ Ω cm with the increase of substrate temperature from 303 to 473 K respectively due to improvement in the crystallinity of the films. Optical band gap of the films increased from 3.03 to 3.22 eV with the increase of substrate temperature from 303 to 523 K.     

Characteristics of sandwich-structured Al2O3/HfO2/Al2O3 gate dielectric films on ultra-thin silicon-on-insulator substrates

Sandwich-structure Al₂O₃/HfO₂/Al₂O₃ gate dielectric films were grown on ultra-thin silicon-on-insulator (SOI) substrates by vacuum electron beam evaporation (EB-PVD) method. AFM and TEM observations showed that the films remained amorphous even after post-annealing treatment at 950 °C with smooth surface and clean silicon interface. EDX- and XPS-analysis results revealed no silicate or silicide at the silicon interface. The equivalent oxide thickness was 3 nm and the dielectric constant was around 7.2, as determined by electrical measurements. A fixed charge density of 3 × 10¹⁰ cm⁻² and a leakage current of 5 × 10⁻⁷A/cm² at 2 V gate bias were achieved for Au/gate stack /Si/SiO₂/Si/Au MIS capacitors. Post-annealing treatment was found to effectively reduce trap density, but increase in annealing temperature did not made any significant difference in the electrical performance.     

Effects of crystallographic orientation on the oxygen exchange rate of La0.7Sr0.3MnO3 thin films

The oxygen surface exchange of La_0.7Sr_0.3MnO₃ (LSM) thin films was investigated using the electrical conductivity relaxation (ECR) method. Epitaxial (100)-, (110)-, and (111)-oriented LSM films were fabricated on corresponding SrTiO₃ (STO) substrates using pulsed laser deposition. The LSM films had well-controlled surface qualities, exhibited bulk-like steady-state electrical properties, and exhibited surface dominated responses in ECR. The chemical surface exchange coefficients (k_chem) were determined and varied from ≈ 1 × 10^− 6 to 65 × 10^− 6 cm/s, depending on temperature and orientation, with activation energies of between 0.8 and 1.2 eV. At 800 °C, a four fold variation is observed in the k_chem values, with (110)/(100) being the highest/lowest, explained well by the high activation energy for (110), ≈ 1.16 eV, and the low energy for (111) and (100), ≈0.83 eV.