Design and analysis of miniature high-resolution omnidirectional gaze optical imaging system

A miniature high-resolution omnidirectional gaze optical imaging system comprising one optical low-pass filter and 5 lens elements with just one aspheric surface was successfully designed. The total tracking length of the system is 14.7 mm and fit on a 5MPx 2/3in CCD with 2448?×?2050 pixel of 3.45 μm for the full 360°?×?200° imaging. We introduced the difficulties in the design of ultrawide field of view system and proposed specific computations to overcome them by aberration theories, furthermore making a simulated analysis and performance evaluation using ZEMAX optical design software. The result shows that an admirable corrected field curvature along with a low F-theta distortion, and a perfect lateral and longitudinal color aberration correction were achieved; relative illumination of all field is over 68%; when the ambient temperature changes from ?40 to 70 ℃, the modulation transfer function performs in a steady range at 75 lp/mm; all of these will promote the wide-field lens application in medical, automotive, and stereo vision.     

Three-dimensional microscope tracking system using the astigmatic lens method and a profile sensor

We developed a three-dimensional microscope tracking system using the astigmatic lens method and a profile sensor, which provides three-dimensional position detection over a wide range at the rate of 3.2 kHz. First, we confirmed the range of target detection of the developed system, where the range of target detection was shown to be ±?90 µm in the horizontal plane and ±?9 µm in the vertical plane for a 10× objective lens. Next, we attempted to track a motion-controlled target. The developed system kept the target at the center of the field of view and in focus up to a target speed of 50 µm/s for a 20× objective lens. Finally, we tracked a freely moving target. We successfully demonstrated the tracking of a 10-µm-diameter polystyrene bead suspended in water for 40 min. The target was kept in the range of approximately 4.9 µm around the center of the field of view. In addition, the vertical direction was maintained in the range of ±?0.84 µm, which was sufficiently within the depth of focus.     

基于声透镜的三维光声成像技术

基于声透镜的光声成像系统中, 由样品的光声压分布等效样品的吸收分布, 进行光声像重建, 但之前的这种等效是一种近似, 理论上并不准确. 本文阐述了声透镜三维光声成像的基本原理, 揭示了声透镜像面上光声压信号的时间分布与样品轴向吸收分布之间的关系; 提出用积分法和希尔伯特变换提取光声信号瞬时值法, 解调样品吸收系数分布并重建光声像; 实验上, 对不同样品分别用积分法和希尔伯特变换法获取样品的吸收系数, 重建光声像的横向和轴向分辨率均约为1 mm, 实现了真正的三维快速光声成像.     

Adaptive multi-sample-based photoacoustic tomography with imaging quality optimization

The energy of light exposed on human skin is compulsively limited for safety reasons which affects the power of photoacoustic(PA) signal and its signal-to-noise ratio(SNR) level. Thus, the final reconstructed PA image quality is degraded. This Letter proposes an adaptive multi-sample-based approach to enhance the SNR of PA signals and in addition, detailed information in rebuilt PA images that used to be buried in the noise can be distinguished. Both ex vivo and in vivo experiments are conducted to validate the effectiveness of our proposed method which provides its potential value in clinical trials.     

Resolution enhancement of digital laser scanning fluorescence microscopy with a dual-lens optical pickup head

The resolution of the cell fluorescence image captured by a digital laser scanning microscopy with a modified dual-lens BD-ROM optical pickup head is enhanced by image registration and double sample frequency. A dual objective lens of red (655 nm) and blue (405 or 488 nm) laser sources with numerical apertures of 0.6 and 0.85 is used for sample focusing and position tracking and cell fluorescence image capturing, respectively. The image registration and capturing frequency are based on the address-coded patterns of a sample slide. The address-coded patterns are designed as a string of binary code, which comprises a plurality of base-straight lands and grooves and data-straight grooves. The widths of the base-straight lands, base-straight grooves, and data-straight grooves are 0.38, 0.38, and 0.76 μm, respectively. The numbers of sample signals in the x-direction are measured at every intersection point by intersecting the base intensity of the push–pull signal of the address-coded patterns, which has a minimum spacing of 0.38 μm. After taking a double sample frequency, the resolution of the measured cell fluorescence image is enhanced from 0.38 μm to the diffraction limit of the objective lens.     

On the defective NR-PC flat lens for lightwave target detection and imaging

Influence of the defective cylinder air holes of negative-refraction photonic crystal (NR-PC) lens on the performance of lightwave target detection and imaging are studied with finite-difference time-domain method in the paper. Numerical simulations indicate that significant enhancement of the scattering signal can be obtained using the NR-PC flat lens; consequently, great improvement of the refocusing gain as well as the imaging resolution will be provided. We further study the effect on target detection and imaging using the defective NR-PC flat lens. Using dynamic scanning scheme, it is found that its focusing resolution is better than the non-defective lens. We can also get better resolution by appropriately decreasing the radius of the defective cylinder (R = 0.3a). In conclusion, appropriate radius of the defective cylinder (R = 0.3a) will provide better image resolution.     

Optical system design of the Dyson imaging spectrometer based on the Fery prism

Imaging spectrometer has obtained wide development since rich feature information can be obtained by it; now, we focus on its high spectral resolution and miniaturization. In this paper, we design the Dyson imaging spectrometer system based on Fery prism. The average spectral resolution is 4.3 nm and the structure of the total length is 229 mm. It is a small, high-spectrometer imaging system. The front and rear surface of the traditional prism are plane, but the surfaces of the Fery prism are spherical, which can provide some optical power to realize imaging function and produce the dispersion effect. The Fery prism does not need to be placed in the parallel optical path, which simplifies the collimator lens and the imaging lens and are necessary in the prism spectrometer, making it possible to obtain a compact spectrometer. Full-spectrum transmittance of the prism is up to 94 %. Compared to the convex grating, the energy efficiency is greatly improved, and the free spectral range is wider, and its dispersion will not bring higher-order spectral aliasing problem. The small high spectrometer only includes two components. Its spectral range is from 400 to 1000 nm, covering the near-ultraviolet to near-infrared. The various aberrations of the typical spectrum are corrected. The spectrometer is excellent in performance.     

A wide-FoV athermalized infrared imaging system with a two-element lens

For infrared imaging systems to achieve wide field of view (FoV), wide operating temperature and low weight, this work designs a wide-FoV athermalized infrared imaging system (AIIS) with a two-element lens. Its principle, design, manufacture, measurement and performance validation are successively discussed. The two-element lens contains four surfaces, where three aspheric surfaces are introduced to reduce optical off-axis aberrations and a cubic surface is introduced to achieve athermalization. The key coding mask containing an aspheric surface and a cubic surface is manufactured by nano-metric machining of ion implanted material (NiIM). Experimental results validate that our wide-FoV wavefront coding AIIS has a full FoV of 26.10° and an operating temperature over –20 °C to +70 °C.     

Multi-band infrared imaging radiometer

A novel approach to multi-spectral thermal imaging using staring system has been developed. An original optical assembly has been designed set up and tested that allows to acquire simultaneously four images of the same target in different spectral bands using a single commercial IRFPA sensor and a single commercial focusing lens. The spectral and spatial separation of the four images is completely obtained by means of filters and refractive optics without any kind of scanning device or other moving part. The multi-spectral optic presented in this paper operates in the spectral region of middle infrared (3–5 μm). Spectral filters are used to select the appropriate bands of interest and they are easily interchangeable.     

大量程激光位移传感器的成像系统设计

为了解决目前国内自主研发的激光位移传感器基准工作距离短和测量范围小的问题,设计了一种适用于远距离测量的大量程激光位移传感器成像光学系统。基于激光三角测量原理,结合具体使用要求计算了大量程激光位移传感器的性能指标和成像光学系统的设计参数。选择5片式透镜结构作为系统的初始结构,利用光学设计软件对大量程激光位移传感器成像光学系统进行了仿真,完成了系统优化和性能分析,实现了基准工作距离为1 000 mm、量程为±500 mm、分辨率为0.4 mm的大量程激光位移传感器成像系统设计。结果表明,在测量范围±500 mm内,系统均可以满足成像质量要求。该激光位移传感器成像系统具有工作距离远、测量量程大、结构简单的特点,可满足1 000 mm远距离处大量程范围的测量使用要求。     

考虑磁透镜边缘场的质子成像系统优化设计

高能质子照相系统由四极磁透镜和准直器组成,实际透镜的边缘场将影响成像系统的性能.本文将含边缘场的磁场梯度用贝尔函数近似,提出了一种含边缘场的成像系统优化方法.通过Geant 4程序模拟了能量为1.6 GeV的质子成像系统,并通过优化方法给出了考虑边缘场的优化后的系统参数.研究了考虑边缘场时的成像系统参数对准直器孔径的影...     

Focusing synchrotron radiation using a polycapillary half‐focusing X‐ray lens for imaging

An imaging system based on a polycapillary half‐focusing X‐ray lens (PHFXRL) and synchrotron radiation source has been designed. The focal spot size and the gain in power density of the PHFXRL were 22 µm (FWHM) and 4648, respectively, at 14.0 keV. The spatial resolution of this new imaging system was better than 5 µm when an X‐ray charge coupled device with a pixel size of 10.9 × 10.9 µm was used. A fossil of an ancient biological specimen was imaged using this system.     

Flattop beam illumination for 3D imaging ladar with simple optical devices in the wide distance range

We have developed an illumination optical system for 3D imaging ladar (laser detection and ranging) which forms flattop beam shape by transformation of the Gaussian beam in the wide distance range. The illumination is achieved by beam division and recombination using a prism and a negative powered lens. The optimum condition of the transformation by the optical system is derived. It is confirmed that the flattop distribution can be formed in the wide range of the propagation distance from 1 to 1000 m. The experimental result with the prototype is in good agreement with the calculation result.     

3D depth-coded photoacoustic microscopy with a large field of view for human skin imaging

Photoacoustic(PA) microscopy comes with high potential for human skin imaging, since it allows noninvasively high-resolution imaging of the natural hemoglobin at depths of several millimeters. Here, we developed a PA microscopy to achieve high-resolution, high-contrast, and large field of view imaging of skin. A three-dimensional(3D) depth-coding technology was used to encode the depth information in PA images, which is very intuitive for identifying the depth of blood vessels in a two-dimensional image, and the vascular structure can be analyzed at different depths. Imaging results demonstrate that the 3D depth-coded PA microscopy should be translated from the bench to the bedside.     

Digital Micro-mirror Device-based broadband optical image sensor for robust imaging applications

To the best of the authors' knowledge, presented for the first time is the design of a robust broadband optical image sensor using a Digital Micro-mirror Device (DMD). Electronic focus control of the imaging lens and full programmability of the spatial sampling aperture shape, size, and location on the DMD plane that mechanically scans the incident incoherent optical irradiance distribution lead to imaging smartness. Dual port single-point photo-detection design provides imaging operation robustness to the global light irradiance variations such as via environmental effects, e.g., moving clouds. As the Texas Instruments (TI) DMD can provide light modulation over 400 nm to 2500 nm wavelengths, visible, Near Infrared (NIR), and Short-Wave Infrared (SWIR) bands can be simultaneously processed to generate three independent band images via three point photo-detectors. A proof-of-concept experiment in the SWIR band at 1580 nm is conducted using an incoherent heart-shaped target that is sampled using the DMD imager set for a 68.4 μm side square moving pinhole. A 60 × 60 pixel image from the proposed imager produces a 0.94 cross-correlation peak when compared to an optically attenuated heart shape image produced by a near 9 μm pixel size phosphor coated Charge Coupled Device (CCD) imager. Using the dual-detection method, robust 633 nm visible light imaging of an Air Force (AF) Chart figure is successfully demonstrated for 3 Hz global light fluctuation. Applications for the proposed imager include optical sensing in the fields of astronomy, defense, medicine, and security.     

双层塑料靶丸的X射线相衬成像

 为对微聚焦X射线相衬成像技术应用于双层以及多层塑料靶丸成像和特征分析进行可行性研究,基于类同轴X射线成像技术,综合考虑成像放大倍数、分辨率和衬度等因素,选择合适的实验参数,成功获得了较为清晰的双层塑料靶丸X射线相衬成像照片;采用数字图像处理技术的图像分割手段,如拉普拉斯高斯边缘检测法等对所成像中靶丸边界特征进行分析处理,获得了双层靶丸内层厚度为（10.5±0.6） μm,外层厚度为（9.2±0.7） μm,靶丸外径为（273.3±1.0） μm等参数。     

10m大口径薄膜衍射主镜的色差校正技术研究

分析了薄膜衍射主镜的成像性能及色散特性,利用含有衍射面的反射式消色差光路校正了衍射主镜的强色散,使成像系统的工作波段达到40nm、视场达到0.02°,设计了10m口径、115.73m总长的短结构合成孔径薄膜衍射成像系统.结果表明,消色差光路将两边缘波长0.58μm与0.62μm之间的焦距差由5.34m减小到17.27μm.该研究提供了一种薄膜衍射主镜成像系统的设计方案,可为超大口径薄膜衍射成像系统的工程化研究提供参考.     

Scanning laser microscope for imaging nanostructured superconductors

The nanofabrication of superconductors yields various interesting features in superconducting properties. A variety of different imaging techniques have been developed for probing the local superconducting profiles. A scanning pulsed laser microscope has been developed by the combination of the XYZ piezo-driven stages and an optical fiber with an aspheric focusing lens. The scanning laser microscope is used to understand the position-dependent properties of a superconducting MgB₂ stripline of length 100 μm and width of 3 μm under constant bias current. Our results show that the superconducting stripline can clearly be seen in the contour image of the scanning laser microscope on the signal voltage. It is suggested from the observed image that the inhomogeneity is relevant in specifying the operating conditions such as detection efficiency of the sensor.     

A wide-angle camera module for disposable endoscopy

A wide-angle miniaturized camera module for disposable endoscope is demonstrated in this paper. A lens module with 150° angle of view (AOV) is designed and manufactured. All plastic injection-molded lenses and a commercial CMOS image sensor are employed to reduce the manufacturing cost. The image sensor and LED illumination unit are assembled with a lens module. The camera module does not include a camera processor to further reduce its size and cost. The size of the camera module is 5.5 × 5.5 × 22.3 mm³. The diagonal field of view (FOV) of the camera module is measured to be 110°. A prototype of a disposable endoscope is implemented to perform a pre-clinical animal testing. The esophagus of an adult beagle dog is observed. These results demonstrate the feasibility of a cost-effective and high-performance camera module for disposable endoscopy.     

基于自由曲面设计的全景鱼眼光学系统

全景鱼眼光学系统的成像圆通常为完整的圆形,小于感光芯片的垂直方向尺寸,相比长方形芯片,圆形成像圆面积较小,芯片有效像素利用率低。结合全景鱼眼光学系统成像圆小于芯片的特点,介绍一种基于自由曲面设计的全景鱼眼光学系统,可实现椭圆形成像区域,大大提高芯片有效像素的利用率。采用光学设计软件,构建自由曲面模型,运用玻璃镜片加塑料镜片混合构成的方法,通过消像差和控制不同温度场下焦点漂移设计非对称全景鱼眼光学系统的成像区域为椭圆,实现了镜头成像像高X方向接近芯片的水平尺寸,Y方向接近芯片的垂直尺寸。在不考虑制造公差的理想情况下,对于4:3芯片,根据圆和椭圆面积公式可得圆形成像区域的芯片像素有效利用率约为58.9%,椭圆形成像区域的芯片像素有效利用率约为78.5%。仿真和计算结果表明,采用椭圆形成像光学设计比圆形成像光学设计的芯片有效像素利用率提升15%左右。