Self-assembled monolayers of organosulfur derivative on gold nanoparticles as electrochemical sensor for determination of isoprenaline

In this paper, the use of molecular self-assembled monolayers of 5-(1,3-dithiolan-2-eyl)-3-methyl banzen-1,2-diol (DMD) on gold nanoparticles was described (DMD-AuNPs). The redox properties of modified electrode at various scan rates were investigated by cyclic voltammetry. A pair of well-defined quasi-reversible redox peaks of DMD were obtained at the modified electrode. Dramatically enhanced electrocatalytic activity was exemplified at the DMD-AuNPs, as an electrochemical sensor to investigate the electro-oxidation of isoprenaline (IP). With this modified electrode, the oxidation potential of the IP was shifted about 235 mV toward a less positive potential value than that of an unmodified electrode. The values of electron transfer coefficients (α = 0.5), catalytic rate constant (ks = 9.2 s^?1) and diffusion coefficient (D = 8.9 × 10^?5 cm² s^?1) were calculated for IP. The response of catalytic current with IP concentration showed a linear relation in the range from 0.5 to 800 µM with a detection limit of 0.21 µM. Finally, this modified electrode was used for the determination of IP in IP injections.     

Differential pulse voltammetric simultaneous determination of ascorbic acid,dopamine and uric acid on a glassy carbon electrode modified with electroreduced graphene oxide and imidazolium groups

A glassy carbon electrode (GCE) was anodically oxidized by cyclic voltammetry (CV) in 0.05 M sulfuric acid to introduce hydroxy groups on its surface (GCE_ox). Next, an imidazolium alkoxysilane (ImAS) is covalently tethered to the surface of the GCE_ox via silane chemistry. This electrode is further modified with graphene oxide (GO) which, dispersed in water, spontaneously assembles on the electrode surface through electrostatic interaction and π-interaction to give an electrode of type GO/ImAS/GCE. Electroreduction of GO and GCE_ox by CV yields electroreduced GO (erGO) and an electrode of the type erGO/ImAS/GCE. This electrode displays excellent electrocatalytic activity for the oxidation of ascorbic acid (AA), dopamine (DA) and uric acid (UA). Three fully resolved anodic peaks (at ?50 mV, 150 mV and 280 mV vs. Ag/AgCl) are observed during differential pulse voltammetry (DPV). Under optimized conditions, the linear detection ranges are from 30 to 2000 μM for AA, from 20 to 490 μM for UA, and from 0.1 to 5 μM and from 5 μM to 200 μM (two linear ranges) for DA. The respective limits of detection (for an S/N of 3) are 10 μM, 5 μM and 0.03 μM. The GCE modified with erGO and ImAS performs better than a bare GCE or a GCE modified with ImAS only, and also outperforms many other reported electrodes for the three analytes. The method was successfully applied to simultaneous analysis of AA, DA and UA in spiked human urine.

Open image in new window

Graphical abstract Differential pulse voltammetric simultaneous determination of ascorbic acid, dopamine and uric acid is achieved on a glassy carbon electrode modified with electroreduced graphene oxide and imidazolium groups, through anodic treatment of glassy carbon and silane chemistry.

     

Simultaneous determination of hydroquinone and catechol based on glassy carbon electrode modified with gold-graphene nanocomposite

We have synthesized a virtually monodisperse gold-graphene (Au-G) nanocomposite by a single-step chemical reduction method in aqueous dimethylformamide solution. The nanoparticles are homogenously distributed over graphene nanosheets. A glassy carbon electrode was modified with this nanocomposite and displayed high electrocatalytic activity and extraordinary electronic transport properties due to its large surface area. It enabled the simultaneous determination of hydroquinone (HQ) and catechol (CC) in acetate buffer solution of pH?4.5. Two pairs of well-defined, quasi-reversible redox peaks are obtained, one for HQ and its oxidized form, with a 43 mV separation of peak potentials (ΔE_p), the other for CC and its oxidized form, with a ΔE_p of 39 mV. Due to the large separation of oxidation peak potentials (102 mV), the concentrations of HQ and CC can be easily determined simultaneously. The oxidation peak currents for both HQ and CC increase linearly with the respective concentrations in the 1.0 μM to 0.1 mM concentration range, with the detection limits of 0.2 and 0.15 μM (S/N?=?3), respectively. The modified electrode was successfully applied to the simultaneous determination of HQ and CC in spiked tap water, demonstrating that the Au-G nanocomposite may act as a high-performance sensing material in the selective detection of some environmental pollutants.

Voltammetric studies of the activity of an electrode made of a graphite-epoxy composite in redox reactions of ascorbic acid and hydroquinone

The potentials of the anodic peak of ascorbic acid oxidation and the potential differences of anodic and cathodic peaks (ΔE _p) of the hydroquinone/benzoquinone redox system at an electrode made of a graphite-epoxy composite are determined in weakly acidic and neutral supporting electrolytes by direct and cyclic voltammetry. The results obtained are compared with thermodynamic values and with the available values of these parameters at different solid electrodes for the above-mentioned redox systems. The effect of aging of the surface of electrodes made of graphite-epoxy composites on the potentials and peak currents of the anodic oxidation of ascorbic acid are studied. It is demonstrated that the regeneration of the electrode surface by mechanically cutting thin layers is important for reducing the δE _p value of the hydroquinone/benzoquinone redox system down to 28–30 mV in supporting electrolytes with pH 2.0 and 7.0. This value is typical of thermodynamically reversible electrode reactions involving two-electron transfer at 20–25°C.     

A comparison of energy changes accompanying growth processes by <Emphasis Type="Italic">Saccharomyces cerevisiae</Emphasis>

Calculations are made using the equations Δ_r G = Δ_r H ? TΔ_r S and Δ_r X = Δ_r H ? Δ_r Q where Δ_r X represents the free energy change when the exchange of absorbed thermal energy with the environment is represented by Δ_r Q. The symbol Q has traditionally represented absorbed heat. However, here it is used specifically to represent the enthalpy listed in tabulations of thermodynamic properties as (H _T  ? H ₀) at T = 298.15 K, the reason being that for a given substance TS equals 2.0 Q for solid substances, with the difference being greater for liquids, and especially gases. Since Δ_r H can be measured, and is tangibly the same no matter what thermodynamics are used to describe a reaction equation, a change in the absorbed heat of a biochemical growth process system as represented by either Δ_r Q or TΔ_r S would be expected to result in a different calculated value for the free energy change. Calculations of changes in thermodynamic properties are made which accompany anabolism; the formation of anabolic, organic by-products; catabolism; metabolism; and their respective non-conservative reactions; for the growth of Saccharomyces cerevisiae using four growth process systems. The result is that there is only about a 1% difference in the average quantity of free energy conserved during growth using either Eq. 1 or 2. This is because although values of TΔ_r S and Δ_r Q can be markedly different when compared to one another, these differences are small when compared to the value for Δ_r G or Δ_r X.     

Voltammetric determination of mercury(II) using a modified pencil graphite electrode with 4-(4-methylphenyl aminoisonitrosoacetyl)biphenyl

A sensitive and selective method for determination of mercury(II) with “4-(4-methylphenyl aminoisonitrosoacetyl)biphenyl (TKO)-modified pencil graphite electrode” was developed. All factors affecting determination process were optimized. Differential pulse voltammetry with 4-(4-methylphenyl aminoisonitrosoacetyl)biphenyl-modified electrode showed a linear response between 1.0 × 10^?5 and 1.0 × 10^?3 M (R ² = 0.9994). The detection limit of this electrode was found as 5.85 × 10^?7 M (S/N = 3). The effects of different cations on the determination of mercury(II) were investigated and found that modified electrode is highly selective. The developed method was applied for mercury determination in different water samples.     

Effect of solvents on the morphology of NiCo<Subscript>2</Subscript>O<Subscript>4</Subscript>/graphene nanostructures for electrochemical pseudocapacitor application

The large internal surface areas and outstanding electrical and mechanical properties of graphene have prompted to blend graphene with NiCo₂O₄ to fabricate nanostructured NiCo₂O₄/graphene composites for supercapacitor applications. The use of graphene as blending with NiCo₂O₄ enhances the specific capacitance and rate capability and improves the cyclic performance when compared to the pristine NiCo₂O₄ material. Here, we synthesized two different nanostructured morphologies of NiCo₂O₄ on graphene sheets by solvothermal method. It has been suggested that the morphologies of oxides are greatly influenced by dielectric constant, thermal conductivity, and viscosity of solvents employed during the synthesis. In order to test this concept, we have synthesized nanostructured NiCo₂O₄ on graphene sheets by facile solvothermal method using N-methyl pyrrolidone and N,N-dimethylformamide solvents with water. We find that mixture of N-methyl pyrrolidone and water solvent favored the formation of nanonet-like NiCo₂O₄/graphene (NiCoO-net) whereas mixture of N,N-dimethylformamide and water solvent produced microsphere-like NiCo₂O₄/graphene (NiCoO-sphere). Electrochemical pseudocapacitance behavior of the two NiCo₂O₄/graphene electrode materials was studied by cyclic voltammetry, chronopotentiometry, and electrochemical impedance spectroscopy techniques. The supercapacitance measurements on NiCoO-net and NiCoO-sphere electrodes showed specific capacitance values of 1060 and 855 F g^?1, respectively, at the current density of 1.5 A g^?1. The capacitance retention of NiCoO-net electrode is 93 % while that of NiCoO-sphere electrode is 77 % after long-term 5000 charge-discharge cycles at high current density of 10 A g^?1.     

Dopamine sensor based on a glassy carbon electrode modified with a reduced graphene oxide and palladium nanoparticles composite

We report on a sensitive electrochemical sensor for dopamine (DA) based on a glassy carbon electrode that was modified with a nanocomposite containing electrochemically reduced graphene oxide (RGO) and palladium nanoparticles (Pd-NPs). The composite was characterized by scanning electron microscopy, energy dispersive spectroscopy, and electrochemical impendence spectroscopy. The electrode can oxidize DA at lower potential (234 mV vs Ag/AgCl) than electrodes modified with RGO or Pd-NPs only. The response of the sensor to DA is linear in the 1–150 μM concentration range, and the detection limit is 0.233 μM. The sensor was applied to the determination of DA in commercial DA injection solutions.

Cluster-associated filling of water molecules in graphene-based mesopores

Graphene monoliths were prepared through unidirectional freeze-drying method of graphene oxide colloids-KOH mixed solution and successive reduction by heating at 573 K in Ar. The porosity- and crystallinity-controlled graphene monoliths were prepared by the KOH activation at different temperature and the post-heating in Ar. These activated graphene monoliths were characterized by N₂ adsorption at 77 K, X-ray diffraction and Raman spectroscopy. Water adsorption isotherms show a typical hydrophobicity below P/P ₀ = 0.5 and a marked hydrophilicity above P/P ₀ = 0.6, which depends on the pore width. In the water adsorption isotherms of porous graphene monoliths activated at different temperature, the higher the activation temperature, the larger the rising P/P ₀. No essential change in the shape of the water adsorption isotherm for the post-heated nanoporous graphene monoliths is observed except for the decrease in water adsorption amount with higher post-heating temperature. The linear relationship between the saturated water adsorption and pore volume whose width is smaller than 4 nm indicates clearly that water molecules are adsorbed in small mesopores by the cluster-associated filling mechanism.     

Sensitive Flow-Injection Electrochemical Determination of Hydrogen Peroxide at a Palladium Nanoparticle-Modified Pencil Graphite Electrode

A novel flow-injection amperometric method was proposed for the sensitive and enzymeless determination of hydrogen peroxide based on its electrocatalytic reduction at a palladium nanoparticle-modified pretreated pencil graphite electrode in a laboratory-constructed electrochemical flow cell. Cyclic voltammograms of the unmodified and modified electrodes were recorded in pH 7.0 phosphate buffer containing 0.10 M KCl at a scan rate of 50?mV s^?1 for the investigation of electrocatalytic reduction of hydrogen peroxide at the palladium nanoparticle-modified pretreated pencil graphite electrode. Cyclic voltammograms of the pretreated pencil graphite electrode revealed an irreversible oxidation peak and a weak reduction peak of hydrogen peroxide at +1100?mV and –450?mV vs. an Ag/AgCl/KCl saturated reference electrode. However, the reduction of hydrogen peroxide was observed at –100?mV with an increase in current in the cyclic voltammograms of the palladium nanoparticle-modified pretreated pencil graphite electrode compared to the unmodified electrode. These results indicate that the palladium nanoparticle-modified pretreated pencil graphite electrode exhibits efficient electrocatalytic activity for the reduction of hydrogen peroxide. A linear concentration range was obtained between .01 and 10.0?mM hydrogen peroxide with a detection limit of 3.0 µM from flow injection amperometric current–time curves recorded in pH 7.0 phosphate buffer at –100?mV and a 2.0?mL min^?1 flow rate. The novelty of this work relies on its use of a laboratory-constructed flow cell constructed for the pencil graphite electrode using these inexpensive, disposable, and electrochemically reactive modified electrodes for the amperometric determination of hydrogen peroxide in a flow injection analysis system.     

Amperometric determination of the insecticide fipronil using batch injection analysis: comparison between unmodified and carbon-nanotube-modified electrodes

The electrochemical oxidation of fipronil is investigated on unmodified and multi-walled carbon-nanotube (MWCNT)-modified glassy carbon electrodes (GCEs), and its amperometric determination using batch injection analysis (BIA) is demonstrated. An oxidation peak was observed at 1.5 V in a 0.1 mol L^?1 HClO₄/acetone solution (50:50, v/v) on both surfaces. Although MWCNT-modified GCE provided greater sensitivity, the unmodified GCE showed low RSD value, wider linear range, and reduced adsorption of fipronil or its oxidized products on the electrode surface. A detection limit of 4.7 μmol L^?1 and linear range of 25–300 μmol L^?1 were obtained using a bare GCE. The method was applied in veterinary formulations with results in agreement with those obtained by high-performance liquid chromatography.     

New acetaminophen amperometric sensor based on ferrocenyl dendrimers deposited onto Pt nanoparticles

In this work, the electrocatalytical properties and kinetic characteristics of new electrodes modified with Pt nanoparticles (PtNPs) and three generations of ferrocene functionalized dendrimers have been investigated as new acetaminophen amperometric sensors. The catalytic synergy of PtNPs with the ferrocene groups is discussed in relation to the ferrocenyl dendrimer generation and their properties. The modified electrodes show excellent catalytic responses toward the oxidation of acetaminophen, with good reproducibility. The overpotential for oxidation of acetaminophen at pH 7 is decreased, and the current response significantly enhanced. The best dendrimer/PtNPs/Pt electrode shows several wide linear concentration ranges for the acetaminophen oxidation from 0 to beyond 17 mM. At 0.5 V vs. SCE, the first linear range extends from 0 to 100 μM (y = 0.0131x ? 0.0028; R ² = 0.9996) and the last from 10 mM to at least 17 mM (y = 0.0024x + 26.6; R ² = 0.9977). This fact turns the developed acetaminophen sensor in the device with the widest application range. In addition, the sensor allows measuring acetaminophen in the presence of interfering substances as glucose, dopamine, uric acid, and ascorbic acid, and it has been successfully applied to the determination of acetaminophen in three pharmaceutical formulations.     

Incorporation of graphene oxide–NiO nanocomposite and <Emphasis Type="Italic">n</Emphasis>-hexyl-3-methylimidazolium hexafluoro phosphate into carbon paste electrode: application as an electrochemical sensor for simultaneous determination of benserazide,levodopa and tryptophan

The benserazide (BZ) and levodopa (LD) are two important catechol drugs to inhibit dopamine production outside the brain. On the other hand, BZ is effective on tryptophan (Trp) metabolism as an inhibitor aromatic amino acid decarboxylase. A voltammetric sensor based on carbon paste electrodes modified with graphene oxide–NiO nanocomposite and n-hexyl-3-methylimidazolium hexafluoro phosphate (n-H-3MIHF) as a binder is proposed to detect and quantify of BZ, LD and Trp in drug and urine samples. In square-wave voltammetry technique, BZ, LD and Trp were given sensitive oxidation peaks at 156, 312 and 740 mV, respectively. At a best electrochemical conditions, the enhanced oxidation peak currents represented the excellent analytical performance of simultaneous detection of BZ, LD and Trp in the ranges of 0.1–600, 0.1–700 and 5.0–700 μM, with a low limit of detection of 0.05 μM for BZ, 0.05 for LD and 1.0 μM for Trp (S/N = 3), respectively. To further validate its possible application, the proposed sensor was successfully used for the determination of above compounds in tablet and urine with satisfactory results.     

Evaluation of a novel composite based on functionalized multi-walled carbon nanotube and iron phthalocyanine for electroanalytical determination of isoniazid

A novel platform for electroanalysis of isoniazid based on graphene-functionalized multi-walled carbon nanotube as support for iron phthalocyanine (FePc/f-MWCNT) has been developed. The FePc/f-MWCNT composite has been dropped on glassy carbon forming FePc/f-MWCNT/GC electrode, which is sensible for isoniazid, decreasing substantially its oxidation potential to +200 mV vs Ag/AgCl. Electrochemical and electroanalytical properties of the FePc/f-MWCNT/GC-modified electrode were investigated by cyclic voltammetry, electrochemical impedance spectroscopy, scanning electrochemical microscopy, and amperometry. The sensor presents better performance in 0.1 mol L^?1 phosphate buffer at pH 7.4. Under optimized conditions, a linear response range from 5 to 476 μmol L^?1 was obtained with a limit of detection and sensitivity of 0.56 μmol L^?1 and 0.023 μA L μmol^?1, respectively. The relative standard deviation for 10 determinations of 100 μmol L^?1 isoniazid was 2.5%. The sensor was successfully applied for isoniazid selective determination in simulated body fluids.     

Kinetics of ethylene glycol electrooxidation on the noble metal-based nano-catalysts

A comparative electrooxidation of Eg in the alkaline solution was investigated over Pt, Pd and Au nanoparticle-modified carbon-ceramic electrode. The kinetic parameters of Eg oxidation, i.e., Tafel slope and activation energy (E _a), were determined on the modified electrodes. The lowest E _a value of 8.9 kJ mol^?1 was calculated on Pt|CCE. In continuation, the reaction orders with respect to the Eg and NaOH concentrations on Pd|CCE were found to be 0.4–0.2 and 0.6, respectively. An adsorption equilibrium constant (b) of 22.36 M^?1 and the adsorption Gibbs energy change (ΔG°) of ?7.7 kJ mol^?1 were obtained on Pd|CCE. The chronopotentiometry (CP) and chronoamperometry (CA) results showed that Pd|CCE and then Au|CCE have better performance stability than Pt|CCE for Eg electrooxidation. Additionally, the electrochemical impedance spectroscopy (EIS) suggested faster electron-transfer kinetics on Pt than that on the Pd and Au electrocatalysts.     

Polymer matrices with molecular memory as affine adsorbents for the determination of myoglobin as a cardiac marker of acute myocardial infarction by voltammetry

A possibility of myoglobin determination using screen-printed graphite electrodes modified with a poly(o-phenylenediamine)-based molecularly imprinted polymer (MIP) obtained by the electropolymerization of o-phenylenediamine monomer molecules on the surface of a screen-printed graphite electrode in the presence of myoglobin template molecules is considered. It is shown that the conjugation of MIP with multiwall carbon nanotubes (MWCNT) results in an increase in the sensitivity of the MIP-biosensor in the electrochemical determination of myoglobin by the direct registration of the reduction peak of hemoprotein Fe³⁺ by square wave voltammetry on screen-printed graphite electrodes modified with MWCNT/MIP and MIP. Equilibrium dissociation constants K _d for the interaction of myoglobin with MWCNT/MIP- and MIP-electrodes, which equaled (9.8 ± 2.6) × 10^–11 and (2.4 ± 0.5) × 10^–8 M, respectively, are calculated. It is shown that the sensitivity of the electrochemical MWCNT/MIP-biosensor for myoglobin determination (1.5 × 10^–2 A/nmol of myoglobin) is higher than that of the MIP-biosensor (2.0 × 10^–4 A/nmol of myoglobin).     

Voltammetric determination of dihydroxybenzenes at a mechanically renewed electrode made from a graphite-epoxy composite

Differences of potentials of anodic and cathodic peaks (ΔE _p) are determined in cyclic voltammograms of dihydroxybenzene/p-benzoquinone redox systems at an electrode made of a graphite-epoxy composite in a wide pH range. The data obtained (ΔE _p = 29 ± 1 mV) are close to the thermodynamic values for two-electron reversible reactions. This indicates that the electrode mechanically renewed by cutting a 0.5-μm surface layer directly in a test solution exhibits a high activity in such electrochemical reactions. The potentials of anodic and cathodic peaks are proportional to the pH of the supporting electrolyte solution in the range from 1.0 to 9.0. A change of 58 ± 1 mV in E _p per unit pH for all isomers shows that the first stage of the oxidation of each dihydroxybenzene isomer involves one electron and is accompanied by the detachment of one hydrogen ion, that is, an intermediate oxidation product, semiquinone, is formed. Despite the closeness of the potentials of hydroquinone and pyrocatechol peaks (ΔE = 100 mV), a scheme is proposed for the selective voltammetric determination of dihydroxybenzene isomers in a 0.1 M HCl solution in hydroquinone-pyrocatechol, pyrocatechol-resorcinol, and hydroquinone-resorcinol binary mixtures. The concentrations of hydroquinone and pyrocatechol are found from cathodic peaks and that of resorcinol, from the anodic peak. The results are well reproducible and contain no systematic error.     

Cobalt(II) porphyrazine as an active component of iodide-selective electrodes

Cobalt(II) porphyrazine is synthesized and studied as an active component of a polyvinyl chloride plasticized membrane ion-selective electrodes (ISEs). It is established that regardless of their structure, ISEs are sensitive to iodide. The introduction to the ISE of an ionic additive, ionic liquid 1,3-dihexadecylimidazolium chloride, significantly improves the electrochemical characteristics: the slope of the electrode function reaches ?(57 ± 1) mV/dec, c_min = 8.3 × 10^–6 M. Solid-state screen-printed electrodes the surfaces of which are modified by a 1: 4 mixture of cobalt(II) porphyrazine and ionic liquid 1,3-dihexadecylimidazolium chloride demonstrate satisfactory electrochemical characteristics: the slope of the electrode function is ?(56 ± 4) mV/dec and c_min = 2.5 × 10^–5 M. The potentiometric selectivity of the ISEs for iodide is studied. It is found that the effect of lipophilic interfering ions is significantly lower for solid state ISEs than for plasticized membrane electrodes.     

Electrochemical gating of single osmium molecules tethered to Au surfaces

The electrochemical study of electron transport between Au electrodes and the redox molecule Os[(bpy)₂(PyCH₂ NH₂CO-]ClO₄ tethered to molecular linkers of different length (1.3 to 2.9 nm) to Au surfaces has shown an exponential decay of the rate constant k _ET ⁰ with a slope β = 0.53 consistent with through bond tunneling to the redox center. Electrochemical gating of single osmium molecules in an asymmetric tunneling nano-gap between a Au(111) substrate electrode modified with the redox molecules and a Pt-Ir tip of a scanning tunneling microscope was achieved by independent control of the reference electrode potential in the electrolyte, E _ref ? E _s, and the tip-substrate bias potential, E _bias. Enhanced tunneling current at the osmium complex redox potential was observed as compared to the off resonance set point tunneling current with a linear dependence of the overpotential at maximum current vs. the E _bias. This corresponds to a sequential two-step electron transfer with partial vibration relaxation from the substrate Au(111) to the redox molecule in the nano-gap and from this redox state to the Pt-Ir tip according to the model of Kuznetsov and Ulstrup (J Phys Chem A 104: 11531, 2000). Comparison of short and long linkers of the osmium complex has shown the same two-step ET (electron transfer) behavior due to the long time scale in the complete reduction-oxidation cycle in the electrochemical tunneling spectroscopy (EC-STS) experiment as compared to the time constants for electron transfer for all linker distances, k _ET ⁰.     

Synthesis,structural, and electrochemical properties of NaCo(PO<Subscript>3</Subscript>)<Subscript>3</Subscript> cathode for sodium-ion batteries

A new Co-base sodium metaphosphate compound, NaCo(PO₃)₃, has been synthesized here by solid-state method. The crystal structure is refined by the Rietveld method, and the results reveal that NaCo(PO₃)₃ has an orthorhombic structure with the space group of P2 ₁ 2 ₁ 2 ₁ and lattice parameters of a = 14.2453(2) Å, b = 14.2306(1) Å, and c = 14.2603(2) Å. Its typical morphology and chemical composition are confirmed by scanning electron microscopy (SEM) and energy-dispersive spectrometry (EDS). The valence states of all elements and the internal/external vibrational modes of NaCoP₃O₉ compound are measured by X-ray photoelectron and vibrational spectrum, where a typical feature of the (PO₃)^? polyanion group is observed. Meanwhile, the electrochemical properties of NaCo(PO₃)₃ cathode for sodium-ion batteries are also elevated and an initial discharge capacity of 33.8 mAh/g can be obtained at 0.05 C within 1.5–4.2 V. After 20 cycles, a discharge capacity of 26.7 mAh/g can be obtained and a well-kept oxidation–reduction plateau is still observed for NaCo(PO₃)₃ cathode, indicating the good reversibility of this metaphosphate electrode.