Stable cycling of graphite in an ionic liquid based electrolyte

1-Ethyl-3-methylimidazolium-bis(trifluoromethylsulfonyl)imide (EMI-TFSI) has been shown to reversibly permit lithium intercalation into standard graphite when vinylene carbonate is used in small amounts as an additive.     

Ionogels, ionic liquid based hybrid materials

The current interest in ionic liquids (ILs) is motivated by some unique properties, such as negligible vapour pressure, thermal stability and non-flammability, combined with high ionic conductivity and wide electrochemical stability window. However, for material applications, there is a challenging need for immobilizing ILs in solid devices, while keeping their specific properties. In this critical review, ionogels are presented as a new class of hybrid materials, in which the properties of the IL are hybridized with those of another component, which may be organic (low molecular weight gelator, (bio)polymer), inorganic (e.g. carbon nanotubes, silica etc.) or hybrid organic-inorganic (e.g. polymer and inorganic fillers). Actually, ILs act as structuring media during the formation of inorganic ionogels, their intrinsic organization and physicochemical properties influencing the building of the solid host network. Conversely, some effects of confinement can modify some properties of the guest IL, even though liquid-like dynamics and ion mobility are preserved. Ionogels, which keep the main properties of ILs except outflow, while allowing easy shaping, considerably enlarge the array of applications of ILs. Thus, they form a promising family of solid electrolyte membranes, which gives access to all-solid devices, a topical industrial challenge in domains such as lithium batteries, fuel cells and dye-sensitized solar cells. Replacing conventional media, organic solvents in lithium batteries or water in proton-exchange-membrane fuel cells (PEMFC), by low-vapour-pressure and non flammable ILs presents major advantages such as improved safety and a higher operating temperature range. Implementation of ILs in separation techniques, where they benefit from huge advantages as well, relies again on the development of supported IL membranes such as ionogels. Moreover, functionalization of ionogels can be achieved both by incorporation of organic functions in the solid matrix, and by encapsulation of molecular species (from metal complexes to enzymes) in the immobilized IL phase, which opens new routes for designing advanced materials, especially (bio)catalytic membranes, sensors and drug release systems (194 references).     

Aqueous biphasic systems composed of ionic liquid and fructose

Liquid–liquid equilibria data of the [Bmim]BF₄ + fructose + water system were determined at 298.15, 308.15, 31815 K. It was found that the liquid–liquid equilibria can be formed over a wide component range and the effect of the temperature on the phase equilibria is obvious within the fructose concentration changing from 3 to 40%. The binodal curves were correlated using a five-parameter equation, and the tie lines were fitted the Othmer–Tobias and Bancroft correlations. Correlation coefficients for the equations exceeded 0.99.     

Electrodeposition and stripping of zinc from an ionic liquid polymer gel electrolyte for rechargeable zinc-based batteries

In this paper, we report on zinc deposition and stripping in an ionic liquid polymer gel electrolyte on gold and copper substrates, respectively. The ionic liquid-based polymer gel electrolyte is prepared by combining the ionic liquid 1-butyl-1-methylpyrrolidinium trifluoromethylsulfonate ([Py_1,4]TfO), with Zn(TfO)₂ and poly(vinylidene fluoride-co-hexafluoropropylene) (PVdF-HFP). The ionic liquid polymer gel electrolyte exhibits good conductivity (2.2 mS cm^?1) and good mechanical stability. Zinc deposition and stripping in the ionic liquid polymer gel electrolyte were studied by cyclic voltammetry, potentiostatic, and galvanostatic cycling (charging/discharging) experiments. The gel electrolyte exhibits a promising electrochemical stability and allows a quasi-reversible zinc deposition/stripping. The morphology of the zinc deposits after 10 cycles of zinc deposition/stripping is compact and dense, and deposits without any dendrite formation can be obtained. The quasi-reversibility of the electrochemical deposition/stripping of zinc in this ionic liquid polymer gel electrolyte is of interest for rechargeable zinc-based batteries.     

Structural,thermal, and impedance properties of a gel polymer electrolyte containing ionic liquid

The gel polymer electrolytes composed of ionic liquid, 1‐butyl‐3‐methylimidazolium tetrafluoroborate (BMImBF₄) and the copolymer of acrylonitrile (AN), methyl methacrylate (MMA), poly(ethylene glycol) methyl ether methacrylate (PEGMEMA) are synthesized and characterized by FT‐IR spectra, TGA, DSC, and AC impedance measurements. IR spectra show that there is an interaction between PEO side chains of the copolymer and imidazolium cations. TGA measurements indicate that the gel polymer electrolytes are stable until 120°C. By using the equivalent circuit proposed, the experimental data and the simulated data fit very well. The bulk resistance R_b is found to decrease with the increase in BMImBF₄ content. Copyright © 2009 John Wiley & Sons, Ltd.     

Supercapacitor based on graphene and ionic liquid electrolyte

A new kind of supercapacitor by using chemical reduced graphene (CRG) as electrode material and ionic liquid with addition of acetonitrile as electrolyte is assembled and investigated. CRG materials with high surface area are prepared by chemical reduction of graphene oxide. The capacitive properties of the supercapacitor composed of the CRG and ionic liquid electrolyte are studied by electrical impedance spectroscopy, cyclic voltammetry and galvanostatic charge–discharge. With the combined advantages of graphene and ionic liquid, the supercapacitor shows perfect performance. The supercapacitor possesses wide cell voltage and good stability. The specific capacitance, energy density, and specific power density of the present supercapacitor are 132 Fg⁻¹, 143.7 Wh kg⁻¹, and 2.8 kW kg⁻¹, respectively. The results demonstrate the potential application of electrical energy storage devices with high performance based on this new kind of supercapacitor.

     

Supercapacitor based on graphene and ionic liquid electrolyte

A new kind of supercapacitor by using chemical reduced graphene (CRG) as electrode material and ionic liquid with addition of acetonitrile as electrolyte is assembled and investigated. CRG materials with high surface area are prepared by chemical reduction of graphene oxide. The capacitive properties of the supercapacitor composed of the CRG and ionic liquid electrolyte are studied by electrical impedance spectroscopy, cyclic voltammetry and galvanostatic charge–discharge. With the combined advantages of graphene and ionic liquid, the supercapacitor shows perfect performance. The supercapacitor possesses wide cell voltage and good stability. The specific capacitance, energy density, and specific power density of the present supercapacitor are 132?Fg^??, 143.7?Wh?kg^??, and 2.8?kW?kg^??, respectively. The results demonstrate the potential application of electrical energy storage devices with high performance based on this new kind of supercapacitor.     

A disiloxane-functionalized phosphonium-based ionic liquid as electrolyte for lithium-ion batteries

A disiloxane-functionalized ionic liquid based on a phosphonium cation and a bis(trifluoromethylsulfonyl)imide (TFSI) anion was synthesized and characterized. This new ionic liquid electrolyte showed good stability with a lithium transition metal oxide cathode and a graphite anode in lithium ion cells.     

Capacity of graphene anode in ionic liquid electrolyte

The graphene anode was investigated in an ionic liquid electrolyte (0.7 M lithium bis(trifluoromethanesulfonyl)imide (LiNTf₂)) in room temperature ionic liquid (N-methyl-N-propylpyrrolidinium bis(trifluoromethanesulfonyl)imide (MPPyrNTf₂)). SEM and TEM images suggested that the electrochemical intercalation/deintercalation process in the ionic liquid electrolyte without vinylene carbonate (VC) leads to small changes on the surface of graphene particles. However, a similar process in the presence of VC results in the formation of a coating (SEI—solid electrolyte interface) on the graphene surface. During charging/discharging tests, the graphene electrode working together with the 0.7 M LiNTf₂ in MPPyrNTf₂ electrolyte lost its capacity, during cycling and stabilizes at ca. 200 mAh g^?1 after 20 cycles. The addition of VC to the electrolyte (0.7 M LiNTf₂ in MPPyrNTf₂?+?10 wt.% VC) considerably increases the anode capacity. Electrodes were tested at different current regimes: ranging between 50 and 1,000 mA g^?1. The capacity of the anode, working at a low current regime of 50 mA g^?1, was ca. 1,250 mAh g^?1, while the current of 500 mA g^?1 resulted in capacity of 350 mAh g^?1. Coulombic efficiency was stable and close to 95 % during ca. 250 cycles. The exchange current density, obtained from impedance spectroscopy, was 1.3?×?10^?7 A cm^?2 (at 298 K). The effect of the anode capacity decrease with increasing current rate was interpreted as the result of kinetic limits of the electrode operation.     

新型质子离子液体/硅凝胶电解质的制备及其性能

采用一步溶胶-凝胶法首次将质子型离子液体固定于纳米多孔硅骨架中,合成了表面光滑、柔软、透明的质子增强型固态复合凝胶电解质.研究表明,该凝胶电解质结合了无机硅骨架和质子离子液体的双重优点,具有高的热稳定性（〉300℃）、宽的电化学稳定窗口（〉2.8V）和优异的中低温导电性（11.25×10？3Scm？1,80℃）.可望作为一种新型固态电解质应用于先进储能器件.     

A supercooled imidazolium iodide ionic liquid as a low-viscosity electrolyte for dye-sensitized solar cells

A series of allyl-functionalized imidazolium salts are reported, including 1-allyl-3-ethylimidazolium iodide and 1-allyl-3-propylimidazolium iodide, which have melting points close to room temperature and show typical properties of supercooled fluids if heated above their melting points. Their viscosities in the liquid state are considerably lower than the benchmark ionic liquid used in solar cells, viz., 1-propyl-3-methylimidazolium iodide. Electrolytes containing these new liquids provide excellent efficiencies and good stability in dye-sensitized solar cells when subjected to an accelerated-light soaking test at 60 degrees C. The structures of three of the new salts have been established in the solid state by single-crystal X-ray analysis.     

Nano-biphasic ionic liquid systems composed of hydrophobic phosphonium salts and a hydrophilic ammonium salt

A combination of a phosphonium-type-zwitterions-lithium bis(trifluoromethanesulfonyl)imide complex and a hydrophilic ammonium salt provides a nanosegregated liquid-crystalline matrix consisting of hydrophilic ionic liquid (IL) domains and hydrophobic IL domains.     

Self-assembly of a nonionic surfactant at the graphite/ionic liquid interface

In this study, we demonstrate by AFM imaging that nonionic surfactants self-assemble into hemicylindrical aggregates at the interface between graphite and the room temperature ionic liquid ethylammonium nitrate. Like aqueous systems, surfactant first adsorbs in a tail-to-tail monolayer arrangement along one of the three symmetry axes of graphite, templating subsequent self-assembly into adsorbed hemicylinders. Longer surfactant tails and higher concentrations are required to produce hemicylindrical aggregates in the ionic liquid than in aqueous solutions.     

A sulfide/polysulfide-based ionic liquid electrolyte for quantum dot-sensitized solar cells

Further development of quantum dot-sensitized solar cells (QDSCs) will require long-term stability in addition to the continuous increase of photovoltaic (PV) conversion efficiency achieved in the last years. We report a robust S(2-)/S(n)(2-) electrolyte that has been specifically designed for compatibility with CdSe quantum dots in sensitized solar cells. The new pyrrolidinium ionic liquid reaches 1.86% efficiency and a short-circuit current close to 14 mA·cm(-2) under air-mass 1.5 global illumination and improves the device lifetime with good photoanode stability over 240 h. PV characterization showed that the solar cell limitations relate to poor catalysis of regeneration at the counter electrode and high recombination. Further improvement of these factors in the robust electrolyte configuration may thus have a significant impact for advancing the state-of-the-art in QDSCs.     

Dielectric spectroscopy study on ionic liquid microemulsion composed of water, TX-100, and BmimPF6

We report here a broadband dielectric spectroscopy study on an ionic liquid microemulsion (ILM) composed of water, Triton X-100 (TX-100), and 1-butyl-3-methylimidazolium hexafluorophosphate (bmimPF(6)). It is found that the phase behavior of this ILM can be easily identified by its dielectric response. The dielectric behavior of the ILM in the GHz range is consistent with that of TX-100∕water mixtures with comparable water-to-TX-100 weight ratio. It consists of the relaxations due to ethylene oxide (EO) unit relaxation, hydration water dynamics, and∕or free water dynamics. The water content dependence of the EO unit relaxation suggests that this relaxation involves dynamics of hydration water molecules. In the IL-in-water microemulsion phase, it is found that bmimPF(6) molecules are preferentially dissolved in water when their concentration in water is lower than the solubility. An additional dielectric relaxation that is absent in the TX-100∕water mixtures is observed in the frequency range of 10(7)-10(8) Hz for this ILM. This low-frequency relaxation is found closely related to the bmimPF(6) molecule and could be attributed to the hopping of its cations∕anions between the anionic∕cationic sites.     

Electrical,optical and photoelectrochemical studies on a solid PEO-polymer electrolyte doped with low viscosity ionic liquid

Solid polymer electrolyte (PEO:KI:I₂) membranes doped with low viscosity (34 cP at 25 °C) ionic liquid EMImTFSI (1-ethyl 3-methylimidazolium bis(trifluoromethylsulfonyl)imide) showing plasticizing effect as well as improved dye sensitized solar cell efficiency have been reported first time. Apart from ionic conductivity enhancement due to large number of free charge carriers provided by ionic liquid (IL) it assist in reducing cystallinity of polymer electrolyte matrix which was confirmed by polarized optical microscopy (POM). Cyclic voltammetry was carried out to study the reactions of iodide, iodine and IL in polymer electrolyte matrix.     

Direct electrodeposition of FeCoZn wire arrays from a zinc chloride-based ionic liquid

The use of Zinc chloride-1-ethyl-3-methylimidazolium chloride ionic liquid enables facile template-free electrochemical fabrication of arrays of polycrystalline ternary FeCoZn nanowires with diameter of 100–200 nm by controlling the deposition potential. The nanowire arrays were characterized by scanning electron microscopy, powder X-ray diffraction and transmission electron microscopy.     

A polymer electrolyte containing ionic liquid for possible applications in photoelectrochemical solar cells

Various iodide ion conducting polymer electrolytes have been studied as candidate materials for fabricating photoelectrochemical (PEC) solar cells and energy storage devices. In this study, enhanced ionic conductivity values were obtained for the ionic liquid tetrahexylammonium iodide containing polyethylene oxide (PEO)-based plasticized electrolytes. The analysis of thermal properties revealed the existence of two phases in the electrolyte, and the conductivity measurements showed a marked conductivity enhancement during the melting of the plasticizer-rich phase of the electrolyte. Annealed electrolyte samples showed better conductivity than nonannealed samples, revealing the existence of hysteresis. The optimum conductivity was shown for the electrolytes with PEO:salt = 100:15 mass ratio, and this sample exhibited the minimum glass transition temperature of 72.2 °C. For this optimum PEO to salt ratio, the conductivity of nonannealed electrolyte was 4.4 × 10⁻⁴ S cm⁻¹ and that of the annealed sample was 4.6 × 10⁻⁴ S cm⁻¹ at 30 °C. An all solid PEC solar cell was fabricated using this annealed electrolyte. The short circuit current density (I _SC), the open circuit voltage (V _OC), and the power conversion efficiency of the cell are 0.63 mA cm⁻², 0.76 V, and 0.47% under the irradiation of 600 W m⁻² light.     

Observation of a chevron hybrid structure in the smectic A phase of a liquid crystal device

Small angle X-ray diffraction experiments show the emergence of a chevron structure on cooling from the nematic phase into the smectic A phase of the commercial mixture S3 (Merck Ltd, UK), in a display device. The chevron angle increases from 0 at the nematicsmectic transition temperature, T NS, to a maximum value of 8.5 , which is reached when the sample is 15 C below T NS. Between 5 C and 15 C below the transition temperature a quasi bookshelf structure emerges, in addition to the prevailing chevron structure; such a structure has not been hitherto reported. There is no further resolvable change in the device structure on cooling lower than T NS -15 C. The chevron structure is due to the combination of layer thinning and fixed surface layers, as confirmed by a comparison of layer spacing calculated from the Bragg angle equation and from the layer thinning equation ( d = d nematic cos delta, where delta is the chevron angle).