Lithium Polystyrene Sulfonate as a Hole Transport Material in Inverted Perovskite Solar Cells

Despite the exceptional efficiency of perovskite solar cells (PSCs), further improvements can be made to bring their power conversion efficiencies (PCE) closer to the Shockley-Queisser limit, while the development of cost-effective strategies to produce high-performance devices are needed for them to reach their potential as a widespread energy source. In this context, there is a need to improve existing charge transport layers (CTLs) or introduce new CTLs. In this contribution, we introduced a new polyelectrolyte (lithium poly(styrene sulfonate (PSS))) (Li:PSS) polyelectrolyte as an HTL in inverted PSCs, where Li⁺ can act as a counter ion for the PSS backbone. The negative charge on the PSS backbone can stabilize the presence of p-type carriers and p-doping at the anode. Simple Li:PSS performed poorly due to poor surface coverage and voids existence in perovskite film as well as low conductivity. PEDOT:PSS was added to increase the conductivity to the simple Li:PSS solution before its use which also resulted in lower performance. Furthermore, a bilayer of PEDOT:PSS and Li:PSS was employed, which outperformed simple PEDOT:PSS due to high quality of perovskite film with large grain size also the large electron injection barrier (ϕ_e) impeded back diffusion of electrons towards anode. As a consequence, devices employing PEDOT:PSS / Li:PSS bilayers gave the highest PCE of 18.64%.     

Water soluble amino grafted silicon nanoparticles and their use in polymer solar cells

Stable aqueous amino-grafted silicon nanoparticles(SiNPs-NH2) were prepared via one-pot solution method. By grafting amino groups on the particle surface, the dispersion of SiNPs in water became very stable and clear aqueous solutions could be obtained. By incorporating SiNPs-NH2 into the hole transport layer of poly(3,4-ethylenedioxythiophene)/polystyrene sulfonic acid(PEDOT:PSS), the performance of polymer solar cells composed of poly[2-methoxy,5-(2'-ethylhexyloxy)-1,4-phenylene vinylene](MEH-PPV):[6,6]-phenyl-C61-butyric acid methyl ester(PCBM) as active layer can be improved. SiNPs-NH2 are dispersed uniformly in the PEDOT:PSS solution and help form morphologies with small-sized domains in the PEDOT:PSS film. SiNPs-NH2 serve as screens between conducting polymer PEDOT and ionomer PSS to improve the phase separation and charge transport of the hole transport layer. As a result, the sheet resistance of PEDOT:PSS thin films is decreased from(93 ± 5) × 105 to(13 ± 3) × 105 ?/□. The power conversion efficiency(PCE) of polymer solar cells was thus improved by 9.8% for devices fabricated with PEDOT:PSS containing 1 wt% of SiNPs-NH2, compared with the devices fabricated by original PEDOT:PSS.     

Ti3C2Tx-Modified PEDOT:PSS Hole-Transport Layer for Inverted Perovskite Solar Cells

PEDOT:PSS is a commonly used hole-transport layer (HTL) in inverted perovskite solar cells (PSCs) due to its compatibility with low-temperature solution processing. However, it possesses lower conductivity than other conductive polymers and metal oxides, along with surface defects, limiting its photovoltaic performance. In this study, we introduced two-dimensional Ti₃C₂T_x (MXene) as an additive in the PEDOT:PSS HTL with varying doping concentrations (i.e., 0, 0.03, 0.05, and 0.1 wt.%) to tune the electrical conductivity of PEDOT:PSS and to modify the properties of the perovskite film atop it. We noted that the grain size of the CH₃NH₃PbI₃ (MAPI₃) perovskite layer grown over an optimal concentration of MXene (0.03 wt.%)-doped PEDOT:PSS increased from 250 nm to 400 nm, reducing charge recombination due to fewer grain boundaries. Ultraviolet photoelectron spectroscopy (UPS) revealed increased work function (WF) from 4.43 eV to 4.99 eV with 0.03 wt.% MXene doping, making the extraction of holes easier due to a more favorable energy level alignment with the perovskite. Quantum chemical investigations based on density functional theory (DFT) were conducted at the ωB97XD/6-311++G(d,p) level of theory to provide more insight into the stability, bonding nature, and optoelectronic properties of the PEDOT:PSS–MXene system. The theoretical investigations revealed that the doping of PEDOT:PSS with Ti₃C₂T_x could cause a significant effect on the electronic properties of the HTL, as experimentally demonstrated by an increase in the electrical conductivity. Finally, the inverted PSCs employing 0.03 wt.% MXene-doped PEDOT:PSS showed an average power conversion efficiency (PCE) of 15.1%, up from 12.5% for a reference PSC employing a pristine PEDOT:PSS HTL. The champion device with a 0.03 wt.% MXene–PEDOT:PSS HTL achieved 15.5% PCE.     

Conductivity enhancement of PEDOT:PSS film via sulfonic acid modification: application as transparent electrode for ITO-free polymer solar cells

3-Hydroxy-1-propanesulfonic acid(HPSA)was applied as a modification layer on poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate)(PEDOT:PSS)film via spin-coating,resulting in a massive boost of the conductivity of PEDOT:PSS film,and thus the as-formed PEDOT:PSS/HPSA bilayer film was successfully used as a transparent electrode for ITO-free polymer solar cells(PSCs).Under the optimized concentration of HPSA(0.2 mol L~(-1)),the PEDOT:PSS/HPSA bilayer film has a conductivity of 1020 S cm~(-1),which is improved by about 1400 times of the pristine PEDOT:PSS film(0.7 S cm~(-1)).The sheet resistance of the PEDOT:PSS/HPSA bilayer film was 98Ωsq~(-1),and its transparency in the visible range was over 80%.Both parameters are comparable to those of ITO,enabling its suitability as the transparent electrode.According to atomic force microscopy(AFM),UV-Vis and Raman spectroscopic measurements,the conductivity enhancement was resulted from the removal of PSS moiety by methanol solvent and HPSA-induced segregation of insulating PSS chains along with the conformation transition of the conductive PEDOT chains within PEDOT:PSS.Upon applying PEDOT:PSS/HPSA bilayer film as the transparent electrode substituting ITO,the ITO-free polymer solar cells(PSCs)based on poly[N-9″-hepta-decanyl-2,7-carbazole-alt-5,5-(4′,7′-di-2-thienyl-2′,1′,3′-benzothiadiazole)]:[6,6]-phenyl C71-butyric acid methyl ester(PC_(71)BM)(PCDTBT:PC_(71)BM)active layer exhibited a power conversion efficiency(PCE)of 5.52%,which is comparable to that of the traditional ITO-based devices.     

Controllable Optical,Electrical, and Morphologic Properties of 3,4‐Ethylenedioxythiophene Based Electrocopolymerization Films

This contribution presents a kind of novel and neutral network films based on EDOT formed by in situ electrocopolymerization (ECP). The ECP films which are neutral and colorless exhibit the conductivity of 0.2–0.5 S · cm⁻¹, W_F of 4.79–5.20 eV, and RMS roughness of 3.51–5.26 nm. The electroluminescent devices where ECP films acted as hole‐transport layer (HTL) exhibit higher brightness, current density, efficiency (20–30% improvement), and stability than that of PEDOT:PSS HTL device. The ECP films also significantly benefit the stability of neighboring organic layer compared to PEDOT:PSS. This kind of new ECP films affords more opportunities to develop organic light‐emitting diodes (OLEDs) with high performances and stability.

     

Highly enhanced thermoelectric performance of WS2 nanosheets upon embedding PEDOT:PSS

Two‐dimensional (2D) WS₂ nanosheets (NSs) as a promising thermoelectric (TE) material have gained great concern recently. The low electrical conductivity significantly limits its further development. Herein, we reported an effective method to enhance the TE performance of WS₂ NSs by combining poly(3,4‐ethylenedioxythiophene):poly(4‐styrenesulfonate) (PEDOT:PSS). The restacked WS₂ NSs thin film with 1T phase structure obtained by a common chemical lithium intercalation show a high Seebeck coefficient of 98 μV K^?1 and a poor electrical conductivity of 12.5 S cm^?1. The introduction of PEDOT:PSS with different contents obviously improve the electrical conductivity of WS₂ NSs thin films. Although a declining Seebeck coefficient was observed, an optimized TE power factor of 45.2 μW m^?1 k^?1 was achieved for WS₂/PEDOT:PSS composite thin film. Moreover, the as‐prepared WS₂/PEDOT:PSS thin film can be easily peeled off and transferred to other substrate leading to a more promising application. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55 , 997–1004     

Nickel(II) Nitrate Hole-Transporting Layers for Single-Junction Bulk Heterojunction Organic Solar Cells with a Record 19.02 % Efficiency

A facile strategy was developed here to improve the film quality of nickel-based hole transporting layer (HTL) for efficient organic solar cell (OSC) applications. To prevent the agglomeration of Ni(NO₃)₂ during film deposition, acetylacetonate was added into the precursor solution, which led to the formation of an amorphous and glass-like state. After thermal annealing (TA) treatment, the film-forming ability could be further improved. The additional UV-ozone (UVO) treatment continuously improved the film quality and increased the work function and conductivity of such HTL. The resulting TA & UVO modified Ni(NO₃)₂ & Hacac HTL produced highly efficient organic solar cells with exciting power conversion efficiencies of 18.42 % and 19.02 % for PM6 : BTP-eC9 and D18 : BTP-Th devices, respectively, much higher than the control PEDOT : PSS devices.     

左旋多巴和N,N-二甲基亚砜共掺杂PEDOT:PSS作为空穴传输层的高性能p-i-n型钙钛矿太阳能电池

在p-i-n型的钙钛矿太阳能电池中,聚3, 4-乙烯二氧噻吩：聚苯乙烯磺酸盐(PEDOT:PSS)作为最常用的空穴传输层(HTL)材料之一,由于其存在着吸湿性强以及能级与钙钛矿层不匹配等缺点,限制了它的应用。基于此,本文拟采用将左旋多巴(DOPA)和N, N-二甲基亚砜(DMSO)共同掺杂于PEDOT:PSS作为HTL的简单方法制备高性能p-i-n型钙钛矿太阳能电池。研究结果表明,DOPA和DMSO共掺杂PEDOT:PSS可以有效的调节HTL的能级并提高其导电性,器件的能量转化效率由13.35%显著提高到了17.54%。进一步研究发现,相比于未掺杂或单一掺杂的PEDOT:PSS,在DOPA和DMSO共掺杂的PEDOT:PSS上更有利于生长大尺寸、高结晶度的钙钛矿晶体;同时稳态/瞬态荧光和交流阻抗测试表明器件的内部载流子分离和传输更加有效。     

Roll‐to‐Roll printed PEDOT/PSS/GO Plastic Film for Electrochemical Determination of Carbofuran

In this work, we developed a roll‐to‐roll printed poly(3,4‐ethylenedioxythiophene)/polystyrene sulphoanate without graphene oxide (GO) (PEDOT/PSS) and with graphene oxide (PEDOT/PSS/GO) plastic films for the electrochemical determination of carbofuran. Both the PEDOT/PSS and PEDOT/PSS/GO plastic films showed electroactivity towards the oxidation of carbofuran. Incorporation of graphene oxide (GO) improves the electrochemical activity of carbofuran and increased its sensitivity. The printed plastic films were characterized by cyclic voltammetry (CV), linear sweep voltammetry (LSV), surface profilometer, four point probe and atomic force microscopy (AFM). The effects of pH, deposition time, deposition potential and film thickness on the oxidation peak current of carbofuran were investigated. Under the optimized conditions, a dynamic linear range of 1 μM–90 μM with a detection limit of 1.0×10^?7 M (S/N=3) were obtained. The printed PEDOT/PSS/GO plastic electrode was applied for the determination of carbofuran in vegetable and fruit samples with recoveries between 94.4 and 101.8 %.     

Inverted Perovskite Solar Cells Based on Small Molecular Hole Transport Material C8‐Dioctylbenzothienobenzothiophene

The small organic molecular Dioctylbenzothienobenzothiophene (C₈‐BTBT) has been explored as hole transport material (HTM) to replace PEDOT:PSS in inverted perovskite solar cells (PVSCs). MAPbI₃ perovskite films depositd onto C₈‐BTBT are smooth and uniform, with negligible residual of PbI₂ and large grain size even larger than 1 μm. Our champion C₈‐BTBT based devices reached a high power conversion efficiency (PCE) of 15.46% with marginal hysteresis, much higher than that of 11.50% achieved using PEDOT:PSS. Besides, devices adopting C₈‐BTBT as substrate show superior stability compared with the PEDOT:PSS based devices when stored under ambient conditions with a relative humidity of (25±5)%.     

Free‐Standing Conducting Polymer Films for High‐Performance Energy Devices

Thick, uniform, easily processed, highly conductive polymer films are desirable as electrodes for solar cells as well as polymer capacitors. Here, a novel scalable strategy is developed to prepare highly conductive thick poly(3,4‐ethylenedioxythiophene):polystyrene sulfonate (HCT‐PEDOT:PSS) films with layered structure that display a conductivity of 1400 S cm^?1 and a low sheet resistance of 0.59 ohm sq^?1. Organic solar cells with laminated HCT‐PEDOT:PSS exhibit a performance comparable to the reference devices with vacuum‐deposited Ag top electrodes. More importantly, the HCT‐PEDOT:PSS film delivers a specific capacitance of 120 F g^?1 at a current density of 0.4 A g^?1. All‐solid‐state flexible symmetric supercapacitors with the HCT‐PEDOT:PSS films display a high volumetric energy density of 6.80 mWh cm^?3 at a power density of 100 mW cm^?3 and 3.15 mWh cm^?3 at a very high power density of 16160 mW cm^?3 that outperforms previous reported solid‐state supercapacitors based on PEDOT materials.     

氧化石墨烯掺杂PEDOT:PSS作为空穴注入层对有机发光二极管发光性能的影响

研究了氧化石墨烯(GO)掺杂聚(3,4-亚乙二氧基噻吩):聚(苯乙烯磺酸) (PEDOT:PSS)作为空穴注入层对有机发光二极管发光性能的影响. 在PEDOT:PSS水溶液中掺入GO, 经过湿法旋涂和退火成膜后, 不仅提高了空穴注入层的空穴注入能力和导电率, 透光率也得到了相应的提高, 从而使得有机发光二极管(OLED)器件的发光性能得到了提升. 通过优化GO掺杂量发现, 当GO掺杂量为0.8%(质量分数)时, 空穴注入层的透光率达到最大值(96.8%), 此时获得的OLED器件性能最佳, 其最大发光亮度和最大发光效率分别达到17939 cd·m^-2和3.74 cd·A^-1. 与PEDOT:PSS 作为空穴注入层的器件相比, 掺杂GO后器件的最大发光亮度和最大发光效率分别提高了46.6%和67.6%.     

Aqueous solution-processed NiOx anode buffer layers applicable for polymer solar cells

A green and facile method has been developed for the room temperature and aqueous solution preparation of NiO_x film as anode buffer layers for polymer solar cells (PSCs). The NiO_x buffer layer is prepared simply by spin-coating nickel acetylacetonate precursor-based aqueous solution onto ITO substrate at room temperature in air. UV-ozone post-treatment promotes the formation of dipolar NiOOH species on the film surface, resulting in the anode buffer layer with suitable work function. PSCs have been fabricated with the device structure of ITO/NiO_x/photoactive layer/PFN/Al. The power conversion efficiencies of the PSCs based on PTB7:PC₇₁BM blends (8.43%) and P3HT:PC₇₁BM blends (3.04%) with NiO_x anode buffer layer are comparable to those with the commonly used PEDOT:PSS anode buffer layer. In addition, the devices made with NiO_x buffer layer exhibit much better air stability than those with PEDOT:PSS. These results indicate that the water solution processed NiO_x film at room temperature in air is a promising anode buffer layer for efficient and stable PSCs. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 747–753     

Effect of H2SO4 Solution Treatment on Adhesion,Charge Transfer,and Catalytic Performance of Screen-Printed PEDOT:PSS

Post-treatment was performed for poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) films screen-printed on fluorine-doped tin oxide (FTO) substrates, to improve their charge transfer efficiency. Different H₂SO₄ solutions, including concentrated H₂SO₄ and H₂SO₄ diluted with H₂O or dimethyl sulfoxide (DMSO), were adopted during the post-treatment. The adhesion of the as-treated films was evaluated by adhesive tape peeling tests, the surface morphology and vertical charge transfer from the films to the substrates were investigated by current-sensing atomic force microscopy, and the catalytic activities toward I₃⁻ reduction of PEDOT:PSS films were characterized by electrochemical measurements. It is discovered that selecting proper H₂SO₄ solutions is crucial to improve the charge transfer efficiency and catalytic performance while maintaining reliable adhesion of the film on the substrates, with H₂SO₄/DMSO performing best as the solution for post-treatment. A mechanistic explanationis proposed based on different interactions among solution, PEDOT:PSS, and the substrate for various post-treatment solutions.     

Enzymatic‐catalyzed polymerization of water‐soluble electrically conductive polymer PEDOT:PSS

Water‐soluble electrically conductive polymer poly(3,4‐ethylenedioxythiophene) (PEDOT) was synthesized by the enzymatic‐catalyzed method using 3,4‐ethylenedioxythiophene (EDOT) as monomer, poly(styrenesulfonate) (PSS) as water‐soluble polyelectrolyte, horseradish peroxidase enzyme as catalyst, and hydrogen peroxide (H₂O₂) as oxidant. Fourier transform infrared spectra and UV–vis absorption spectra confirm the successful enzymatic‐catalyzed polymerization of PEDOT. Dynamic light scattering data confirm the formation of a stable PEDOT:PSS aqueous dispersion. The thermo gravimetric data show that the obtained PEDOT is stable over a fairly high range of temperatures. The atomic force microscopy height images show that the PEDOT:PSS aqueous dispersion can form excellent homogeneous and smooth films on various substrates by conventional solution processing techniques, which renders this PEDOT:PSS aqueous dispersion a very promising candidate for various application in electronic devices. This enzymatic polymerization is a new approach for the synthesis of optical and electrical active PEDOT polymer, which benefits simple setting, high yields, and environmental friendly route. Copyright © 2014 John Wiley & Sons, Ltd.     

Sticky interconnect for solution-processed tandem solar cells

Graphene oxide (GO) can be viewed as a two-dimensional, random diblock copolymer with distributed nanosize graphitic patches and highly oxidized domains, thus capable of guiding the assembly of other materials through both π-π stacking and hydrogen bonding. Upon mixing GO and conducting polymer poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) in water, a dispersion with dramatically increased viscosity is obtained, which turns into sticky thin films upon casting. Surprisingly, the insulating GO makes PEDOT much more conductive by altering its chain conformation and morphology. The GO/PEDOT gel can function as a metal-free solder for creating mechanical and electrical connections in organic optoelectronic devices. As a proof-of-concept, polymer tandem solar cells have been fabricated by a direct adhesive lamination process enabled by the sticky GO/PEDOT film. The sticky interconnect can greatly simplify the fabrication of organic tandem architectures, which has been quite challenging via solution processing. Thus, it could facilitate the construction of high-efficiency tandem solar cells with different combinations of solution-processable materials.     

Bis(4-methylthio)phenyl)amine-based hole transport materials for highly-efficient perovskite solar cells: insight into the carrier ultrafast dynamics and interfacial transport

Hole transport layers(HTLs) play a significant role in the performance of perovskite solar cells. A new class of linear smallmolecules based on bis(4-methylthio)phenyl)amine as an end group, carbon, oxygen and sulfur as the center atoms for the center unit(denoted as MT-based small-molecule), respectively, have been applied as HTL, and two of them presented the efficiency over 20% in the planar inverted perovskite solar cells(PSCs), which demonstrated a significant improvement in comparison with the widely used HTL, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate)(known as PEDOT:PSS), in the planar inverted architecture. The ultrafast carrier dynamics show that the excited hot carrier cooling process of MT-based small-molecule HTL samples is faster than that of PEDOT:PSS samples. The kinetic analysis of photo-bleaching peaks of femtosecond transient absorption spectra reveals that the traps at the interface between MT-based small-molecule HTLs and MAPbI_3 can be filled much quicker than that at PEDOT/MAPbI_3 interfaces. Moreover, the hole injection time from MAPbI_3 to MT-based small-molecule HTLs is around 10 times quicker than that to PEDOT:PSS. Such quick trap filling and hole extraction bring a significant enhancement in photovoltaic performances. These findings uncover the carrier transport mechanisms and illuminate a promising approach for the design of new HTLs for highly-efficient perovskite solar cells.     

Effects of Supporting Electrolytes on Spectroelectrochemical and Electrochromic Properties of Polyaniline‐poly(styrene sulfonic acid) and Poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid)‐based Electrochromic Device

Electrochromic devices are fabricated by using polyaniline (PANI) doped with poly(styrene sulfonic acid) (PSS) as coloring electrodes, poly(ethylenedioxythiophene)‐poly(styrene sulfonic acid) (PEDOT‐PSS) as complementary electrodes, and hybrid polymer electrolytes as gel electrolytes. The device based on LiClO₄‐based electrolyte (weight ratio of PMMA:PC:LiClO₄ = 0.7:1.1:0.3) shows the highest optical contrast and coloration efficiency (333 cm²/C) after 1200 cycles in these devices, and the color changes from pale yellow (?0.5 V) to dark blue (+2.5 V). The spectroelectrochemical and electrochromic switching properties of electrochromic devices are investigated, the maximum optical contrast (ΔT%) of electrochromic device for ITO|PANI‐PSS‖PMMA‐PC‐LiClO₄‐SiO₂‖PEDOT‐PSS|ITO are 31.5% at 640 nm, and electrochromic device based on LiClO₄‐based electrolyte with SiO₂ shows faster response time than that based on LiClO₄‐based electrolyte without SiO₂.     

Co-La-Based Hole-Transporting Layers for Binary Organic Solar Cells with 18.82 % Efficiency

Poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) is a widely used hole transporting layer (HTL) in organic solar cells (OSCs), but its acidity severely reduces the stability of devices. Until now, very few HTLs were developed to replace PEDOT:PSS toward stable and high-performance OSCs. Herein, a new cobalt-lanthanum (Co-La) inorganic system was reported as HTL to show a high conversion efficiency (PCE) of 18.82 %, which is among the top PCEs in binary OSCs. Since electron-rich outer shell of La atom can interact with Co atom to form charge transfer complex, the work function and conductivity of the Co-La system could be simultaneously enhanced compared to Co or La-based HTLs. This Co-La system could also be applied into other OSCs to show high performance. All these results demonstrate that binary Co-La systems as HTL can efficiently tackle the issue in hole transporting and show powerful application in OSCs to replace PEDOT:PSS.     

Paper: An effective substrate for the enhancement of thermoelectric properties in PEDOT:PSS

A novel strategy via paper as an effective substrate has been introduced as a thermoelectric material in this work. Free‐standing poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS)/paper composite films are conveniently prepared by a one‐step method of directly writing PEDOT:PSS solution on paper, making the process simple, rapid, and facile. The free‐standing composite films display excellent flexibility, light weight, soaking stability in water, and great potential in large‐scale production. Improved thermoelectric properties are obtained in PEDOT:PSS/paper composite films, owing to the simultaneously enhanced Seebeck coefficient (30.6 μV K^?1) and electrical conductivity, and a low thermal conductivity (0.16 W m^?1 K^?1) compared with pristine PEDOT:PSS films. The results indicate that paper as an effective substrate is suitable for the preparation of high‐performance and flexible thermoelectric materials. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2014 , 52, 737–742