Impact of electron irradiation on particle track etching response in polyallyl diglycol carbonate (PADC)

In the present work, attempts have been made to investigate the modification in particle track etching response of polyallyl diglycol carbonate (PADC) due to impact of 2 MeV electrons. PADC samples pre-irradiated to 1, 10, 20, 40, 60, 80 and 100 Mrad doses of 2 MeV electrons were further exposed to 140 MeV²⁸ Si beam and dose-dependent track registration properties of PADC have been studied. Etch-rate values of the PADC irradiated to 100 Mrad dose electron was found to increase by nearly 4 times that of pristine PADC. The electron irradiation has promoted chain scissioning in PADC, thereby converting the polymer into an easily etchable polymer. Moreover, the etching response and the detection efficiency were found to improve by electron irradiation. Scanning electron microscopy of etched samples further revealed the surface damage in these irradiated PADCs.     

Gamma effect on track properties of PADC detector

Effect of high gamma irradiation on track properties of PADC (Homalite) has been studied in the dose range of 10¹–10⁶ Gy. The properties like bulk-etch rates and track-etch rates of the detector are found to increase due to gamma exposure. Etching efficiency of the detector increases due to exposure and it is significant at the dose higher than 10³ Gy. Another track property, the critical angle, is also influenced by gamma exposure and is found to decrease with increasing dose. In all cases it is observed that the post-gamma exposure has greater effect than the pre-gamma exposure. The experimental results are presented and discussed in details.     

On the mechanism of the sensitization of PADC (poly(allyl diglycol carbonate)) track detectors by carbon dioxide treatment

The sensitization effect of carbon dioxide treatments with 0.6 MPa on poly(allyl diglycol carbonate) (PADC) etched track detectors is confirmed for protons and He, C, and Fe ions, where the stopping powers range from 10 to 600 keV/μm. Based on the FT-IR study for the PADC films that were maintained at room temperature and at elevated temperatures, the diffusion coefficient of carbon dioxide, is determined as D = 14,670exp(−9030/T(K)) cm²/s. The sensitivity is enhanced when carbon dioxide is released toward the chemical etching solution that passes through the detector surface. Segmented PADC polymer chains are washed away by the flow of carbon dioxide along the latent tracks in PADC, which results in a higher track etch rate.     

Response of Makrofol polycarbonate plastic track detector to 1.1 MeV/N 54 132 Xe-ion

Makrofol polycarbonate plastic track detectors have been exposed to ₅₄ ¹³² Xe -ions of energy 1.1 MeV/N from the cyclotron beam. The bulk etch rate and track etch rate are measured for different temperatures and the activation energies are calculated. The maximum etched track length is compared with the theoretically computed range. The critical energy loss is (dE/dx) _c =5 MeV cm² mg⁻¹ for this detector material.     

用20—1020 keV单能质子刻度CR-39固体核径迹探测器

用北京师范大学2×1.7MV串列加速器和400 kV高压倍加器产生的20—1020 keV单能质子束对CR-39固体核径迹探测器进行了刻度.为了保证质子的单能性和固体核径迹探测器上径迹密度不能超过10⁶/cm²的要求,对两台加速器分别采用了不同方法控制质子辐照数量.在串列加速器上采用了狭缝加转盘的方法,在高压倍加器上采用了100 ns单次高压脉冲扫描束流的方法,既保持了质子的单色性,又达到了质子注量小于10⁶/cm²的 关键词： 单能质子 固体核径迹探测器 CR-39     

Radiation chemical yields for the losses of typical functional groups in PADC films for high energy protons registered as unetchable tracks

A series of FT-IR spectrometric studies has been performed to understand the latent track structure in poly(allyl diglycol carbonate), PADC, which were exposed to proton beams with energies of 20, 30 and 70 MeV. These energies are too high to register etchable tracks in PADC. Chemical damage parameters, such as damage density, effective track core radius and radiation chemical yields, for losses of ether bond, carbonate ester bond and CH groups in PADC are evaluated as a function of the stopping power, which were compared to the previous results for 5.7 MeV proton and heavy ions, between He and Xe. Graphs of the chemical damage parameters are given at the wide stopping powers ranging from 1 to 12,000 keV/μm. The decreasing behaviors of the ether and carbonate ester bonds are on the almost identical trends with those of the heavy ions. On the contrary to this, the reducing behavior of CH groups is similar to that of the gamma rays. Different dependence of the chemical damage parameters for the loss of CH groups is found on the stopping powers between the both sides of the detection threshold as an etched track detector.     

On alpha particle spectroscopy based on the over-etched track length in PADC (CR-39 detector)

In the current work, alpha particle spectroscopy is investigated experimentally by utilizing the over-etched track lengths in the CR-39 detector. CR-39 samples were exposed perpendicularly to alpha particles emitted from ²⁴¹Am with an energy ranging from 0.5 to 5.5 MeV. CR-39 samples were etched in 6.25 N NaOH at (70±0.5)°C for different durations. The track diameter and track length were measured under an optical microscope. The results show that, the energy-over-etched track length calibration curve is monotonic, in other words, the over-etched track length is a monotonic function in alpha particle energy. On the other hand, the energy-diameter calibration curve is degenerated, i.e. alpha track diameter is non-monotonic function in alpha particle energy. These results suggest that the CR-39 detector could be used as a wide range alpha particles spectrometer using an energy-over-etched track length calibration curve.     

强激光-固体靶相互作用中高能质子的研究进展

本文介绍了强激光与固体靶相互作用产生高能质子研究中的一些重要物理问题和目前面临的挑战.回顾了强激光与固体靶相互作用中高能质子研究的历史和发展状况;简要叙述了国内外关于高能质子研究的最新进展;总结、评述了高能质子研究过程中关于高能质子的起源和加速机制等问题存在的争议以及需要进一步研究的相关问题.     

On the response of LR-115 plastic track detector to 10 20 Ne-ion

The track etch rates of ₁₀ ²⁰ Ne-ion in cellulose nitrate (LR-115) have been measured for different temperatures and the activation energy is determined. The experimental results show that both the track etch rate and the normalized track etch rate depend on the energy loss as well as on etching temperature. The maximum etched track length of ₁₀ ²⁰ Ne-ion agrees with the theoretically computed range. The experimental results show that there is no sharp threshold, at least in CN(LR-115).     

Latent track structure in polymers as observed by a highly sensitive electrolytical conductivity measurement

Abstract

First results of a new electrolytical conductivity cell are reported concerning the initial stage of the pore opening process during track etching in vitreous solids. On the basis of the soft mode (low-energy excitation) model for track etching, a distribution function for the number of perforated micropores as function of time is calculated by accounting for the radial etch rate as function of the effective pore radius.     

Calculations of track parameters and plots of track openings and wall profiles in CR39 detector

Computer programs have been developed to calculate track parameters and to plot track openings and wall profiles. The programs are based on equations derived for three-dimensional consideration of track development. All possible cases of track openings and wall profiles are obtainable from these equations. Results are given for lengths of major and minor axes, track depths and surface areas of track openings. Some examples of track openings and wall profiles are also presented.     

Comparison of responses of CR-39, PM-355, and CN track detectors to energetic hydrogen-, helium-, nitrogen-, and oxygen-ions

Samples made of the CR-39 and PM-355 plastic nuclear track detectors (NTDs) as well as of the CN films were irradiated with quasi-monoenergetic beams of protons, alphas, N⁺-, and O⁺-ions produced by various accelerators. For different samples an energy value of the particle beams was changed from several hundreds keV to 3 or 4.5 MeV. After irradiation the detector samples were etched chemically under controlled conditions during periods lasting from 2 hrs to 20 hrs. Every 2 hrs track diameters were measured by means of an optical microscope. Differences in the crater diameters in the detectors etched in steps, and those etched continously, have been found to be smaller than 10 percent. The paper results detailed calibration diagrams showing a dependence of track diameters on the ion energy value for different etching times.     

Post-irradiation sensitization of CR-39 track detector in carbon dioxide atmosphere

The effect of post-irradiation treatment of CR-39 track detector in carbon dioxide atmosphere on the alpha particle registration sensitivity was investigated. Significant increase in etch rate ratio for 6.1 MeV ²⁵²Cf alpha particle was observed. The sensitization increasedboth as a function of trating time and as a function of carbon dioxide pressure in the treating vessel. Energy dependence of the sensitization was found to be small in the 2–9 MeV alpha particle energy interval. Fading of latent tracks after the sensitization process was slow in a one day period. Pre-irradiation treatment in carbon dioxide showed also some sensitization, though to a lesser extent than post-irradiation treatment. However, exposing CR-39 alpha particles in pure carbon dioxide atmosphere resulted in dramatic decrease in sensitivity. The role of dissolved oxygen and carbon dioxide in the primary latent track formation and in post-irradiation latent track transformation is discussed. Potential influence of the application of sensitization of CR-39 in radon, neutron and cosmic ray charged particle dosimetry is also discussed.     

Investigation of response of CR-39, PM-355 and PM-500 types of nuclear track detectors to energetic carbon ions

Samples of CR-39, PM-355, and PM-500 plastic detectors were irradiated with carbon ions of energy ranging from 0.9 MeV to 14.7 MeV. After the irradiation the detector samples were etched for a period from 2 hrs to 10 hrs. Dependence of track diameters on the ion energy values for different etching times, and dependence of V_T/V_B as a function of incident carbon-ion energy, are presented.     

Measurement of target fragments produced by 160 MeV proton beam in aluminum and polyethylene with CR-39 plastic nuclear track detectors

Production of target fragments from reactions of 160 MeV proton beams in aluminum and polyethylene was measured with CR-39 plastic nuclear track detectors (PNTD). Due to the detection limit of PNTD, primary protons cannot be detected; only low-energy short-range target fragments are registered. As a feasibility study, a so called “two step etching method” was employed to get the linear energy transfer (LET) spectra, absorbed dose, and dose equivalent. This method is discussed in this paper, together with the measured results.     

Advantage of PM-355 nuclear track detector in light-ion registration and high-temperature plasma diagnostics

Detailed calibration studies of selected types of SSNTDs have been performed at the SINS using monoenergetic light ions of energy within MeV range. These studies were motivated by the application of such detectors in the optimal way for plasma physics experiments. This paper shows track diameter evolutions versus particle energy and etching time. Some conclusions related to track registration phenomenon and detection properties of the investigated detectors, especially of the PM-355 type are also presented.     

Track revelation and optical properties of pentaerythritol tetrakis (allyl carbonate) plastic for application as nuclear track detector: effects of gamma radiations

The etching conditions of an indigenously prepared thin film of pentaerythritol tetrakis(allyl carbonate) (PETAC) were standardised for the use as a nuclear track detector. The optimum etching times in 6?N NaOH at 70°C for the appearance of fission and alpha tracks recorded in this detector from a ²⁵²Cf solid source were found to be 30 min and 1.50?h, respectively. The experimentally determined values for the bulk and track-etch rates for this detector in 6?N NaOH at 70°C were found to be 1.7?±?0.1 and 88.4?±?10.7?µm/h, respectively. From these results, the important track etching properties such as the critical angle of etching, the sensitivity and the fission track registration efficiency were calculated and compared with the commercially available detectors. The activation energy value for bulk etching calculated by applying Arrhenius equation to the bulk etch rates of the detector determined at different etching temperatures was found to be 0.86?±?0.02?eV. This compares very well with the value of about 1.0?eV reported for most commonly used track detectors. The effects of gamma irradiation on this new detector in the dose range of 200–1000?kGy have also been studied using bulk etch rate technique. The activation energy values for bulk etching calculated from bulk etch rates measurements at different temperatures were found to decrease with the increase in gamma dose indicating scission of the detector due to gamma irradiation. The optical band gap of this detector was also determined using UV–visible spectrometry and the value was found to be 4.37?±?0.05?eV.     

DC conductivity and dielectric constant of cellulose nitrate detector

The temperature dependence of DC conductivity as well as the temperature and frequency dependence of dielectric constant of cellulose nitrate (CN) track detector was undertaken for better understanding of the track response of the detector. In the temperature range −100° to + 100°C, CN is found to be an insulating semiconductor with activation energies 0.04 eV, 0.78 eV and 1.24 eV. The transition of the activation processes takes place at (−10±1)°C and (60±1)°C. The high activation energy transition temperature coincides with the glass transition temperature of CN. The dielectric constant is found to increase with temperature and decrease with frequency. These results reveal the physical basis of the Ion Explosion Spike model of Fleischer et al. (1975). A possible explanation of the registration temperature effect is also given on the basis of these results.     

Determination of spatial and energy distributions of neutrons in experiments on transmutation of radioactive waste using relativistic protons

The experiments on transmutation of ¹²⁹I and ²³⁷Np using uranium-lead targets surrounded by a paraffin moderator were performed at the Joint Institute for Nuclear Research (JINR, Russia). The targets were irradiated by 1.5 GeV and 7.4 GeV protons at the Synchrophasotron of JINR. In the frame of present work spatial and energy distributions of neutrons on the surface of the paraffin moderator were measured using SSNTD technique. It is shown that measured values of spetral indices do not pretend on the energy of incident protons but depend on the target composition. The presence of the uranium insertion softens neutron spectra.