Dose-dependent optically stimulated luminescence of synthetic quartz at room temperature

Physical conditions such as annealing temperature, duration of annealing, ionizing radiation, etc., play a significant role in the applications of optically stimulated luminescence (OSL) dating as well as OSL dosimetry. Many efforts are made to understand the effect of these physical parameters on quartz specimens owing to its use in such applications. Such factors induce changes in OSL decay pattern. The definite correlation between color centers and luminescence sensitivity can be established on account of such pre-treatments to the specimen.The purpose of present investigations is to study the effect of ionizing radiation under identical physical conditions on OSL properties measured at room temperature. The shapes of decay curve and dose-response data are considered for this purpose. This study can reveal the changes in color centers in response to the pre-conditions to the specimen. It was found that the OSL decay remains slow and OSL properties change systematically with the rise in beta dose up to a critical dose; however, it changes the pattern when the beta exposure to the specimen was increased higher than the critical dose. This critical dose was found to be different for different temperature of annealing. The shape of decay curve up to the critical dose was also studied by considering the difference of OSL intensities between two successive durations from the observed OSL decay data. The results are explained based on the changes in available shallow traps during OSL measurement at room temperature with changes in pre-conditions to the specimens. The results also have been confirmed with the corresponding changes in ESR signals.     

Characteristics of LM-OSL from several different types of quartz

We present Linear-Modulation OSL (LM-OSL) curves from several different types of quartz, including sedimentary quartz, bulk rock crystal and synthetic quartz. The LM-OSL method consists of linearly increasing the intensity of the stimulation light while continuously monitoring the OSL emission from the sample. With this technique, one obtains peaks of luminescence intensity versus time (Bulur, 1996) in which the position of the peak is inversely related to the photoionization cross-section of the trap. The shape of the LM-OSL curve is directly related to the shape of the conventional OSL decay curve in which the stimulating light source is maintained at constant intensity (so-called Continuous-Wave OSL, or CW-OSL). In the latter, the OSL from the traps with the highest photoionization cross-section decays most rapidly with stimulation time, while OSL from those traps with smaller photoionization cross-sections is characterized by longer decay times. In this paper, data are presented comparing the CW-OSL and LM-OSL curves for several different quartz types with particular focus on the changes in the shapes of each of these curves with sample type pre-heat temperature, and measurement temperature. Several different LM-OSL components are found for each sample, each with different photoionization cross-sections, but a universal behavior for quartz is not observed; each sample is different. From the dependence upon pre-heat temperature, features associated with shallow traps can be identified. Traps which empty very rapidly can be observed more easily in the LM-OSL curves than in the conventional CW-OSL curves, and the temperature dependence of the photoionization cross-section for the various components can be clearly discerned.     

Comparative study on the effect of annealing treatments on RTL mechanism in natural quartz from different origins

The behaviour of trap centres and luminescence centres has been investigated for fired and unfired natural quartz from bricks and sediments irradiated at 100 Gy and annealed at different temperatures in the range 350-700 °C. The annealing treatment affects thermoluminescence (TL) glow curve as various changes were observed. The higher sensitization occurred for an annealing in the region 550-600 °C. At this annealing temperature, it has been observed the emergence of two peaks arising at 96 and 180 °C. At lower annealing temperatures, these peaks are overlapped by the peaks localized at 90 and 195 °C, respectively. Concerning the fired quartz, the higher sensitization occurred for an annealing in the region 500-550 °C for peak temperature around 200 °C and an unusual desensitization for the peak temperature around 100 °C. The behaviour of the two types of quartz is analyzed regarding to their kinetic parameters and luminescence emission and compared to literature data.     

The TL and room temperature OSL properties of the glow peak at 110 °C in natural milky quartz: A case study

The LM–OSL signal of quartz, while measured at room temperature, is dominated by an intermediate, broad and intense OSL component, so that its contribution and general characteristics are derived very accurately. Through a series of dose–response, bleaching and thermal decay at room temperature experiments, in conjunction with curve fitting studies, a component resolved analysis is carried out studying the correlation between this specific component, termed as LM–OSL component C₂ and the 110 °C TL glow peak in quartz. The dose–response of these two luminescence components behaves exactly similar being linear at low doses and saturating at almost 100 Gy. Both signals decay exponentially under illumination, providing identical optical detrapping cross-section values. Residual of both luminescence signals after thermal decay at room temperature follows an exponential law, yielding similar mean half-lives. All previous luminescence features provide strong evidence for the electron trap being the same for both the 110 °C TL trap and the LM–OSL component C₂. The results of the present work are very promising and clearly support the possibility of extrapolating the TL pre-dose methodology to the OSL pre-dose effect using only the LM–OSL component C₂.     

Luminescence properties of biotite relevant to dating and dosimetry

Biotite mineral grains from granitic rocks were subjected to luminescence studies with optical and thermal stimulation. Moderate thermoluminescence (TL) signals and weak optically stimulated luminescence (OSL) with blue-green light stimulation were detected after 50 Gy beta irradiation. No detectable infrared-stimulated luminescence (IRSL) was observed for natural and laboratory beta-irradiated samples. TL peaks at 118, 300, 360 and 480 °C can be identified from laboratory-irradiated samples. The 360 °C TL peak saturates at a higher dose than quartz, but shows significant anomalous fading after 80 days stored at room temperature. The potentials and problems for biotite used as a natural dosimeter are discussed.     

The influence of electron–phonon interaction on the OSL decay curve shape

The significance of the electron–phonon interaction for optically stimulated luminescence (OSL) process in quartz is demonstrated. OSL variation with temperature has been investigated for four samples of natural quartz. Changes of the OSL decay rate have been observed for all components of the OSL signal. The scale and tendency of these changes are comparable with outcomes of computer simulations carried out for the model composed of two deep electron traps, one shallow trap and one recombination centre, taking into account the electron–phonon interactions.     

Relative response of TL and component-resolved OSL to alpha and beta radiations in annealed sedimentary quartz

Knowledge of the relative luminescence response to alpha and beta radiation is very important in TL and OSL dating. In the present study the relative alpha to beta response is studied in a sedimentary quartz sample, previously fired at 900 °C for 1 h, in the dose region between 1 and 128 Gy, for both thermoluminescence (TL) and linearly modulated optically stimulated luminescence (LM – OSL). The LM – OSL measurements were performed at room temperature and at 125 °C. All OSL signals were deconvolved into their individual components. Comparison of OSL curves after alpha and beta irradiation strongly supports that quartz OSL components follow first order kinetics in both cases. In the case of TL, the relative alpha to beta response is found to be very different for each TL glow-peak, but it does not depend strongly on irradiation dose. In the case of LM – OSL measurements, it is found that the relative behaviour of the alpha to beta response is different for three distinct regions, namely the fast OSL component, the region of medium OSL component originating from the TL glow-peak at 110 °C when stimulation takes place at room temperature and finally the region of slow OSL component. Following stimulation at ambient temperature, the relative alpha to beta response of all components was not observed to depend significantly on dose, with the value of ratio being 0.03 and a tendency to decrease with increasing dose. However, in the case of measurements performed at 125 °C, the relative response of the fast components is much enhanced, and for the remaining components it increases with increasing dose. Special care must be taken to examine the relative alpha to beta response of the fast component at 125 °C which contrasts the relative response of the TL peak at ca. 325 °C. The implications for the dating of annealed quartz are also briefly discussed.     

The influence of optical bleaching on lifetimes and luminescence intensity in the slow component of optically stimulated luminescence of natural quartz from Nigeria

The intensity of optically stimulated luminescence may be decreased to a slow or medium component of its decay curve by optical bleaching, that is, by prolonged exposure of the luminescent sample to stimulating light. In this paper, we report on the influence of irradiation and measurement temperature on luminescence lifetimes as well as on the effect of measurement temperature on luminescence intensity in annealed natural quartz from Nigeria. Measurements were carried out in the slow component region using time-resolved optical stimulation at 470 nm on samples annealed at 500 and 600 °C. Luminescence lifetimes were determined from the resultant time-resolved luminescence spectra by analysing the portion of each spectrum after the stimulating light pulse of duration 11 μs. In preparatory tests, the influence of the duration of optical bleaching on lifetimes was investigated. It was found that lifetimes in samples annealed at 500 °C are independent of the duration of optical bleaching, whereas lifetimes in quartz annealed at 600 °C are affected, decreasing towards a constant value with duration of bleaching. Concerning measurements in the slow-component region, lifetimes were found to decrease with irradiation dose for samples annealed at either 500 or 600 °C. The temperature dependence of lifetimes in both sets of quartz is similar with lifetimes constant at about 36 μs between 20 and 120 °C, but decreasing consistently from then on to about 5 μs at 200 °C, the maximum measurement temperature used in experiments. The luminescence intensity was observed to typically go through a peak as the stimulation temperature was increased from 20 to 200 °C, following a brief initial decrease, a change better exemplified in the quartz annealed at 600 °C. The initial decrease in luminescence intensity is attributed to the dominance of optical stimulation over thermal stimulation. On the other hand, the subsequent change of luminescence intensity with temperature is discussed as evidence of thermal assistance to optical stimulation, initially with activation energy of 0.27±0.07 eV and of thermal quenching subsequently with activation energy equal to 0.93±0.23 eV for samples annealed at either 500 or 600 °C. The temperature dependence of lifetimes is explained as showing increased thermal effect on lifetimes with activation energy values within 0.83±0.01 eV. On the other hand, the influence of irradiation on lifetimes is accounted for in terms of an energy band model for quartz consisting of three luminescence centres and one non-radiative recombination centre.     

Simulations of the effect of pulse annealing on optically-stimulated luminescence of quartz

Pulse annealing techniques are commonly used in OSL studies of quartz to obtain information on the kinetic parameters of OSL traps and hole reservoirs. In this paper, simulations of pulse annealing experiments are carried out using the comprehensive model for quartz developed by Bailey [2001. Towards a general kinetic model for optically and thermally stimulated luminescence of quartz. Radiat. Meas. 33, 17–45] for both natural and laboratory irradiated aliquots. The results of the simulations are in qualitative agreement with, and reproduce, several unusual features of the experimental data of Wintle and Murray [1998. Towards the development of a preheat procedure for OSL dating of quartz. Radiat. Meas. 29, 81–94]. The simulations are also carried out using different heating rates, and show that pulse annealing experiments can be used to recover appropriate kinetic parameters for both the OSL traps and the hole reservoirs known to exist in quartz. The results of the simulations show the importance of these hole reservoirs in determining how the OSL signal depends upon the preheat temperature.     

TL, OSL and ESR studies on beryllium oxide

Electron spin resonance (ESR) studies were carried out to identify the defect centres responsible for the thermoluminescence (TL) and optically stimulated luminescence (OSL) processes in BeO phosphor. Two defect centres were identified in irradiated BeO phosphor by ESR measurements, which were carried out at room temperature and these were assigned to an O⁻ ion and Al²⁺ centre. The O⁻ ion (hole centre) correlates with the main 190 °C TL peak. The Al²⁺ centre (electron centre), which acts as a recombination centre, also correlates to the 190 °C TL peak. A third centre, observed during thermal annealing studies, is assigned to an O⁻ ion and is related to the high temperature TL at 317 °C. This centre also appears to be responsible for the observed OSL process in BeO phosphor.     

Thermoluminescent and stuctural properties of BaAl2O4:Eu,Nd,Gdphosphors prepared by combustion method

BaAl₂O₄:Eu²⁺,Nd³⁺,Gd³⁺ phosphors were prepared by a combustion method at different initiating temperatures (400–1200 °C), using urea as a comburent. The powders were annealed at different temperatures in the range of 400–1100 °C for 3 h. X-ray diffraction data show that the crystallinity of the BaAl₂O₄ structure greatly improved with increasing annealing temperature. Blue-green photoluminescence, with persistent/long afterglow, was observed at 498 nm. This emission was attributed to the 4f⁶5d¹–4f⁷ transitions of Eu²⁺ ions. The phosphorescence decay curves were obtained by irradiating the samples with a 365 nm UV light. The glow curves of the as-prepared and the annealed samples were investigated in this study. The thermoluminescent (TL) glow peaks of the samples prepared at 600 °C and 1200 °C were both stable at ∼72 °C suggesting that the traps responsible for the bands were fixed at this position irrespective of annealing temperature. These bands are at a similar position, which suggests that the traps responsible for these bands are similar. The rate of decay of the sample annealed at 600 °C was faster than that of the sample prepared at 1200 °C.     

White light-emitting diodes for optical stimulation of aluminium oxide in OSL dosimetry

The results of comparative investigations into the optically stimulated luminescence (OSL) of anion-defective corundum excited by radiation of blue and white light-emitting diodes (LEDs) are reported. The continuous-wave OSL (CW-OSL) measurements showed that the white LED (compared to the blue LED) and the chosen geometry allow the amplitude of the OSL response to increase by a factor of more than 40 and the dosimetric information readout time to decrease by a factor of 20.The effect of deep traps on the behavior of the CW-OSL curves of anion-defective corundum was studied. It was found that the filling of deep traps essentially increases the TL yield with a dosimetric peak at 450 K and the CW-OSL-yield under stimulation with blue and white LEDs. It was also found that this filling causes a considerable change in the shape of the OSL curve and the time parameters of the decay.     

LiMgPO_4:Tm,Tb的热释光和光释光陷阱参数

采用高温固相法合成了LiMgPO_4:Tm,Tb粉末样品,测定了热释光陷阱参数激发能E和频率因子s.用脉冲退火和多次退火方法研究了其光释光陷阱参数E和s,并与用多速法得到的热释光的结果进行了比较.对不同β射线剂量照射的样品发光曲线的研究表明,300°C高温峰属于一级动力学发光峰.通过对热释光和光释光陷阱的相关性研究表明,经200°C预热的热释光信号(对应于300°C高温峰)和光释光信号很有可能来自于同一深度的陷阱.     

Optical depth of traps in AL2O3:C determined by the variable energy of stimulation OSL (VES-OSL) method

Standard methods of OSL measurements (CW-OSL or LM-OSL) do not allow for the direct determination of optical depth of traps. The variable energy of stimulation optically stimulated luminescence (VES-OSL) method gives such possibility. It consists in optical stimulation with the continuous increase of stimulation light energy and is analogous to the glow curve method in TL measurements. The VES-OSL curve shape and maximum position can be regulated by the stimulation photon flux, the rate of stimulation energy increase and by measurement temperature. This allows for detecting the OSL from very deep traps that give the TL signal overlapping with strong incandescence. The VES-OSL measurements carried out for Al₂O₃:C showed that traps having the optical depth between 2.0 and 2.8 eV are responsible for the OSL signal related to TL peak at about 200 °C. The OSL signal from the much deeper traps from the range 2.8–3.3 eV was also detected. The TL signal related do these traps cannot be detected below 500 °C.     

Effects of neutron irradiation and subsequent annealing on the optical characteristics of sapphire

In this paper, the effect of neutron irradiation on sapphire single crystal with fast neutron of 1.0×10¹⁸ and 1.0×10¹⁹ neutrons/cm² has been investigated along with the effect of annealing temperature. It is found that the colorless transparent sapphire single crystals were turned yellow after 10 MeV fast neutron irradiation at room temperature. There are peaks at 206, 230, 258, 305, 358 and 452 nm after neutron irradiation. And the intensity of optical absorption bands decrease with wavelength and annealing temperature. A new absorption peak at 452 nm was found after isothermal annealing at 400 °C for 10 min, which was ascribed to F₂⁺ color center. Because of the recombination of interstitial ions and vacancies, color centers were almost removed after annealing at 1000 °C. The TL peaks were found to shift to higher temperature after neutron irradiation. And a higher fluence of the neutron irradiation would result in deep traps revealed as the new TL peaks at 176 and 227 °C.     

Modelling the thermal bleaching of OSL signal in the case of a competition between recombination centres

The thermal bleaching of the optically stimulated luminescence (OSL) has been investigated by computer simulations for a model including three traps and two luminescence centres. The deepest trap is active only during the OSL process. Two other traps are active only during the thermal bleaching. The thermal bleaching effects on the OSL intensity as well as on the OSL curve shape are presented for the wide range of trap and luminescence centre parameters and for the different settings of optical detection window. The conventional OSL curve analysis consisting in decomposition of the OSL curve into first order components is applied to the simulation results and the optical cross section spectra obtained as a result of this analysis are compared with the model assumptions. The simulations show that OSL signal can decrease to undetectable level even when the traps related to this signal are not emptied during thermal bleaching. The residual level of the OSL signal after bleaching process, however, depends strongly on centre parameters and concentrations. The modifications of optical detection spectral window lead to significant changes of bleaching effects. The thermal bleaching influences also the optical cross section spectra obtained as a result of the OSL curve decomposition.     

Structural, compositional, thermal resistant and hydro-oleophobic properties of fluorine based block-co-polymer films on quartz substrates by wet chemical process

Crack free and smooth surfaces of poly [4,5-difluoro 2,2-bis (trifluoromethyl)-(1,3 dioxole)-co-tetrafluoroethylene] (TFE-co-TFD) thin films have been deposited by wet chemical dip coating technique on polished quartz and glass slide substrates. The deposited films have been subjected to annealing at different temperatures ranging from 100 to 500 °C for 1 h in argon atmosphere. The elemental composition of the as-deposited (xerogel) thin film as well as film annealed at 400 °C was measured by X-ray photoelectron spectroscopy and observed that there was no change in the composition of the film. X-ray diffraction pattern revealed the amorphous behaviour of both as-deposited and film annealed at 400 °C. Surface morphology and elemental composition of the films have been examined by employing scanning electron microscopy attached with energy dispersive X-ray analyser, respectively. It was found that as the annealing temperature increased from 100 to 400 °C, nano-hemisphere-like structures have been grown, which in turn has shown increase in the water contact angle from 122^o to 148^o and oil (peanut) contact angle from 85° to 96°. No change in the water contact angle (122°) has been observed when the films deposited at room temperature were heated in air from 30 to 80 °C as well as exposed to steam for 8 days for 8 h/day indicating thermal stability of the film.     

Temperature dependence of the stability of written bits in a magnetic hard-disk medium investigated by magnetic force microscopy

The thermal stability of written bits in a magnetic hard-disk medium has been investigated with a magnetic force microscope (MFM), which was equipped with an in situ heating system capable of heating the medium up to 300 °C. It is shown that both the annealing temperature and the duration have significant effect on the decay of the MFM signal. No signal decay is observed when annealing for 30 min up to temperatures of 200 °C. The MFM signal decays rapidly with increasing temperature, for temperatures over 200 °C. Repeated annealing at 280 °C with a duration below 10 min does not cause any signal decay.     

Luminescence properties of BeO optically stimulated luminescence (OSL) detectors

The objective of this work is to investigate basic luminescence properties of BeO optically stimulated luminescence (OSL) detectors, including the OSL emission and stimulation spectrum, the lifetime of the luminescence centers contributing to the OSL signal, and the temperature dependence of the luminescence lifetime and of the luminescence efficiency. The OSL stimulation spectrum shows a continuous increase in OSL intensity with decreasing stimulation wavelength. The emission spectrum indicates two OSL emission bands at ～310 nm and ～370 nm, the latter being the dominant OSL emission band. We also observed that the luminescence centers associated with the OSL signal are strongly quenched above room temperature, resulting in a reduction in luminescence lifetime from ～27 μs at room temperature down to ～800 ns at 140 °C. The activation energy for non-radiative decay of the luminescence center was determined to be E = (0.568 ± 0.023) eV. The ～27 μs luminescence lifetime observed for BeO indicate that POSL technique may be used to improve the signal-to-noise ratio using stimulation pulses of the order of microseconds. The information obtained in this study may help further optimize the BeO dosimetry systems and provide guidance on the timing parameters to be used for POSL measurements of this material.