Luminescence of Ce and Pr doped Sr2Mg(BO3)2 under VUV-UV and X-ray excitation

This report presents the luminescence properties of Ce³⁺ and Pr³⁺ activated Sr₂Mg(BO₃)₂ under VUV-UV and X-ray excitation. The five excitation bands of crystal field split 5d states are observed at about 46 729, 44 643, 41 667, 38 314 and 29 762 cm⁻¹ (i.e. 214, 224, 240, 261 and 336 nm) for Ce³⁺ in the host lattice. The doublet Ce³⁺ 5d→4f emission bands were found at about 25 840 and 24 096 cm⁻¹ (387 and 415 nm). The influence of doping concentration and temperature on the emission characteristics and the decay time of Ce³⁺ in Sr₂Mg(BO₃)₂ were investigated. For Pr³⁺ doped samples, the lowest 5d excitation band was observed at about 42017 cm⁻¹ (238 nm), a dominant band at around 35714 cm⁻¹ (280 nm) and two shoulder bands were seen in the emission spectra. The excitation and emission spectra of Ce³⁺ and Pr³⁺ were compared and discussed. The X-ray excited luminescence studies show that the light yields are ∼3200±230 and ∼1400±100 photons/MeV of absorbed X-ray energy for the samples Sr_1.86Ce_0.07Na_0.07Mg(BO₃)₂ and Sr_1.82Pr_0.09Na_0.09Mg(BO₃)₂ at RT, respectively.     

KBaPO4:Ln (Ln=Eu, Tb, Sm) phosphors for UV excitable white light-emitting diodes

This letter reports the novel three emission bands based on phosphate host matrix, KBaPO₄ doped with Eu²⁺, Tb³⁺, and Sm³⁺ for white light-emitting diodes (LEDs). The phosphors were synthesized by solid-state reaction and thermal stability was elucidated by measuring photoluminescence at higher temperatures. Eu²⁺-doped KBaPO₄ phosphor emits blue luminescence with a peak wavelength at 420 nm under maximum near-ultraviolet excitation of 360 nm. Tb³⁺-doped KBaPO₄ phosphor emits green luminescence with a peak wavelength at 540 nm under maximum near-ultraviolet excitation of 370 nm. Sm³⁺-doped KBaPO₄ phosphor emits orange-red luminescence with a peak wavelength at 594 nm under maximum near-ultraviolet excitation of 400 nm. The thermal stabilities of KBaPO₄:Ln (Ln=Eu²⁺, Tb³⁺, Sm³⁺), in comparison to commercially available YAG:Ce³⁺ phosphor were found to be higher in a wide temperature range of 25-300 °C.     

Thermally stable blue-emitting NaSrPO4:Eu phosphor for near UV white LEDs

A novel blue light emitting NaSr_1 − xPO₄:Eu²⁺_x (x = 0.001 to 0.02) phosphors were prepared by solid-state reaction method to investigate its optical properties and thermal stability for its application in white light-emitting diodes (w-LEDs). The excitation and emission spectra of the prepared phosphor reveal a broad emission peak centered at 460 nm which arises due to 4f-5d transitions of Eu²⁺ upon the near ultra-violet (n-UV) excitation wavelength at 380 nm. The effect of Eu²⁺ doping concentration and sintering temperature on the emission intensity of NaSrPO₄:Eu²⁺ was investigated along with its chromaticity coordinates. The temperature dependent luminescence properties of the prepared phosphor show better results than that of the commercial YAG:Ce³⁺phosphor. Besides, their XRD, FT-IR, SEM, TG, and DTA profiles have also been analyzed to explore its structural details.     

Optical properties of blue emitting Ce activated XMg2Al16O27 (X = Ba, Sr) phosphors

Here we reported that the optical properties of novel blue-emitting Ce³⁺ activated XMg₂Al₁₆O₂₇ (X = Ba, Sr) phosphors were prepared by combustion method successfully. The excitation spectrum shows a broad band extending from 280 to 380 nm, centered at 355 nm, and the emission spectrum shows intense blue emission broad band centering at 441 nm for Ba²⁺ and Sr²⁺ host lattices. XRD pattern indicates crystalline nature of prepared phosphors. SEM analysis shows morphology of the ternary-hexaaluminate based phosphor prepared by combustion method. The Ce³⁺ activated XMg₂Al₁₆O₂₇ (X = Ba, Sr) should be a promising blue phosphor for near ultraviolet-based white-light-emitting diodes.     

The luminescence and structural characteristics of Eu- doped NaSrB5O9 phosphor

A red-emitting phosphor NaSrB₅O₉:Eu³⁺ was synthesized by employing a solid-state reaction (SSR) method. The structures of the phosphors were analyzed by X-ray diffraction (XRD), Fourier-transform infrared (FTIR) and Raman studies. The band at ~282 nm in the excitation spectra indicated the charge transfer band (CTB) of B-O in the host, whereas the CTB of Eu-O was observed at ~275 nm for the NaSrB₅O₉:Eu³⁺ (Eu³⁺=1 at.%) phosphor, which was supported by diffuse reflectance spectroscopy (DRS) measurements. The photoluminescence (PL) measurements exhibited a strong red emission band centered at about 616 nm (⁵D₀→⁷F₂) under an excitation wavelength of 394 nm (⁷F₀→⁵L₆). Upon host excitation at 282 nm, the pristine NaSrB₅O₉ exhibited a broad UV emission centered at ~362 nm. The energy transfer from host to Eu³⁺ ions was confirmed from luminescence spectra, excited with a 355 nm Nd:YAG laser. In addition, the asymmetric ratios indicate a higher local symmetry around the Eu³⁺ ion in the host. The calculated CIE (Commission International de l′Eclairage) coordinates displayed excellent color purity efficiencies (around 99.7%) compared to other luminescent materials.     

Dual mode emission and harmonic generation in ZnO-CaO-Al2O3: Er nano-composite

Er³⁺ doped ZnO-CaO-Al₂O₃ nano-composite phosphor has been synthesized through combustion method and its emission and harmonic generation properties have been studied. The X-ray diffraction and thermal analysis techniques have been used to prove the dual phase (ZnO and CaO-Al₂O₃) nature of the phosphor. The phosphor has shown up-conversion emission on near-infra-red (976 nm) excitation and down-conversion emission on 355 nm excitation in presence of Er³⁺ and thus behaves as a dual mode phosphor. On excitation with 976 nm diode laser, material shows color tunability (calcination of composite material at different temperatures). Formation of ZnO nanocrystals on heat treatment of as-synthesized sample has shown its characteristic emission at 388 nm and also the energy transfer from ZnO to Er³⁺ ions. The low temperature emission measurements have been carried out and the results have been discussed. Phosphor has shown strong second harmonic generation (SHG) at 532 nm on 1064 nm and at 266 nm on 532 nm excitation.     

Site selective 4f5d spectroscopy of CaF2 : Pr

Spectroscopic investigations were performed on a single crystal of CaF₂ doped with 0.05% Pr³⁺. Three different Pr³⁺ sites with different luminescent properties were identified. The 4f² →4f¹5d¹ excitation spectrum of the first site has a sharp maximum at 221.3 nm. Excitation in the 4f5d bands of this site yields strong 4f5d emissions in the UV/VIS part of the spectrum and also weaker intraconfigurational 4f² emissions. By comparing the intraconfigurational 4f emissions and their decay times with data from the literature, these 4f5d bands are assigned to transitions on Pr³⁺ ions on a site with C_4V symmetry. The fd excitation spectrum of the second site has a zero phonon line at 223.3 nm. Upon selective excitation in this band, only 4f5d emission is observed. Probably, these 4f5d bands correspond to Pr³⁺ ions on a O_h site. The third set of 4f5d bands has a 4f5d onset at 208 nm. By comparison of the luminescence spectra of the intraconfigurational 4f² transitions with literature data, these transitions are assigned to Pr³⁺ on an L site. Excitation in these 4f5d band yields ¹S₀ emission followed by emission from the ³P₀ state. The present results clarify some contradictions reported in the literature.     

Luminescence property of Ce-doped silica decorated with S and Cl anions

Ce³⁺-doped silica was synthesized by sol-gel technique and was further decorated with S²⁻ and Cl⁻ anions through chemical exchange in controlled ambient at elevated temperature. The structure and optical property of samples were examined by X-ray diffraction spectrum, XPS pattern, reflection pattern, and photoluminescence patterns. There is a broad luminescence band at 445 nm under the excitation at 320 nm in the Ce³⁺-doped silica heat-treated in air at 1000 °C. The heat-treatment of the sample in vacuum at 800 °C can increase the intensity of luminescence but have no effect on the wavelength of luminescence. The decoration of S²⁻ and Cl⁻ anions cannot only increase the luminescent intensity but also shift the luminescent wavelength to shorter wavelength.     

White-light emission derived from yttrium tungstate-chloride xerogel without activator ions

White xerogel powder of yttrium tungstate-chloride was synthesized, and its photoluminescence properties were investigated. Under the excitation of 254 nm, the xerogel phosphor exhibits emission ranging from 300 to 650 nm. This luminescent spectrum is identified as two emission bands of 300-400 and 400-650 nm due to different emission mechanism. While the emission band of 300-400 nm is ascribed to the charge transfer (CT) from O to metal W, the emission of 400-650 nm is attributed to electron-hole (e⁻-h⁺) carrier emission related to oxygen vacancies. By calcining the sample in reducing atmosphere, the number of oxygen vacancies acting as luminescence centers is increased. As a result, the emission intensity of 400-650 nm is significantly enhanced. Based on electron paramagnetic resonance and spectral analysis, the mechanism of peroxy-radical hole traps (PRHT) is proposed for the luminescence of 400-650 nm.     

Characterization of the VUV excitation spectrum of BaZr(BO3)2:Eu

The excitation spectra of M (M=Si⁴⁺, Ti⁴⁺) and Eu³⁺ co-doped BaZr(BO₃)₂, BaZrO₃:Eu and La₂Zr₂O₇:Eu in the vacuum ultraviolet (VUV) regions of 110-300 nm are investigated and the host-lattice absorption are characterized. The result indicated that BaZr(BO₃)₂:Eu³⁺ phosphor has a strong absorption under the VUV excitation, and in the host-lattice excitation, the strong band at 130-160 nm could be due to the BO₃ atomic groups; the band at 160-180 nm is related to the excitation of Ba-O; 180-200 nm corresponds to the charge transfer (CT) transition of Zr-O. The band at 200-235 nm due to the CT band of Eu³⁺-O²⁻ and a bond valence study explained the observed weak CT band of Eu³⁺-O²⁻ in the excitation spectra of BaZr(BO₃)₂:Eu³⁺. The emission results show that Si⁴⁺ can sensitize luminescence in the host of BaZr(BO₃)₂:Eu but Ti⁴⁺ has no improvement effect on luminescence.     

Afterglow mechanism and thermoluminescence of red-emitting CaS:Eu,Pr phosphor with incorporated Li ion upon visible light irradiation

This paper reports on the afterglow mechanism and thermoluminescence (TL) of a red-emitting CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion upon irradiation by visible light (D₆₅ lamp). In the TL glow curve of the CaS:Eu²⁺,Pr³⁺ phosphor, a TL peak was observed near 120 °C. The luminescence center of the CaS:Eu²⁺,Pr³⁺ phosphor was the Eu²⁺ ion and the trap depth of the CaS:Eu²⁺,Pr³⁺ phosphor with the cation vacancy (Trap 1) which formed by incorporation of the Pr³⁺ ion was 0.202 eV. A cation vacancy (Trap 2) was formed by incorporation of the Li⁺ ion in the CaS:Eu²⁺,Pr³⁺ phosphor. In the TL glow curve of the CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion, two TL peaks were observed near 120 and 200 °C. The TL luminance of the CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion increased with an increase in the initial Li/Ca atomic ratio. The two TL peaks moved to the high-temperature side with an increase in heating rate. The cation vacancy (Trap 2) calculated from the Hoogenstraaten method was 0.118 eV. The afterglow time of the CaS:Eu²⁺,Pr³⁺ phosphor with incorporated Li⁺ ion was prolonged by generation of a shallow trap.     

Simultaneous three-photon absorption induced ultraviolet upconversion in Pr:Y2SiO5 crystal by femtosecond laser irradiation

Near-infrared to ultraviolet upconversion luminescence was observed in the Pr³⁺:Y₂SiO₅ crystal with 120 fs, 800 nm infrared laser irradiation. The observed emissions at around 270 nm and 305 nm could be assigned to 5d → 4f transitions of Pr³⁺ ions. The relationship between the upconversion luminescence intensity and the pump power of the femtosecond laser reveals that the UV emission belongs to simultaneous three-photon absorption induced upconversion luminescence.     

Combustion synthesis and luminescence properties of NaY1−xEux(WO4)2 phosphors

The red phosphors NaY_1−xEu_x(WO₄)₂ with different concentrations of Eu³⁺ were synthesized via the combustion synthesis method. As a comparison, NaEu(WO₄)₂ was prepared by the solid-state reaction method. The phase composition and optical properties of as-synthesized samples were studied by X-ray powder diffraction and photoluminescence spectra. The results show that the red light emission intensity of the combustion synthesized samples under 394 nm excitation increases with increase in Eu³⁺ concentrations and calcination temperatures. Without Y ions doping, the emission spectra intensity of the NaEu(WO₄)₂ phosphor prepared by the combustion method fired at 900 °C is higher than that prepared by the solid-state reaction at 1100 °C. NaEu(WO₄)₂ phosphor synthesized by the combustion method at 1100 °C exhibits the strongest red emission under 394 nm excitation and appropriate CIE chromaticity coordinates (x=0.64, y=0.33) close to the NTSC standard value. Thus, its excellent luminescence properties make it a promising phosphor for near UV InGaN chip-based red-emitting LED application.     

Energy transfer in LaMgB5O10:Pr,Mn under VUV excitation

Luminescent properties of Pr³⁺ or Mn²⁺ singly doped and Pr³⁺, Mn²⁺ co-doped LaMgB₅O₁₀ are investigated by synchrotron radiation VUV light. When LaMgB₅O₁₀:Pr³⁺ is excited at185 nm, the photon cascade emission between 4f levels of Pr³⁺ is observed. In the excitation spectra of LaMgB₅O₁₀:Mn²⁺ monitoring the 615 nm emission of Mn²⁺, several excitation bands in a spectral range from 330 to 580 nm are recorded, among which the most intense band is centered at 412 nm (⁶A_1g→⁴E_g-⁴A_1g). This band has considerable spectra overlap with the 410 nm emission (¹S₀→¹I₆) of Pr³⁺, which is favorable for energy transfer from Pr³⁺ to Mn²⁺. Such energy transfer is observed in the co-doped sample, converting the violet emission (410 nm) of Pr³⁺ into the red emission (615 nm) of Mn²⁺. The concentration dependence of transfer efficiency is also investigated.     

Photoluminescence properties of thenardite activated with Eu

Na₂SO₄:Eu phosphors were prepared by heating pure natural thenardite with EuF₃ at 900 °C for 20 min in air. The photoluminescence (PL) and excitation spectra of as-prepared and γ-ray-irradiated phosphors were observed at 300 K. The PL spectrum under 394 nm excitation consisted of strong narrow bands with peaks at 579, 592, 616, 652, 697 and 741 nm, assigned to the ⁵D₀→⁷F_J (J=0, 1, 2, …, 5) transitions, respectively, within Eu³⁺. The PL spectrum under 340 nm excitation consisted of a broad Eu²⁺ band with a peak at 435 nm. The excitation spectrum obtained by monitoring the violet luminescence consisted of a weak band with a peak at approximately 261 nm and a broad Eu²⁺ band with a peak at approximately 338 nm. The relative efficiency of the violet luminescence of the γ-ray-irradiated phosphor at the exposure of 46 kGy increased up to 3.0 times that of the unirradiated phosphor. The enhancement of violet luminescence by γ-ray irradiation was ascribed to the conversion of Eu³⁺ to Eu²⁺ in Na₂SO₄.     

SrS:Ce/ZnS:Mn-A di-band phosphor for near-UV and blue LED-converted white-light emitting diodes

The SrS:Ce/ZnS:Mn phosphor blends with various combination viz 75:25, 50:50 and 25:75 were assign to generate the white-light emission using near-UV and blue-light emitting diodes (LED) as an excitation source. The SrS:Ce exhibits strong absorption at 427 nm and the corresponding intense emission occurs at 480 and 540 nm due to electron transition from 5d(²D)−4f(²F_5/2, _7/2) of Ce³⁺ ion as a result of spin-orbit coupling. The ZnS:Mn excited under same wavelength shows broad emission band with λ_max=582 nm originates due to 3d (⁴G−⁶S) level of Mn²⁺. Photoluminescence studies of phosphor blend excited using near-UV to blue light confirms the emitted radiation varies from cool to warm white light in the range 430-600 nm, applicable to LED lightings. The CIE chromaticity coordinate values measured using SrS:Ce/ZnS:Mn phosphor blend-coated 430 nm LED pumped phosphors in the ratio 75:25, 50:50 and 25:75 are found to be (0.235, 0.125), (0.280, 0.190) and (0.285, 0.250), respectively.     

Effect of Ca and Sr alkaline earth ions on luminescence properties of BaAl12O19:Eu nanophosphor

Nanosized barium aluminate materials was doped by divalent cations (Ca²⁺, Sr²⁺) and Eu²⁺ having nominal compositions Ba_1−xMxAl₁₂O₁₉:Eu (M=Ca and Sr) (x=0.1-0.5), were synthesized by the combustion method. These phosphors were characterized by XRD, scanning electron microscopy-energy-dispersive spectrometry (SEM-EDS) and photoluminescence measurement. The photoluminescence characterization showed the presence of Eu ion in divalent form which gave emission bands peaking at 444 nm for the 320 nm excitation (solid-state lighting excitation), while for 254 nm it gave the same emission wavelength of low intensity (1.5 times) compared to 320 nm excitation. It was also observed that alkaline earth metal (Ca²⁺ and Sr²⁺) dopants increase the intensity of Eu²⁺ ion in BaAl₁₂O₁₉ lattice, thus this phosphor may be useful for solid-state lighting.     

Luminescence and EPR studies of Eu doped BaAl12O19 blue light emitting phosphors

Europium doped BaAl₁₂O₁₉ powder phosphors have been synthesized by combustion process within few minutes. The phosphors have been characterized by XRD, SEM, FT-IR, EPR and PL techniques. The EPR spectrum exhibits an intense resonance signal at g=1.96 characteristic of Eu²⁺ ions. In addition to this two weak resonance signals have been observed at g=2.28 and g=4.86. The population of the spin levels (N) for the resonance signal at g=1.96 is calculated as a function of temperature. By post-treating the phosphor at 1350 °C under a reducing atmosphere, it is observed that the population of spin levels has been increased five times. The excitation spectrum shows a peak at 326 nm with a shoulder at 290 nm. Upon excitation at 326 nm, the emission spectrum exhibits a well defined broad band with maximum at 444 nm emitting a blue light corresponding to 4f⁶5d→4f⁷ transition. The luminescence intensity also has been enhanced to 60% by post-treating the phosphor at 1350 °C under a reducing atmosphere.     

Luminescence studies of rare earth doped yttrium gadolinium mixed oxide phosphor

This paper reports the photoluminescence and thermoluminescence properties of gamma ray induced rare earth doped yttrium gadolinium mixed oxide phosphor. The europium (Eu³⁺) was used as rare earth dopant. The phosphor was prepared by chemical co-precipitation method according to the formula (Y_2−x−yGd_x) O₃: Eu_y³⁺ (x=0.5; y=0.05). The photoluminescence emission spectrum of the prepared phosphor shows intense peaks in the red region at 615 nm for ⁵D₀→⁷F₂ transitions and the photoluminescence excitation spectra show a broad band located around 220–270 nm for the emission wavelength fixed at 615 nm. The thermoluminescence studies were carried out after irradiating the phosphor by gamma rays in the dose range from 100 Gy to 1 KGy. In the thermoluminescence glow curves, one single peak was observed at about 300 °C of which the intensity increases linearly in the studied dose range of gamma rays. The glow peak was deconvoluted by GlowFit program and the kinetic parameters associated with the deconvoluted peaks were calculated. The kinetic parameters were also calculated by various glow curve shape and heating rate methods.     

Near-infrared emissions and quantum efficiencies in Tm-doped heavy metal gallate glasses for S- and U-band amplifiers and 1.8 μm infrared laser

Intense 1.8 μm and efficient 1.48 μm infrared emissions have been recorded in Tm³⁺-doped alkali-barium-bismuth-gallate (LKBBG) glasses with low phonon energies under the excitation of 792 nm diode laser. The maximum emission cross-sections for 1.8 and 1.48 μm emission bands are derived to be 6.26×10⁻²¹ and 3.34×10⁻²¹ cm², respectively, and the peak values are much higher than those in Tm³⁺-doped ZBLAN glass. In low-concentration doping, the full-widths at half-maximum (FWHMs) of the two emission bands are 223 and 122 nm, and the quantum efficiencies of the ³F₄ and ³H₄ levels are proved to be ∼100% and 86%, respectively. When the doping concentration increases to 1 wt%, the quantum efficiency of the ³H₄ level is reduced to 60% due to the cross-relaxation processes in high-concentration doping. Efficient 1.8 μm infrared emission in Er³⁺/Tm³⁺-codoped LKBBG glass has also been achieved under the excitation of 970 nm diode laser, and the probability and the efficiency of non-radiative energy transfer from Er³⁺ to Tm³⁺ are as high as 354 s⁻¹ and 58.4%, respectively. Efficient and broad 1.8 and 1.48 μm infrared emission bands indicate that Tm³⁺-doped LKBBG glasses are suitable materials in developing S- and U-band amplifiers and 1.8 μm infrared laser.