Sonoelectrochemical synthesis of water-soluble CdTe quantum dots

A facile and fast one-pot method has been developed for the synthesis of CdTe quantum dots (QDs) in aqueous phase by a sonoelectrochemical route without the protection of N₂. The morphology, structure and composition of the as-prepared products were investigated by high resolution transmission electron microscopy (HRTEM), X-ray diffraction (XRD) and energy dispersive X-ray spectrometer (EDS). The influences of current intensity, current pulse width, and reaction temperature on the photoluminescence (PL) and quantum yield (QY) of the products were studied. The experimental results showed that the water-soluble CdTe QDs with high PL qualities can be conveniently synthesized without precursor preparation and N₂ protection, and the PL emission wavelength and QY can be effectively controlled by adjusting some parameters. This method can be expected to prepare other QDs as promising building blocks in solar cell, photocatalysis and sensors.     

Synthesis and photoluminescence of water-soluble Mn-doped ZnS quantum dots

The water-soluble Mn²⁺-doped ZnS quantum dots (Mn:ZnS d-dots) were synthesized by using thioglycolic acid (TGA) as stabilizer in aqueous solutions in air, and characterized by X-ray powder diffraction (XRD), UV-vis absorption spectra and photoluminescence (PL) emission spectroscopy. The sizes of Mn:ZnS d-dots were determined to be about 2 nm using XRD measurements and the UV-vis absorption spectra. It was found that the Mn²⁺⁴T₁ → ⁶A₁ emission intensity of Mn:ZnS d-dots significantly increased with the increase of Mn²⁺ concentration, and showed a maximum when Mn²⁺ doping content was 1.5%. If Mn²⁺ concentration continued to increase, namely more than 1.5%, the Mn²⁺⁴T₁ → ⁶A₁ emission intensity would decrease. In addition, the effects of TGA/(Zn + Mn) molar ratio on PL were investigated. It was found that the peak intensity ratio of Mn²⁺⁴T₁ → ⁶A₁ emission to defect-states emission showed a maximum when the TGA/(Zn + Mn) molar ratio was equal to 1.8.     

Photoluminescence quenching of CdTe/CdS core-shell quantum dots in aqueous solution by ZnO nanocrystals

Photoluminescence (PL) properties of 3-mercaptopropionic acid (MPA) coated CdTe/CdS core-shell quantum dots (QDs) in aqueous solution in the presence of ZnO colloidal nanocrystals were studied by steady-state and time-resolved PL spectroscopy. The PL quenching of CdTe/CdS core-shell QDs with addition of purified ZnO nanocrystals resulted in a decrease in PL lifetime and a small red shift of the PL band. It was found that CdTe(1.5 nm)/CdS type II core-shell QDs exhibited higher efficiency of PL quenching than the CdTe(3.0 nm)/CdS type I core-shell QDs, indicating an electron transfer process from CdTe/CdS core-shell QDs to ZnO nanocrystals. The experimental results indicated that the efficient electron transfer process from CdTe/CdS core-shell QDs to ZnO nanocrystals could be controlled by changing the CdTe core size on the basis of the quantum confinement effect.     

Investigation of populated InAs/GaAs quantum dots by photoluminescence and photoreflectance

We studied self-assembled InAs/GaAs quantum dots by contrasting photoluminescence and photoreflectance spectra from 10 K to room temperature. The photoluminescence spectral profiles comprise contributions from four equally separated energy levels of InAs quantum dots. The emission profiles involving ground state and excited states have different temperature evolution. Abnormal spectral narrowing occurred above 200 K. In the photoreflectance spectra, major features corresponding to the InAs wetting layer and GaAs layers were observed. Temperature dependences of spectral intensities of these spectral features indicate that they originate from different photon-induced modulation mechanisms. Considering interband transitions of quantum dots were observed in photoluminescence spectra and those of wetting layer were observed in photoreflectance profiles, we propose that quantum dot states of the system are occupied up to the fourth energy level which is below the wetting layer quantum state.     

水溶性CdTe量子点的稳态和纳秒时间分辨光致发光光谱

报道了以飞秒脉冲激光为激发光源的水溶性CdTe量子点(QDs)的稳态荧光光谱和纳秒时间分辨荧光光谱.实验发现CdTe量子点的荧光光谱峰值位置随激发波长变化发生明显移动，激发脉冲波长越长，荧光峰位红移越大.荧光动力学实验数据显示，在400nm和800nm脉冲激光激发下，水溶性CdTe量子点的荧光光谱中均含有激子态和诱捕态两个衰减成分，两者的发射峰相距很近，诱捕态的发射峰波长较长.在800nm脉冲激光激发下的诱捕态成分占总荧光强度的比重比400nm激发下的约高3倍，其相对强度的这种变化导致了稳态荧光发射峰位的红移. 关键词： CdTe 量子点 时间分辨 荧光光谱 上转换荧光     

The third-order optical nonlinearity and upconversion luminescence of CdTe quantum dots under femtosecond laser excitation

The aqueous CdTe quantum dots (QDs) were synthesized by the electrostatic reaction method. The optical properties of CdTe QDs were investigated by femtosecond Z-scan and time-resolved luminescence technique in nonresonant spectral region. The nonlinear absorption and refraction are ascribed to two-photon absorption, and time-resolved upconversion photoluminescence produces biexponential decay pattern at infrared femtosecond laser excitation. Upconversion luminescence is composed of a band-edge excitonic state and a photoinduced trapping state. The short-lived band-edge excitonic emission is independent of the detection wavelengths, and long-lived species becomes even longer with the increase of detection wavelengths, which indicates the size dependence of surface excitonic emission. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Photoluminescence properties of a novel conjugate of water-soluble CdTe quantum dots to guanine

A novel conjugate of water-soluble CdTe quantum dots to a small biomolecule guanine has been obtained in aqueous phase. The photoluminescence property and the stability of the conjugate increased comparing to CdTe QDs. The interaction between CdTe QDs and guanine was studied by TEM, fluorescence microscope and photoluminescence (PL), IR, UV-Vis spectra. The effects of reflux time, pH value, ionic strength, and the ratio of CdTe QDs to guanine on the photoluminescence properties of conjugate were investigated in detail. The results show that guanine has a great influence on both the photoluminescence property and stability of thioglycolic acid-stabilized CdTe QDs. The formation of coordination and hydrogen bond between guanine molecules and CdTe including thioglycolic acid on its surface may effectively enhance the PL intensity and stability of CdTe QDs. The maximum PL intensity of the conjugate was obtained on the condition with lower ionic strength, less than 30 min reflux time, neutral pH value and 6/1 as molar ratio of guanine to CdTe.     

Optical characterization of individual quantum dots

Optical characterization of single quantum dots (QDs) by means of micro-photoluminescence (μPL) will be reviewed. Both QDs formed in the Stranski–Krastanov mode as well as dots in the apex of pyramidal structures will be presented. For InGaAs/GaAs dots, several excitonic features with different charge states will be demonstrated. By varying the magnitude of an external electric or magnetic field and/or the temperature, it has been demonstrated that the transportation of carriers is affected and accordingly the charge state of a single QD can be tuned. In addition, we have shown that the charge state of the QD can be controlled also by pure optical means, i.e. by altering the photo excitation conditions. Based on the experience of the developed InAs/GaAs QD system, similar methods have been applied on the InGaN/GaN QD system.     

Aqueous synthesis of thiol-capped CdTe quantum dots and its photoluminescence enhancement via room temperature treatment with alkyl chain diamines

In this study the CdTe quantum dots (QDs) are synthesized in aqueous solution with three thiol-contained capping ligands of thioglycollic acid (TGA), 3-mercaptopropionic acid (MPA), and l-cysteine (lCys). The photoluminescence (PL) enhancement of the as-prepared QDs is also conducted via room temperature treatment with alkyl chain diamines. Our measurements on the ultraviolet–visible (UV–vis) absorption and fluorescence emission reveal that both the growth kinetics and the PL efficiency of the QDs vary a lot with the molecular structures of the three involved ligands. In comparison with TGA and lCys, MPA endows the QDs with a wide color tuning range from cyan to deep red and strong PL emission while its full width at half maximum (FWHM) is regretfully large. Notable enhancement on PL emission is achieved for the TGA and MPA capped QDs via room temperature treatment with diamines solutions while in the case of the QDs capped by lCys the enhancement is practically meaningless.     

Pressure-dependent photoluminescence of CdSe/ZnS quantum dots: Critical point of different pressure regimes

High pressure condition can alter and control the electronic structure of semiconductor quantum dots, and therefore provides novel insight for designing optoelectronic devices. Here we report the pressure-dependent photoluminescence (PL) of CdSe/ZnS core/shell quantum dots (QD) in different pressure regimes. The center of the PL spectrum has blue-shift when hydrostatic pressure increases, due to the increasing bulk modulus. However, the shifting rate becomes lower in the higher pressure regime, i.e. above the critical pressure point, mainly due to the interaction between QDs. Accordingly, the lifetimes of PL drop in the low pressure regime, due to the increased pressure-induced trapping states, then increase above the critical pressure point, indicating the interaction between dots likewise. The observed critical pressures for both cases are consistent with each other, and strongly depend on the QD concentration, which forcefully support the aforementioned interaction model.     

The influence of a continuum background on photoluminescence of self-assembled InAlAs/AlGaAs quantum dots

We have investigated the effect of the low energy tail of the continuum states associated with wetting layers (WL tail) on temperature dependence of the photoluminescence (PL) spectra of self-assembled InAlAs/AlGaAs quantum dots. We have developed a model that studies this effect. The results of this model suggest that the WL tail play an important role in the evolution according to the temperature of the PL spectra. We have also estimated that the capture into the QD ground state is via the WL tail.     

Preparation of water-soluble CdTe/CdS core/shell quantum dots with enhanced photostability

CdTe/CdS core/shell quantum dots (QDs) have been synthesized in an aqueous phase using thioacetamide as a sulfur source. The quantum yield was greatly enhanced by the epitaxial growth of a CdS shell, which was confirmed by X-ray photoelectron spectroscopy (XPS) results. The quantum yield of as-prepared CdTe/CdS core/shell QDs without any post-preparative processing reached 58%. The experimental results illustrate that the QDs with core/shell structure show better photostability than thioglycolic acid (TGA)-capped CdTe QDs. The cyclic voltammograms reveal higher oxidation potentials for CdTe/CdS core/shell QDs than for TGA-capped CdTe QDs, which explains the superior photostability of QDs with a core/shell structure. This enhanced photostability makes these QDs with core/shell structure more suitable for bio-labeling and imaging.     

Luminescence of CsPbBr3-like quantum dots in CsBr single crystals

Luminescence and decay kinetics of the Pb²⁺ aggregates in CsBr host crystals were measured in the 4–300 K temperature interval and in 10⁻¹⁰–10⁻³ time scale. Their emission properties are similar to those of CsPbBr₃ bulk crystal showing a subnanosecond free exciton emission in the 520–540 nm spectral region and slower trapped exciton emission in the 530–580 nm spectral region. An efficient energy exchange between the free and trapped exciton states is shown by the temperature dependencies of emission spectra. The quantum size effect is demonstrated in the high energy shift and broadening of the absorption and emission spectra and an estimate of the size of the CsPbBr₃-like aggregates is provided. Independent evidence of the presence of the CsPbBr₃ and Cs₄PbBr₆ aggregated phases in the CsBr host was obtained by X-ray structural studies.     

Synthesis and photoluminescence properties of aqueous CdWO4 quantum dots with WO6 luminescence center

Aqueous CdWO₄ QDs were synthesized by the reaction of CdCl₂ and Na₂WO₄ in the presence of mercaptoacetic acid (TGA) as capping reagent. The crystal morphology, particle size and its distribution of as-prepared products were characterized by transmission electron microscopy (TEM, SAED) atomic force microscopy (AFM), high-resolution transmission electron microscopy (HRTEM), and photon correlation spectroscopy (PCS), respectively. Qualitative assays for functional groups on the QDs’ surface were measured by fourier transform infrared spectroscopy (FTIR). Photoluminescence properties of QDs were studied by photoluminescence spectroscopy (PL). The results showed that the single QD with diameter of about 8 ± 2 nm was single-crystal. The particle size distribution of QDs was normal. Infrared absorption bands of carboxylic group on the surface of CdWO₄ QDs were observed around 1610-1550 cm⁻¹ (nonsymmetrical vibration of -COO⁻) and 1400 cm⁻¹ (symmetric vibration of C-O). With reaction-time going, PL peak position shifted from 498 to 549 nm and intensity of PL increased first and then decreased. PL peak position of QDs was blue-shift compared with 570 nm WO₆⁶⁻ luminescence center of bulk CdWO₄.     

One-pot synthesis of carbon dots co-doped with N and S: high quantum yield governed by molecular state and fluorescence detection of Ag+

Fluorescent carbon-based nanoparticles, called chronically as carbon dots (CDs), were synthesised from citric acid (CA) and 2-Aminothiophenol (2AT) via an N and S co-doped hydrothermal method. After a series of micro-structural characterisation, N and S elements could be sufficiently doped by means of the heteroatom in the CDs solution. The as-prepared CDs solution showed blue colour fluorescence with the highest QY of 78.6%, and study on the UV–visible and PL spectra further revealed that the outstanding fluorescence of as-prepared CDs mainly originates from the generated molecular fluorophores instead of the surface state. Owing to the strong fluorescence, the as-prepared CDs can be used as a sensing probe for the detection of Ag⁺ with high sensitivity and selectivity. However, the changes of fluorescence intensity exhibited the complex nature of the quenching mechanism due to the –SH and –NH₂ groups on the fringes of carbonaceous cores or molecular fluorophores to aggregate into another fluorescent cores with the assistance of Ag⁺ ions, which promises a new approach for efficient detection of Ag⁺ for the application in industrial pollutants.

This figure shows citric acid (CA) and 2-Aminothiophenol (2AT) via an N and S co-doped hydrothermal method to prepare CDs with blue colour fluorescence and the highest QY of 78.6%. Owing to the excellent fluorescence, the as-prepared CDs can be used as a sensing probe for the detection of Ag⁺ with high sensitivity and selectivity, and the changes of fluorescence intensity exhibited the complex nature of the quenching mechanism due to the –SH and –NH₂ groups on the fringes of carbonaceous cores or molecular fluorophores to aggregate into another fluorescent cores with the assistance of Ag⁺ ions, which promises a new approach for efficient detection of Ag⁺ for the application in industrial pollutants.     

Electroluminescence of colloidal ZnSe quantum dots

The article reports a green chemical synthesis of colloidal ZnSe quantum dots at a moderate temperature. The prepared colloid sample is characterised by UV-vis absorption spectroscopy and transmission electron microscopy. UV-vis spectroscopy reveals as-expected blue-shift with strong absorption edge at 400 nm and micrographs show a non-uniform size distribution of ZnSe quantum dots in the range 1-4 nm. Further, photoluminescence and electroluminescence spectroscopies are carried out to study optical emission. Each of the spectroscopies reveals two emission peaks, indicating band-to-band transition and defect related transition. From the luminescence studies, it can be inferred that the recombination of electrons and holes resulting from interband transition causes violet emission and the recombination of a photon generated hole with a charged state of Zn-vacancy gives blue emission. Meanwhile electroluminescence study suggests the application of ZnSe quantum dots as an efficient light emitting device with the advantage of colour tuning (violet-blue-violet).     

Inversion of the exciton fine structure splitting in quantum dots

The fine structure splitting of exciton state was measured for a large number of single InAs quantum dots in GaAs. It is shown to decrease as the exciton confinement decreases, crucially passing through zero and changing sign. Degeneracy of the exciton spin states is an important step to producing entangled photons from the biexciton cascade. Thermal annealing reduces the exciton confinement and thereby increases the number of degenerate dots in a particular sample.     

Temperature-dependent photoluminescence of vertically stacked self-assembled CdSe quantum dots in ZnSe

We studied the optical properties of multiple layers of self-assembled CdSe quantum dots (QDs) embedded in ZnSe, grown by molecular beam epitaxy. The ZnSe barrier thicknesses separating the QD layers ranged from 30 to 60 monolayers (ML). For stacks with thinnest ZnSe barriers photoluminescence (PL) measurements reveal blue shifts as large as 180 meV relative to PL observed for single QD layers. The amount of blue shift decreases with increasing barrier thickness, and for the 60 ML spacer the PL energy returns to that emitted by a single layer of QDs. Temperature dependence of the integrated intensity of the emission spectra reveals that the activation energy for PL quenching is largest for barrier thicknesses of 30 and 45 ML. We tentatively attribute these effects to a decrease in the size of the vertically stacked QDs when the thickness of the barrier layers is small.     

CdSSe quantum dots: effect of the hydrogen RF plasma treatment on exciton luminescence

This work deals with effective passivation of CdS_XSe_1−X quantum dot surface after treating it by low-temperature hydrogen RF plasma. An enhancement of the exciton luminescence was observed, which can be interpreted as consequence of a decreasing number of surface non-radiative traps.     

Investigation of the relation between photoluminescence intensity and decay time reduction with plasmon effect in InGaAs quantum dots

Plasmonic effects on photoluminescence are investigated via time-integrated and resolved photoluminescence (PL) in epitaxially grown InGaAs quantum dots (QDs). The decay time and PL intensities are compared as a function of the density of Ag nanoplates. Optimal conditions for both reduction lifetime and enhanced PL intensity were found to be a 1:15 ratio of Ag nanoplates to water. Both less and greater than that ratio 1:15, the lifetime increased and the enhancement factor of PL intensity decreased. In addition, the plasmon effect was investigated via resonance wavelength and temperature-dependent PL measurements. At 150K near the resonance conditions between PL from InGaAs QDs and Ag nanoplates, both the lifetime reduction and enhancement factor are maximized. Intensity enhancement is correlated to lifetime reduction for various conditions to identify a condition for maximized enhancement of radiative recombination for designing future ultrafast plasmonic nanolasers.