Variational analysis of Er:Ti:LiNbO3 waveguide lasers based on Gaussian/two-half Gaussian mode field distribution

Starting with two dimensional, scalar wave equation, a variational equation was established for the fundamental TE and TM modes guided in Ti:LiNbO₃ waveguides on the basis of assuming a symmetric Gaussian mode field function in the width direction and two-half Gaussian trial functions in the depth direction. The controllable waveguide fabrication parameters, including channel width, diffusion temperature, initial Ti-strip thickness and diffusion time, dependent of fundamental mode size, effective pump area, coupling efficiency between pump and laser modes, and the coupling loss between a Ti:LiNbO₃ waveguide and a fiber were numerically calculated for Z-cut Er:Ti:LiNbO₃ channel waveguide lasers at three possible emission wavelengths 1532,1563 and 1576 nm and two possible pump wavelengths 1480 and 980 nm. The calculated results were compared with those of Gaussian/Hermite–Gaussian mode field distribution in detail.     

Preparation and holographic storage properties of tri-doped Mg:Mn:Fe:LiNbO3 crystals

Doping MgO, MnO and Fe₂O₃ in LiNbO₃ crystals, tri-doped Mg:Mn:Fe:LiNbO₃ single crystals were prepared by the conventional Czochralski method. The UV-vis absorption spectra were measured and the shift mechanism of absorption edge was also investigated in this paper. In Mg:Mn:Fe:LiNbO₃ crystal, Mn and Fe locate at the deep level and the shallow level, respectively. The two-photon holographic storage is realized in Mg:Mn:Fe:LiNbO₃ crystals by using He-Ne laser as the light source and ultraviolet as the gating light. The results indicated that the recording time can be significantly reduced for introducing Mg²⁺ in the Mg:Mn:Fe:LiNbO₃ crystal.     

Lateral-field-excitation properties of LiNbO3 single crystal

LiNbO 3 has been found attractive for lateral field excitation (LFE) applications due to its high piezoelectric coupling. In this paper, bulk acoustic wave propagation properties for LiNbO 3 single crystal excited by a lateral electric field have been investigated using the extended Christoffel-Bechmann method. It is found that the LFE piezoelectric coupling factor for c mode reaches its maximum value of 95.46% when ψ = 0 for both (yxl)-58 and (yxwl)±60 /58 LiNbO 3 . The acoustic wave phase velocity of c mode TSM (thickness shear mode) changes from 3456 m/s to 3983 m/s as a function of ψ. Here ψ represents the angle between the lateral electric field and the crystallographic X-axis in the substrate major surface. A 5 MHz LFE device of (yxl)-58 LiNbO 3 with ψ = 0 was designed and tested in air. A major resonance peak was observed with the motional resistance as low as 17 and the Q-factor value up to 10353. The test result is well in agreement with the theoretical analysis, and suggests that the LFE LiNbO 3 device can be a good platform for high performance resonator or sensor applications.     

Study of near-infrared nonvolatile two-center holographic recording in LiNbO3:Fe:Rh crystal

The near-infrared nonvolatile holographic recording has been realized in a doubly doped LiNbO₃:Fe:Rh crystal by the traditional two-center holographic recording scheme, for the first time. The recording performance of this crystal has been investigated by recording with 633 nm red light, 752 nm red light and 799 nm near-infrared light and sensitizing with 405 nm purple light. The experimental results show that, co-doped with Fe and Rh, the near-infrared absorption and the photovoltaic coefficient of shallow trap Fe are enhanced in this LiNbO₃:Fe:Rh crystal, compared with other doubly doped LiNbO₃ crystals such as LiNbO₃:Fe:Mn. It is also found that the sensitizing light intensity affects the near-infrared recording sensitivity in a different way than two-center holographic recording with shorter wavelength, and the origin of experimental results is analyzed.     

Widely phase-matched tunable difference-frequency generation in periodically poled LiNbO3 crystal

We report on the development of a laser source in the mid-infrared spectral region based on difference-frequency generation (DFG) in a periodically poled LiNbO₃ (PPLN) crystal. Continuously tunable coherent radiation from 2.75 to 4.78 μm was produced by optical parametric interaction between a diode-pumped monolithic continuous-wave (CW) Nd:YAG laser operating at 1.064 μm and a CW Ti:Sapphire laser tunable from 767 to 871 nm. Temperature-dependent quasi-phase-matched DFG wavelength acceptance bandwidth was studied and characterized. An empiric formula is given to estimate the phase-matched wavelength acceptance bandwidth as a function of the crystal temperature at Λ = 22.5 μm. A large frequency scan of 128 cm⁻¹ (about 78 cm⁻¹ above 1 μW) near 4.2 μm was achieved. The whole absorption spectrum of the P and R branches of the ν₃ band of atmospheric carbon dioxide has been recorded with a single phase-matched frequency scan.     

Ultraviolet laser-induced photovoltaic effects in miscut ferroelectric LiNbO3 single crystals

This paper investigates the photovoltaic properties of miscut LiNbO 3 single crystal with different thicknesses under irradiation of a 248 nm ultraviolet laser pulse with 20 ns duration without an applied bias.Nanosecond photovoltaic response is observed and faster rise time is obtained in thinner samples.In accord with the 248 nm laser duration,the full width at half maximum of the photovoltaic signals keeps a constant of ～ 20 ns.With decrease of the crystal thickness,the photovoltaic sensitivity was improved rapidly at first and then decreased,and the maximum photovoltage occurred at 0.38 mm-thick single crystal.The present results demonstrate that decreasing the LiNbO3 single crystal thickness can obtain faster response time and improve the photovoltaic sensitivity.     

Nonvolatile photorefractive holographic recording in Sc:Ce:Cu:LiNbO3

In this paper experimental studies of nonvolatile photorefractive holographic recording in Ce:Cu:LiNbO₃ crystals doped with Sc(0,1,2,3 mol%) were carried out. The Sc:Ce:Cu:LiNbO₃ crystals were grown by the Czochralski method and oxidized in Nb₂O₅ powders. The nonvolatile holographic recording in Sc:Ce:Cu:LiNbO₃ crystals was realized by the two-photon fixed method. We found that the recording time of Sc:Ce:Cu:LiNbO₃ crystal became shorter with the increase of Sc doping concentration, especially doping with Sc(3 mol%), which exceeds the so-called threshold, and there was little loss of nonvolatile diffraction efficiencies between Sc(3 mol%):Ce:Cu:LiNbO₃ and Ce:Cu:LiNbO₃ crystals.     

周期极化掺镁不同组分LiNbO3晶体的研究

利用气相平衡扩散法研制出掺镁不同组分的LiNbO₃晶体，并对其极化特性进行了研究.研究表明晶体的开关电场和自发极化不仅与晶体组分［Li］/［Nb］比有关而且与掺镁量有关，［Li］/［Nb］比为0.973掺入2mol% MgO的近化学比LiNbO₃晶体的开关电场仅为1.8kV/mm，是同成分晶体的1/12，且其极化结构的质量要远好于同成分LiNbO₃晶体和近化学比LiNbO₃晶体. 关键词： 气相平衡扩散 3晶体')" href="#">掺镁LiNbO₃晶体 周期极化     

Investigation of quasi lateral-field-excitation on (yxl)-17° LiNbO3 single crystal

Quasi lateral-field-excitation (LFE) on LiNbO₃ crystal is investigated both theoretically and experimentally. It is found that when the driving electric field direction is parallel to the crystallographic X-axis of the piezoelectric substrate, (yxl)-17° LiNbO₃ LFE bulk acoustic wave devices work on quasi-LFE mode. The experimental results agreed with the theoretical prediction well. The results provide the cut of LiNbO₃ crystal for quasi-LFE bulk acoustic wave devices, which is important for designing high performance LFE sensors on LiNbO₃ substrates.     

Spectra and intensity parameters of Tm ion in YAlO3 crystal

High quality Tm-doped YAlO₃ (Tm:YAlO₃) single crystals were obtained along crystallographic b-axis by the Czochralski technique. Optical absorption and fluorescence spectra for Tm³⁺ in YAlO₃ crystals were investigated at room temperature. Based on Judd-Ofelt approach, the intensity parameters Ω_t (t = 2, 4, 6) of Tm:YAlO₃ were calculated to be Ω₂ = 0.93 × 10⁻²⁰  cm², Ω₄ = 2.23 × 10⁻²⁰ cm², and Ω₆ = 1.12 × 10⁻²⁰ cm². The spectral parameters such as experimental and theoretical oscillator strengths, radiative transition probabilities, radiative lifetime and the fluorescence branching ratio were also obtained. All results indicate that Tm:YAlO₃ is a potential candidate for compact, efficient mid-infrared lasers with laser diode pumping.     

Effects of forming gas annealing on LiNbO3 single crystals

Z-cut congruent LiNbO₃ single crystals were annealed in 95%N₂+5%H₂ at high temperatures. X-ray diffraction showed that 2θ of (0 0 0 6) peak is obviously reduced by 0.6° and 1.0° for the samples annealed at 600 and 900 °C, respectively. A new peak appears at the high-energy side of O 1s spectrum in X-ray photoelelectron spectroscopy (XPS) analyses, and the leakage current is greatly increased. It is proposed that hydrogen is incorporated in LiNbO₃ single crystals through forming gas annealing at temperatures up to 900 °C and exists in LiNbO₃ as a proton bound to an oxygen ion through O-H bond with its electron donated.     

Structure and optical damage resistance of Zn:Mn:Fe:LiNbO3 crystals

The new non-volatile holographic storage materials, Zn:Mn:Fe:LiNbO₃ crystals, were prepared by Czochralski technique. Their microstructure was measured and analyzed by infrared (IR) transmission spectra. The optical damage resistance of Zn:Mn:Fe:LiNbO₃ crystals was characterized by the transmitted beam pattern distortion method. It increases remarkably when the concentration of ZnO is over a threshold concentration. Its value in Zn(7.0 mol%):Mn:Fe:LiNbO₃ crystal is about three orders of magnitude higher that in Mn:Fe:LiNbO₃ crystal. The photoinduced birefringence change was measured by the Sénarmont's method. It decreased with ZnO concentration increasing. The dependence of the defects on the optical damage resistance was discussed.     

掺镁铌酸锂亚微米结构畴反转的研究

研究了掺镁铌酸锂(MgO：LiNbO₃)的极化特性及其畴壁运动的性质,通过调节多个脉冲外加电场来控制畴壁的运动,在背向反转效应作用下,反转畴发生劈裂,制备出均匀的掺镁铌酸锂亚微米周期畴结构,并分析探讨了掺镁铌酸锂亚微米结构的成因及其反转机理. 关键词： 亚微米畴结构 掺镁铌酸锂 背向反转     

Investigation of nonvolatile holographic storage in LiNbO3:Mn:Ce:Fe crystal

We investigate the persistent holographic recording in triply doped LiNbO₃:Mn:Ce:Fe crystals at different oxidation/reduction states. The experimental results show that there is an optimum oxidation/reduction state, which results in the best dynamic range M/#. Compared with doubly doped LiNbO₃:Ce:Fe, we found that the nonvolatile diffraction efficiency and the best dynamic range M/# obtained in triply doped samples are larger than that obtained in doubly doped samples. The reason for the increase of the crystal about the nonvolatile diffraction efficiency and the dynamic range M/# was also explained.     

Growth and optical properties of Mg, Fe Co-doped LiTaO3 crystal

Mg, Fe double-doped LiTaO₃ and LiNbO₃ crystals have been grown by Czochralski method. The optical properties were measured by two-beam coupling experiments and transmitted facula distortion method. The results showed that the photorefractive response speed of Mg:Fe:LiTaO₃ was about three times faster than that of Fe:LiTaO₃, whereas the photo-damage resistance was two orders of magnitude higher than that of Fe:LiTaO₃. In this paper, site occupation mechanism of impurities was also discussed to explain the high photo-damage resistance and fast response speed in Mg:Fe:LiTaO₃ crystal.     

Growth and spectroscopic characterization of Er: Sr3Y(BO3)3 crystal

This paper reports the growth and spectroscopic characterization of Er³⁺:Sr₃Y(BO₃)₃ crystal. Er³⁺:Sr₃Y(BO₃)₃ crystal with dimensions up to ∅20×35 mm³ has been grown by Czochralski method. The polarized spectroscopic properties of Er³⁺:Sr₃Y(BO₃)₃ crystal were investigated. Based on the Judd-Ofelt theory, the effective intensity parameters Ω_t were obtained: Ω₂=1.71×10⁻²⁰ cm², Ω₄=1.39×10⁻²⁰ cm², Ω₆=0.74×10⁻²⁰ cm² for π-polarization, and Ω₂=1.77×10⁻²⁰ cm², Ω₄=1.44×10⁻²⁰ cm², Ω₆=0.65×10⁻²⁰ cm² for σ-polarization. The emission cross-section σ_em was calculated to be 4.75×10⁻²¹ cm² for π-polarization at 1536 nm and 6.30×10⁻²¹ cm² for σ-polarization at 1537 nm. The investigated results showed that Er³⁺:Sr₃Y(BO₃)₃ crystal may be regarded as a potential laser host material for 1.55 μm IR solid-state lasers.     

White light interferometry test and analysis of LiNbO3 polarizer

White light interferometer can be used to measure the amplitude extinction ratio (ER) of polarizer and coupling distribution in fiber. A LiNbO₃ polarizer coupled with a polarization maintaining fiber and a silica planar waveguide at the two ends was measured using white light interferometer. According to the principles of optical coherence domain polarimeter (OCDP) technique, the test scheme is analyzed and presented to measure the ER of LiNbO₃ polarizer with its apparatus proposed correspondingly. By analyzing the interference intensity, both the ER of LiNbO₃ polarizer and its coupling crosstalk with optical fiber and waveguide are obtained. The results illustrate that the ER of a 5 mm-long LiNbO₃ polarizer is 71 dB and the crosstalk of the coupling points are around 40 dB. The results have good agreement with analysis.     

Spectroscopic investigations and configuration-interaction-assisted crystal field analysis of Pr in YPO4 single crystal

An optical study of a Y_0.99Pr_0.01PO₄ single crystal is presented. Measurements of optical absorption, excitation, and emission by selective excitation into ¹D₂, ³P₀ and ³P₁, at different temperatures between 20 and 295 K, are described. A detailed account of the line assignments is given for absorption in the 4300-23 000 cm⁻¹ spectral range, and for emission in the 6400-23 000 cm⁻¹ range. The lifetimes of the emitting levels are determined. Vibronic sidebands accompanying absorption, emission and excitation spectra are reported. The decay processes of the ³P₁, ³P₀ and ¹D₂ levels are discussed. The aim of this study is a test of the configuration-interaction-assisted crystal field analysis as well as the accurate experimental determination of the energy level scheme. It was reported previously that the introduction of configuration interaction between the ground 4f² configuration with the excited 4f6p configuration always resulted in a decrease (≈50-60%) in the standard deviations between the observed and calculated energy levels. In the present work the 4f5d configuration is included as well. The crystal field is analysed in the theoretical D_2d site symmetry with and without configuration interaction. The results with 4f², 4f²+4f5d, 4f²+4f6p and 4f²+4f5d+4f6p are given. The calculation on the basis of the 315 (4f²+4f5d+4f6p) levels gives the best overall standard deviation lowering it by 75% with regard to the calculation on the 91 4f² levels only.     

Forced oscillator model of dynamic spatial charge field in the reduced Zn:Fe:LiNbO3 crystal

Holographic data storage is promised to be the next-generation optical storage technology for many years. The Zn:Fe:LiNbO₃ crystal is studied widely because of its promising holographic storage properties. The forced oscillator model is used to explain the self-erasing phenomenon in the reduced Zn:Fe:LiNbO₃ crystals. It is showed that the total spatial charge field is dominated by two kinds of carrier with different respond time, which are electron and hole, respectively. The cooperative action of two kinds carrier induces that the total charge field non-monotonically varies with the recording time. The same diffraction efficiency of hologram with equal exposure energy is realized by the self-erasing property. The precision of the optical correlation recognition based on holographic storage will be improved.     

Morphology of ablation craters generated by fs laser pulses in LiNbO3

The surface morphology of the ablation craters generated in LiNbO₃ by 130 fs laser pulses at 800 nm has been investigated by AFM/SNOM microscopy. The single pulse fluence corresponding to the ablation threshold has been estimated to be ≈1.8 J/cm².A complex structure including random cone-shaped protrusions is observed inside the ablated crater. The scale of the protrusion spacing is in the submicron range and the heights are typically of a few tens of nanometers. At and outside the crater rim a novel quasi-periodic wave-like topography pattern is observed in both types of microscopy techniques. The average wavelength, that is slightly dependent on pulse fluence, is (500-800 nm) comparable to the light wavelength. This novel topography feature keeps a close similarity with a Fresnel diffraction pattern by an absorbing circular obstacle or impact wave pattern produced by a combination of heat and shock wave (resemble that of impact crater). It is proposed that the obstacle is associated to the strongly nonlinear multiphoton absorption at the peak of the pulse profile. The energy deposited by nonlinear absorption of such profile causes ablation of both the crater and the rippled structure.