High efficiency rubrene based inverted top-emission organic light emitting devices with a mixed single layer

Inverted top-emission organic light emitting devices (TEOLEDs) with a mixed single layer by mixing of electron transport materials (PyPySPyPy and Alq₃), hole transport material (α-NPD) and dope material (rubrene) were investigated. Maximum power efficiency of 3.5 lm/W and maximum luminance of 7000 cd/m² were obtained by optimizing the mixing ratio of PyPySPyPy:Alq₃:α-NPD:rubrene=25:50:25:1. Luminance and power efficiency of mixed single layer device were two times improved compared to bi-layer heterojunction device and tri-layer heterojunction device. Lifetime test also shows that the mixed single layer device exhibits longer operational lifetimes of 343 h, which is three times longer than the 109 h for tri-layer device, and two times longer than the 158 h for bi-layer device. In addition, the maximum luminance and power efficiency were obtained at 20,000 cd/m² and 7.5 lm/W, respectively, when a TPD layer of 45 nm was capped onto the top metal electrode.     

Highly efficient and bright doped organic electroluminescent diodes using an aluminum electrode

Remarkable improvement in efficiency and electroluminescence (EL) has been observed in an organic EL device, which consists of a hole-transport layer and a luminescent layer. The hole-transport layer is an N,N-bis(3-methyphenyl)-N,N-diphenylbenzidine film. The doped emitting layer consists of 8-(quinolinolate)-aluminum as the host and rubrene as the emission dopant. The doped cell with aluminum cathode demonstrated a luminance in excess of 20,000 cd/m² and an external quantum efficiency of 2.7%, which is about four times and three times, respectively, greater than those of the undoped cell. The EL emission from the device shows spectral narrowing and a shift to higher energy.     

Solution-processed white organic light-emitting devices based on small-molecule materials

We investigated solution-processed films of 4,4′-bis(2,2-diphenylvinyl)-1,1′-bibenyl (DPVBi) and its blends with N,N′-bis(3-methylphenyl)-(1,1′-biphenyl)-4,4′-diamine (TPD) by atomic force microscopy (AFM). The AFM result shows that the solution-processed films are pin-free and their morphology is smooth enough to be used in OLEDs. We have developed a solution-processed white organic light-emitting device (WOLEDs) based on small-molecules, in which the light-emitting layer (EML) was formed by spin-coating the solution of small-molecules on top of the solution-processed hole-transporting layer. This WOLEDs, in which the EML consists of co-host (DPVBi and TPD), the blue dopant (4,4′-bis[2-(4-(N,N-diphenylamino)phenyl)vinyl]biphenyl) and the yellow dye (5,6,11,12-tetraphenylnaphtacene), has a current efficiency of 6.0 cd/A at a practical luminance of 1000 cd/m², a maximum luminance of 22500 cd/m², and its color coordinates are quite stable. Our research shows a possible approach to achieve efficient and low-cost small-molecule-based WOLEDs, which avoids the complexities of the co-evaporation process of multiple dopants and host materials in vacuum depositions.     

Highly efficient greenish blue-emitting organic diodes based on pyrene derivatives

We report the synthesis of pyrene derivatives as the light emissive layer for highly efficient organic electroluminescence (EL) diodes. Multilayer devices were fabricated with pyrene derivatives (ITO/NPB (50 nm)/blue material (30 nm)/BCP (10 nm)/Alq₃ (30 nm)/LiF (1 nm)/Al). By using 1,1′-dipyrene (DP) and 1,4-dipyrenyl benzene (DPB), the devices produced the blue EL emissions with 1931 Commission International de L’Eclairage coordinates of (x=0.21, y=0.35) and (x=0.19, y=0.25), respectively. The device with DPB shows a maximum brightness of 42,445 cd/m² at 400 mA/cm² and the luminance efficiency of 8.57 cd/A and 5.18 lm/W at 20 mA/cm².     

Efficient small molecular and polymer organic devices using bis[2-(4-tert-butylphenyl)benzothiazolato-N,C′] iridium (III) (acetylacetonate) dye as emitter

Small molecular organic light-emitting diodes (MOLED) and polymer organic light-emitting diodes (POLED) were fabricated with yellow light emission phosphorescent dye bis[2-(4-tert-butylphenyl)benzothiazolato-N,C²′] iridium (III) (acetylacetonate) doped in different hosts. The electroluminescent (EL) spectra of both devices shown two peaks generated from iridium dye but the position of main peak changed and became broader for POLED. The maximum luminance of 10,500 cd/m² achieved at 12.5 V for MOLED is higher than maximum luminance of 9996 cd/m² at 20 V for POLED. The maximum power efficiency of small molecular device is 6.4 lm/W, which is higher than 2.3 lm/W of polymer device, but the efficiency of both devices will roll off at large current density.     

Nondoped phosphorescent organic quantum well light-emitting device based on iridium complex: Synthesis, characterization, photophysical property, and electroluminescence performance

In this paper, we report a phosphorescent Ir(III) emitter of Ir(acac)(F-BT)₂, where acac=acetylacetonate and F-BT=2-(2-fluorophenyl)benzo[d]thiazole, including its crystal structure, electronic nature, photophysical characteristics, thermal, and electrochemical properties. Data suggest that Ir(acac)(F-BT)₂ is a promising emitter with high quantum yield of 0.61 and good thermal stability, along with its proper energy levels for charge carrier transportation. Multiple quantum well (MQW) structured OLEDs using Ir(acac)(F-BT)₂ as emitter are also fabricated, and their electroluminescence (EL) are investigated in detail. The optimal EL device with 4,4′-N,N′-dicarbazole-biphenyl as potential well layer shows a maximum luminance of 85,500 cd/cm² and a peak current efficiency of 31.5 cd/A, and the efficiency roll-off is efficiently reduced.     

Blue organic electroluminescent devices based on a distyrylarylene derivative as emitting layer and a terbium complex as electron-transporting layer

With a blue distyrylarylene derivative, 4,4′-bis(2,2-di(2-methoxyphenyl)ethenyl)-1,1′-biphenyl (CBS) as emitting material, double-layer and triple-layer electroluminescent (EL) devices were fabricated. For the device using tris-(1-phenyl-3-methyl-4-isobutyryl-5-pyrozolone)-bis(triphenyl phosphine oxide) terbium (Tb(PMIP)₃(TPPO)₂) as the electron-transporting layer, blue EL emission with a maximum luminance of 253 cd/m² was achieved at 19 V. The difference of Tb(PMIP)₃(TPPO)₂ and tris(8-hydroxyquinolinate)aluminum (AlQ) as the electron-transporting materials in these devices were compared and discussed.     

Improved performance and stability by an Al/Ni bilayer cathode in organic light-emitting diodes

Al/Ni bilayer cathode was used to improve the electroluminescent (EL) efficiency and stability in N,N′-bis(1-naphthyl)-N,N′-diphenyl-1,1′ biphenyl 4,4′-dimaine (NPB)/tris-(8-hydroxyquinoline) aluminum (Alq₃)-based organic light-emitting diodes. The device with LiF/Al/Ni cathode achieved a maximum power efficiency of 2.8 lm/W at current density of 1.2 mA/cm², which is 1.4 times the efficiency of device with the state-of-the-art LiF/Al cathode. Importantly, the device stability was significantly enhanced due to the utilization of LiF/Al/Ni cathode. The lifetime at 30% decay in luminance for LiF/Al/Ni cathode was extrapolated to 400 h at an initial luminance of 100 cd/m², which is 10 times better than the LiF/Al cathode.     

Increased luminance of MEH-PPV and PFO based PLEDs by using salmon DNA as an electron blocking layer

The effect of salmon DNA-CTMA as an electron blocking layer (EBL) has been examined on the performance of MEH-PPV and PFO-based light emitting diodes. Though the turn-on voltage increases with incorporation of EBL, a significant increase in luminance and luminous efficiency for both the devices is observed. The EBL improves the device performance by blocking electrons at the EBL-polymer interface, thereby increasing the recombination probability of electrons and holes. The luminance of the MEH-PPV based Bio-LED increases to 100 cd/m² from 30 cd/m² while a corresponding increase for the PFO based LED is to 160 cd/m² from 80 cd/m² with and without EBL, respectively.     

White organic electroluminescence from fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc doped with phosphorescent material

Efficient white electroluminescence has been obtained by using an electroluminescent layer comprising of a blue fluorescent bis (2-(2-hydroxyphenyl) benzoxazolate)zinc [Zn(hpb)₂] doped with red phosphorescent bis (2-(2′-benzothienyl) pyridinato-N,C^3′)iridium(acetylacetonate) [Ir(btp)₂acac] molecules. The color coordinates of the white emission spectrum was controlled by optimizing the concentration of red dopant in the blue fluorescent emissive layer. Organic light-emitting diodes were fabricated in the configuration ITO/α-NPD/Zn(hpb)₂:0.01 wt%Ir(btp)₂acac/BCP/Alq₃/LiF/Al. The J-V-L characteristic of the device shows a turn on voltage of 5 V. The electroluminescence (EL) spectra of the device cover a wide range of visible region of the electromagnetic spectrum with three peaks around 450, 485 and 610 nm. A maximum white luminance of 3500 cd/m² with CIE coordinates of (x, y=0.34, 0.27) at 15 V has been achieved. The maximum current efficiency and power efficiency of the device was 5.2 cd/A and 1.43 lm/W respectively at 11.5 V.     

Synthesis and electroluminescent properties of a carbozole-functionalized europium(III) complex

A novel europium(III) complex, tris(dibenzoylmethanate){1-[9-hexyl-9H-carbazole]-2-(2-pyridyl)-benzimidazole}europium(III) [Eu(DBM)₃(CAR-PyBM)] functionalized by a carbozole fragment, was synthesized and used as emitting material in organic electroluminescent (EL) devices. Compared with the device based on an unfunctional Eu(III) complex, [Eu(DBM)₃HPyBM] (HPyBM=2-(2-pyridyl)benzimidazole), the EL performances of the device using [Eu(DBM)₃(CAR-PyBM)] as an emitter was significantly enhanced due to the improvement of hole-transporting ability. The maximum efficiency and luminance of red emission achieved from the device with the configuration of ITO/N,N′-diphenyl-N,N′-bis(3-methylphenyl)-1,1′-biphenyl-4,4′diamine (TPD, 50 nm)/ [Eu(DBM)₃(CAR-PyBM)] (30 nm)/1,3,5-tirs-(N-phenylbenzimidazol-2-yl)benzene (TPBI, 20 nm)/LiF (1.5 nm)/Al were 4.2 cd/A and 200 cd/m², respectively.     

Characterization of two-emitter WOLED with no additional blocking layer

In this paper, white organic light emitting diodes (WOLEDs) utilizing two primary-color emitters with no additional blocking layer are fabricated. With a structure of ITO/2TNATA (20 nm)/NPB (20 nm)/NPB: rubrene (2%) (10 nm)/ADN (30 nm)/Alq₃ (20 nm)/LiF (1 nm)/Al (100 nm), a white light with CIE coordinates of (0.344, 0.372) is generated at a current density of 30 mA/cm² and the electroluminescence (EL) spectra consist of two broad bands around 456 nm (ADN) and 556 nm (NPB:rubrene). The device shows the low turn-on voltage and bright white emission with a power efficiency of 2.3 lm/W at a luminance of 100 cd/m². Through control of the location of the recombination zone and energy transfer, a stable white light emission is achieved. The maximum color shift is less than 0.02 units on the 1931 CIE x,y chromaticity diagram. Given the spectral power distribution of WOLED, the parameters of a light source (chromaticity coordinate, CCT, CRI, and the luminous efficacy) can be calculated. A MATLAB program for this purpose is developed in this paper. Based on this, the design of WOLED for an illumination and display system using a white emitter with color filter arrays is discussed.     

Photoluminescence and electroluminescence of a novel green-yellow emitting material-5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile

A new compound with intramolecular charge transfer (ICT) property—5,6-Bis-[4-(naphthalene-1-yl-phenyl-amino)-phenyl]-pyrazine-2,3-dicarbonitrile(BNPPDC) was synthesized. The new compound was strongly fluorescent in non-polar and moderately polar solvents, as well as in thin solid film. The absorption and emission maxima shifted to longer wavelength with increasing solvent polarity. The fluorescence quantum yield also increased with increasing solvent polarity from non-polar to moderately polar solvents, then decreased with further increase of solvent polarity. This indicates both “positive” and “negative” solvatokinetic effects co-existed. Using this material as hole-transporting emitter and host emitter, we fabricated two electroluminescent (EL) devices with structures of A (ITO/BNPPDC (45 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm) and B (ITO/N,N′-diphenyl-N,N′-bis-(3-methylphenyl) (1,1′-diphenyl)4,4′-diamine (TPD) (50 nm)/BNPPDC (20 nm)/1,3,5-tris(N-phenylbenzimidazol-2-yl)benzene (TPBI) (45 nm)/Mg:Ag (200 nm). The devices showed green-yellow EL emission with good efficiency and high brightness. For example, the device A exhibited a high brightness of 17400 cd/m² at a driving voltage of 11 V and a very low turn-on voltage (2.9 V), as well as a maximum luminous efficiency 3.61 cd/A. The device B showed a similar performance with a high brightness of 12650 cd/m² at a driving voltage of 13 V and a maximum luminous efficiency 3.62 cd/A. In addition, the EL devices using BNPPDC as a host and 4-(dicyanomethylene)-2-t-butyl-6-(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) as a dopant (configuration: ITO/TPD (60 nm)/BNPPDC:DCJTB (2%) (30 nm)/TPBI (35 nm)/Mg:Ag (200 nm)) showed a good performance with a brightness of 150 cd/m² at 4.5 V, a maximum brightness of 12600 cd/m² at 11.5 V, and a maximum luminous efficiency of 3.30 cd/A.     

Non-doped phosphorescent white organic light-emitting devices with a quadruple-quantum-well structure

Non-doped white organic light-emitting devices (WOLEDs) with a quadruple-quantum-well structure were fabricated. An alternate layer of ultrathin blue and yellow iridium complexes was employed as the potential well layer, while potential barrier layers (PBLs) were chosen to be 2,2',2''-(1,3,5-benzenetriyl)-tris(1-phenyl-1-H-benzimidazole) (TPBi) or N,N'-dicarbazolyl-3,5-benzene (mCP) combined TPBi. On adjusting the PBLs for device performance comparison, the results showed that the device with all-TPBi PBLs exhibited a yellow emission with the color coordinates of (0.50,0.47) at a luminance of 1000 cd/m², while stable white emission with the color coordinates of (0.36,0.44) was observed in the device using mCP combined TPBi as the PBLs. Meanwhile, for the WOLED, with a reduced efficiency roll-off, a maximum luminance, luminous efficiency, and external quantum efficiency of 12,610 cd/m², 10.2 cd/A, and 4.4%, respectively, were achieved. The performance improvement by the introduction of mCP PBL was ascribed to the well confined exciton and the reduced exciton quenching effect in the multiple emission regions.     

Excited state complex and electroluminescence in TPD-based single layer device

N-N′-diphenyl-N,N′-(bis(3-methylphenyl)-1,1′-biphenyl-4,4′-diamine) (TPD), was used to fabricate single layer devices (ITO/TPD/Ca/Al). A near-white emission (CIE coordinate of 0.25, 0.24) is observed in electroluminescence (EL) of the single layer device with prominent emission bands at 400, 475 and 670 nm. Steady state and time-resolved emission spectra of spin-coated and annealed TPD films and TRES and TRANES analysis confirmed that emission at 400 and 475 nm are due to monomer and excimer emission, respectively. The origin of the red emission at 670 nm in EL is discussed.     

High-efficiency Simple Structure White Organic Light-emitting Devices Based on Rubrene Ultrathin Layer

White organic light-emitting devices (WOLEDs) were fabricated with an ultrathin layer of rubrene inserted between NPB and TPBI. With a simple three-layer structure of ITO/NPB(50 nm)/rubrene(0.1 nm)/TPBI(50 nm)/LiF/Al, a white light with CIE coordinates of (0.31, 0.30) were generated. The device gave a maximum luminance efficiency of 2.04 lm/W at 5 V. Furthermore, with a multilayer structure of ITO/m-MTDATA(30 nm)/NPB(20 nm)/rubrene(0.1 nm)/TPBI(40 nm)/Alq₃(10 nm)/LiF/Al, the device reached a maximum luminance efficiency of 4.29 lm/W at 4 V and the luminance could exceed 10 000 cd/m² at 10 V.     

Efficient polymer white-light-emitting diodes with a single-emission layer of fluorescent polymer blend

Efficient polymer white-light-emitting diodes (WPLEDs) have been fabricated with a single layer of fluorescent polymer blend. The device structure consists of ITO/PEDOT/PVK/emissive layer/Ba/Al. The emissive layer is a blend of poly(9,9-dioctylfluorene) (PFO), phenyl-substituted PPV derivative (P-PPV) and a copolymer of 9,9-dioctylfluorene and 4,7-di(4-hexylthien-2-yl)-2,1,3-benzothiadiazole (PFO-DHTBT), which, respectively, emits blue, green and red light. The emission of pure and efficient white light was implemented by tuning the blend weight ratio of PFO: P-PPV: PFO-DHTBT to 96:4:0.4. The maximum current efficiency and luminance are, respectively, 7.6 cd/A at 6.7 V and 11930 cd/m² at 11.2 V. The CIE coordinates of white-light emission were stable with the drive voltages.     

Improved performances of the organic light-emitting devices by doping in the mixed layer

The brightness, efficiency and lifetime of organic light-emitting diodes (OLEDs) were remarkably improved by doping in a mixed layer. In this device, the emitting layer consists of a mixture of -naphthylphenybiphenyl amine (NPB), tris (8-hydroxyquinolinolate) aluminum (Alq₃) (referred to as the mixed layer) and an emissive dopant 5,6,11,12-petraphenylnaphthacene (rubrene), where the concentration of NPB declined while the concentration of Alq₃ was increased gradually in the deposition process. The device exhibited a maximum emission of 49,300 cd/m² at a destroy voltage of 35 V and a maximum efficiency of 7.96 cd/A at 10 V, respectively. The efficiency improves twofold in comparison with the conventional doped devices. Meanwhile, the device exhibited superior operational stability with a half-life time of 1000 h at a starting luminance of 1000 cd/m² by a constant current driver.     

A comparative study of electrode effects on the electrical and luminescent characteristics of Alq3/TPD OLED: Improvements due to conductive polymer (PEDOT) anode

The performance of organic light emitting device (OLED) structures, based on identically fabricated Alq₃/TPD active regions, with various anode and cathode electrode structures are compared, and performance differences related to the different anode structure. The best performance was achieved with a conductive polymer, 3,4-polyethylenedioxythiopene-polystyrenesultonate (PEDOT), used as an anode layer, yielding a brightness of 1720 cd/m² at 25 V, a turn-on voltage of 3 V, and electroluminescence (EL) efficiency and external quantum efficiency of 8.2 cd/A and 2%, respectively, at a brightness of 100 cd/m² and 5 V. Compared to a baseline device (TPD/Alq₃/Al), PEDOT anodes substantially reduce the turn-on voltage and made current injection almost linear after turn-on, whiles devices incorporating a LiF and CuPc layers significantly improved device efficiency while slightly improving turn-on voltage and maintaining superlinear I-V injection. This is attributed to the reduced barrier at the organic-organic interface in PEDOT, the ‘ladder’ effect of stepping the band offset over several interfaces, and the favorable PEDOT film morphology. The benefit of the PEDOT anode is clearly seen in the improvement in device brightness and the high external quantum efficiency obtained.     

高效率和色稳定性的双超薄发光层的黄光有机电致发光器件

主要对rubrene黄光发光材料制作0.1nm厚度的超薄发光层的有机电致发光器件作了研究,并配合BCP空穴阻挡层探讨了对器件效率和色坐标稳定性的影响。双超薄rubrene发光层配合BCP空穴阻挡层的有机电致发光器件的性能得到了很好的改善,外加电压6V时,器件电流效率为6.35cd.A-1;外加电压10V时,器件发光亮度达到了7068cd.m-2。另外,在较大的外加电压驱动范围内,器件的色坐标一直保持在(0.49,0.49)。增加的发光效率和良好的色坐标稳定性主要是取决于空穴与电子的注入与输运平衡以及激子在超薄rubrene发光层中稳定性的复合平衡。