An easily-prepared impedance matched Josephson parametric amplifier

An impedance matched parametric amplifier (IMPA) with Josephson junctions is fabricated and characterized. A hybrid structure containing coplanar and strip structures is implemented to realize an impedance taper line and a plate capacitor in an LC nonlinear resonator based on Josephson junctions. The upper plate of the capacitor is isolated with SiN_x without grounding as well as the strips. Such easily-prepared designs greatly reduce the requirements for lithography alignment and precision, which makes the fabrication process more reliable. The experimental results show that in such IMPA a gain higher than 25 dB with a bandwidth of about 100 MHz can be obtained. This broadband amplifier operates close to the quantum limit. By adjusting the working point, a higher bandwidth of about 400 MHz can be obtained with a gain of about 17 dB.     

Fabrication and characterization of all-Nb lumped-element Josephson parametric amplifiers

Josephson parametric amplifiers (JPAs) with nearly quantum-limited noise performance have become indispensable devices for the measurements of superconducting quantum information. We have developed an all-Nb lumped-element flux-driven JPA operating in the three-wave mixing mode. Our Nb-based JPA comprises Nb/Al-AlO_x/Nb Josephson junctions, a parallel-plate capacitor with SiO₂ dielectric sandwiched between two Nb layers, a bottom coplanar waveguides layer, and a top Nb wiring layer. We experimentally demonstrate a 20 dB gain over a 190 MHz bandwidth, a mean 1 dB compression of -123 dBm, and near quantum-limited noise performance. This fabrication process can be further used to design impedance transformed parametric amplifiers for multiple-qubit readout.     

Fabrication of Josephson parameter amplifier and its applicationin squeezing vacuum fluctuations

Josephson parameter amplifier (JPA) is a microwave signal amplifier device with near-quantum-limit-noise performance. It has important applications in scientific research fields such as quantum computing and dark matter detection. This work reports the fabrication and characterization of broadband JPA devices and their applications in multi-qubit readout and squeezing of vacuum state. We use a process in which transmission lines and electrodes are made of niobium thin film and aluminum Josephson junctions are made by Dolan bridge technique. We believe this process is more convenient than the process we used previously. The whole production process adopts electron beam lithography technology to ensure high structural resolution. The test result shows that the gain value of the manufactured JPA can exceed 15 dB, and the amplification bandwidth is about 400 MHz. The noise temperature is about 400 mK at the working frequency of 6.2 GHz. The devices have been successfully used in experiments involving superconducting multi-qubit quantum processors. Furthermore, the device is applied to squeeze vacuum fluctuations and a squeezing level of 1.635 dB is achieved.     

Fabrication and characterization of ultra-low noise narrow and wide band Josephson parametric amplifiers

We have fabricated two types of lumped-element Josephson parameter amplifiers (JPAs) by using a multilayer micro-fabrication process involving wet etching of Al films. The first type is a narrow band JPA which shows typical gain above 14 dB in a bandwidth around 35 MHz. The second type is a wideband JPA which is coupled to an input 50 Ω transmission line via an impedance transformer that changes the impedance from about 15 Ω on the non-linear resonator side to 50 Ω on the input transmission line side. The wideband JPA could operate in a 200 MHz range with a gain higher than 14 dB. The amplifiers were used for superconducting qubit readout. The results showed that the signal to noise ratio and hence the readout fidelity were improved significantly.     

Einstein——Podolsky——Rosen entanglement in time-dependent periodic pumping non-degenerate optical parametric amplifier

The solution of the time-dependent periodic pumping non-degenerate optical parametric amplifier (NOPA) is derived when the pump depletion is considered both above and below thresholds. Based on this solution, the quantum fluctuation calculated shows that a high entanglement and a good squeezing degree of the parametric light beams are achieved near and above thresholds. We adopt two kinds of pump fields: (i) a continuously modulated pump with a sinusoidal envelope; (ii) a sequence of laser pulses with Gaussian envelopes. We analyse the time evolution of continuous variable entanglement by analytical and numerical calculations, and show that the periodic driven pumping also improves the degree of entanglement. The squeezing and Einstein-Podolsky-Rosen (EPR) entanglement by using the two pumping driven functions are investigated from below to above the threshold regions, the tendencies are nearly the same, and the Gaussian driven function is superior to that of the sine driven function, when the maximum squeezing and the minimum variance of quantum fluctuation are considered. In the meantime, the generalization of frequency degenerate OPA to frequency non-degenerated OPA problem is investigated.     

Entanglement of movable mirror and cavity field enhanced by an optical parametric amplifier

A scheme to generate entanglement in a cavity optomechanical system filled with an optical parametric amplifier is proposed. With the help of the optical parametric amplifier, the stationary macroscopic entanglement between the movable mirror and the cavity field can be notably enhanced, and the entanglement increases when the parametric gain increases.Moreover, for a given parametric gain, the degree of entanglement of the cavity optomechanical system increases with increasing input laser power.     

压缩相干态通过参量图像放大系统的光学像

取压缩相干态作为参量图像放大系统的输入像，研究了输出光学像的性质.结果表明：参量 图像放大系统能够控制输出光学像的压缩度和压缩方向，即压缩度的增加与减小和压缩方向 的改变决定于参量图像放大系统的参数选择. 关键词： 参量图像放大系统 压缩相干态 压缩度 压缩方向角     

Character analysis of slow light with communication waveband in fiber optical parametric amplifier

The comprehensive characters of delay time and delay bandwidth with distortion, signal wavelength dependence and delay bandwidth product in fiber optical parametric amplifier are investigated theoretically when the pump locates at anomalous dispersion region. The delay character of single pulse, data stream with certain bit pattern and pseudo random data stream are analyzed comprehensively. In this category of fiber optical parametric amplifier, the delay time and delay bandwidth product vary from signal wavelengths and bit rates. For the same nonlinear coefficient, pump power and fiber length, the diverse dependences of bit pattern in different signal wavelengths are found by numerical simulation. The impacts of pump power and fiber length on the delay character and distortion are also discussed. These relations are conductive to the design of slow light based on fiber optical parametric amplifier in telecommunication waveband.     

参量放大器腔中光力诱导透明与本征模劈裂性质

研究了在含有光学参量放大器的光力学腔中关于弱探测光的光力诱导透明与本征模劈裂的性质.研究发现,光学参量放大器的驱动场相位和非线性增益值的大小对光力诱导透明窗口宽度和本征模劈裂性质有非常重要的影响,特别是当控制光频率工作在光力学红边带下,通过适当调制相位和非线性增益可以实现比空腔时(没有光学参量放大器时)还狭窄的光力诱导透明窗口,此时伴随着陡峭的色散曲线.这些研究结果有利于在光力耦合系统中实现快慢光、光存储等量子信息处理过程.     

信号光的调制对基于光纤光参量放大光脉冲源的改善

在理论上从四波混频的强度耦合方程出发,给出了基于光纤光参量放大(FOPA)光脉冲的光场表达式,并进一步分析了信号光被相位调制或强度调制后,光脉冲的频率啁啾和强度演化.结论指出：若信号光被强度调制,对所生成脉冲宽度无明显的影响,但可以提高消光比;若信号光被相位调制,所生成的脉冲具有更大的线性正啁啾,可以在相同的抽运功率条件下得到比无相位调制时更窄的脉冲.实验上给出了10 GHz工作速率下的结果,其结果与理论分析符合得很好.通过信号光的相位调制,在05 W平均抽运功率条件下得到了消光比22 dB,脉宽为5 关键词： 光纤参量放大 四波混频 光脉冲源 频率啁啾     

Gain characteristics and optimization of dual-pump fiber optical parametric amplifier using two-section highly nonlinear fibers

In this paper the gain characteristics of two-pump fiber optical parametric amplifiers (FOPA) with two-section highly nonlinear fibers are analyzed numerically and the parameters of the fibers are optimized to reach broad and flat gain spectra using genetic algorithm. Different from the previous methods, here the space between two pump wavelengths and the parameter β₄ of the fibers are included as a pivotal factor in the optimization. The numerical simulation shows that using two-section practical high nonlinear fibers, the amplifier may reach 110 nm bandwidth covering 1495–1605 nm with 10.5 dB average gain and gain ripple of 0.17 dB, when the total pump power is 1 W.     

Introduction to parametric amplification of quantum signals with Josephson circuits

This short and opinionated review starts with the concept of quantum signals at microwave frequencies and focuses on the principle of linear parametric amplification. This process emerges from the dispersive nonlinearity of Josephson junctions driven with appropriate tones. We discuss two defining characteristics of the corresponding amplifying devices: i) the number of modes excited by the signal, idler and pump waves and ii) the number of independent ports through which these waves enter into the circuit.     

泵浦场对吸收介质中的简并参量放大过程产生的压缩态的影响

本文利用前文结果,研究了泵浦场的强度,失谐等对压缩量的影响,并给出数值计算结果.     

Tunable phase-stabilized infrared parametric laser source

This paper reports that the tunable self-phase-stabilized infrared laser pulses have been generated from a two-stage optical parametric amplifier. With an 800 nm pump source, the output idler pulses are tunable from 1.3 μm to 2.3 μm, and the maximum output energy of the idler pulses is higher than 1 mJ at 1.6 μm by using 6 mJ pump laser. A carrier-envelope phase fluctuation of ～ 0.15 rad (rms) for the idler pulses is measured for longer than one hour by using a home build f-to-2f interferometer.     

A CW seeded femtosecond optical parametric amplifier

1 Introduction Optical parametric amplification (OPA) based on femtosecond Ti:sapphire regen-erative amplifiers has been widely adopted in wavelength extension of ultrashort opticalpulses[1]. While BBO-based femtosecond optical parametric amplifiers have alreadycommercialized, the tuning range of such an 800 nm-pumped OPA is typically between1.15 μm and 2.6 μm due to the limited transparent range of BBO. From application’spoint of view, ultrashort pulses near 1 μm and between 3 and 4 …     

1653 nm光参量放大器及在甲烷遥测方面的应用

基于掺氧化镁的周期性极化铌酸锂（MgO:PPLN）晶体,研究了连续波种子光注入结构的光参量放大器(OPA)。采用重复频率为10 kHz、最大平均输出功率为6 W的1064 nm高频脉冲激光作为抽运源,晶体的极化周期为31.02 m,在119 ℃工作温度下,将连续分布式反馈激光器（DFB）作为种子注入,在1652.3 nm处得到最大平均功率为125 mW的OPA信号光输出,量子转换效率为7.47％。实验通过改变注入种子光波长,实现了信号光nm级范围的调谐输出。信号光通过10 m外甲烷气池,观察到其光谱强度明显下降,初步验证了信号光在甲烷遥测领域的可行性。与用种子光直接检测相比,信号光强度更高,检测距离及灵敏度均有较大优势。     

Anomalous Josephson vortex solutions in Josephson junctions with multiple tunneling channels

We construct a theory for Josephson junction with multiple tunneling channels. We focus on two situations, i.e., a heterotic junction composed of two-gap-superconductor, insulator, and one-gap-superconductor, and a grain-boundary junction formed by two identical multi-gap superconductors. Then, we show that the magnetic field distribution of the Josephson vortex for ±s-wave superconductivity is much more enlarged than that for s-wave without sign change between the order parameters. We display such anomalous vortices and suggest how to evaluate the enlargement.     

Flux qubit with a large loop size and tunable Josephson junctions

We present the design of a superconducting flux qubit with a large loop inductance. The large loop inductance is desirable for coupling between qubits. The loop is configured into a gradiometer form that could reduce the interference from environmental magnetic noise. A combined Josephson junction, i.e., a DC-SQUID is used to replace the small Josephson junction in the usual 3-JJ (Josephaon junction) flux qubit, leading to a tunable energy gap by using an independent external flux line. We perform numerical calculations to investigate the dependence of the energy gap on qubit parameters such as junction capacitance, critical current, loop inductance, and the ratio of junction energy between small and large junctions in the flux qubit. We suggest a range of values for the parameters.     

Effects of the Noise on Voltage-Current Characteristics of Josephson Effect

In the case of T >> hω/k, by expanding the quasiparticle current power spectrum up to the third order term of hω/2kT, two noises are obtained: one is a white noise, the other is an O-U noise. We find that the two noises are the negative correlated noises, and correlation parameter λ is equal to -√6/3. Effects of the correlated noises on voltage-current characteristics curve are studied. The numerical computations show that the correlation parameter λ has very large effects on the voltage-current characteristics, but the correlation time τ of the O-U noise has a little effect.     

Amplification of 12 × 10 Gb/s WDM signals with negligible FWM crosstalk in a double-pumped fiber optical parametric amplifier

We report on the amplification of 12 × 10 Gb/s wavelength-division-multiplexed signals by a double-pumped fiber optic parametric amplifier (2P-FOPA). A gain of 10 dB is obtained using a 4.3 km-long conventional dispersion shifted fiber (DSF) as nonlinear medium. Our spectra show negligible generation of spurious FWM products, and we attribute this to the small variations of the zero-dispersion wavelength of the DSF. The 2P-FOPA performance is assessed through Q-factor measurements, and we show that for output powers per channel ranging from −15 to 3 dBm the power penalty is less than 0.5 dB.