比对法在计量标准考核验证中的应用探讨

为探讨比对法在计量标准考核验证中的可行性,将5家实验室分别对同一分度吸量管的检定结果进行比对,同时采用具有溯源性的传递比较法进一步验证比对法的可靠性。验证结果显示,采用比对法和传递比较法对被考核实验室的验证结果一致,说明采用比对法对检定结果的验证是有效的、可行的。     

Potentiometric and spectrophotometric determination of calcium in the wet end of paper machines by flow injection analysis

A spectrophotometric and a potentiometric FIA method were used to determine calcium in samples of back water from paper mills. The spectrophotometric method used the complexation reaction between calcium and o-cresolphthalein complexon. Optimum pH for the method was calculated theoretically. An ion-selective calcium electrode based on neutral carrier was used in the potentiometric method. The spectrophotometric method had a linear range between 10 and 250 ppm calcium and the potentiometric method between 10 and 300 ppm. Samples were acidified to pH 4 either before or after filtration. Total calcium was determined by a d.c. plasma emission method. Significant amounts of calcium were found to be bound both to the solid matter and to soluble complexes in the samples. The spectrophotometric method gave higher values than the potentiometric method but both of them gave lower values than the d.c. plasma emission method. Calcium concentrations in the range 30-250 ppm were found in the samples.     

On the Computation of Eigenvalues of the Anharmonic Coulombic Potential

In this work, we propose a method combining the Sinc collocation method with the double exponential transformation for computing the eigenvalues of the anharmonic Coulombic potential. We introduce a scaling factor that improves the convergence speed and the stability of the method. Further, we apply this method to Coulombic potentials leading to a highly efficient and accurate computation of the eigenvalues.     

Evaluation of hybrid laser-cut and cast miniature fracture specimens

This paper presents a new hybrid laser-cutting method for producing fracture test specimens from thermosetting materials. The hybrid approach combines casting of a sheet of material with subsequent laser-cutting of the test specimens. The new approach was compared to the traditional casting method using a fracture toughness test. For this study, a compact version of the tapered double cantilever beam (cTDCB) was used as a specimen geometry for both manufacturing methods. The cTDCB specimen is crack length independent, and crack length investigations were performed to ensure the crack length independence of the cTDCB specimens. The specimens that were made by the hybrid laser-cut method were found to be comparable to the specimens obtained by the traditional casting method. Moreover, the laser-cut method provides a fast and accurate method to make a significant number of samples in a reasonable time. These tests show that the hybrid laser-cut method could be a good alternative to the traditional casting method.     

The use of polyanions of hydrazines in the synthesis of heterocycles

A novel method for the synthesis of cyclic hydrazine derivatives is reported. The new method for the generation of nitrogen-containing heterocycles is based on a polyanion strategy. The described method provides a convenient access to cyclic hydrazine derivatives, which are extensively used in drug industry and agriculture. The advantages and limitations of the new method are also demonstrated.     

Application of a dynamic method of minimisation in the study of reaction surfaces

This paper describes the application of Snyman's dynamic minimisation method to a fitted potential surface of H₃. Comparisons are made with conventional algorithms. A method is described to extend Snyman's method so that it will find only a particular kind of stationary point. It is emphasized that this method enables saddle points to be found without having to resort to approaches based on trial and error.     

Liquid chromatographic determination of pyrantel tartrate in medicated formulations

The validation of a novel liquid chromatographic (LC) method for the determination of pyrantel tartrate in feed is presented. The method provides a significant improvement over the efficiency and precision of AOAC Official Method 978.30. The method was shown to be accurate, precise, linear, and robust for medicated articles. Unlike the official method, the LC method was shown to be a superior stability-indicating method. After the method was validated by using laboratory blends, the effectiveness of the method was demonstrated with marketed product as well.     

Comparison of sample-labeling techniques in DNA microarray experiments

Usage of DNA microarrays for gene expression analysis has become a common technique in many research laboratories and industry. Several target-labeling techniques have been devised to reduce the amount of RNA required for microarray experiments. In order to facilitate comparison and sharing of microarray data across the laboratories, it is crucial to determine the relative affects of these different sample-labeling techniques on the final results obtained from these experiments. We have compared two labeling methods designed for small RNA samples, an enzyme-based tyramide method (TSA) and a nucleic acid-based dendrimer method, to a more typical direct-labeling method that requires larger amounts of RNA. We observed comparable levels of reproducibility between replicate spots, with all the techniques. The dendrimer method resulted in a minimum number of spots (0.08%) that showed differential labeling due to a bias in the dyes used but resulted in highest background with only 71.4% of the spots measurable (above background) as compared to 93.3% for the TSA technique and 79.7% for the direct-labeling method. The results from differential labeling experiments showed that the dendrimer method performed better than the TSA method in detecting the same set of differentially expressed genes as observed with the direct method. Overall, our results show that the dendrimer method performs better than the TSA method. Differential labeling experiments using the TSA method show a non-linearity in the data at high intensities, leading to skewing of a portion of the data.     

Equivalence of Two Lower Bound Methods

Two lower bound methods are compared: the inverse method and a generalized variance method. As the generalized variance method is a generalization of the simple method of variance, the inverse method is shown to be a generalization of the Temple formula. We show that for the same a priori information and basis set, the generalized variance and inverse methods are equivalent.     

气相色谱叠加定量方法的研究

叠加法是由内标法衍生而来的一种气相色谱定量方法。对于较复杂混合物的分析,当选择内标物困难时,用叠加法定量更为方便。本文在大量实验的基础上,提出了叠加法定量过程中应注意的一些问题。     

Evaluation of the applicability of Jäntti’s method to volumetric sorption measurements

Jäntti published in 1970 a method to obtain values of the sorption parameters at an early stage of gravimetric sorption measurements. In the present paper we apply that method to volumetric sorption measurements to discuss its applicability. A method is presented to cope with inaccuracies when using Jäntti’s method. This will be of special importance for volumetric measurements where accuracy plays a major part. In the paper a second order regression method is used. We use a computer simulation as well as experimental data on desorption of nitrogen from a silica aerogel at 77 K.     

Development and validation of an improved liquid chromatographic method for the analysis of dirithromycin

The official method for the determination of dirithromycin and related substances in the European Pharmacopoeia (Ph. Eur.) and in the United States Pharmacopeia (USP) is an isocratic liquid chromatographic (LC) method using an ODS column. With this method, the separation of the main component dirithromycin from its epimer is not complete. Moreover, this method suffers sometimes from drift of the baseline and from subsequent quantitation problems. The required resolution is not easy to obtain.

Using an adapted method derived from the one prescribed in the pharmacopoeias, the selectivity of a set of more than 40 reversed-phase columns towards dirithromycin components was investigated. The selection of the most suitable column was achieved by the chromatographic response function (CRF) approach. Several changes were introduced to the method in order to improve the separation and to overcome the baseline drift problem. The resulting method uses a Zorbax Extend column maintained at 30 °C and a mobile phase containing acetonitrile, methanol, 2-propanol, water and a phosphate buffer at pH 7.5. The method allows a good separation of dirithromycin components, which is much better than that obtained with the existing methods. Several impurities of unknown identity are also separated. The method shows good repeatability, linearity and sensitivity, and it is robust. In addition, it proved to be applicable to a wide number of C18 reversed-phase columns.     

Cutoff radius effect of the isotropic periodic sum and Wolf method in liquid-vapor interfaces of water

As a more economical but similarly accurate computation method than the Ewald sum, the isotropic periodic sum (IPS) method for nonpolar molecules (IPSn) and polar molecules (IPSp), along with the Wolf method are of interest, but the cutoff radius dependence is an important issue. To evaluate the cutoff radius effect of the three methods, a water-vapor interfacial system has been studied by molecular dynamics. The Wolf method can produce adequate results for surface tension compared to that of the Ewald sum (within 2.9%) at a long enough cutoff radius, r(c). However, the estimation of the electrostatic potential profile and dipole orientational function is poor. The Wolf method cannot estimate electrostatic configuration at r(c) ≤ L(z)∕2 (L(z) is the longest lattice of the system). We have found that the convergence of the surface tension and the electrostatic configuration of the IPSn method is faster than that of the IPSp method. Moreover, the IPSn method is most accurate among the three methods for the same cutoff radius. Furthermore, the behavior of the surface tension against the cutoff radius shows a greater difference for the IPSn and IPSp method. The surface tension of the IPSp method fluctuates and presents a similar result to that of the Ewald sum, but the surface tension for the IPSn method greatly deviates near r(c) = L(z)∕3. The cause of this deviation is the difference between the interfacial configuration of the water surface and the cutoff treatment of the IPS method. The deviation becomes insignificant far from r(c) = L(z)∕3. In spite of this shortcoming, the IPSn method gives the most accurate result in estimating the surface tension at r(c) = L(z)∕2. From all the results in this work, the IPSn and IPSp method have been found to be more accurate than the Wolf method. In conclusion, the surface tension and structure of water-vapor interface can be calculated by the IPSn method when r(c) is greater than or equal to the longest lattice of the system. The IPSp method and the Wolf method require a longer cutoff radius than the longest lattice of the system to estimate interfacial properties.     

卟啉纳米材料的新法合成

采用液体分子嵌入法将卟啉分子引入到孔径为几十纳米的硅藻土孔内,制得了粒径在10～20nm左右的卟啉微晶.通过紫外、红外、X射线衍射、透射电镜和表面光电压谱等手段证实卟啉微晶被固载在硅藻土孔径内.     

Mathematical optimization in the determination of the dissociation constants of a tribasic organic acid by 13C NMR spectroscopy

The calculation of dissociation constants from the chemical shifts of (13)C NMR spectra leads to a complicated non-linear equation. Two different mathematical methods for solution of this equation have been chosen--an iterative step method and a matrix pseudo-inversion method. When the iteration method is used the initial guesses for the parameters, the initial value of the step size and the escalation of the iteration must be optimized. For comparison the matrix pseudo-inversion method was used because it gives a unique result. With the optimized step method the results were as accurate or even better than those obtained with the matrix method. Although it takes time to optimize the system, the step method is the more suitable method of solving the problem. The matrix inversion can be done only with a computer with 13 significant digits and exponent capacity larger than +/- 38.     

Metrological assessment of the high-accuracy RNAA method for determination of cobalt in biological materials

The paper summarizes work on the development of the high-accuracy RNAA method for the determination of trace amounts of cobalt in biological materials. The method is based on a combination of neutron activation with selective and quantitative isolation of the analyte in a state of high radiochemical purity by use of column chromatography followed by gamma-ray spectrometric measurements. The method was devised according to a set of rules, which were formulated to obtain high accuracy of the method. The procedure has been also equipped with several criteria as key factors in quality assurance. Qualification of the high-accuracy RNAA method as a primary ratio method has been demonstrated and its usefulness in the certification of the candidate reference materials tea leaves and mixed Polish herbs is presented.     

Modified liquid displacement method for determination of pore size distribution in porous membranes

A new method called constant pressure liquid displacement method (CPLM) was developed and tested to measure the pore size distribution of porous membranes. The permeability, defined as a ratio of the flow rate to the pressure applied, used to be assumed constant either for a conventional liquid displacement method or for a bubble point method, leading to the erroneous interpretation of the pore size distribution. However, it was possible to eliminate such an assumption by measuring the flow rates experimentally at a standard low pressure through the pores penetrated with a permeating liquid according to the proposed method. The pore size distribution for a hydrophobic PVDF membrane was successfully measured by the CPLM and compared with those measured by two different methods such as the conventional liquid displacement method and the mercury intrusion method.     

A novel photometric method for evaluation of the oxidative stability of virgin olive oils

The Oxitester method, a novel, simple, and fast photometric method for the evaluation of the antioxidant capacity of olive oils, was validated and compared to the official oil stability index (Rancimat) method. The Oxitester method appeared to be a good alternative to the Rancimat method with adequate correlation for a wide range of virgin olive oil samples, including extrissima virgin olive oils (correlation coefficient 0.88), and extra virgin olive oils of increased acidity (free fatty acids >0.45%, correlation coefficient 0.89). Other quality factors (flavor, free fatty acids content, specific absorbance at 270 and 232 nm, peroxide value, and content of oleic, linoleic, and linolenic acids) were also measured and correlated to the antioxidant capacity values of the Oxitester and Rancimat methods. The Oxitester method, in contrast to the Rancimat method, was indicative of the flavor characteristics of the olive oils and the content of linolenic acid.     

蔗糖酯的合成研究进展

综述了蔗糖酯的合成方法及工艺的研究进展,并对其反应机理进行了阐述.蔗糖酯的合成方法主要有四种:溶剂法、微乳化法、无溶剂法以及酶催化法.溶剂法采用DMF或DMSO为溶剂,但是这两种溶剂均有毒,限制了蔗糖酯在食品等行业的应用.微乳化法采用丙二醇或水代替溶剂法所使用的有毒溶剂,并加入乳化剂,使反应体系近似为均相体系.无溶剂法则是通过在反应体系中加入乳化剂或表面活性剂等使熔融相成均一相,反应平稳.但是一般无溶剂法反应温度较高,反应不易进行,产率低,且产品质量得不到保证.酶催化合成法是一种新的生物合成方法,采用生物酶代替传统的催化剂合成蔗糖酯,该法催化活性高、反应条件温和、选择性强、产物易分离等优点.文中还对蔗糖酯粗品的纯化工艺进行了介绍.