绕振荡水翼流动及其转捩特性的数值计算研究简

通过对比标准k-ω SST 湍流模型和基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型对绕振荡NACA66 水翼流动的数值计算结果与实验结果,对水翼振荡过程的水动力特性和流场结构变化进行了分析研究. 结果表明：与标准k-ω SST 湍流模型的数值计算结果相比,基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型能有效预测绕振荡翼型流场结构和水动力特性,捕捉流场边界层发生的流动分离和转捩现象;绕振荡水翼的流动过程可分为5 个特征阶段,当来流攻角较小时,在水翼前缘发生层流向湍流的转捩现象,水翼动力特征曲线出现变化拐点;随着来流攻角的增大,顺时针尾缘涡逐渐形成并向水翼前缘发展;当攻角较大时,前缘涡分离导致动力失速,水翼的动力特征曲线出现大幅波动;水翼处于顺时针向下旋转阶段,绕水翼的流动状态逐渐由湍流过渡为层流.     

绕振荡水翼流动及其转捩特性的数值计算研究

通过对比标准k-ω SST 湍流模型和基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型对绕振荡NACA66 水翼流动的数值计算结果与实验结果,对水翼振荡过程的水动力特性和流场结构变化进行了分析研究. 结果表明:与标准k-ω SST 湍流模型的数值计算结果相比,基于标准k-ω SST 湍流模型修正的γ-Re_θ 转捩湍流模型能有效预测绕振荡翼型流场结构和水动力特性,捕捉流场边界层发生的流动分离和转捩现象;绕振荡水翼的流动过程可分为5 个特征阶段,当来流攻角较小时,在水翼前缘发生层流向湍流的转捩现象,水翼动力特征曲线出现变化拐点;随着来流攻角的增大,顺时针尾缘涡逐渐形成并向水翼前缘发展;当攻角较大时,前缘涡分离导致动力失速,水翼的动力特征曲线出现大幅波动;水翼处于顺时针向下旋转阶段,绕水翼的流动状态逐渐由湍流过渡为层流.      

Stochastic estimation of flow near the trailing edge of a NACA0012 airfoil

A stochastic estimation technique has been applied to simultaneously acquired data of velocity and surface pressure as a tool to identify the sources of wall-pressure fluctuations. The measurements have been done on a NACA0012 airfoil at a Reynolds number of Re _c  = 2 × 10⁵, based on the chord of the airfoil, where a separated laminar boundary layer was present. By performing simultaneous measurements of the surface pressure fluctuations and of the velocity field in the boundary layer and wake of the airfoil, the wall-pressure sources near the trailing edge (TE) have been studied. The mechanisms and flow structures associated with the generation of the surface pressure have been investigated. The “quasi-instantaneous” velocity field resulting from the application of the technique has led to a picture of the evolution in time of the convecting surface pressure generating flow structures and revealed information about the sources of the wall-pressure fluctuations, their nature and variability. These sources are closely related to those of the radiated noise from the TE of an airfoil and to the vibration issues encountered in ship hulls for example. The NACA0012 airfoil had a 30 cm chord and aspect ratio of 1.     

Zonal RANS/LES coupling simulation of a transitional and separated flow around an airfoil near stall

The objective of the current study is to examine the course of events leading to stall just before its occurrence. The stall mechanisms are very sensitive to the transition that the boundary layer undergoes near the leading edge of the profile by a so-called laminar separation bubble (LSB). In order to provide helpful insights into this complex flow, a zonal Reynolds-averaged Navier–Stokes (RANS)/large-eddy simulation (LES) simulation of the flow around an airfoil near stall has been achieved and its results are presented and analyzed in this paper. LSB has already been numerically studied by direct numerical simulation (DNS) or LES, but for a flat plate with an adverse pressure gradient only. We intend, in this paper, to achieve a detailed analysis of the transition process by a LSB in more realistic conditions. The comparison with a linear instability analysis has shown that the numerical instability mechanism in the LSB provides the expected frequency of the perturbations. Furthermore, the right order of magnitude for the turbulence intensities at the reattachment point is found.      

Assessment of 2D/3D numerical modeling for deep dynamic stall experiments

The results of computational fluid dynamics (CFD) simulations in two and three spatial dimensions are compared to pressure measurements and particle image velocimetry (PIV) flow surveys to assess the suitability of numerical models for the simulation of deep dynamic stall experiments carried out on a pitching NACA 23012 airfoil. A sinusoidal pitching motion with a 10° amplitude and a reduced frequency of 0.1 is imposed around two different mean angles of attack of 10° and 15°. The comparison of the airloads curves and of the pressure distribution over the airfoil surface shows that a three-dimensional numerical model can better reproduce the flow structures and the airfoil performance for the deep dynamic stall regime. Also, the vortical structures observed by PIV in the flow field are better captured by the three-dimensional model. This feature highlighted the relevance of three-dimensional effects on the flow field in deep dynamic stall.     

High-fidelity simulations of moving and flexible airfoils at low Reynolds numbers

The present paper highlights results derived from the application of a high-fidelity simulation technique to the analysis of low-Reynolds-number transitional flows over moving and flexible canonical configurations motivated by small natural and man-made flyers. This effort addresses three separate fluid dynamic phenomena relevant to small fliers, including: laminar separation and transition over a stationary airfoil, transition effects on the dynamic stall vortex generated by a plunging airfoil, and the effect of flexibility on the flow structure above a membrane airfoil. The specific cases were also selected to permit comparison with available experimental measurements. First, the process of transition on a stationary SD7003 airfoil section over a range of Reynolds numbers and angles of attack is considered. Prior to stall, the flow exhibits a separated shear layer which rolls up into spanwise vortices. These vortices subsequently undergo spanwise instabilities, and ultimately breakdown into fine-scale turbulent structures as the boundary layer reattaches to the airfoil surface. In a time-averaged sense, the flow displays a closed laminar separation bubble which moves upstream and contracts in size with increasing angle of attack for a fixed Reynolds number. For a fixed angle of attack, as the Reynolds number decreases, the laminar separation bubble grows in vertical extent producing a significant increase in drag. For the lowest Reynolds number considered (Re _c  = 10⁴), transition does not occur over the airfoil at moderate angles of attack prior to stall. Next, the impact of a prescribed high-frequency small-amplitude plunging motion on the transitional flow over the SD7003 airfoil is investigated. The motion-induced high angle of attack results in unsteady separation in the leading edge and in the formation of dynamic-stall-like vortices which convect downstream close to the airfoil. At the lowest value of Reynolds number (Re _c  = 10⁴), transition effects are observed to be minor and the dynamic stall vortex system remains fairly coherent. For Re _c  = 4 × 10⁴, the dynamic-stall vortex system is laminar at is inception, however shortly afterwards, it experiences an abrupt breakdown associated with the onset of spanwise instability effects. The computed phased-averaged structures for both values of Reynolds number are found to be in good agreement with the experimental data. Finally, the effect of structural compliance on the unsteady flow past a membrane airfoil is investigated. The membrane deformation results in mean camber and large fluctuations which improve aerodynamic performance. Larger values of lift and a delay in stall are achieved relative to a rigid airfoil configuration. For Re _c = 4.85 × 10⁴, it is shown that correct prediction of the transitional process is critical to capturing the proper membrane structural response.     

Effects of sub-millimeter-bubble injection on transition to turbulence in natural convection boundary layer along a vertical plate in water

Temperature and velocity measurements are performed to clarify the effects of sub-millimeter-bubble injection on the transition to turbulence in the natural convection boundary layer along a vertical plate in water. In particular, we focus on the relationship between the bubble injection position L and the transition to turbulence in the natural convection boundary layer. The bubble injection positions used in our experiments are L = 1.6 and 3.6 mm. Bubble injection at L = 1.6 mm delays the transition to turbulence in the natural convection boundary layer, while that at L = 3.6 mm accelerates the transition to turbulence in the boundary layer. In the case of L = 1.6 mm, the appearance region of the liquid velocity fluctuation in the bubble-induced upward flow in the upstream unheated section is restricted to near the wall, although the peak of the liquid velocity fluctuation is high. In contrast, in the case of L = 3.6 mm, the relatively large liquid velocity fluctuation is distributed widely over the laminar boundary layer width. These results suggest that the effect of the liquid velocity fluctuation on the laminar boundary layer is quite different between L = 1.6 and 3.6 mm. It is therefore expected that the transition to turbulence in the natural convection boundary layer for the case with bubble injection is dependent on the magnitude and appearance region of the liquid velocity fluctuation in the bubble-induced upward flow in the upstream unheated section.     

Unsteady separated and reattaching turbulent flow over a two-dimensional square rib

The spatio-temporal characteristics of the separated and reattaching turbulent flow over a two-dimensional square rib were studied experimentally. Synchronized measurements of wall-pressure fluctuations and velocity fluctuations were made using a microphone array and a split-fiber film, respectively. Profiles of time-averaged streamwise velocity and wall-pressure fluctuations showed that the shear layer separated from the leading edge of the rib sweeps past the rib and directly reattaches on the bottom wall (x/H=9.75) downstream of the rib. A thin region of reverse flow was formed above the rib. The shedding large-scale vortical structures (fH/U₀=0.03) and the flapping separation bubble (fH/U₀=0.0075) could be discerned in the wall-pressure spectra. A multi-resolution analysis based on the maximum overlap discrete wavelet transform (MODWT) was performed to extract the intermittent events associated with the shedding large-scale vortical structures and the flapping separation bubble. The convective dynamics of the large-scale vortical structures were analyzed in terms of the autocorrelation of the continuous wavelet-transformed wall pressure, cross-correlation of the wall-pressure fluctuations, and the cross-correlation between the wall pressure at the time-averaged reattachment point and the streamwise velocity field. The convection speeds of the large-scale vortical structures before and after the reattachment point were U_c=0.35U₀ and 0.45U₀, respectively. The flapping motion of the separation bubble was analyzed in terms of the conditionally averaged reverse-flow intermittency near the wall region. The instantaneous reattachment point in response to the flapping motion was obtained; these findings established that the reattachment zone was a 1.2H-long region centered at x/H=9.75. The reverse-flow intermittency in one period of the flapping motion demonstrated that the thin reverse flow above the rib is influenced by the flapping motion of the separation bubble behind the rib.     

Turbulence modelling of the flow past a pitching NACA0012 airfoil at and Reynolds numbers

This paper provides a study of the NACA0012 dynamic stall at Reynolds numbers 10⁵ and 10⁶ by means of two- and three-dimensional numerical simulations. The turbulence effect on the dynamic stall is studied by statistical modelling. The results are compared with experiments concerning each test case. Standard URANS turbulence modelling have shown a quite dissipative character that attenuates the instabilities and the vortex structures related to the dynamic stall. The URANS approach Organised Eddy Simulation (OES) has shown an improved behaviour at the high Reynolds number range. Emphasis is given to the physical analysis of the three-dimensional dynamic stall structure, for which there exist few numerical results in the literature, as far as the Reynolds number range is concerned. This study has shown that the downstroke phases of the pitching motion are subjected to strong three-dimensional turbulence effects along the span, whereas the flow is practically two-dimensional during the upstroke motion.     

Flow analysis for wormlike micellar solutions in an axisymmetric capillary channel

Flows of wormlike micellar solutions in an axisymmetric capillary channel were studied both numerically and experimentally. In the experiments, an aqueous solution of cetyltrimethylammonium bromide (CTAB) with sodium salicylate (NaSal) was used as a test fluid. The mole concentration of CTAB is 0.03 mol/l, and that of NaSal is 0.06 mol/l. The velocity distribution was measured with a particle tracking velocimetry and flow visualization experiments were performed. The velocity profile showed a plug-like shape and had inflection points where the velocity gradient rapidly changed. High-shear-rate regions near the channel wall spread with increasing the average velocity. Moreover, the flow turned out to be unstable at high average velocities, and when the flow was unstable, white turbidity was observed near the capillary wall. Shear rates showing a white turbidity were included in the range of shear rate where a shear-rate jump in a flow curve occurred. These results suggest that both the characteristic velocity profile and the emergence of white turbidity relate the shear-rate-jump property of wormlike micellar solution. In the numerical analysis, startup flows were considered. A modified Bautista–Manero model was employed as a constitutive equation, and startup flows at a constant average velocity were numerically simulated. The velocity profile at steady state predicted by the numerical simulation adequately agreed with corresponding experimental data. The velocity profile changes from Newton-like to plug-like with time. Inflection points in velocity profile appeared and moved towards the center-side with time. Temporal changes in both velocity gradient and fluidity indicated that the behavior in velocity depended on the shear-rate-jump property of wormlike micellar solution. The velocity gradient rapidly changed around the inflection point and the range of velocity gradient corresponds to that where a white turbidity was observed in the experiments. An erratum to this article can be found at     

Investigation of steady plasma actuation effect on aerodynamic coefficients of oscillating airfoil at low Reynolds number

In this work, numerical study of two dimensional laminar incompressible flow around an oscillating NACA0012 airfoil is proceeded using the open source code Open FOAM. Oscillatory motion types including pitching and flapping are considered. Reynolds number for these motions is assumed to be 12000 and effects of these motions and also different unsteady parameters such as amplitude and reduced frequency on aerodynamic coefficients are studied. For flow control on airfoil, dielectric barrier discharge plasma actuator is used in two different positions on airfoil and its effect is compared for the two types of considered oscillating motions. It is observed that in pitching motion, imposing plasma leads to an improvement in aerodynamic coefficients, but it does not have any positive effect on flapping motion.Also, for the amplitudes and frequencies investigated in this paper, the trailing edge plasma had a more desirable effect than other positions.     

An experimental study of the effects of pitch-pivot-point location on the propulsion performance of a pitching airfoil

An experimental investigation was conducted to characterize the evolution of the unsteady vortex structures in the wake of a pitching airfoil with the pitch-pivot-point moving from 0.16C to 0.52C (C is the chord length of the airfoil). The experimental study was conducted in a low-speed wind tunnel with a symmetric NACA0012 airfoil model in pitching motion under different pitching kinematics (i.e., reduced frequency k=3.8–13.2). A high-resolution particle image velocimetry (PIV) system was used to conduct detailed flow field measurements to quantify the characteristics of the wake flow and the resultant propulsion performance of the pitching airfoil. Besides conducting “free-run” PIV measurements to determine the ensemble-averaged velocity distributions in the wake flow, “phase-locked” PIV measurements were also performed to elucidate further details about the behavior of the unsteady vortex structures. Both the vorticity–moment theorem and the integral momentum theorem were used to evaluate the effects of the pitch-pivot-point location on the propulsion performance of the pitching airfoil. It was found that the pitch-pivot-point would affect the evolution of the unsteady wake vortices and resultant propulsion performance of the pitching airfoil greatly. Moving the pitch-pivot-point of the pitching airfoil can be considered as adding a plunging motion to the original pitching motion. With the pitch-pivot-point moving forward (or backward), the added plunging motion would make the airfoil trailing edge moving in the same (or opposite) direction as of the original pitching motion, which resulted in the generated wake vortices and resultant thrust enhanced (or weakened) by the added plunging motion.     

激波/湍流边界层干扰压力脉动特性数值研究

激波/湍流边界层干扰问题广泛存在于高速飞行器内外流动中, 激波干扰会导致局部流场出现强压力脉动, 严重影响飞行器气动性能和飞行安全. 为了考察干扰区内脉动压力的统计特性, 对来流马赫数2.25, 激波角33.2°的入射激波与平板湍流边界层相互作用问题进行了直接数值模拟研究. 在对计算结果进行细致验证的基础上, 分析比较了干扰区外层和物面脉动压力的典型统计特征, 如脉动强度、功率谱密度、两点相关和时空关联特性等, 着重探讨了两者的差异及其原因. 研究发现, 激波干扰对外层和物面压力脉动的影响差异显著. 分离区内脉动以低频特征为主, 随后再附区外层压力脉动的峰值频率往高频区偏移, 而物面压力脉动的低频能量仍相对较高. 两点相关结果表明, 外层和物面脉动压力的展向关联性均明显强于其流向, 前者积分尺度过激波急剧增长随后缓慢衰减, 而后者积分尺度整体上呈现逐步增大趋势. 此外, 时空关联分析结果指出, 脉动压力关联系数等值线仍符合经典的椭圆形分布, 干扰区下游压力脉动对流速度将减小, 外层对流速度仍明显高于物面.      

Flow transition in dual bell nozzles

The dual bell nozzle is a concept of altitude adaptive nozzles. The flow adapts to the altitude by separation at the wall inflection at low altitude, and full flowing at high altitude. To understand the phenomenology of the flow by the transition from sea-level mode to high altitude mode, a series of tests have been made at the cold flow test bench P6.2 at DLR Lampoldshausen. A dual bell nozzle have been successively shorten and driven in the same conditions for each length. Hence it was possible to observe the flow in the vicinity of the wall inflection using Schlieren optics. Furthermore this study yields the influence of the length ratio between basis and extension on the transition conditions.

---

     

Investigation of the unsteady flow velocity field above an airfoil pitching under deep dynamic stall conditions

The unsteady flow field above a NACA 0012 airfoil pitching under deep dynamic stall conditions has been investigated in a low-speed wind tunnel by means of particle image velocimetry. The measurements of the instantaneous flow velocity field show the characteristic features of the dynamic stall process: formation and development of an organized vortex structure for increasing incidences and the subsequent separation. Vorticity and divergence estimated from the measured data give a good insight into the complex flow behaviour during the downstroke motion. Furthermore, small-scale structures could be observed in the separated flow field and even within the dynamic stall vortex.The authors would like to thank Dr. Schäfer (ISL) for his support in organizing the cooperative measurements, Mr. Seyb (DLR) for his help during the recording of PIV images, Dr. Bretthauer (DLR) and Mr. Vollmers (DLR) for his assistance during the phase of evaluation and post processing of the PIV recordings and Dr. Geißler (DLR) for helpful discussions on the dynamic stall problem.     

Measurement of unsteady boundary layer developed on an oscillating airfoil using multiple hot-film sensors

 The spatial-temporal progressions of the leading-edge stagnation, separation and reattachment points, and the state of the unsteady boundary layer developed on the upper surface of a 6 in. chord NACA 0012 airfoil model, oscillated sinusoidally within and beyond the static-stall angle, were measured using 140 closely-spaced, multiple hot-film sensors (MHFS). The MHFS measurements show that (i) the laminar separation point and transition were delayed with increasing α and the reattachment and relaminarization were promoted with decreasing α, relative to the static case, (ii) the pitchup motion helped to keep the boundary layer attached to higher angles of attack over that could be obtained statically, (iii) the dynamic stall process was initiated by the turbulent flow separation in the leading-edge region as well as by the onset of flow reversal in the trailing-edge region, and (iv) the dynamic stall process was found not to originate with the bursting of a laminar separation bubble, but with a breakdown of the turbulent boundary layer. The MHFS measurements also show that the flow unsteadiness caused by airfoil motion as well as by the flow disturbances can be detected simultaneously and nonintrusively. The MHFS characterizations of the unsteady boundary layers are useful in the study of unsteady separated flowfields generated by rapidly maneuvering aircraft, helicopter rotor blades, and wing energy machines. Received: 17 June 1997 / Accepted: 10 December 1997     

Microscopic particle image velocimetry measurements of transition to turbulence in microscale capillaries

The character of transitional capillary flow is investigated using pressure-drop measurements and instantaneous velocity fields acquired by microscopic PIV in the streamwise–wall-normal plane of a 536 μm capillary over the Reynolds-number range 1,800 ≤ Re ≤ 3,400 in increments of 100. The pressure-drop measurements reveal a deviation from laminar behavior at Re = 1,900 with the differences between the measured and the predicted laminar-flow pressure drop increasing with increasing Re. These observations are consistent with the characteristics of the mean velocity profiles which begin to deviate from the parabolic laminar profile at Re = 1,900, interpreted as the onset of transition, by becoming increasingly flatter and fuller with increasing Re. A fully-turbulent state is attained at Re ≅ 3,400 where the mean velocity profile collapses onto the mean profile of fully-developed turbulent pipe flow from an existing direct numerical simulation at Re = 5,300. Examination of the instantaneous velocity fields acquired by micro-PIV in the range 1,900 ≤ Re < 3,400 reveal that transitional flows at the microscale are composed of a subset of velocity fields illustrating a purely laminar behavior and a subset of fields that capture significant departure from laminar behavior. The fraction of velocity fields displaying non-laminar behavior increases with increasing Re, consistent with past observations of a growing number of intermittent turbulent spots bounded by nominally laminar flow in macroscale pipe flow with increasing Re. Instantaneous velocity fields that are non-laminar in character consistently contain multiple spanwise vortices that appear to streamwise-align to form larger-scale interfaces that incline slightly away from the wall. The characteristics of these “trains” of vortices are reminiscent of the spatial features of hairpin-like vortices and hairpin vortex packets often observed in fully-turbulent wall-bounded flow at both the macro- and micro-scales. Finally, single-point statistics computed from the non-laminar subsets at each transitional Re, including root-mean-square velocities and the Reynolds shear stress, reveal a gradual and smooth maturation of the patches of disordered motion toward a fully-turbulent state with increasing Re.     

Direct numerical simulation of a NACA0012 in full stall

This work aims at investigating the mechanisms of separation and the transition to turbulence in the separated shear-layer of aerodynamic profiles, while at the same time to gain insight into coherent structures formed in the separated zone at low-to-moderate Reynolds numbers. To do this, direct numerical simulations of the flow past a NACA0012 airfoil at Reynolds numbers Re = 50,000 (based on the free-stream velocity and the airfoil chord) and angles of attack AOA = 9.25° and AOA = 12° have been carried out. At low-to-moderate Reynolds numbers, NACA0012 exhibits a combination of leading-edge/trailing-edge stall which causes the massive separation of the flow on the suction side of the airfoil. The initially laminar shear layer undergoes transition to turbulence and vortices formed are shed forming a von Kármán like vortex street in the airfoil wake. The main characteristics of this flow together with its main features, including power spectra of a set of selected monitoring probes at different positions on the suction side and in the wake of the airfoil are provided and discussed in detail.     

Numerical investigations of the vortex interactions for a flow over a pitching foil at different stages

The fluid–structure interaction is investigated numerically for a two-dimensional flow (Re=2.5·10⁶) over a sinusoid-pitching foil by the SST (Shear Stress Transport) k–ω model. Although discrepancies in the downstroke phase, which are also documented in other numerical studies, are observed by comparing with experimental results, our current numerical results are sufficient to predict the mean features and qualitative tendencies of the dynamic stall phenomenon. These discrepancies are evaluated carefully from the numerical and experimental viewpoints.In this study, we have utilized Λ, which is the normalized second invariant of the velocity gradient tensor, to present the evolution of the Leading Edge Vortex (LEV) and Trailing Edge Vortex (TEV). The convective, pressure, and diffusion terms during the dynamic stall process are discussed based on the transport equation of Λ. It is found that the pressure term dominates the rate of the change of the rotation strength inside the LEV. This trend can hardly be observed directly by using the vorticity transport equation due to the zero baroclinic term for the incompressible flow.The mechanisms to delay the stall are categorized based on the formation of the LEV. At the first stage before the formation of the LEV in the upper surface, the pitching foil provides extra momentum into the fluid flows to resist the flow separation, and hence the stall is delayed. At the second stage, a low-pressure area travels with the evolution of the LEV such that the lift still can be maintained. Three short periods at the second stage corresponds to different flow patterns during the dynamic stall, and these short periods can be distinguished according to the trend of the pressure variation inside the LEV. The lift stall occurs when a reverse flow from the lower surface is triggered during the shedding of the LEV. For a reduced frequency k_f=0.15, the formation of the TEV happens right after the lift stall, and the lift can drop dramatically. With a faster reduced frequency k_f=0.25, the shedding of the LEV is postponed into the downstroke, and the interaction between the LEV and TEV becomes weaker correspondingly. Thus, the lift drops more gently after the stall. In order to acquire more reliable numerical results within the downstroke phase, the Large Eddy Simulation (LES), which is capable of better predictions for the laminar-to-turbulent transition and flow reattachment process, will be considered as the future work.     

水下爆炸冲击波壁压理论及数值计算方法改进研究

水下爆炸冲击波是舰船抗冲击评估中重要的载荷成分,也是水中结构物毁伤程度快速预报的关键和依据。通过小当量实验发现,由于传统 Taylor 平板理论公式忽略了冲击波波速的非线性变化 ,导致其在预报近距离水下爆炸冲击波壁压脉宽时出现偏差。为此,给出了比例爆距R/W1/3为0.11～5.30 m/kg1/3 (R为爆距,W为炸药质量)下的冲击波速度拟合公式,对传统Taylor理论公式进行修正。修正后,在R/W1/3=0.11 m/kg1/3下,壁压脉宽及冲量偏差大幅减小;在R/W1/3≥0.21 m/kg1/3下,两者偏差均小于12%。此外,在处理水下近场和中远场爆炸问题时,发现数值耗散会导致壁压峰值被明显削弱,于是提出了一种可行的数值策略消除计算中数值耗散导致的削弱效应,结果与修正的Taylor平板理论公式吻合良好,峰值偏差均小于9%。改进后的冲击波壁压理论公式及数值计算方法可为舰船抗爆抗冲击领域提供理论和技术支撑。