Spectral and thermal characterization of polyaniline–oxalic acid salt

Polyaniline–oxalic acid salts were prepared at 5 and 30°C by chemical polymerization of aniline using different concentration of oxalic acid. Polyaniline base was obtained from the corresponding polyaniline salt by dedoping using aqueous ammonium hydroxide solution. Conductivity measurements, elemental analysis, Infrared, electronic absorption, electron paramagnetic resonance spectral, and thermogravimetric analysis were performed on the polyaniline salts and bases. Composition and the extent of dopant in polyaniline salt systems where determined. The value of composition of polyaniline: oxalic acid is 4: 1.6 and the polymer yield is around 66%. The value of conductivity, polymer yield and composition of polyaniline–oxalic acid salt is independent of concentration of oxalic acid used and also the synthesis temperature. The results are compared with polyaniline–hydrochloride salt prepared by chemical polymerization. The conductivity of polyaniline–oxalic acid salt is three orders of magnitude lower than that of polyaniline-hydrocholoride salt. © 1995 John Wiley & Sons, Inc.     

树状大分子聚酰胺-胺的合成及对药物分子增溶性能研究

采用发散法合成了以乙二胺为核的1．0～3．0树状大分子聚酰胺-胺(PAMAM)．采用红外光谱和核磁共振对PAMAM的结构进行了表征，并考察了不同pH值、不同浓度的PAMAM对难溶药物布洛芬的增溶能力．结果表明：PAMAM较十二烷基苯磺酸钠(SDS)对布洛芬有较强的增溶能力，增溶量随PAMAM浓度增加而增大，其增溶机理是由于PAMAM的氨基与布洛芬的羧基之间存在静电作用．     

Surface characterization and electrical behavior of polyaniline–polymannuronate nanocomposites

Conducting polyaniline‐polymannuronate (PANI‐PM) composites were synthesized via in situ deposition techniques. By dissolving different weight percentages of polymannuronate (PM) (5, 10, 15, and 25%), the oxidative polymerization of aniline was achieved through the use of ammonium persulfate as oxidant. Structural morphology, FT‐IR, and X‐ray diffraction (XRD) studies support a strong interaction between PANI and PM. The temperature‐dependent DC conductivity of PANI‐PM composites was studied within the range of 300 ≤ T ≤ 500 °K, presenting evidence for the transport properties of PANI‐PM composites. Conductivity was analyzed through Mott's equation, which leveraged the variable range hopping model in three dimensions. Parameters such as density of states at the Fermi energy, hopping energy, and hopping distance were calculated. Based on the above factors, the synthesis of PANI‐PM composites envisages the future development of biomimetic materials for the creation of a new bionanocomposite as a multicomponent and multifunctional material. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 36–45, 2009     

Synthesis and characterization of electrically conducting polyaniline–TCNE complexes

Polyaniline–tetracyanoethylene (TCNE) complexes can be synthesized either from emeraldine base or emeraldine hydrochloride by a relatively simple method. The complexes demonstrate greater stability than the emeraldine hydrochloride at elevated temperatures and under high current densities. The electrical conductivity of the complexes synthesized from emeraldine base can be varied from < 10^?6 to 0.2 S/cm by varying the amount of TCNE incorporated. The complexes synthesized from emeraldine hydrochloride are slightly more conductive than the starting emeraldine hydrochloride. In both types of complexes, it appears that electron transfer between the polyaniline and TCNE has occurred resulting in the formation of some positively charged polyaniline nitrogen and TCNE anions.     

Synthesis and photophysical characterization of amphiphilic dendritic–linear–dendritic block copolymers

Amphiphilic dendritic–linear–dendritic triblock copolymers based on hydrophilic linear poly(ethylene oxide) (PEO) and hydrophobic dendritic carbosilane were synthesized with a divergent approach at the allyl end groups of diallyl‐terminated PEO. Their micellar characteristics in an aqueous phase were investigated with dynamic light scattering, fluorescence techniques, and transmission electron microscopy. The block copolymer with the dendritic moiety of a third generation could not be dispersed in water. The block copolymers with the first (PEO–D ‐Si‐1G) and second (PEO–D ‐Si‐2G) generations of dendritic carbosilane blocks formed micelles in an aqueous phase. The critical micelle concentrations of PEO–D ‐Si‐1G and PEO–D ‐Si‐2G, determined by a fluorescence technique, were 27 and 16 mg/L, respectively. The mean diameters of the micelles of PEO–D ‐Si‐1G and PEO–D ‐Si‐2G, measured by dynamic light scattering, were 170 and 190 nm, respectively, which suggests that the micelles had a multicore‐type structure. The partition equilibrium constants of pyrene in the micellar solution increased with the increasing size of the dendritic block (e.g., 7.68 × 10⁴ for PEO–D ‐Si‐1G and 9.57 × 10⁴ for PEO–D ‐Si‐2G). The steady‐state fluorescence anisotropy values (r) of 1,6‐diphenyl‐1,3,5‐hexatriene were 0.06 for PEO–D ‐Si‐1G and 0.09 for PEO–D ‐Si‐2G. The r values were lower than those of the linear polymeric amphiphiles, suggesting that the microviscosity of the dendritic micellar core was lower than that of the linear polymeric analogues. © 2001 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 39: 918–926, 2001     

Synthesis and characterization of polyaniline‐multiwalled carbon nanotube nanocomposites in the presence of sodium dodecyl sulfate

Polyaniline‐carboxylic acid functionalized multi‐walled carbon nanotube (PAni/c‐MWNT) nanocomposites were prepared in sodium dodecyl sulfate (SDS) emulsion. First, the c‐MWNTs were dispersed in SDS emulsion then the aniline was polymerized by the addition of ammonium persulfate in the absence of any added acid. SDS forms the functionalized counterion in the resulting nanocomposites. The content of c‐MWNTs in the nanocomposites varied from 0 to 20 wt%. A uniform coating of PAni was observed on the c‐MWNTs by field‐emission scanning electron microscopy (FESEM). The PAni/c‐MWNT nanocomposites have been characterized by different spectroscopic methods such as UV‐Visible, FT‐Raman, and FT‐IR. The UV‐Visible spectra of the PAni/c‐MWNT nanocomposites exhibited an additional band at around 460 nm, which implies the induced doping of the MWNTs by the carboxyl group. The FT‐IR spectra of the PAni/c‐MWNT nanocomposites showed an inverse intensity ratio of the bands at 1562 and 1480 cm^?1 as compared to that of pure PAni, which reveals that the PAni in the nanocomposites is richer in quinoid units than the pure PAni. The increase in the thermal stability of conductivity of the nanocomposites was due to the network structure of nanotubes and the charge transfer between the quinoid rings of the PAni and the c‐MWNTs. Copyright © 2008 John Wiley & Sons, Ltd.     

Temperature-sensitive polyamidoamine dendrimer/poly(N-isopropylacrylamide) hydrogels with improved responsive properties

Novel temperature-sensitive poly(N-isopropylacrylamide)/amine-terminated polyamidoamine dendrimer G6-NH2 hydrogels with fast responsive properties were synthesized by forming semi-interpenetrating polymeric networks. In contrast to the conventional PNIPA hydrogel, these new gels showed rapid shrinking rate at the temperature above lower critical solution temperature (LCST), and exhibited higher equilibrium swelling ratio at room temperature. All these properties might be attributed to the incorporation of polyamidoamine dendrimer G6-NH2, which forms water-releasing channels and increases the hydrophilicity of PNIPA network. The novel hydrogels have potential applications in drug and gene delivery.     

Electrical conductivity change of polyaniline–dodecyl benzene sulfonic acid complex with temperature

Polyaniline–dodecylbenzene sulfonic acid (PAn–DBSA) complex was thermally treated and its conductivity and structure change were investigated. The conductivity increased linearly from 1.1 × 10⁻⁴ to 3.0 × 10⁻¹ S/cm on thermal heating until 140°C, but decayed above 200°C. The increase was caused by an additional thermal doping resulting from an increasing mobility of undoped dopants. After the thermal doping, the formation of the layered structure of PAn–DBSA is made. The decrease was caused by the thermal decomposition of dopants. The conductivity changes at a high temperature was strongly dependent on the nature of the dopant. The results were confirmed by means of X-ray patterns and Fourier transform infrared spectra obtained in the heating and cooling processes of polyaniline.     

Synthesis of polyamidoamine dendrimer (PAMAM/CuS/AA) nanocomposite and its application in the removal of Isma acid fast yellow G Dye

The adsorption of Isma acid fast yellow G dye was studied using polyamidoamine (PAMAM)/Copper sulfide (CuS)/AA nanocomposite containing different amounts of CuS by batch technique. PAMAM dendrimer/CuS/AA nanocomposites were synthesized via gamma irradiation cross‐linking method with the aid of sonication. The nanocomposites were characterized by Fourier‐transform infrared, X‐ray diffraction, transmission electron microscope, energy dispersive spectroscopy X‐ray, thermal gravimetric analysis, ultraviolet‐visible, and fluorescence spectroscopy. The size of the CuS nanoparticles was formed in the range of 12–19 nm. The adsorption capacity of the nanocomposites was evaluated as a function of initial dye concentration, pH, adsorbent dosage, and time. It was verified that the adsorption rate fits a pseudo‐second‐order kinetics for initial Isma acid fast yellow G dye concentrations. Results indicated that the adsorption of Isma acid fast yellow G dye fitted well to the Langmuir model. Our results demonstrate that the PAMAM dendrimer/CuS/AA nanocomposite is very promising for removing organic dyes from wastewater. Copyright © 2015 John Wiley & Sons, Ltd.     

Synthesis of glycopeptide dendrimer by a convergent method

Glycopeptide thioester comprising the sequence of extracellular matrix metalloproteinase inducer (emmprin) (34-58) was prepared and condensed with a dendrimer core having eight amino groups by the thioester method. The desired product, a glycopeptide dendrimer carrying an N-linked core pentasaccharide of about 30 kDa, was successfully isolated by preparative electrophoresis and characterized by mass analysis.     

Synthesis of a novel water-soluble polyamide dendrimer based on a facile convergent method

A novel, rapid, inexpensive, and highly efficient convergent approach has been developed for the synthesis of a 32-amine-terminated G3 polyamide dendrimer by the hydrolysis of the dendrimer with trifluoroacetamide groups. The resulting dendrimer could be successfully modified with oligo(ethylene glycol) chains at its periphery to afford a novel water-soluble polyamide dendrimer. The structural homogeneity of the dendrimers was confirmed by NMR and MALDI-TOF mass spectroscopies.     

Viologen-terminated polyamidoamine (PAMAM) dendrimer encapsulated with gold nanoparticles for nonenzymatic determination of hydrogen peroxide

The development of an accurate and low-cost monitoring technique for hydrogen peroxide (H₂O₂) is a crucial demand in environment, food industry, medicine and biology. Herein, we report the design and synthesis of viologen terminated second (G2.0) and third generation (G3.0) poly(amidoamine) PAMAM dendrimers, followed by encapsulation with gold nanoparticles to form G2.0 and G3.0 Vio-PAMAM-AuNPs. The G2.0 and G3.0 Vio-PAMAM-AuNPs were deposited over glassy carbon electrode (GCE) to form G2.0 and G3.0 Vio-PAMAM-AuNPs/GCE modified electrodes, respectively. The electrochemical behavior of G2.0 and G3.0 Vio-PAMAM-AuNPs/GCEs were investigated using electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). Both the G2.0 and G3.0 Vio-PAMAM-AuNPs/GCEs showed a pair of well-defined redox peaks in 0.1 M phosphate buffer corresponding to the redox behavior of viologen V²⁺?V^?+ radical. G3.0 Vio-PAMAM-AuNPs/GCE has shown a higher current response than that of the G2.0 Vio-PAMAM-AuNPs/GCE and further the G3.0 Vio-PAMAM-AuNPs/GCE demonstrated impressive electrocatalytic activity towards reduction of H₂O₂, based on which a nonenzymatic sensor for the detection of H₂O₂ has been developed. The developed nonenzymatic sensor has displayed excellent performance towards H₂O₂ detection in the broad linear range of 0.1 mM – 6.2 mM with a low detection limit of 27 μM and high sensitivity of 202.7 μA mM^?1 cm^?2. The G3.0 Vio-PAMAM-AuNPs/GCE modified electrode with its extensive dendritic structure creating tailored sanctuary to accommodate a large number of viologen mediator and AuNPs exhibited good operational and long term stability and further the quantification of H₂O₂ in real samples has been verified by standard addition method.     

Viscoelastic properties and phase behavior of 12‐tert‐butyl ester dendrimer/poly(methyl methacrylate) blends

This study used refractometry, ultraviolet–visible spectroscopy, Fourier transform infrared spectroscopy, differential scanning calorimetry, and dielectric analysis to assess the viscoelastic properties and phase behavior of blends containing 0–20% (w/w) 12‐tert‐butyl ester dendrimer in poly(methyl methacrylate) (PMMA). Dendritic blends were miscible up through 12%, exhibiting an intermediate glass‐transition temperature (T_g; α) between those of the two pure components. Interactions of PMMA C?O groups and dendrimer N? H groups contributed to miscibility. T_g decreased with increasing dendrimer content before phase separation. The dendrimer exhibited phase separation at 15%, as revealed by Rayleigh scattering in ultraviolet–visible spectra and the emergence of a second T_g in dielectric studies. Before phase separation, clear, secondary β relaxations for PMMA were observed at low frequencies via dielectric analysis. Apparent activation energies were obtained through Arrhenius characterization. A merged αβ process for PMMA occurred at higher frequencies and temperatures in the blends. Dielectric data for the phase‐separated dendrimer relaxation (α_D) in the 20% blend conformed to Williams–Landel–Ferry behavior, which allowed the calculation of the apparent activation energy. The α_D relaxation data, analyzed both before and after treatment with the electric modulus, compared well with neat dendrimer data, which confirmed that this relaxation was due to an isolated dendrimer phase. © 2001 John Wiley & Sons, Inc. J Polym Sci Part B: Polym Phys 39: 1381–1393, 2001     

Synthesis and characterization of aluminum–polyaniline thin films and membranes

Polyaniline (PAni) films of different intrinsic oxidation states, including emeraldine salt, emeraldine base and leucoemeraldine base, were synthesized. Free‐standing membranes and thin film bilayers of aluminum–polyaniline were fabricated by magnetron sputter deposition of aluminum onto polyaniline films. Aluminum–polyaniline samples were analyzed by transmission electron microscopy (TEM) to investigate the microstructures of specimens, including cross‐sectional TEM micrographs of the metal‐polyaniline interfacial structure not previously reported in the literature. Auger electron spectroscopy (AES) and X‐ray photoelectron spectroscopy (XPS) were employed to study the chemical bonding and interaction between deposited aluminum and polyaniline at the interface. Results indicated that the intrinsic oxidation state of the polyaniline influenced the chemistry of the aluminum–polyaniline interface. Distinct interaction between aluminum and polyaniline in the emeraldine salt‐form was observed. However, there was no evidence of direct interactions of the aluminum with emeraldine base and leucoemeraldine base polyaniline. Copyright © 2005 John Wiley & Sons, Ltd.     

Adsorption performance and mechanism of Schiff base functionalized polyamidoamine dendrimer/silica for aqueous Mn(II) and Co(II)

Schiff base functionalized polyamidoamine (PAMAM) dendrimer/silica were prepared for the adsorption of aqueous Mn(II) and Co(II). The effects that influence the adsorption were investigated systematically and the adsorption mechanism was illustrated by theoretical calculation. The optimum adsorption pH are 4 and 6 for Mn(II) and Co(II). Adsorption kinetics follow pseudo-second-order model and the rate-controlling step is film diffusion process. Adsorption isotherm shows that high initial metal ion concentration facilitates the uptake of metal ions. The adsorption capacity increases first and then decreases in the temperature range of 15–35 °C. Density functional theory (DFT) calculation demonstrates that Schiff base functionalized PAMAM dendrimer tends to coordinate Mn(II) and Co(II) with the oxygen atoms of hydroxyl and carbonyl groups, nitrogen of tertiary amine and imino groups. The imino and tertiary amine groups mainly dominate the adsorption. The reproducibility of the adsorbents indicates they can be regenerated by 5% thiourea and 0.5 mol/L HNO₃ solution efficiently.     

Synthesis,characterization, AC conductivity,and diode properties of polyaniline–CaTiO3 composites

Polyaniline–CaTiO₃ composites of different weight percentages were prepared by in situ polymerization. The prepared composites were characterized by Fourier transform infrared spectroscopy for structural studies, and a morphology analysis was carried out by scanning electron microscopy studies. Real and imaginary parts of the complex impedance were determined for given samples as a function of frequency. Current–voltage and capacitance–voltage measurements were also carried out. The carrier mobility μ values of neat polyaniline and polyaniline–CaTiO₃ composites were found to be 5.37 × 10^?3 and 2.73 × 10^?2, respectively, and a significant enhancement, as compared with the reported data, was observed. Therefore, this study may provide a better route for technological applications in all fields in the near future and can also be represented by a pure electronic model. Copyright © 2013 John Wiley & Sons, Ltd.     

Synthesis and photoluminescence study of anthracene based dendrimer and dendron

A new type of polyaromatic dendrimer composed of six anthracene groups was synthesized, which showed a monomeric fluorescence feature with a diminished quantum yield due to intramolecular self-quenching processes in the dendritic framework.     

Diels–Alder reaction of anthracene on grafted polysiloxane and cylindrical carbosilane dendrimer

Anthracene‐grafted polysiloxane was prepared by the dehydrocoupling between linear siloxane polymers and anthracenecarbinol. The cylindrical type of dendritic polysiloxane was prepared up to the second generation by the hydrosilation between polysiloxane and vinyltrichlorosilane, and the continual addition of allyl alcohol. The anthracene groups on cylindrical dendrimers were prepared by the reaction of Si? Cl bonds on the polymer and anthracenecarbinol. The Diels–Alder reaction of anthracene moieties on polysiloxane and maleimide derivatives, maleic acid anhydride, and 1,4‐quinone derivatives was carried out under mild conditions. The polymers prepared were characterized by NMR and gel‐permeation chromatography. Copyright © 2005 John Wiley & Sons, Ltd.     

Conducting composites from EPDM–EVA blends

The effect of ethylidene norbornene (ENB) content of ethylene propylene aiene rubber (EPDM) and vinyl acetate (VA) content of ethylene vinyl acetate copolymer (EVA), as well as the blending sequence, on the conductivity of composites based on EPDM–EVA–carbon black have been studied. Black master batches show a lower extent of cure than the preblended system followed by black addition. EPDM having a high ENB content shows higher conductivity under ambient conditions. Preblended systems give rise to higher conductivity in the case of low-ENB content EPDM. But for high-ENB content EPDM, the blending of black master batches imparts high conductivity. Two types of conduction are observed in this case and the transition temperature depends on the VA content of EVA. It appears that there exists a correlation between activation energy of curing and that of conduction.     

SiO2–poly(amidoamine) dendrimer inorganic/organic hybrids

SiO₂–poly(amidoamine) (PAMAM) dendrimer hybrids were synthesized via (1) a Michael addition reaction between the dendrimer and 3‐(trimethoxysilyl) propyl acrylate, (2) the dissolution of the formed compound in methanol, and (3) the mixing of the latter solution with a methanol solution of partly hydrolyzed tetraethylorthosilicate (TEOS) and its casting on a glass substrate. ¹H NMR indicated that in the first step, 77% of the secondary amines were converted into tertiary amines when the fourth‐generation dendrimer was employed and 46% were converted when the second‐generation dendrimer was used. The final SiO₂–PAMAM dendrimer hybrids were obtained via the hydrolysis and condensation of the compound obtained via the Michael addition and the methanol solution of partly hydrolyzed TEOS. The compartmentalized structure of the hybrids due to the compartments of the dendrimers could be controlled by changing the dendrimer and the amount of TEOS. Scanning electron microscopy and transmission electron microscopy micrographs provided information about the structure of the hybrids. Like the PAMAM dendrimer, the SiO₂–PAMAM dendrimer hybrids exhibited a high metal ion complexing capacity because of the presence of the compartments of the dendrimer; they can be, however, much more easily handled, and, as demonstrated by thermogravimetric experiments, have much higher thermal resistance. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1443–1449, 2000