硫酸特布他林分子印迹电极的制备与性能研究

采用分子印迹技术,以邻苯二胺为功能单体,在玻碳电极表面电聚合成聚邻苯二胺分子印迹敏感膜。K3[Fe(CN)6]作为探针分子,通过循环伏安法、差分脉冲法对该电极进行考察。结果表明:电极对硫酸特布他林具有较好的灵敏度与选择性,线性范围为1.52×10-8~1.05×10-6mol/L,检出限(S/N=3)为1.2×10-8mol/L,电极具有良好的重现性与稳定性。将电极用于实际样品的分析,方法回收率为98.4%~107.9%。     

硫酸特布他林在聚铬黑T修饰电极上的电化学行为及其测定

采用电化学聚合法制备了聚铬黑T膜修饰电极,应用扫描电镜、交流阻抗法和循环伏安法对修饰电极进行表征,以循环伏安法研究硫酸特布他林在修饰电极上的电化学行为,并以差示脉冲伏安法对其含量进行测定.该方法对硫酸特布他林有明显的电催化作用,在pH 7.0磷酸盐缓冲液中,氧化峰电流与硫酸特布他林浓度在1.2x10^-7~2.0x10^-6mol•L^-1范围内呈良好的线性关系,检测限为1.5x10^-8 mol•L^-1,回收率在97.9%～104.6%之间,RSD在2.8 % (C=8x10^-7mol•L^-1,n=11).该方法简便灵敏,结果准确可靠,方法重复性好,可用于硫酸特布他林及其片剂的质量控制.     

Nafion修饰碳纤维微电极在抗坏血酸共存下选择性测定去甲肾上腺素

制备了碳纤维微电极,将洁净的碳纤维微电极浸入Nafion溶液中,采用电沉积的方法制得Nafion修饰碳纤维微电极。采用循环伏安法(CV)、差分脉冲伏安法(DPV)研究了去甲肾上腺素(NE)和抗坏血酸(AA)在电极上的电化学行为。结果表明:在最优条件下制备的Nafion修饰电极能完全屏蔽AA的电化学响应,而对NE仍表现出良好的电化学响应。修饰电极能在1.0 mmol/L AA的共存下选择性地测定NE,采用DPV进行检测,NE的氧化峰电流与其浓度在1.0×10~(-6)~1.0×10~(-4)mol/L范围内呈良好的线性关系,相关系数(r~2)为0.991 2,检出限(S/N=3)为8.6×10~(-7)mol/L。利用该方法测定了模拟样品中NE的含量,平均加标回收率为101.6%。该电极的重现性和稳定性良好,且具有良好的灵敏度和选择性,有望用于复杂生物环境中NE浓度的检测。     

纳米金修饰的碳纤维超微电极在高浓度抗坏血酸体系中选择性测定多巴胺

将柠檬酸三钠与硼氢化钠还原氯金酸制备纳米金颗粒,采用一步恒电位沉积的方法在碳纤维超微电极上沉积纳米金颗粒,并对电极进行电化学表征。分别对100μmol/L DA、1mmol/L AA在该电极上修饰前后的电化学行为进行了研究,结果表明在浓度为1 mmol/L抗坏血酸共存下,DA的浓度(0. 1～10μmol/L)与氧化峰电流成正比,线性回归方程为Ip(μA)=200 c(μmol/L)+2×10~(-4),相关系数R~2=0. 9979,线性范围0. 1～10μmol/L,检出限为1. 28×10~(-2)μmol/L (S/N=3)。方法可用于较高浓度抗坏血酸共存下对多巴胺的选择性测定。     

碳纤维组合超微园盘电极的伏安特性与理论验证

用12根直径7μm碳纤维均匀胶结在外径1mm、内径0．4mm的有机玻璃毛细管外围，形成组合超微园盘电极。并与Ag/AgCl参比电极和铂丝辅助电极构成复合三电极系统。在K3Pe(CN)6／K4Pe(CN)6和Cd^2 ／KCl溶液体系中，测定了这种复合式的组合超微电极的循环伏安特性和阶梯扫描伏安特性。理论计算与实验曲线一致。该电极系统具有良好的组合超微电极的性能。由于单电极间距离远大于本身直径，扩散场互不干扰，因此，组合超微电极的响应具有加和性。应用这种复合超微电极，测定了工业污水中的镉含量，与普通极谱法测定结果一致。     

CeO2纳米晶包裹碳纳米管修饰电极对特布他林的电催化测定

制备出CeO2纳米晶包裹碳纳米管修饰玻碳电极,并运用循环伏安法、交流阻抗谱探讨了该电极的电化学特性。研究了特布他林在该修饰电极上的直接电化学行为。实验结果表明,特布他林在该修饰电极上具有良好的电流响应,与裸玻碳电极相比在pH 7.0缓冲溶液中氧化峰电位负移314 mV。采用计时电流法测定特布他林,其氧化峰电流与浓度在5.0×10-7~1.0×10-4mol/L范围呈良好线性关系,线性方程为:Ip(μA)=4.952-0.04724c(μmol/L),线性相关系数为0.9920,检出限为5.0×10-8mol/L(信噪比为3)。该电极已用于特布他林片剂中特布他林的测定。     

在抗坏血酸存在下用L-赖氨酸修饰玻碳电极测定多巴胺

采用电化学氧化法制备了L-广赖氮酸单分子层修饰玻碳电极,研究了多巴胺（DA）和抗坏血酸（AA）在该电极上的电化学行为。结果表明,L-广赖氨酸单分子层修饰玻碳电极不仅能改善多巴胺和抗坏血酸的电化学行为,而且能将多巴胺和抗坏血酸二者在裸电极上的完全重叠的单氧化峰分开成为两个完全独立的氧化峰,循环伏安（CV）图上峰间距为507mV,差分脉冲伏安（DPV）图上峰间距为460mV,由此可实现在AA的共存下对样品中的DA进行选择性测定。     

反相高效液相色谱手性拆分特布他林

采用新型商品手性柱ShiseidoCD Ph,在反相条件下,对β受体阻滞剂类药物特布他林进行了手性拆分研究。考察了流动相组成、pH、柱温及缓冲盐浓度对特布它林手性拆分的影响。在优化的实验条件下,该药物获得基线分离。该方法可用于该类药物的常规分析。     

Simultaneous detection of epinephrine,uric acid,and ascorbic acid with graphene-modified electrode

A graphene-modified glassy carbon electrode was obtained via drop-casting method and applied to the simultaneous detection of epinephrine, uric acid, and ascorbic acid by cyclic voltammetry in a phosphate buffer solution (pH 3.0). The oxidation potentials of epinephrine, uric acid, and ascorbic acid were 0.484, 0.650, and 0.184 V at the graphene-modified glassy carbon electrode, respectively. The peak separation between epinephrine Pand uric acid, epinephrine and ascorbic acid, and uric acid and ascorbic acid was about 166, 300, and 466 mV, respectively. So, this graphene-modified electrode can be used for simultaneous determination of each component in a mixture.     

纳米铜修饰电极对多巴胺和抗坏血酸的同时测定

用电沉积方法制备了纳米铜修饰电极并将其用于混合溶液中多巴胺(DA)和抗坏血酸的同时测定。在优化的实验条件下,修饰电极对多巴胺和抗坏血酸具有良好的电催化响应,多巴胺的峰电流与浓度在8.0×10-7mol/L~1.0×10-4mol/L范围内成很好的线性关系,抗坏血酸的氧化峰电流与其浓度在8.0×10-6mol/L~1.0×10-3mol/L的范围成良好的线性关系。该修饰电极制备简单、稳定性好,用于样品检测,效果良好。     

Carbon fiber microelectrodes electrocoated with polycarbazole and poly(carbazole-co-p-tolylsulfonyl pyrrole) films for the detection of dopamine in presence of ascorbic acid

Polycarbazole (PCz) and poly(carbazole-co-p-tolylsulfonyl pyrrole) (PCz-co-p-Tsp) films were electrochemically deposited on single carbon fiber microelectrodes using LiClO₄ as electrolyte and acetonitrile as a solvent. The response of the sensors was tested towards different dopamine concentrations. The effect of ascorbic acid on the dopamine signal was analyzed by differential pulse voltammetry. Sensors displaying amperometric response to dopamine concentrations with a detection limit of 0.27 μM dopamine (3S/N) for the PCz modified CFE and 0.5 μM dopamine (3S/N) for the PCz-co-p-Tsp modified CFE; and an efficient protection against ascorbic acid interference at physiology concentration values (500 μM) were obtained. Correspondence: Wolfgang Schuhmann, Analytische Chemie, Elektroanalytik & Sensorik, Ruhr-Universit?t Bochum, D-44780 Bochum, Germany     

PDMS-based gold electrode for sensing ascorbic acid

Electrode with optical shapes is appreciated in microfluidics. In this article, we reported a flexible poly(dimethylsiloxane) (PDMS)-based gold electrode for ascorbic acid detection. Gold nanoparticles were chemically deposited on PDMS and the composite film was applied as working electrode. The electrode could undergo deformation and display good response performance without damage. This biosensor could give quick response to ascorbic acid (AA) (<5s) and the currents were linear with concentrations of AA in range of 0.023-7.00 mM and 30-100 mM, respectively. Limit of detection was 0.008 mM (S/N=3). This biosensor has been applied to determine ascorbic acid content in vitamin C tablets and the results were consistent with traditional iodometric method.     

Selective detection of dopamine with poly(diphenylamine sulfonic acid) modified electrode in the presence of ascorbic acid

A glassy carbon electrode was modified with electropolymerized film of diphenylamine sulfonic acid (DPASA). Electropolymerization was performed by cyclic voltammetry in 0.1 M KCl solution. The modified electrode showed an excellent electrocatalytic effect towards oxidation of dopamine (DA) and ascorbic acid (AA). Electrostatic interaction between the negatively charged poly(DPASA) film and either cationic DA species or anionic AA species favorably contributed to the redox response of DA and AA. Anodic peaks of DA and AA in their mixture were well separated by ca 168 and −11.8 mV. The proposed modified electrode was utilized for selective determination of dopamine in the concentration range of 5.0 × 10^t7–2.0 × 10⁻⁵ M in the presence of high concentration of ascorbic acid. Detection limit was 6.5 × 10⁻⁹ M.     

Electrocatalytic performance of cobalt microparticles film-modified platinum disk electrode for amperometric detection of ascorbic acid

Deposited cobalt microparticales (Co-MPs) film onto the platinum disk electrode has been successfully used as a new amperometric sensor for the determination of ascorbic acid (AA). AA is detected by surface catalyzed oxidation involving cobalt(III) oxyhydroxides in alkaline solution. The Co-MPs/Pt electrode exhibits a high electrocatalytic activity toward the AA oxidation. The diffusion coefficient of AA (6.09 × 10⁵ cm²/s) and the catalytic rate constant (k _cat = 6.27 × 10³ M^–1s^–1) have been determined using electrochemical approaches. The amperometric response of the modified electrode is linear against the AA concentration in the range (0.01?0.48 mM). The sensor displays the best activity with a high response signal, a good sensitivity of 74.3 μA/mM, a low detection limit of 2.5 μM (signal/noise = 3) and a fast response time (<3 s). Moreover, the reproducibility, selectivity and applicability of this biosensor are satisfactorily evaluated.     

A chitosan-multiwall carbon nanotube modified electrode for simultaneous detection of dopamine and ascorbic acid.

A chemically modified electrode based on a chitosan-multiwall carbon nanotube (MWNT) coated glassy carbon electrode (GCE) is described, which exhibits an attractive ability to determine dopamine (DA) and ascorbic acid (AA) simultaneously. The modified electrode exhibited a high differential pulse voltammetry (DPV) current response to DA at 0.144 V and AA at -0.029 V (vs. SCE) in a 0.1 mol l(-1) phosphate buffer solution (pH = 7.2). The properties and behaviors of the chitosan-multiwall carbon nanotube modified electrode (MC/GCE) were characterized using cyclic voltammetry (CV) and DPV methods. The mechanism for the discrimination of dopamine from ascorbic acid at MC/GCE is discussed. The linear calibration range for DA and AA were 5 x 10(-7) mol l(-1) to 1 x 10(-4) mol l(-1) (r = 0.997), and 5 x 10(-6) mol l(-1) to 1 x 10(-3) mol l(-1) (r = 0.996), respectively. The MC/GCE showed good sensitivity, selectivity and stability.     

Flow injection amperometric detection of ascorbic acid using a Prussian Blue film-modified electrode

The PB film-modified electrode was used as an amperometric detector for flow injection analysis of ascorbic acid. The modified electrode detector showed good sensitivity, stability and reproducibility. The calibration curve for ascorbic acid was linear over the concentration range from 5.0x10(-6) to 1.0x10(-3) mol l(-1) with a slope of 19.9 mA mol(-1) per litre and a correlation coefficient of 0.999. The detection limit of this method was 2.49x10(-6) mol l(-1). The relative standard deviation of six replicate injections of 2.5x10(-4) mol l(-1) ascorbic acid was 2.5%. The results obtained for ascorbic acid determination in pharmaceutical products are in good agreement with those obtained by using the procedure involving the reaction between triiodide and ascorbic acid.     

Fabrication of a template-synthesized gold nanorod-modified electrode for the detection of dopamine in the presence of ascorbic acid

Gold nanorods (GNRs) with suitable aspect ratio were synthesized with a template technique and then dispersed in a saturated sodium citrate solution by ultrasonication to form a GNR suspension. A GNR-modified electrode was fabricated using the GNR suspension. The oxidation of dopamine at the GNR/GC electrode exhibited surprisingly high electrocatalytic activity and adsorption-controlled characteristics. Square-wave voltammetry was used to detect dopamine. At the GNR/GC electrode, the linear concentration range of DA is from 1 × 10⁻⁸ M to 1 × 10⁻⁷ M and the detection limit (s/n = 3) is as low as 5.5 × 10⁻⁹ M. The current sensitivity is 3.280 μA/μM, and 1000-fold ascorbic acid (AA) cannot interfere with the determination of DA. All these performances are greatly superior to those of the bare GC electrode.     

Benzoquinone modified electrode for sensing NADH and ascorbic acid

A benzoquinone modified basal plane pyrolytic graphite electrode shows electrocatalytic activity for the oxidation of NADH and ascorbic acid in phosphate buffer (pH 7.3). The modified electrode shows a linear variation of catalytic current with concentration in the range 1-10 mM for both NADH and ascorbic acid. The rate constants have been estimated from the surface coverage data.