Fluorescent detection of amidinium-carboxylate and amidinium formation using anthracene-based diamidine: an application for the analysis of dicarboxylic acid binding

An anthracene-based diamidine (1) ‘turn-on’ fluorescent probe for the detection of dicarboxylic acids has been designed and synthesized. The fluorescence spectra of the diamidine 1 with carboxylic acids that showed two different fluorescence bands, which corresponded to the amidinium-carboxylate (λ_em=430-440 nm), and amidinium (λ_em=460-470 nm as a broad band) formation, were confirmed by DOSY NMR and TD-DFT calculations. These different fluorescence bands showed the binding mode of carboxylic acids and the stability of formed complexes toward diamidine 1. The fluorescent detection of amidinium-carboxylate formation using diamidine 1 was applicable to the detection of α,ω-dicarboxylic acids (C₆-C₁₃) and succeeded in the detection of α,ω-dicarboxylic acid (adipic acid) in human urine.     

Fluorescent detection of amidinium-carboxylate and amidinium formation using a 1,8-diphenylnaphthalene-based diamidine: dicarboxylic acid recognition with high fluorescence efficiency

A 1,8-diphenylnaphthalene-based diamidine (1) ‘turn-on’ fluorescent probe for the detection of dicarboxylic acids has been designed and synthesized. The fluorescence spectra of the diamidine 1 with carboxylic acids that showed two different fluorescence bands, which corresponded to the amidinium-carboxylate (λ_em=410–430 nm) and amidinium (λ_em=440–470 nm as a broad band, which consisted from two peaks) formation, were confirmed by DOSY NMR and TD-DFT calculations. The complexation of diamidine 1 with dicarboxylic acids, which have sufficient distances between the two carboxylic groups for binding to the diamidine 1 (dicarboxylic acids 3, 4, and α,ω-dicarboxylic acids 6 (C₆–C₂₀)), showed the formation of 1:1 complexes (i.e., amidinium-carboxylate formation). On the other hand, for the complexation with monocarboxylic acids and dicarboxylic acids having insufficient distances between the two carboxylic groups (benzoic acid 5, acetic acid 7, and α,ω-dicarboxylic acids 6 (C₃–C₅)), formation of the amidinium (1·2H⁺) was observed. Relatively similar binding constants (10⁻⁵) for the complexation of the diamidine 1 with dicarboxylic acids 6, which depend on their chain length (strain), were observed due to the flexibility of the 1,8-diphenylnaphthalene unit. Additionally, for the complexation of the diamidine 1 with dicarboxylic acids, higher fluorescence quantum yields (Φ_fl: up to 80%) were observed when compared to the binding of the diamidine 2 (Φ_fl: up to 35%).     

Carboxylic acid recognition of diamidine having a fluorescent 1,8-diphenylanthracene unit and its detection of amidinium-carboxylate and amidinium formation

A diphenylanthracene-based diamidine (1a) fluorescent probe for the detection of dicarboxylic acids has been designed and synthesized, which has an extended π-conjugation rather than a simple anthracene ring, in order to observe highly different fluorescence wavelengths after complex formation with dicarboxylic acids. The fluorescence spectra of the mixed solution of the diamidine 1a and carboxylic acids showed two different fluorescence bands, which corresponded to the complex formation (amidinium-carboxylate formation, λ_em?=?450?nm, light blue color) and dissociated amidinium formation (λ_em?=?510?nm as a broad band, green color). The complexed and dissociated states were confirmed by DOSY NMR and TD-DFT calculations. These different fluorescence wavelengths may come from the differences in the dihedral angles between the phenyl rings at the 1,8-position and anthracene ring (difference in π-conjugation) of 1a under complex formation and dissociated amidinium formation. The proposed mechanism for the observation of the different fluorescence wavelengths (complex formation and amidinium formation) was also confirmed by the fluorescence study of diamidine 1b which causes restricted rotation of the phenyl rings by substitution of the steric methyl groups, and observed the same fluorescence spectra for the complex formation and amidinium formation (400, 420, 450?nm as a vibrational structure of anthracene ring). These fluorescence characteristics of the diamidine 1a are also applicable for the detection of α,ω?dicarboxylic acids.     

The fluorescence of ellagic acid and its borax complex

The absorption and fluorescence properties of the plant phenol ellagic acid have been studied in alcohol and aqueous solutions. Fluorescence is weak in all kinds of solvents, but is greatly enhanced by addition of borax. The resulting complex emits much more intensely in methanol than in water solution. UV and fluorescence data reveal that the complex formed in methanol is different from the complex formed in aqueous solution. The enormous fluorescence enhancement of ellagic acid by borax offers a simple method for the visualization and quantification of the potent anti-mutagen ellagic acid as well as a fluorimetric method for the determination of boron.The IUPAC name for ellagic acid is 2,3,7,8-tetra-hydroxy[1]benzopyrano[5,4,3—c,d,e][1]-benzopyran-5,10-dione.     

HPLC determination of carminic acid in foodstuffs and beverages using diode array and fluorescence detection

Summary Carmine extracted from cochineal insects is one of the most used natural colorings for beverages and other foods. Its active ingredient is carminic acid (7-β-D-glucopyranosyl-9,10-dihydro-3,5,6,8-tetrahydroxy-1-methyl-9,10-dioxo-2-anthracenecarboxylic acid). This work describes a rapid HPLC determination of carminic acid and compares diode array and fluorescence detections for quantification. Samples with higher protein levels, such as milk and yogurt, are first treated with 1 mL of 8 M NH₄OH (5 min), the pH is reduced to 2 with 6 M HCl before centrifugation, the supernatant is then filtered and injected into the chromatograph. Low protein samples are simply filtered before injection. The separations were performed with a LiChroCART RP18 column using a mixture of acetonitrile and formic acid as mobile phase. The optimized conditions permit baseline quantification of the carminic acid even in the presence of other coloring agents. The sampling and analytical procedures are considerably faster than those of the literature and present excellent recuperation, selectivity, accuracy and precision. The method was applied to analysis of several yogurts and beverages. Presented at the 21^st ISC held in Stuttgart, Germany, 15^th–20^th September, 1996     

Recent advances in fluorescence sensor for the detection of peroxide explosives

The detection of peroxide explosives (PEs) has attracted considerable attention all over the world in global security owing to their simple preparation, poor chemical stability and easy decomposition. In recent years, great efforts have been devoted to developing organic fluorescence sensors for detecting the PEs because of their fast response, high sensitivity and high selectivity. In this short review, we firstly discuss the sensing mechanisms for fluorescence based the PEs detection. Next, we reviewed recent progress of PE probes in the nearly 5 years and the design strategies of the material structures to enhance the sensitivity or selectivity, such as conjugated polymers and assembled nanoparticles.     

Cu triggered fluorescence sensor based on fluorescein derivative for Pd detection

This Letter describes the synthesis of a novel fluorescein-based derivative used as the fluorescence sensor for Pd²⁺ detection. The sensor can show highly selective and sensitive ‘off-on’ fluorescence response only in the presence of Cu²⁺ as a synergic trigger, which presents a new strategy for Pd²⁺ detection method.     

High-performance liquid chromatographic assay with fluorescence detection for the evaluation of inhibitors against fatty acid amide hydrolase

A fluorescent assay for the evaluation of inhibitors of fatty acid amide hydrolase (FAAH) is described. Microsomes from rat brain served as enzyme source. N-(2-Hydroxyethyl)-4-pyren-1-ylbutanamide was designed and synthesized as novel fluorogenic substrate. For substrate solubilization, Triton X-100 was employed. The FAAH activity was determined directly without further sample clean-up by measuring the amount of 4-pyren-1-ylbutanoic acid released by the enzyme with reversed-phase HPLC and fluorescence detection. The known FAAH inhibitors URB597, phenyl hexanoyl oxazolopyridine (PHOP) and [6-(2-methyl-4,5-diphenyl-1H-imidazol-1-yl)hexyl]carbamic acid phenyl ester were used to validate the test assay.     

HPLC of 9-fluorenylmethylchloroformate-polyamine derivatives with fluorescence detection

Summary There are a number of reagents available for fluorescent labelling of primary amines. These include dansyl chloride, o-phthalaldehyde, fluorescamine, and a new reagent, 9-fluorenylmethylchloroformate (FMOC), reported recently. This paper describes a reversed-phase HPLC procedure for the separation and fluorescence detection of polyamines following pre-column derivatization with FMOC. The polyamines studied by this method include putrescine, cadaverine, spermidine, and spermine. Experiments were carried out to determine maximum fluorescence excitation and emission wavelengths, optimum reaction pH, linear ranges, and minimum detection limits for each of the polyamines. The HPLC method includes a gradient program which provides complete separation from serum hydrolysate components and specificity for the four polyamines with detection limits ranging from 2 to 9 pg. This procedure was applied to hydrolyzed serum samples.     

高效液相色谱-荧光检测法测定人体尿液中的蝶呤-6-羧酸

利用蝶呤-6-羧酸具有天然荧光的特点,建立了人体尿液中蝶呤-6-羧酸的高效液相色谱-荧光分析方法。尿液经硫酸铵处理后,过0.45μm水相滤膜,直接进行液相色谱分析,色谱柱为NOVA-PAK C18柱,保护柱为RCSS Guard-PAKTMC18柱,流动相为V(5 mmol/L KH2P04-NaOH缓冲溶液,pH 7.3)∶V(甲醇)=99∶1),流速为0.6 mL/min,荧光激发波长为338 nm,荧光发射波长为420nm。蝶呤-6-羧酸在0.05~1.2μg/mL范围内呈线性关系,相关系数为0.9974,检出限为0.010μg/mL。分别添加0.625、2.50和4.50μg蝶呤-6-羧酸标准品,平均回收率(n=5)在99.7%~105%之间,相对标准偏差小于3.6%。此法可用于临床尿样中蝶呤-6-羧酸的分析。     

Identification of catecholamine neurotransmitters using fluorescence sensor array

A nano-based sensor array has been developed for identification and discrimination of catecholamine neurotransmitters based on optical properties of their oxidation products under alkaline conditions. To produce distinct fluorescence response patterns for individual catecholamine, quenching of thioglycolic acid functionalized cadmium telluride (CdTe) quantum dots, by oxidation products, were employed along with the variation of fluorescence spectra of oxidation products. The spectral changes were analyzed with hierarchical cluster analysis (HCA) and principal component analysis (PCA) to identify catecholamine patterns. The proposed sensor could efficiently discriminate the individual catecholamine (i.e., dopamine, norepinephrine, and l-DOPA) and their mixtures in the concentration range of 0.25–30 μmol L⁻¹. Finally, we found that the sensor had capability to identify the various catecholamines in urine sample.     

Turn-on fluorescence sensor based on the aggregation of pyrazolo[3,4-b]pyridine-based coumarin chromophores induced by Hg

We developed a new fluorescent sensor (PPC-S) for Hg²⁺ based on the aggregation-induced emission (AIE) of pyrazolo[3,4-b]pyridine-based coumarin chromophore (PPC-O). Given the desulfurization reaction with Hg²⁺, AIE inactive PPC-S can be transformed into PPC-O with AIE activity, which can be employed for the fluorescence turn-on detection of Hg²⁺ with satisfactory selectivity and sensitivity in aqueous solutions.     

荧光光谱法测定氨基酸的新方法

在醋酸 醋酸钠缓冲介质中 ,氨基酸能猝灭壳聚糖 茚三酮体系的荧光。基于此 ,建立了一种新的荧光光谱测定氨基酸的方法 ,探讨了其反应机理及测定条件。方法的线性范围为 0mol·L- 1 ～ 1 2× 1 0 - 4 mol·L- 1 ,已应用于测定果汁饮料     

Optimising oxygen-sensitivity of optical sensor using pyrene carboxylic acid by myristic acid co-chemisorption onto anodic oxidized aluminium plate

Optical oxygen-sensitivity using pyrene carboxylic acid with long alkyl chain (1-pyrenedecanoic acid and 1-pyrenedodecanoic acid) and myristic acid co-chemisorption layer was controlled by varying the molar ratio of myristic acid to pyrene carboxylic acid. The ratio I₀/I₁₀₀, where I₀ and I₁₀₀ represent the detected fluorescence intensities from a substrate exposed to 100% argon and 100% oxygen, respectively, is used as an indicator of the sensitivity of the sensing film. At a composition ratio of 1 pyrene carboxylic acid to 10 myristic acids, the I₀/I₁₀₀ attained its maximum value and then the ratio decreased with increase in the molar ratio of myristic acid to pyrene carboxylic acid. The Stern-Volmer constant (K_SV) also attained its maximum value at a composition ratio of one pyrene carboxylic acid to ten myristic acids and then the ratio decreased with increase in the molar ratio of myristic acid to pyrene carboxylic acid. The oxygen-sensitivity of optical sensor using pyrene carboxylic acid is optimized by myristic acid co-chemisorption.     

Electrochemical,fluorescence, and UV detection for HPLC analysis of various cysteine derivatives

Electrochemical (ECD), fluorescence (FLD), and UV spectrophotometric (UVD) detection were used to monitor various S-alk(en)yl-L -cysteines and their corresponding sulfoxide isomers following pre-column derivatization with o-phthaldialdehyde-tert-butylthiol and separation by reversed-phase HPLC. Recording of hydrodynamic voltammograms, FLD stop-flow scanning, and on-line captured UV spectra were methods used for establishing optimal detector settings which were defined as a compromise between favorable selectivity and high sensitivity. Optimal detector settings were found at: (A) 750 mV vs. Ag/AgCl for ECD; (B) excitation at 230 nm and emission at 420 nm for FLD; and (C) 337 nm for UVD. Various aspects of detector practicability such as selectivity, baseline disturbances due to excessive reagent, scanning possibilities, as well as detection limits were evaluated and compared. Minimal detectable amounts of the compounds were in the range of 130-160 fmol for ECD, and 2.5-3.5 pmol and 13-16 pmol for FLD and UVD. In addition, the possibilities and benefits of detector coupling were examined.     

Supramolecular networks constructed from mono- and bi-nuclear lanthanide complexes with 1,2-phenylenedioxydiacetic acid

[Tb₂(1,2-pdoa)₃ · 6H₂O] · H₂O (1) and [La(1,2-pdoa)(1,2-H₂pdoa)(OH) · H₂O] · 5H₂O (2) (1,2-H₂pdoa = 1,2-phenylenedioxydiacetic acid) have been synthesized and structurally characterized by single crystal X-ray diffraction. Complex 1 is a binuclear molecule in which one 1,2-pdoa ligand is a tetradentate bridge linking two Tb³⁺ ions, the other two 1,2-pdoa ligands bond Tb1³⁺ and Tb1A³⁺ via tetradentate chelating coordination. Tb³⁺ is nine-coordinate by six oxygens of 1,2-pdoa and three waters. Complex 2 is mono-nuclear with La³⁺ ten-coordinate by eight oxygens of two 1,2-pdoa, one hydroxide and one water. 1,2-Pdoa is tetradentate chelating with La³⁺ ion. The packing diagrams of 1 and 2 show supramolecular networks via H-bonds. The fluorescence spectrum of 1 shows characteristic emission of Tb³⁺ with ⁵D₄ → ⁷F_j (j = 6–3) transitions.     

Label-free and fluorescence turn-on aptasensor for protein detection via target-induced silver nanoclusters formation

A simple turn-on and homogeneous aptasensor, which relies on target induced formation of silver nanoclusters (Ag NCs), was developed for the determination of platelet-derived growth factor B-chain homodimer (PDGF-BB). The aptasensor contains two hairpin DNA probes termed as P1 and P2. P1 consists of the aptamer sequence of PDGF-BB. Meanwhile, P2 contains the Ag NCs nucleation sequence, which is blocked by the hairpin stem region. P1 and P2 can co-exist metastably in the absence of PDGF-BB and maintain hairpin structure. However, in the presence of PDGF-BB, the binding of PDGF-BB with aptamer will result in the hybridization between P1 and P2, and release the Ag NCs nucleation sequence. In this case, Ag NCs can be formed via the reduction of Ag⁺ by NaBH₄. By monitoring the increase in fluorescence intensity, we could detect the target protein with high sensitivity. The detection limit of this aptasensor is 0.37 nM, which is comparable with that of other reported aptasensors. Furthermore, this proposed aptasensor shows high selectivity toward its target protein. Thus, the proposed aptasensor based on target induced formation of Ag NCs could be used as a sensitive and selective platform for the detection of target protein.     

Asymmetric synthesis of phosphonic acid analogues for acylcarnitine

Phosphonic acid analogues of acylcarnitine were prepared in an optically active form expecting CPT I inhibitory activities. The synthetic methodology was based on catalytic asymmetric dihydroxylation of β,γ-unsaturated phosphonates and subsequent regioselective amination via the cyclic sulfates.     

Quantum dot-based immunosensor for the detection of prostate-specific antigen using fluorescence microscopy

A sensitive optical method based on quantum dot (QD) technology is demonstrated for the detection of an important cancer marker, total prostate-specific antigen (TPSA) on a disposable carbon substrate surface. Immuno-recognition was carried out on a carbon substrate using a sandwich assay approach, where the primary antibody (Ab)-protein A complex covalently bound to the substrate surface, was allowed to capture TPSA. After the recognition event, the substrate was exposed to the biotinylated secondary Abs. After incubation with the QD streptavidin conjugates, QDs were captured on the substrate surface by the strong biotin-streptavidin affinity. Fluorescence imaging of the substrate surface illuminated the QDs, and provided a very sensitive tool for the detection of TPSA in undiluted human serum samples with a detection limit of 0.25 ng/mL. The potential of this method for application as a simple and efficient diagnostic strategy for immunoassays is discussed.