Microwave Effects Due to Anionic or Cationic Initiators in Emulsion Polymerization Reactions

Summary: Emulsion polymerization reactions were performed under microwave irradiation and conventional heating using anionic or cationic initiators and surfactants. Microwave irradiation promoted higher reaction rates for both initiators and surfactants, in comparison with the conventional heating. The effect of high power microwave irradiation was studied using a method of cycles of heating and cooling, where rapid polymerization reactions were obtained. In the reactions with anionic initiator and surfactant, a decrease in the particle diameters was observed with microwave heating, and even smaller particles were obtained using high power microwave irradiation. Moreover, the decrease in the particle size was acompanied by an increase in the polymer molecular weight. On the other hand, these effects were not observed for reactions with cationic initiator and surfactant.     

Multicomponent cyclocondensation reactions of aminoazoles, arylpyruvic acids and aldehydes with controlled chemoselectivity

The multicomponent reactions of 3-amino-1,2,4-triazoles/5-aminotetrazole with phenylpyruvic acids and aromatic aldehydes were studied using conventional thermal heating, ultrasonification and microwave dielectric heating. Two different reaction pathways for these cyclocondensations occurring under either kinetic or thermodynamic control were established depending on the temperature regime and building block selection. In case of aminotriazoles, an unprecedented reaction pathway leading to 5-aryl-7-hydroxy-6-phenyl-4,5,6,7-tetrahydro[1,2,4]triazolo[1,5-a]pyrimidine-7-carboxylic acids was found and discussed.     

Synthesis of pyrrole and indole quinoxalinone and oxazinone derivatives by intramolecular copper-catalyzed reactions

Intramolecular N-arylation of pyrrole and indole carboxamides and carboxylates linked with a pendant haloarene by Cu-catalyzed reactions to synthesize pyrrole and indole quinoxalinone and oxazinone derivatives is reported. The ring closure reactions were carried out by conventional heating and MW irradiation. The use of conventional heating affords moderate to good yields of the quinoxalinone and oxazinone derivatives (34-72%), while by using MW heating the best results are obtained (41-99%).     

Microwave-assisted selective protection of glutaraldehyde and its symmetrical derivatives as monoacetals and -thioacetals

Six monoprotected acetals and -thioacetals of glutaradehyde and its symmetrical dimethyl derivatives were synthesized. Microwave-assisted heating proved to be a substantially more selective method for monoprotection than conventional heating. All reactions were efficient and only traces of diprotected material were formed.     

Microwave-assisted SNAr reaction of 2,4,6-trichloro-1,3,5-triazine for the rapid synthesis of C3-symmetrical polycarboxylate ligands

The microwave-assisted S_NAr reaction of 2,4,6-trichloro-1,3,5-triazine with various unprotected amino acids was developed for the synthesis of C₃-symmetrical polycarboxylate ligands which can be used as structural directing units in metal-organic frameworks. The reactions were performed in water using a domestic microwave oven as the heating device. In comparison to the reactions performed under conventional heating, the reactions under microwave irradiation proceeded much more rapidly within 20 min to afford the desired ligands in comparative yields to those obtained by conventional heating.     

Inductive heating with magnetic materials inside flow reactors

Superparamagnetic nanoparticles coated with silica gel or alternatively steel beads are new fixed-bed materials for flow reactors that efficiently heat reaction mixtures in an inductive field under flow conditions. The scope and limitations of these novel heating materials are investigated in comparison with conventional and microwave heating. The results suggest that inductive heating can be compared to microwave heating with respect to rate acceleration. It is also demonstrated that a very large diversity of different reactions can be performed under flow conditions by using inductively heated flow reactors. These include transfer hydrogenations, heterocyclic condensations, pericyclic reactions, organometallic reactions, multicomponent reactions, reductive cyclizations, homogeneous and heterogeneous transition-metal catalysis. Silica-coated iron oxide nanoparticles are stable under many chemical conditions and the silica shell could be utilized for further functionalization with Pd nanoparticles, rendering catalytically active heatable iron oxide particles.     

Anti-Markovnikov hydroaminations of styrene catalyzed by palladium(II) N-heterocyclic carbene complexes under conventional and microwave heating

Six palladium(II) complexes with benzimidazole-based N-heterocyclic carbene ligands were synthesized by transmetallation reactions between silver(I) N-heterocyclic carbene complexes and PdCl₂(PhCN)₂. The complexes were characterized by physicochemical and spectroscopic methods. The palladium complexes were tested as catalysts for intermolecular hydroamination reactions of styrene with various anilines in ionic liquids under both conventional and microwave heating. All of these complexes proved to be catalytically active in these reactions. The anti-Markovnikov addition products were selectively obtained by using 1 mol% of the palladium complex.     

A comparison of microwave-accelerated and conventionally heated iodination reactions of some arenes and heteroarenes, using ortho-periodic acid as the oxidant

A fast and simple method for the oxidative iodination of some activated arenes and heteroarenes, either under microwave irradiation or by conventional heating, is reported, using diiodine and ortho-periodic acid as the oxidant. The reactions were carried out in hot 95% ethanol under a reflux condenser. For the microwave assisted reactions, the reaction times were always notably shortened, but the yields were nearly the same as those afforded by the conventional method.     

Microwave-assisted asymmetric organocatalysis. A probe for nonthermal microwave effects and the concept of simultaneous cooling

A series of five known asymmetric organocatalytic reactions was re-evaluated at elevated temperatures applying both microwave dielectric heating and conventional thermal heating in order to probe the existence of specific or nonthermal microwave effects. All transformations were conducted in a dedicated reactor setup that allowed accurate internal reaction temperature measurements using fiber-optic probes. In addition, the concept of simultaneous external cooling while irradiating with microwave power was also applied in all of the studied cases. This method allows a higher level of microwave power to be administered to the reaction mixture and, therefore, enhances any potential microwave effects while continuously removing heat. For all of the five studied (S)-proline-catalyzed asymmetric Mannich- and aldol-type reactions, the observed rate enhancements were a consequence of the increased temperatures attained by microwave dielectric heating and were not related to the presence of the microwave field. In all cases, in contrast to previous literature reports, the results obtained either with microwave irradiation or with microwave irradiation with simultaneous cooling could be reproduced by conventional heating at the same reaction temperature and time in an oil bath. No evidence for specific or nonthermal microwave effects was obtained.     

微波与有机化学反应的选择性

本文综述了微波辅助下有机化学反应的选择性,包括化学选择性、区域选择性、顺反选择性、非对映选择性、对映选择性,与传统加热条件下反应选择性的区别。讨论了微波对有机化学反应选择性的影响。从文献报道的结果来看,虽然观察到了一些反应在微波照射与加热条件下显示出不同的选择性,但绝大部分例子并不是在严格相同的条件下进行的对比,还有一些虽然做了对比研究,但却忽略了温度的影响。对于绝大多数例子,微波产生的选择性的差别似乎都可以用热效应来解释。可以认为微波辅助的反应中基本不存在特殊的"非热效应"。微波辅助技术可以通过改变反应温度来实现改变某些反应的选择性。希望本文对微波效应和微波对有机反应加速效应的本质的理解提供一些有用信息。     

Switchable selectivity in multicomponent heterocyclizations of acetoacetamides, aldehydes, and 3-amino-1,2,4-triazoles/5-aminopyrazoles

Multicomponent heterocyclizations of 3-amino-1,2,4-triazoles/5-aminopyrazoles with acetoacetamides and aromatic aldehydes were studied in detail using conventional thermal heating, ultrasonication, and microwave irradiation. Several different synthetic pathways for these cyclocondensations occurring under either kinetic or thermodynamic control were established depending on the temperature regime and building block selection. The experimental data obtained and the procedures developed allow tuning selectivity of the multicomponent reactions studied.     

新型氨基甲酸含氮杂环甲基酯的合成及生物活性研究

常规加热或微波照射下, 含氮杂环1与多聚甲醛反应以良好的产率生成含氮杂环基甲醇3, 反应物物质的量的比、反应温度等对反应产率有影响, 微波条件下的反应时间比常规加热下大大缩短. 化合物3和异氰酸酯4在常规加热或微波照射下生成相应的氨基甲酸含氮杂环甲基酯5a～5m. 反应温度、反应物物质的量的比、反应时间、微波辐射功率等对反应产率都有一定的影响, 与常规加热相比微波条件下的反应时间大大缩短. 化合物5的结构经过IR, ¹H NMR, MS, 元素分析测定, 部分化合物经过¹³C NMR测定. 测定了化合物5的杀虫和除草活性, 结果表明其杀虫活性较低, 除草活性高于杀虫活性, 5a, 5d, 5e和5m对苋菜和黄瓜的防除率高达100%.     

Sulfuric acid catalyzed addition of β-dicarbonyl compounds to alcohols under conventional heating and microwave-assisted conditions

The highly efficient direct addition of β-dicarbonyl compounds to secondary alcohols has been achieved using one of the cheapest acids, H₂SO₄, as the catalyst. For a series of β-dicarbonyl compounds and various secondary alcohols, the addition reactions all complete in 5 min with high yields both under the conventional heating condition and under the microwave heating condition. The comparison of the results obtained from the microwave heating condition with those obtained from the conventional heating condition shows that no obvious specific or nonthermal microwave effects exist in the microwave-assisted addition reactions.     

Microwave-accelerated or conventionally heated iodination reactions of some aromatic amines, using ortho-periodic acid as the oxidant

A fast and simple method for the oxidative iodination of some aromatic amines, either under microwave irradiation or conventional heating, is reported, using diiodine and ortho-periodic acid as the oxidant. The reactions were carried out in boiling CH2Cl2 solutions under a reflux condenser. For the microwave assisted reactions, the reaction times were always notably shortened, but the yields were usually less influenced as compared with the conventional method.     

Microwave synthesis of zeolites. 2. Effect of vessel size, precursor volume, and irradiation method

The enhancement of synthesis reactions under microwave heating is dependent on many complex factors. We investigated the importance of several reaction engineering parameters relevant to microwave synthesis. Of interest to this investigation were the reaction vessel size, volume of precursor reacted, microwave power delivery, and microwave cavity design. The syntheses of NaY zeolite and beta-zeolite were carried out under a number of varying conditions to determine the influence of these parameters on the nucleation rate, the crystallization rate, and the particle size and morphology. The rates of NaY and beta-zeolite nucleation and crystallization were more rapid in the multimode CEM MARS-5 oven compared to the more uniform field CEM Discover. The faster synthesis rate in the MARS-5 may be the result of the multimode microwave electric field distribution. Slower rates of NaY and beta-zeolite formation observed in the Discover and a circular waveguide may be the result of a more uniform microwave electric field distribution. Changes in reaction vessel size and precursor volume during the microwave synthesis of beta- and NaY zeolite were found to influence the rate of zeolite formation. These results indicate that reactor geometry needs to be considered in the design of systems used for microwave synthesis. Comparative synthesis reactions were carried out with conventional heating, and microwave heating was shown to be up to over an order of magnitude faster for most of these syntheses.     

Microwave-assisted benzyne-click chemistry: preparation of 1H-benzo[d][1,2,3]triazoles

The benzotriazoles were prepared by three-component and two-component microwave-assisted [3+2] cycloadditions of various azides to benzyne, 3-methoxybenzyne, and 4,5-difluorobenzyne. In the three-component reaction, the aryne is generated, in the presence of an azide prepared in situ, by the reaction of an o-(trimethylsilylaryl) triflate with either CsF or KF/18-Crown-6. However, in the two-component reactions, a freshly prepared azide is added to the reaction vessel prior to aryne generation. Good to excellent yields of benzotriazoles were obtained in 15-20 min when the microwave-assisted reactions were carried out at 125 °C. These reaction times are significantly faster than similar reactions carried out using conventional heating.     

A convenient strategy of dimerization by microwave heating and using 2,5-diketopiperazine as scaffold

A novel and convenient microwave-assisted dimerization of an active peptide compound using the DKPs as scaffold is described. The key reaction giving rise to the diketopiperazine scaffold is the intermolecular coupling. No epimerization was detected in the reactions used. Conventional and microwave heating of the reactions are compared. Synthesis by microwave irradiation gave the desired compounds in higher yields and in shorter reaction times than those obtained by conventional heating.     

CARO'S ACID SUPPORTED ON SILICA GEL. PART 7: A VERSATILE REAGENT FOR THE AROMATIZATION OF HANTZSCH 1,4-DIHYROPYRIDINES UNDER NON-AQUEOUS CONDITION AND MICROWAVE IRRADIATION

Efficient oxidation of 1,4-dihydropyridines with Caro's acid on silica gel is achieved under nonaqueous conditions and in a domestic microwave oven. The reactions under microwave irradiation were shorter in duration and higher in yields than the reactions in conventional method, confirming the potentiality of microwave heating in aromatization of Hantzsch 1,4-dihydropyridines.     

Characterization and study of microwave activation effects on the polystyrene tacticity

¹³C Nuclear magnetic resonance proved to be an advantageous tool to determine the stereoregularity of polystyrene polymers. The latter was achieved through the analysis of the signal of the quaternary carbon and that of the carbon-p in the aromatic ring too. Styrene was polymerized through microwaves and conventional heating activation using two different polymerization techniques: emulsion and bulk. Microwave activation was performed in a mono-modal type device under the following experimental conditions: various initiator concentrations, an average irradiation power of 50?W, temperature of 70°C, and using a batch reactor for emulsion and bulk experiments. The results obtained in these experiments were compared with those obtained by conventional heating activation polymerization under the same initiator concentration and temperature conditions. Microwave-activated reactions resulted in shorter reaction times and higher yields. The tacticity of the polymer samples was not significantly altered, which lead to the conclusion that, in this case, the stereoregularity of polystyrene was not influenced by microwave irradiation.     

Copper-catalyzed alkyne-aryne coupling reaction under microwave conditions: preparation of unsymmetric and symmetric di-substituted alkynes

Several unsymmetric and symmetric alkynes were prepared excellent to modest yields by generating benzyne from the reaction of 2-(trimethylsilyl)phenyl triflate with CsF in the presence of CuI and terminal alkyne under microwave heating for 30 min at 150 °C. Using conventional heating, the reactions required 24 h reaction time.