N+BF<Subscript>2</Subscript> and N+C+BF<Subscript>2</Subscript> high-dose co-implantation in silicon

Nitrogen and boron BF₂, and nitrogen, carbon, and boron BF₂ high-dose (6×10¹⁶–3×10¹⁷ cm^-2) co-implantation were performed at energies of about 21–77 keV. Subsequent high-temperature annealing processes (600, 850, and 1200 °C) lead to the formation of three and two surface layers respectively. The outer layer mainly consists of polycrystalline silicon and some amorphous material and Si₃N₄ inclusions. The inner layer is highly defective crystalline silicon, with some inclusions of Si₃N₄ too. In the N+B-implanted sample the intermediate layer is amorphous. Co-implantation of boron with nitrogen and with nitrogen and carbon prevents the excessive diffusivity of B and leads to a lattice-parameter reduction of 0.7–1.0%. Received: 10 January 2002 / Accepted: 30 May 2002 / Published online: 4 November 2002 RID="*" ID="*"Corresponding author. Fax: +34-91/3974895; E-mail: Lucia.Barbadillo@uam.es     

Investigation of electrical and optical properties of ZnO thin films grown with O<Subscript>2</Subscript>/O<Subscript>3</Subscript> gas mixture

The electrical and optical properties of ZnO thin films grown with an O₂/O₃ gas mixture are compared with samples grown with pure oxygen gas. The ZnO films were grown on sapphire(0001) by pulsed laser deposition. The residual background carrier concentration is reduced by using an O₂/O₃ gas mixture as compared to pure molecular oxygen. In particular, a one order of magnitude reduction in residual background carrier density (6.15×10¹⁶ cm^-3) is achieved by using an O₂/O₃ gas mixture. The lower donor defect density is attributed to the generation of acceptor defects compensating for the residual donor defects. Photoluminescence results show that the deep level emission increased and the band edge emission decreased for the ZnO films grown with ozone, as compared to the samples grown with pure oxygen gas. PACS 73.61.Ga; 78.55Et; 81.05 Dz; 81.15.Fg     

Electric and magnetic properties of CoFe<Subscript>2</Subscript>O<Subscript>4</Subscript>/Pb(Zr<Subscript>0.52</Subscript>Ti<Subscript>0.48</Subscript>)O<Subscript>3</Subscript> bilayer thin films prepared by pulsed-laser deposition

CoFe₂O₄ (CFO) thin film with highly (111)-preferential orientation was first deposited on the silicon substrate by a pulsed-laser deposition, and then Pb(Zr_0.52Ti_0.48)O₃ (PZT) layers were deposited with different oxygen pressures to form the bilayer CFO/PZT nanocomposite thin films. X-ray diffraction showed that the PZT preferential orientation was strongly dependant on the oxygen pressure. The smooth film surface was obtained after depositing the CFO and PZT layers. The bilayer thin films exhibit good ferromagnetic and ferroelectric properties, and a low leakage current density of 0.004 μA/cm² at 50 kV/cm. The leakage current density curves show loops for the electric polarized field when the electric field reverses. PACS 77.84.Lf; 75.80+q; 81.05.Zx; 81.15.Fg     

CaCuMn<Subscript>6</Subscript>O<Subscript>12</Subscript> vs. CaCu<Subscript>2</Subscript>Mn<Subscript>5</Subscript>O<Subscript>12</Subscript>: A comparative study

The ferrimagnetic compounds Ca(Cu_xMn_3?x)Mn₄O₁₂ of the double distorted perovskites AC₃B₄O₁₂ family exhibit a rapid increase of the ferromagnetic component in magnetization at partial substitution of square coordinated (Mn³⁺)_C for (Cu²⁺)_C. In the transport properties, this is seen as a change of the semiconducting type of resistivity for the metallic one. The evolution of magnetic properties of Ca(Cu_xMn_3?x)Mn₄O₁₂ is driven by strong antiferromagnetic exchange interaction of (Cu²⁺)_C with (Mn³⁺/Mn⁴⁺)_B coordinated octahedra. The competing interactions of (Mn³⁺)_C with (Mn³⁺/Mn⁴⁺)_B lead to the formation of noncollinear magnetic structures that can be aligned by magnetic fields.     

Cooperative down-conversion of UV light in disordered scheelitelike Yb-doped NaGd(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> and NaLa(MoO<Subscript>4</Subscript>)<Subscript>2</Subscript> crystals

Concentration series of disordered scheelitelike Yb:NaGd(MoO₄)₂ and Yb:NaLa(MoO₄)₂ single crystals are grown by the Czochralski method. The actual concentrations of Yb³⁺ ions in the crystals are determined by optical-absorption spectroscopy. The luminescence of Yb³⁺ ions in these crystals in the region of 1 μm is studied under UV and IR excitation. In the case of UV excitation, this luminescence appears as a result of nonradiative excited state energy transfer from donor centers of unknown nature to ytterbium. The character of the concentration dependence of Yb³⁺ luminescence indicates that the energy transfer at high Yb concentrations occurs with active participation of a cooperative mechanism, according to which the excitation energy of one donor center is transferred simultaneously to two Yb³⁺ ions. In other words, the quantum yield of this transfer exceeds unity, which can be used to increase the efficiency of crystalline silicon (c-Si) solar cells.     

Optical absorption spectra and magnetic phase transitions in TbFe<Subscript>3</Subscript>(BO<Subscript>3</Subscript>)<Subscript>4</Subscript>

Optical absorption spectra of the trigonal crystal of TbFe₃(BO₃)₄ in the vicinity of the ⁷F₆ → ⁵D₄ transition in a Tb³⁺ ion were studied as a function of temperature (2–70 K) and magnetic field strength (0–60 kOe) at 2 K. The splitting of the excited states of Tb³⁺ due to both the magnetic ordering of iron and an external magnetic field was determined. Abrupt splitting of the absorption lines of Tb³⁺ at temperature T_N of the magnetic ordering of the subsystem of iron was revealed, suggesting that the nature of such splitting is not entirely magnetic.     

Microstructural and Radioluminescence Characteristics of Nd<Superscript>3+</Superscript> Doped Columbite-Type SrNb<Subscript>2</Subscript>O<Subscript>6</Subscript> Phosphor

Undoped and different concentration Nd³⁺ doped SrNb₂O₆ powders with columbite structure were synthesized by molten salt process using a mixture of strontium nitrate and niobium (V) oxide and NaCl-KCl salt mixture as a flux under relatively low calcining temperature. X-ray diffraction analysis results indicated that SrNb₂O₆ phases found to be orthorhombic columbite single phase for undoped, 0.5 and 3 mol% Nd³⁺ doping concentrations. Phase composition of the powders was examined by SEM-EDS analyses. Radioluminescence properties of Nd³⁺ doped samples from UV to near-IR spectral region were studied. The emissions increased with the doping concentration of up to 3 mol%, and then decreased due to concentration quenching effect. There is a sharp emission peak around 880 nm associated with ⁴F_5/2 → ⁴I_9/2 transition in the Nd³⁺ ion between 300 and 1100 nm. The broad emission band intensity was observed from 400 to 650 nm where the peak intensities increased by increasing Nd³⁺ doping concentration. All the measurements were taken under the room temperature.     

A miniature tunable TEA CO<Subscript>2</Subscript> laser using isotope <Superscript>13</Superscript>C<Superscript>16</Superscript>O<Subscript>2</Subscript> and <Superscript>12</Superscript>C<Superscript>16</Superscript>O<Subscript>2</Subscript>

A miniature tunable TEA CO₂ laser using isotope ¹³C¹⁶O₂ as the active medium is developed to extend the spectral range of CO₂ lasers for further application. The optimization of the energy parameters of the tunable TEA ¹³C¹⁶O₂ laser and the same laser using ¹²C¹⁶O₂ are studied. When a gas mixture (¹³C¹⁶O₂: N₂: He = 1: 1: 3) at a total pressure of 6.4 × 10⁴ Pa is used, the TEA ¹³C¹⁶O₂ laser of a 45-cm³ active volume obtains 51 emission lines in the [00⁰1–10⁰0] and [00⁰1–02⁰0] bands. The maximum pulse energy of the TEA ¹³C¹⁶O₂ laser is about 357 mJ. The same laser using the conventional gas mixture (¹²C¹⁶O₂: N₂: He = 1: 1: 3) at a pressure of 6.66 × 10⁴ Pa is measured to obtain 69 laser emission lines and the maximum pulse energy of laser radiation is about 409 mJ.     

Thermal sensors based on Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript> and (Sb<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>70</Subscript>(Bi<Subscript>2</Subscript>Te<Subscript>3</Subscript>)<Subscript>30</Subscript> thin films

Thin films of Sb₂Te₃ and (Sb₂Te₃)₇₀(Bi₂Te₃)₃₀ alloy and have been deposited on precleaned glass substrate by thermal evaporation technique in a vacuum of 2?×?10^?6 Torr. The structural study was carried out by X-ray diffractometer, which shows that the films are polycrystalline in nature. The grain size, microstrain and dislocation density were determined. The Seebeck coefficient was determined as the ratio of the potential difference across the films to the temperature difference. The power factor for the (Sb₂Te₃)₇₀ (Bi₂Te₃)₃₀ and (Sb₂Te₃) is found to be 19.602 and 1.066 of the film of thickness 1,500 Å, respectively. The Van der-Pauw technique was used to measure the Hall coefficient at room temperature. The carrier concentration was calculated and the results were discussed.     

Dilute ferrimagnetism of ilmenites Mn<Subscript>3</Subscript>FeTiSbO<Subscript>9</Subscript> and Mn<Subscript>4</Subscript>FeTi<Subscript>2</Subscript>SbO<Subscript>12</Subscript>

Metastable solid solutions (SS) Mn₃FeTiSbO₉ and Mn₄FeTi₂SbO₁₂ with the ilmenite structure (space group R\(\bar 3\)) have been prepared by quenching at normal conditions. The compositions of the compounds have been justified using EDX spectroscopy and X-ray diffraction. The magnetic properties of SSs have been analyzed by comparison with ferrimagnetic ilmenite Mn₂FeSbO₆ (T_N = 269 K) as a natural mineral and ceramics obtained at high pressure and high temperature. The solid solutions have been characterized as dilute magnetic systems formed as a result of substitution of nonmagnetic cations Ti⁴⁺ for a part of Fe³⁺ and Sb⁵⁺ cations. Mn₃FeTiSbO₉ is considered as a ferromagnetic with T_N = 171 K and Mn₄FeTi₂SbO₁₂ as a magnetic with the concentration of magnetic clusters below the percolation threshold.     

Studies on structural and electrical properties of Mg<Subscript>0. 5+y</Subscript> (Zr<Subscript>2-y</Subscript>Fe<Subscript>y</Subscript>) <Subscript>2</Subscript> (PO<Subscript>4</Subscript>) <Subscript>3</Subscript> ceramic electrolytes

The sample of Mg_{0. 5+y} (Zr_1-y Fe_y) ₂ (PO₄) ₃ (0.0 ≤y ≤0.5) was synthesized using the sol-gel method. The structures of the samples were investigated using X-ray diffraction and Fourier transform infrared spectroscopy measurement. XRD studies showed that samples had a monoclinic structure which was iso-structured with the parent compound, Mg_0.5Zr (PO₄) ₃. The complex impedance spectroscopy was carried out in the frequency range 1–6 MHz and temperature range 303 to 773 K to study the electrical properties of the electrolytes. The substitutions of Fe³⁺ with Zr⁴⁺ in the Mg_0.5Zr (PO₄) ₃ structure was introduced as an extrainterstitial Mg²⁺ ion in the modified structured. The compound of Mg_0.5+y (Zr_1-y Fe_y)₂(PO₄)₃ with y?=?0.4 gives a maximum conductivity value of 1.25?×?10^?5 S cm^?1 at room temperature and 7.18?×?10^?5 S cm^?1 at 773 K. Charge carrier concentration, mobile ion concentration, and ion hopping rate are calculated by fitting the conductance spectra to power law variation, σ _ac (ω)?=?σ _o ? +?Aω ^α . The charge carrier concentration and mobile ion concentration increases with increase of Fe³⁺ inclusion. This implies the increase in conductivity of the compounds was due to extra interstitial Mg²⁺ ions.     

Synthesis and characterization of mono-dispersed Y<Subscript>3</Subscript>Al<Subscript>5</Subscript>O<Subscript>12</Subscript>:Er<Superscript>3+</Superscript>-coated SiO<Subscript>2</Subscript> nanoparticles by co-precipitation process

In this paper, a facile co-precipitation process for preparing mono-dispersed core–shell structure nanoparticles is reported. The 110 nm SiO₂ cores coated with an yttrium aluminum garnet (Y₃Al₅O₁₂) layer doped with Er³⁺ were synthesized and the influence of the concentration ratio of [urea]/[metal ions] on the final product was investigated. The structure and morphology of samples were characterized by the X-ray powder diffraction, Fourier transform IR spectroscopy and transmission electron microscopy, respectively. The results indicate that a layer of well-crystallized garnet Y₃Al₅O₁₂:Er³⁺ were successfully coated on the silica particles with the thickness of 20 nm. The near infrared and upconversion luminescent spectra of the SiO₂@Y₃Al₅O₁₂:Er³⁺ powders further confirm that a Y₃Al₅O₁₂:Er³⁺ coating layer has formed on the surface of silica spherical particles.     

Kinetics of low-temperature initiation of H<Subscript>2</Subscript>/O<Subscript>2</Subscript>/H<Subscript>2</Subscript>O mixture combustion upon the excitation of molecular vibrations in H<Subscript>2</Subscript>O molecules by laser radiation

The initiation of H₂/O₂/H₂O mixture combustion when asymmetric vibrations in H₂O molecules are excited by a resonant IR laser radiation is considered. It is shown that the vibrational excitation of the molecules gives rise to new efficient channels for the formation of chemically active O and H atoms and OH radicals. As a result, the chain mechanism of combustion in the mixtures is enhanced and, as a consequence, the induction time is cut and the ignition temperature is lowered. Even at a minor radiant energy flux delivered to the gas (E_in≈2.5 J/cm²), the ignition temperature of the stoichiometric H₂/O₂ mixture containing only 5% of H₂O may become as low as 300 K.     

A high efficient antireflective down-conversion Y<Subscript>2</Subscript>O<Subscript>3</Subscript>:Bi<Superscript>3+</Superscript>, Yb<Superscript>3+</Superscript> thin films

The high efficient antireflective down-conversion Y₂O₃:Bi, Yb films have been prepared successfully on Si(100) substrates by pulsed laser deposition (PLD) method, Upon excitation of ultraviolet photon varying from 300 to 400 nm, near-infrared emission of Yb³⁺ was observed for the film, can be efficiently absorbed by silicon (Si) solar cell. Most interestingly, there is a very low average reflectivity 1.46% for the incident light from 300 to 1100 nm. To the best of our knowledge, this is the lowest reflectance for the down-conversion thin films prepared by cost efficient method. The surface topography of the high efficient antireflective films can be controllably tuned through the substrate template regulation by optimizing process parameters. Besides, the results showed that there is a close relationship between luminescent property and morphology of the film. With the change of the surface morphology, the intensity of Bi³⁺ and Yb³⁺ emission peaks increase first and then decrease. The obtained results demonstrate that this film can enhance the Si solar cell efficiency through light trapping and spectrum shifting.     

Magnetic properties of LiNi<Subscript>0.5</Subscript>Mn<Subscript>0.47</Subscript>Al<Subscript>0.03</Subscript>O<Subscript>2</Subscript> as positive electrode for Li-ion batteries

The layered LiNi_0.5Mn_0.47Al_0.03O₂ was synthesized by wet chemical method and characterized by X-ray diffraction and analysis of magnetic measurements. The powders adopted the α-NaFeO₂ structure. This substitution of Al for Mn promotes the formation of Li(Ni_0.47²⁺Ni_0.03³⁺Mn_0.47⁴⁺Al_0.03³⁺)O₂ structures and induces an increase in the average oxidation state of Ni, thereby leading to the shrinkage of the lattice unit cell. The concentration of antisite defects in which Ni²⁺ occupies the (3a) Li lattice sites in the Wyckoff notation has been estimated from the ferromagnetic Ni²⁺(3a)–Mn⁴⁺(3b) pairing observed below 140 K. The substitution of 3% Al for Mn reduces the amount of antisite defects from 7% to 6.4–6.5%. The analysis of the magnetic properties in the paramagnetic phase in the framework of the Curie–Weiss law agrees well with the combination of Ni²⁺ (S = 1), Ni³⁺ (S = 1/2) and Mn⁴⁺ (S = 3/2) spin-only values. Delithiation has been made by the use of K₂S₂O₈. According to this process, known to be softer than the electrochemical one, the nickel ions in the (3b) sites are converted into Ni⁴⁺ in the high spin configuration, while Ni²⁺(3a)–Mn⁴⁺(3b) ferromagnetic pairs remain, as the Li⁺(3b) ions linked to the Ni²⁺(3a) ions in the antisite defects are not removed. The results show that the antisite defect is surrounded by Mn⁴⁺ ions, implying the nonuniform distribution of the cations in agreement with previous NMR and neutron experiments.     

Effect of the atomic composition of the surface on the electron surface states in topological insulators A<Stack><Subscript>2</Subscript><Superscript>V</Superscript></Stack>B<Stack><Subscript>3</Subscript><Superscript>VI</Superscript></Stack>

The results of the theoretical investigation of the surface electronic structure of A₂^VB₃^VI compounds containing topologically protected surface states are reported. The ideal Bi₂Te₃, Bi₂Se₃, and Sb₂Te₃ surfaces and surfaces with an absent external layer of chalcogen atoms, which were observed experimentally as monolayer terraces, have been considered. It has been shown that the discrepancy between the calculated Fermi level and the value measured in the photoemission experiments can be attributed to the presence of the “dangling bond” states on the surface of the terraces formed by semimetal atoms. The fraction of such terraces on the surface has been estimated.     

Synthesis and electrical properties of new perovskite-like <Emphasis Type="Italic">A</Emphasis>Mn<Subscript>3</Subscript>V<Subscript>4</Subscript>O<Subscript>12</Subscript> (A = Ca,Ce, and Sm) compounds

AMn₃V₄O₁₂ (A = Ca, Ce, and Sm) compounds with a perovskite structure are synthesized at high pressures and temperatures. The crystalline structure of these compounds (space group \(Im\bar 3\)Z = 2) is determined via X-ray analysis. If ions in the A sublattice are changed in the order Ca²⁺–Sm³⁺–Ce³⁺, the valence is redistributed from Ca²⁺Mn₃²⁺V₄⁴⁺O₁₂ to Sm³⁺Mn₃²⁺V₄^3.75+O₁₂, and to Ce³⁺Mn₃²⁺V₄^3.75+O₁₂. The temperature dependences of the electrical resistivity are studied.     

Magnetic properties of Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> surface

The magnetic properties of the magnetite Fe₃O₄(110) surface have been studied by spin resolved Auger electron spectroscopy (SRAES). Experimental spin resolved Auger spectra are presented. The results of calculation of Auger lines polarization carried out on the basis of electronic state density are presented. Problems related to magnetic moments of bivalent (Fe²⁺) and trivalent (Fe³⁺) ions on the Fe₃O₄(110) surface are discussed. It is established that the deposition of a thin bismuth film on the surface results in significant growth of polarization of iron Auger peaks, which is due to additional spin-orbit scattering of electrons by bismuth atoms.     

Accuracy in determination of the temperature and partial pressure of CO<Subscript>2</Subscript> in CO<Subscript>2</Subscript>:N<Subscript>2</Subscript>:H<Subscript>2</Subscript>O:NO<Subscript>2</Subscript> mixtures by multiple-frequency laser probing

We present the results of analysis of the errors introduced by hot-band transitions 11¹0-01¹1, 03¹0-01¹1, 12⁰0-12⁰1 of the CO₂ molecule and the absorption lines of the H₂O and NO₂ molecules in determination of the temperature and partial pressure of CO₂, included in the gas mixture CO₂: N₂:H₂O: NO₂ at atmospheric pressure, by multiple-frequency laser probing using a CO₂ laser tunable over the lines of the 00⁰1-[10⁰0,02⁰0]_I,II ground-state laser transitions. __________ Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 74, No. 6, pp. 810–815, November–December, 2007.     

Luminescence excitation in reactive molecular CO + O<Subscript>2</Subscript> collisions on the surface of Y<Subscript>2</Subscript>O<Subscript>3</Subscript>-Eu

It is shown that the CO + O₂ → CO₂ catalytic reaction on the surface of Y₂O₃-Eu may lead to electronic excitation of Eu³⁺ luminescence centers due to the chemical energy release. The luminescence observed allows one to study the interaction between molecular particles of ultralow (thermal) energies with surface by optical methods.