大孔树脂对红霉素的吸附动力学研究

利用大孔吸附树脂Amberlite XAD16及HZ816对红霉素的吸附动力学实验,研究了温度、初始浓度、溶液pH值及搅拌速度等因素对吸附过程的影响.结果表明,Amberlite XAD16及HZ816对红霉素的吸附速率符合一级吸附动力学方程及颗粒内扩散方程,过程受液膜扩散阻力及颗粒内扩散阻力共同影响.同时,表观吸附速率常数与颗粒内扩散速率常数均随着温度的升高而增大,随着初始浓度的增大而增大,随着溶液pH值增大而增大,随着搅拌速度加快而增大.     

钠型斜发沸石Na+-K+离子交换特性研究(Ⅱ)--过程传质模型及动力学特性研究

利用浅床实验法研究查明了钠型斜发沸石Na -K 离子交换过程以液膜扩散为主的控制机理,依据传质膜理论,推导出液膜控制下的离子交换传质速率模型,并测定了离子交换动力力学曲线和过程传质系数.研究结果表明:钠型斜发沸石Na -K 离子交换速率与溶液流速、温度和溶液的K 浓度成正比,与溶液粘度和沸石粒径成反比,过程总传质系数的模型计算值 与实验值拟和较好.     

L-酪氨酸在732阳离子交换树脂上吸附平衡与动力学研究

研究搅拌槽中732阳离子交换树脂吸附L-酪氨酸的交换平衡和动力学特性,考查了搅拌速度、温度、料液初始pH值、树脂粒径和料液初浓度对离子交换过程的影响.在研究的温度和浓度范围内,该离子交换等温线符合Henry等温式.搅拌速度为350rpm时,可以将外传质阻力忽略.料液初始pH值介于2.5～5.5 时,对交换量影响不大,而料液中Na 的存在会降低树脂的交换量.在忽略外传质阻力的条件下,采用不同粒径计算方法对动力学曲线影响很小.用间歇搅拌槽吸附动力学模型拟合出无外传质阻力条件下、不同初始浓度条件下离子交换的表面扩散系数Ds.结果表明,随着初始浓度的增大,Ds的数量级始终在10-8左右.     

钠型斜发沸石Na~+–K~+离子交换特性研究(II)—过程传质模型及动力学特性研究

利用浅床实验法研究查明了钠型斜发沸石Na~+–K~+离子交换过程以液膜扩散为主的控制机理,依据传质膜理论,推导出液膜控制下的离子交换传质速率模型,并测定了离子交换动力力学曲线和过程传质系数。研究结果表明:钠型斜发沸石Na~+–K~+离子交换速率与溶液流速、温度和溶液的K+浓度成正比,与溶液粘度和沸石粒径成反比,过程总传质系数的模型计算值与实验值拟和较好。     

离子交换法纯化重组类人胶原蛋白Ⅱ的吸附动力学研究

为了确定重组类人胶原蛋白Ⅱ(Recombinant human-like collagen,RHLC Ⅱ)在CM52树脂上的动力学行为,考察温度、初始浓度等因素的影响,分别采用简单线性推动力模型(液膜扩散控制时)和均相扩散模型(颗粒扩散控制时)研究RHLC Ⅱ在不同工艺条件下的反应速率,确定离子交换过程的速率控制步骤,并计算模型参数.结果表明,(1)速率控制机理受转速和料液初始浓度的影响,在转速和料液初始浓度较低时,为液膜扩散控制(Film Diffusion Control,FDC);反之,则为颗粒扩散控制(Particle Diffusion Control,PDC);(2)以简单线性推动力模型拟合液膜扩散控制时的动力学数据,其线性关系良好,模型准确度较高;对于颗粒扩散控制的吸附,则以均相扩散模型拟合,求出有效扩散系数,模型较好地描述了CM52对RHLC Ⅱ的PDC吸附.(3)对于FDC,温度越高,溶液浓度越大,搅拌转速越高,外扩散速度常数越大,吸附越快;对于PDC,温度升高,有效扩散系数增大,吸附加快,料液浓度对有效扩散系数的影响不显著.     

离子交换树脂吸附乙酰丙酸的动力学研究

研究了大孔弱碱性树脂D310对乙酰丙酸的静态吸附动力学特征.采用批式离子交换法,考察了树脂粒径、溶液浓度、搅拌速率、温度对交换过程的影响,并用动边界模型对乙酰丙酸的离子交换过程进行了描述..结果表明,离子交换过程的控制步骤为颗粒扩散控制,搅拌速率和反应温度对交换速率无显著影响,吸附速率随乙酰丙酸初始浓度的增加而升高.交换过程的反应速率常数k0为0.8315,反应级数n为0.5313,表观活化能Ea为9.504kJ/mol,并得到了动力学总方程式.     

粗硼砂的氯化铵溶液浸提动力学

研究了反应温度、溶液浓度、固液比、固体粒径大小和搅拌速度对氯化铵溶液浸提粗硼砂(十水四硼酸钠,Na₂B₄O₇·10H₂O)动力学的影响。结果表明反应速率随反应温度、溶液浓度的增加和固体粒径、固液比的减小而增加,但搅拌速度对溶解速率无显著影响。根据均相和多相动反应力学模型研究了粗硼砂的溶解过程。结果表明溶解速率遵从假一级均相反应模型。粗硼砂在氯化铵溶液中溶解的活化能为82.73 kJ·mol^-1。     

甲烷水合物分解及自保护效应的分子动力学模拟

采用分子动力学(MD)方法, 在温度T = 240, 260, 280和300 K的条件下模拟了Ⅰ型甲烷水合物晶体的分解过程. 研究发现,水合物分解后将在相界面上形成一层“准液膜”,准液膜中水分子的结构性质、空间取向和动力学性质均出现由“似晶”到“似液”的渐变过程. 在水合物分解过程中, 准液膜的存在对水分子和甲烷分子的扩散形成传质阻力. 由于甲烷分子必须穿过准液膜才能进入气相, 准液膜的传质阻力抑制了甲烷分子向气相的扩散过程, 致使水合物的分解速率随之降低, 从而产生自保护效应. 当温度低于水的冰点时, 准液膜中水分子的“似晶”程度较高, 准液膜的传质阻力较大, 自保护效应较明显. 当温度高于水的冰点时, 准液膜中水分子的“似液”程度较高, 准液膜的传质阻力显著下降, 水合物的自保护效应明显减弱.     

HNO3-Al（NO3）3溶液分离包头混合稀土精矿的研究

根据Al3+与F-能形成稳定的络合离子[AlF6]3-,采用HNO3-Al(NO3)3溶液络合浸出包头混合稀土精矿中的氟碳铈矿。热力学分析结果表明:HNO3-Al(NO3)3体系对稀土精矿浸出反应为自发过程。考察了HNO3浓度、Al(NO3)3浓度、液固比、搅拌速度、温度、搅拌时间这些因素对稀土精矿浸出的影响。实验结果表明:在HNO3浓度3 mol·L-1,Al(NO3)3浓度1.5 mol·L-1,液固比30∶1,搅拌速度300 r·min-1,温度100℃,搅拌时间90 min的条件下,稀土精矿中氟碳铈矿的浸出率达到92.18%,氟碳铈矿与独居石基本分离。通过产物层受界面交换和扩散混合控制的新缩小核模型可用来描述浸出过程的动力学,计算推导出了反应的宏观动力学方程。     

多孔聚丙烯支撑液膜中镉的传输研究

研究了以多孔聚丙烯膜为支撑体, PC-88A/CHCl3为膜载体的金属离子 Cd(Ⅱ )支撑液膜传输行为; 考察了料液相 pH值、载体浓度、温度和起始浓度对 Cd(Ⅱ )传输的影响, 并对该体系富集、传输 Cd(Ⅱ )的最佳条件进行了讨论; 从界面化学和扩散传质角度提出了金属离子的传输动力学方程, 采用直线斜率法对 Cd(Ⅱ )在支撑液膜体系中的扩散层厚度(δ a=8.14× 10- 6 m)和膜内扩散系数( d0=5.43× 10- 10 m2/s)进行了测定, 取得满意结果.     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Selective syntheses of 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones via temperature-dependent Rh(II)-carbenoid-mediated 2H-azirine-ring expansion

The Rh(II)-catalyzed reaction of 2-carbonyl-substituted 2H-azirines with ethyl 2-cyano-2-diazoacetate or 2-diazo-3,3,3-trifluoropropionate provides an easy access to 2H-1,3-oxazines and 1H-pyrrol-3(2H)-ones. These compounds can be selectively prepared from the same starting material using temperature as the only varied parameter. The 2-azabuta-1,3-diene intermediate, a common precursor for both heterocyclic products, isomerizes into 2H-1,3-oxazine under kinetic control, while 1H-pyrrol-3(2H)-one is the sole product of the reaction at elevated temperatures. According to DFT-calculations a one-atom oxazine ring contraction involving ring-opening to a 2-azabuta-1,3-diene intermediate, followed by a 1,5- and 1,2-prototropic shift leads to the consecutive formation of imidoylketene and azomethine ylide, which then further undergo cyclization to the pyrrole derivative.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.