种子乳液聚合方法制备聚苯乙烯—聚硅氧烷核壳粒子

采用种子乳液聚合的方法，制备以聚苯乙烯为壳、聚有机硅氧烷为核的弹性粒子、探讨了加料和引发方式对粒子的结构及形貌的影响，并对苯乙烯种子乳液聚合的机理进行了切步的讨论。     

核/壳乳液聚合工艺中乳化剂的定量研究

以十二烷基硫酸钠(SDS)为乳化剂,采用多步种子乳液聚合方法制备了核/壳结构乳液,研究了乳化剂加入量以及加料速率对核壳乳液聚合的影响,并推导了核及壳乳液聚合阶段所需乳化剂量的计算公式.研究表明,当种子、核、壳乳液聚合阶段单体量分别为12g、50g和50g,种子乳液聚合阶段加入的乳化剂量为0.44g时,控制核、壳乳液聚合阶段乳化剂的加入量分别在0.64～2.07g及0.04～2.12g之间,且预乳化单体的滴加速度低于2.3g/min时,可以防止二次成核及新乳胶粒子的形成,制得粒径分布窄、核/壳结构明显的乳胶粒子.利用透射电镜(TEM)对所制备的核壳结构乳胶粒子的结构形态进行了验证,试验结果与理论预测结果一致.     

室温交联型硅丙微胶乳的合成研究Ⅱ.改性微胶乳的粒径控制及其微观形态表征

采用种子微乳液聚合法和单体预乳化法分别合成了室温交联型有机硅改性聚丙烯酸酯微胶乳，研究了硅烷单体的添加和氧化反应对改性微胶乳粒子大小及分布的影响．结果表明：采用种子微乳液聚合法得到的硅丙微胶乳粒子大小与硅烷单体的种类．用量和添加顺序无关，平均粒径约为40-60nm．TEM照片显示出，采用种子微乳液聚合法合成的硅丙微胶乳舡子由于内部存在交联结构而导致表面形状不规则，有“乳突”现象；而采用预乳化法合成的硅丙微胶乳粒径粗大，呈规则的球形，氧化后柱径从100nm以上减小到80nm左右，粒子表面出现“绒毛”现象，这是由于硅烷组分的水解反应受到抑制而使粒子内部的交联密度降低的缘故．     

单分散亚微米级磁性微球的合成

以磁性氧化铁胶体粒子为种子粒子，采用吸附－溶胀法，进行苯乙烯－丙烯酸－二乙烯基苯的乳液聚合，制备亚微米级磁性高分了微球。研究了分散介质、丙烯酸、种子粒子、苯乙烯和ＰＨ调节剂等因素对聚合行为和磁性微球的影响，成功地合成了平均粒径为０．１３和０．２７μｍ、单分散性很好的磁性微球。     

种子乳液聚合的研究进展

种子乳液聚合法因具有乳液稳定性更好、粒径分布窄、易控制等优点,在乳胶粒子设计及制备各种功能性胶乳方面具有重要作用,是制备高固含量乳液及具有核壳结构乳液的最常见最简便的方法.本文综述了近年来种子乳液的聚合工艺、聚合机理, 包括接枝机理、互穿聚合物网络机理、聚合物沉积机理、种子表面聚合机理和离子键合机理等,以及种子乳液聚合在乳胶粒子设计方面的应用研究进展,并讨论了影响种子乳液聚合的各种因素.     

聚合物纳米粒子乳液的制备及性能研究——添加组分对乳胶粒子形态及胶膜吸水率的影响

本文采用种子微乳液聚合方法,经后期氨化反应,合成了聚丙烯酸酯纳米粒子乳液,讨论了乳化剂、缓冲剂和水溶性丙烯酸单体等添加组分对乳粒子形态和胶膜吸水率的影响,并探讨了微乳液聚合的反应机理。     

室温交联型硅丙微胶乳的合成研究II.改性微胶乳的粒径控制及其微观形态表征

采用种子微乳液聚合法和单体预乳化法分别合成了室温交联型有机硅改性聚丙烯酸酯微胶乳,研究了硅烷单体的添加和氨化反应对改性微胶乳粒子大小及分布的影响。结果表明:采用种子微乳液聚合法得到的硅丙微胶乳粒子大小与硅烷单体的种类、用量和添加顺序无关,平均粒径约为40~60nm。TEM照片显示出,采用种子微乳液聚合法合成的硅丙微胶乳粒子由于内部存在交联结构而导致表面形状不规则,有“乳突”现象;而采用预乳化法合成的硅丙微胶乳粒径粗大,呈规则的球形,氨化后粒径从100nm以上减小到80nm左右,粒子表面出现“绒毛”现象,这是由于硅烷组分的水解反应受到抑制而使粒子内部的交联密度降低的缘故。     

核壳型聚丙烯酸酯乳胶粒子及其乳液的研究进展

综述了目前制备核壳型聚丙烯酸酯乳胶粒子的常用方法,如种子乳液聚合法、无皂乳液聚合法、反相乳液聚合法、细乳液聚合法以及种子分散聚合法;分析了聚合工艺、单体种类、温度、乳化剂和引发剂种类及用量等因素对聚丙烯酸酯核壳乳液合成及性能的影响;并对聚丙烯酸酯核壳乳液的研究现状进行了归纳;最后,展望了聚丙烯酸酯核壳乳液的发展方向。     

聚硅氧烷/甲基丙烯酸甲酯核壳结构复合粒子的制备

聚硅氧烷/甲基丙烯酸甲酯核壳结构复合粒子的制备;种子乳液聚合;核壳结构     

醋酸乙烯酯种子乳液聚合动力学研究

用装有红外跟踪器和计算机记录监控系统的膨胀计进行了醋酸乙烯酯的种子乳液聚合。聚合直接从乳液聚合的阶段Ⅱ开始，避开了复杂的成核阶段和成核阶段粒度变化对动力学参数的影响。在引发剂浓度５．０３０×１０＾－５￣１．００２×１０＾－３ｍｏｌ／Ｌ范围内，依据转化率随时间的变化关系，求出了准稳态聚合速率、自由基进入乳胶粒子的速率、自由基从乳胶粒子解吸的速率和ｋｐｎ＾－。结果表明：聚合速率、自由基进入乳胶粒子的速     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。