CuNi/β-环糊精/还原氧化石墨烯修饰电极电化学检测多巴胺

建立了一种循环伏安法制备CuNi/β-环糊精/还原氧化石墨烯修饰玻碳电极(CuNi/β-CD/ERGO/GCE)的方法。通过多巴胺在该修饰电极上的电化学行为发现,该电化学传感器实现了快速、灵敏的测定多巴胺。该传感器用差分脉冲伏安法(DPV)测定多巴胺时,其电化学响应电流与多巴胺浓度在0.01~20μmol/L之间呈线性关系,检测限为8 nmol/L。该传感器用于尿液样品中的多巴胺检测,回收率在95.6%~107.2%之间。     

石墨烯-壳聚糖/金纳米粒子修饰电极同时测定亚硫酸根和亚硝酸根

采用滴涂法得到了石墨烯(GR)-壳聚糖(CS)修饰的玻碳电极(GCE),再采用电沉积的方法将HAuCl4直接还原成金纳米粒子,沉积在GR-CS表面,制得了GR-CS/AuNPs GCE修饰电极。采用透射电子显微镜(TEM)分别对制备的GR和构建的修饰电极GR-CS/AuNPs GCE进行了形貌表征。用循环伏安法研究了SO32-和NO2-在GR-CS/AuNPs GCE上的电化学行为。结果表明,此修饰电极对SO32-和NO2-均有较好的电催化活性作用,并且能实现对两种物质的同时测定,SO32-和NO2-在该修饰电极上的线性范围分别为5～410μmol/L和1～380μmol/L,检出限(S/N=3)分别为1.0和0.25μmol/L。GR-CS/AuNPs GCE具有很好的稳定性、重现性和灵敏度。此电极用于实际水样的SO32-和NO2-的含量测定,回收率为97.2%～102.6%,结果令人满意。     

聚L-半胱氨酸/还原氧化石墨烯/Nafion修饰玻碳电极对芦丁的电化学传感行为研究

本文采用滴涂法制备了还原氧化石墨烯/Nafion溶液修饰玻碳电极(rGO/Nafion/GCE),用电化学聚合法将L-半胱氨酸(L-Cys)聚合在rGO/Nafion/GCE表面,得到Poly-L-Cys/rGO/Nafion/GCE。采用伏安法研究了芦丁在该修饰电极上的电化学行为及其影响因素。结果表明,L-Cys的电聚合圈数对修饰电极的电化学性能具有一定的影响。在最优条件下,芦丁的峰电流与其浓度在2.0×10~(-8)~1.0×10~(-5) mol/L内呈现好的线性关系,检出限(S/N=3)为1.0×10~(-8) mol/L。     

聚L-白氨酸-碳纳米管修饰电极同时检测对苯二酚和邻苯二酚

用Nafion将单壁碳纳米管(SWCNT)固定到玻碳电极(GCE)上,再利用电化学聚合方法将L-白氨酸(L-LEU)聚合到SWCNT/GCE上,制备得到poly L-LEU/SWCNT/GCE修饰电极。采用循环伏安法(CV)、差分脉冲伏安法(DPV)和电化学交流阻抗法(EIS)研究了对苯二酚(HQ)、邻苯二酚(CC)共存时,二者在修饰电极上的电化学行为。结果表明:此修饰电极对HQ和CC有很好的电催化和分离作用。二者在修饰电极上的氧化还原峰电流与GCE相比显著增强,HQ和CC的氧化峰电位差和还原峰电位差分别为124 mV和131 mV。HQ和CC的检测线性范围分别为2.0×10-7~1.0×10-4、5.0×10-7~1.0×10-4mol/L。检出限分别为8.0×10-8、1.0×10-7mol/L。制备的修饰电极重现性、稳定性良好。在模拟废水中采用该修饰电极对HQ和CC进行检测,结果满意。     

基于聚对氨基苯磺酸、功能化石墨烯和纳米金修饰电极的构筑及用于双酚A的测定

通过电聚合方法制备聚对氨基苯磺酸修饰的玻碳电极（GCE/pABSA）,然后把带有正电荷的超支化聚乙烯亚胺功能化还原氧化石墨烯（BPEIGr）和带有负电荷的金纳米粒子（AuNPs）依次修饰到电极上,制得GCE/pABSA/BPEIGr/AuNPs修饰电极。研究了双酚A在GCE/pABSA/BPEIGr/AuNPs修饰电极上的电化学行为。结果表明,所制备的修饰电极对双酚A有良好的电催化效果,在pH 7.0的PBS溶液中进行循环伏安扫描,双酚A在0.2～0.8 V范围内出现1个不可逆的氧化还原峰。采用差分脉冲伏安法（DPV）对双酚A进行了检测,在优化的条件下,双酚A的浓度在0.05～10μmol/L范围内与氧化峰电流呈线性关系,检出限为0.02μmol/L(3σ)。将基于此修饰电极的传感器用于浑河水和自来水中双酚A含量的测定,加标回收率在97.0%～105.0%之间。     

L-半胱氨酸/普鲁士蓝复合修饰玻碳电极的制备及电化学性能

通过电聚合方法和脉冲沉积技术将普鲁士蓝(PB)与L-半胱氨酸(L-Cys)修饰在玻碳电极(GCE)表面,制得复合膜化学修饰电极(L-Cys/PB/GCE/CME),利用循环伏安法和计时安培法研究了对苯二酚在L-Cys/PB/GCE/CME上的电化学特征。结果表明,在0.1 mol/L PBS(pH 7.0)缓冲溶液中,L-Cys/PB/GCE/CME对对苯二酚的电化学氧化具有明显的催化作用,氧化峰电流相对于在裸玻碳电极上增加了5倍。在最佳实验条件下,对苯二酚浓度在0.18~120μmol/L范围内,修饰电极的电流响应与对苯二酚浓度呈线性关系,其相关系数为0.9962,检出限(S/N=3)为0.065μmol/L。本研究制备的对苯二酚传感器具有较好的重复性、重现性、选择性与稳定性,用于实际水样中对苯二酚的测定,结果满意。     

碳纳米管修饰电极检测特丁基对苯二酚

利用碳纳米管修饰玻碳电极(MWCNTs/GCE),对特丁基对苯二酚(TBHQ)进行了检测,采用循环伏安法(CV)和差分脉冲伏安法(DPV)考察了TBHQ在裸电极和修饰电极上的电化学行为。M WCNTs/GCE对TBHQ的氧化具有较好的电催化活性,在修饰电极上的氧化还原峰电位差从261 m V减小到30 m V。在0.10 mol/L磷酸盐缓冲溶液(p H 7.0)中,扫速为50 m V/s时,此修饰电极的DPV响应与TBHQ浓度在2~250μmol/L范围内呈线性关系,检出限为0.1μmol/L(S/N=3)。此修饰电极可应用于食用油中TBHQ的测定,回收率为92.0%~104.0%。     

巯基β-环糊精/还原氧化石墨烯/金纳米粒子复合膜修饰电极间接检测3,3′,4,4′-四氯联苯

本文采用巯基β-环糊精(β-CD-SH)/还原氧化石墨烯(rGO)/金纳米粒子(AuNPs)复合膜对玻碳电极(GCE)进行修饰,构建了以K_3[Fe(CN)_6]为探针,间接检测3,3′,4,4′-四氯联苯(PCB77)的电化学传感器。通过循环伏安法(CV)与差分脉冲伏安法(DPV)对该传感器的电化学性质及电极反应机理进行了研究,并优化了电极的制备及其检测PCB77的条件。在最佳条件下,PCB77浓度在0.5～10.0μmol/L范围与峰电流变化值ΔI_p呈良好的线性关系,相关系数R=0.9954,检出限为0.081μmol/L。对实际样品的检测,加标回收率在91.2%～106.2%之间。     

原位氮掺杂石墨烯修饰电极同时检测苯二酚3种异构体

利用多巴胺的聚合及还原特性,制备聚多巴胺包覆还原氧化石墨烯,在氮气保护下煅烧,制得氮原位掺杂石墨烯(C/N-Graphene)。应用扫描电镜(SEM)、透射电镜(TEM)、傅里叶变换红外(FT-IR)光谱表征该复合物的形貌和结构。应用滴涂及Nafion膜固定法制备C/N-Graphene修饰玻碳电极(C/N-Graphene/GCE)。该修饰电极对苯二酚3种异构体的氧化反应表现出优异的电催化性能和选择性,差分脉冲伏安法(DPV)峰电流与对苯二酚(HQ)、邻苯二酚(CC)、间苯二酚(RC)的浓度呈良好的线性关系,其线性范围分别为0.5~1 000μmol/L、0.5~460μmol/L和0.1~580μmol/L,检出限分别为0.251μmol/L、0.144μmol/L和0.072μmol/L。该方法应用于药厂废水和江水检测,3种苯二酚异构体回收率为97.0%~103.0%,相对标准偏差(RSD)小于5%(n=5),结果表明C/N-Graphene/GCE修饰电极适用于污染水样的快速检测。     

电化学还原氧化石墨烯/纳米金-壳聚糖复合膜修饰玻碳电极对尿酸的灵敏测定

将氧化石墨烯(GO)在玻碳电极(GCE)表面进行直接电化学还原,再组装上纳米金-壳聚糖(AuNPCS)聚阳离子,形成了电化学还原氧化石墨烯/纳米金-壳聚糖(ERGO/AuNP-CS)复合膜修饰的玻碳电极。采用扫描电子显微镜(SEM)表征了不同修饰膜表面的形貌,探讨了其对尿酸(UA)分子的差分脉冲伏安(DPV)行为,发现ERGO/AuNP-CS复合膜对UA分子表现出显著的电催化氧化活性。在0.10 mol/L磷酸盐缓冲溶液(pH=6.5)中,扫速为100 mV/s时,此复合膜修饰电极的DPV响应与UA的浓度在0.05~110μmol/L范围内呈性关系,检测限为12.4 nmol/L(S/N=3)。此修饰电极具有良好的选择性、重现性和稳定性,可应用于人体血清和尿液样品中UA的测定,回收率达到93.8%~104.1%。结果与分光光度法和尿酸酶试剂盒法相符。     

Solvent extraction separation of In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/ with sulphoxides

Solvent extraction studies have been made on some metals: In/III/-Tl/III/ and Hg/II/-Cd/II/-Co/II/, from ammonium thiocyanate solutions by dialkyl sulphoxides. Separation of these metals from one another can be achieved by suitable choice of the extracted conditions. The nature of the extractable metal species has been elucidated.     

Synthesis of chlorobis/β-diketonato/oxotechnetium/V/ and tris/β-diketonato/technetium/III/ complexes

Chlorobis/-diketonato/ oxotechnetium/V/ complexes [TcOCl/-dik/₂, -diketone=acetylacetone, benzoylacetone and dibenzoylmethane] were newly synthesized using macroamount of⁹⁹Tc. These complexes were further separated into geometrical isomers. Furthermore, an improvement of the yields for the syntheses of tris/-dike-tonato/technetium/III/ complexes [Tc/-dik/₃, -diketone=acetylacetone, benzoylacetone and 2-thenoyltrifluoroacetone] was examined using Tc/III/-thiourea complexes as a starting material.     

Simultaneous propane dehydrogenation andco2hydrogenation overCrOx/SiO2catalyst

Summary Single reverse water-gas shift (RWGS) and dehydrogenation of propane with CO₂(DH-CO₂) reactions in the presence and absence of the CrO_x/SiO₂ catalyst have been studied between 673 and 873 K. It was found that the CrO_x/SiO₂ catalyst is active both in the dehydrogenation of propane and in the RWGS reactions. The obtained results suggest that the dehydrogenation of propane to propene in the presence of CO₂on CrO_x/SiO₂can be facilitated by the RWGS reaction.</o:p>     

Direct synthesis of dimethyl carbonate ?from CH3OH AND CO2 by H3PW12O40/CexTi1-xO2 catalyst

Summary Ce_xTi_1-xO₂ and H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts were prepared using a sol-gel method, and applied to the direct synthesis of dimethyl carbonate from methanol and carbon dioxide. H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ showed a better catalytic performance than the corresponding Ce_xTi_1-xO₂, due to the bifunctional catalysis of Br?nsted acid sites (provided by H₃PW₁₂O₄₀) and base sites (provided by Ce_xTi_1-xO₂). H₃PW₁₂O₄₀/Ce_0.1Ti_0.9O₂ showed the highest catalytic performance among the H₃PW₁₂O₄₀/Ce_xTi_1-xO₂ catalysts.     

Crystal structure of Na3PO4 · 12H2O

The crystal structure of trisodium monophosphate hemihydrate was determined. The space group is $\text{C2}\text{c}$ and a unit cell contains eight formula units. The unit cell dimensions of $\text{Na}{}_3\text{PO}{}_4\text{·}\text{1}\text{2}\text{H}{}_2\text{O}$ are a = 9.631(3), b = 5.416(2), c = 16.938(8) Å, β = 102.60(5)°. The final R value is 0.027 for a set of 1430 independent reflections. This atomic arrangement is mainly a three-dimensional network of distorted NaO₆ octahedra. The hydrogen bonding scheme is given.     

LixNi0.8-yCo0.2ZnyOp的合成及电化学性能研究

A series of single-phase Li_xNi_0.8-yCo_0.2Zn_yO_p(0.96 ≤x≤ 1.10， 0 ≤y≤ 0.05， 2 ≤p≤ 2(1+y) ) (different in the y values) were synthesized by a two-step solid state reaction method， in which LiOH·H₂O， Zn-doped spherical Ni(OH)₂ and Co₂O₃ were used as the precursors. The ICP-AES analyses proved that the Zn-doped compounds synthesized had the nonstoichiometric form. The results of the XRD， SEM identified that the uniform particles of the as-prepared materials having a good layered structure were fine， narrowly distributed and well crystallized. The electrochemical performance test was carried out and the results showed that the as-prepared Zn-doped materials had not only a high capacity， but also a better cycling stability characterization than the un-doped one. The Li_1.06Ni_0.75Co_0.22Zn_0.03O_2.03 material has an initial reversible capacity as high as 160.5mAh·g^-1; and a first discharge efficiency 89.2%， and exhibits satisfactory cyclic stability with 90% retainable capacity after 50 cycles.     

An investigation of the promotional effect of propylene or propane traces on the activity of sulfatedPt/g-Al2O3andPt-Sn/g-Al2O3inCH4combustion

Summary A strong promoting effect of the presence of C₃H₈or C₃H₆was determined for the combustion of CH₄in excess oxygen, over pre-sulfated 1%Pt/g-Al₂O₃and pre-sulfated 1%Pt-2%Sn/g-Al₂O₃catalysts.</o:p>     

Synthesis and characterization of Ti1−2xNbxNixO2−x/2 solid solutions

Doped-rutile has been traditionally used in ceramic pigments for its intense optical properties. In this paper, we compare the classical ceramic synthesis of Ti_1−2xNb_xNi_xO_2−x/2 system with the sol-gel methodology, which allows a reduction of the anatase-rutile transformation temperature. The composition was optimised in order to obtain a unique rutile phase with the minimum amount of pollutant Ni(II) and enhanced chromatic coordinates. Incorporation of the doping ions in the rutile structure was corroborated by XRD and Rietveld refinements. The species responsible for the colour mechanism were studied by different techniques. UV-VIS spectroscopy showed the characteristic features of Ni²⁺ ions, whose existence was corroborated by EPR and magnetic measurements. From these results, (Ni,Nb)doped-TiO₂ powder samples can be now shaped as thin films, monoliths, etc. by using sol-gel methodology without modifying their properties. This study introduces new possibilities of coloured TiO₂-based solid solutions in new combined advanced applications (colouring agent and photocatalyst, etc.).     

Visible light-sensitive yellow TiO2−xNx and Fe-N co-doped Ti1−yFeyO2−xNx anatase photocatalysts

Nitrogen substituted yellow colored anatase TiO_2−xN_x and Fe-N co-doped Ti_1−yFe_yO_2−xN_x have been easily synthesized by novel hydrazine method. White anatase TiO_2−δ and N/Fe-N-doped samples are semiconducting and the presence of ESR signals at g ∼1.994-2.0025 supports the oxygen vacancy and g∼4.3 indicates Fe³⁺ in the lattice. TiO_2−xN_x has higher conductivity than TiO_2−x and Fe/Fe-N-doped anatase and the UV absorption edge of white TiO_2−x extends in the visible region in N, Fe and Fe-N co-doped TiO₂, which show, respectively, two band gaps at ∼3.25/2.63, ∼3.31/2.44 and 2.8/2.44 eV. An activation energy of ∼1.8 eV is observed in Arrhenius log resistivity vs. 1/T plots for all samples. All TiO₂ and Fe-doped TiO₂ show low 2-propanol photodegradation activity but have significant NO photodestruction capability, both in UV and visible regions, while standard Degussa P-25 is incapable in destroying NO in the visible region The mid-gap levels that these N and Fe-N-doped TiO₂ consist may cause this discrepancy in their photocatalytic activities.     

LixZryOz三元化合物的制备及表征

采用高温固相法制备了4种高纯度晶相组成的LixZryOz三元化合物,研究了焙烧温度、时间、反应物的种类和初始反应物物质的量比对产物组成的影响,进一步用XRD、SEM及BET分析方法对产物的晶相结构、表面形貌及比表面积进行了表征.实验结果表明,Li2CO3与ZrO2在适当条件下可以合成得到单斜相Li3ZrO3;以LiOH替代Li2CO3,在适当条件下可以分别合成得到四方相Li2ZrO3和三斜/单斜相Li6Zr2O7;进一步以Zr(NO3)4·5H2O代替Zr02,可将单斜相Li6Zr2O7的制备时间由96 h缩短至24 h.SEM照片显示产物硬团聚明显,粒径分布在1～10μm间,BET分析表明样品比表面积处于1.0～9.0 m2·g-1间分布,反应过程中锂的过量以及长时间高温焙烧是引起产物粒径长大和产生硬团聚的主要原因.