生物质三组分热裂解行为的对比研究

在热天平上对比研究了生物质中的纤维素、半纤维素和木质素三种主要组分的热失重规律。结果表明，作为半纤维素模型化合物的木聚糖热稳定性差，在217℃～390℃发生明显分解；纤维素热裂解起始温度最高，且主要失重发生在较窄温度区域，固体残留物仅为6.5%；木质素表现出较宽的失重温度区域，最终固体残留物高达42%。在红外辐射机理试验台上对比研究了三组分热裂解产物随温度的变化规律。三组分热裂解生物油产量随温度变化先升后降。纤维素生物油产量在峰值上最高，但纤维素生物油热稳定性差，高温时挥发分的二次分解最明显；木聚糖和木质素生物油产量较低，表现出较好的热稳定性。三组分热裂解焦炭产量随温度升高而降低，最终纤维素热裂解焦炭产量为1.5%，而木聚糖和木质素分别为22%和26%。三组分热裂解气体产物随温度升高而增长，但在气体组成分布上因三组分的结构上的差异而不同。     

木质素二聚体模型化合物热解机理的量子化学研究

β-O-4连接是木质素主体结构单元之间的主要联结方式。采用密度泛函理论方法B3LYP,在6-31G (d, p)基组水平上,对β-O-4型木质素二聚体模型化合物(1-愈创木基-2-(2-甲氧基苯氧基)-1,3丙二醇)的热解反应机理进行了研究。提出了三种热解反应途径:C_β-O键均裂的后续反应、C_α-C_β键均裂的后续反应以及协同反应。对各种反应的反应物、产物、中间体和过渡态的结构进行了能量梯度全优化,计算了各热解反应途径的标准动力学参数。分析了各种主要热解产物的形成演化机理以及热解过程中温度对热解机理的影响。计算结果表明,C_β-O键的均裂反应和协同反应路径(1)和(3)是木质素二聚体热解过程中主要的反应路径,而C_α-C_β键的均裂反应和协同反应路径(2)和(5)是主要的竞争反应路径;热解的主要产物是酚类化合物如愈创木酚、1-愈创木基-3-羟基丙酮、3-愈创木基-3-羟基丙醛、愈创木基甲醛和乙烯等。在热解低温阶段协同反应是热解过程中的主要反应形式,而在高温阶段自由基均裂反应是热解过程的主要反应形式。     

废轮胎热解石脑油馏分的组成分析

研究了废轮胎在回转窑中试反应器中进行中温段(450 ℃～650 ℃)热解所得产物油中石脑油馏分(i.b.p.～200 ℃)的品质。对原始热解油进行实沸点蒸馏,石脑油馏分的收率随热解温度的升高而明显增加,在600 ℃取得最大值40.48%,之后又有所下降。采用GC和GC-MS对石脑油馏分的组成进行了分析。结果表明,热解石脑油具有很强的芳香性,而且芳烃含量随热解温度的升高而持续增加,热解温度在550 ℃以上的石脑油中的芳香烃含量超过80%。轻质单环芳烃苯、甲苯、乙苯和二甲苯等为其中的主要芳烃。热解石脑油中的脂肪烃多为不饱和烃。     

毛竹酶解/温和酸水解木质素的快速热解研究

采用热裂解-气相色谱/质谱仪联用技术,研究毛竹酶解/温和酸水解木质素(简称EMAL)的热解特性和热解产物的分布与形成规律.以温度为重要因素,研究其对木质素快速热裂解产物的影响,并通过主要的热解产物推断热解反应途径.研究结果表明,EMAL的热解产物主要是2,3-二氢苯并呋喃、酚类、脂类和少量乙酸.热解温度对热解产物组分的相对含量有显著影响,250~400 ℃时,产物主要是2,3-二氢苯并呋喃,320 ℃时其相对含量最高,达到66.26%;400~800 ℃时,热解产物主要是酚类,600 ℃时其相对含量最高,达到62.58%;800 ℃时出现了少量的乙酸.     

抽提物对生物质热裂解机理的影响研究

利用惰性溶剂从生物质中提取得到相应抽提物,在热重红外联用仪上研究了抽提物的热裂解行为,并探讨了其对生物质热裂解的影响。结果表明,因不同种类生物质中木质素结构单元中紫丁香基和愈创木基数量不同,从而导致抽提物成分存在差异,相应的热裂解产物分布也不一致。水曲柳抽提物因含有较多的酚类物质而在热解高温段生成了甲醇和甲烷。相比于原样,抽提残渣反应活化能增加,且主要产物析出时间提前,同时酸类物质和直链烷烃析出量减少,而水、CO2、CO和醛类物质的产量则有所增加。     

热解温度对酸沉淀工业木质素快速热解液体产物的影响

利用快速热解和气质联用技术,研究了酸沉淀工业木质素在400℃～700℃下快速热解液体产物的主要组分及其含量的变化。酸沉淀工业木质素快速热解液体产物中主要包括,与木质素的三种苯丙烷结构单元结构相似的苯酚、愈疮木酚和2,6 二甲氧基苯酚等酚类化合物,以及它们的甲基、乙基或丙基的单取代或多取代衍生物。在400℃～600℃,热解液体产物的组分及其相对含量的变化不显著;而在600℃～700℃,芳环上含甲氧基的酚类物质的相对含量急剧减少甚至消失,而苯酚的相对含量却急剧增加,达到27.81％,比400℃的增加了近2.5倍,同时芳烃化合物的相对含量增加,并出现苯丙呋喃、茚和萘等芳环化合物。     

生物质主要组分低温热解研究

利用热重分析仪和裂解气质联用仪进行生物质主要组分低温热解特性研究。热重实验结果表明,生物质主要组分的热稳定性为：纤维素>木质素>半纤维素。半纤维素主要热解温度在210℃～320℃,而纤维素和木质素的主要热解温度分别在310℃～390℃和200℃～550℃。裂解气质联用实验考察不同温度对生物质主要组分低温热解产物的影响。半纤维素热解产物主要有乙酸、1-羟基-丙酮和1-羟基-2-丁酮,纤维素热解产物主要包括左旋葡聚糖和脱水纤维二糖,而木质素热解产物主要是邻甲氧基苯酚。     

油页岩热解挥发分产物二次反应对油气收率与组成的影响

采用两段反应器对油页岩热解释放的一次挥发分产物进行不同热态条件下的二次反应特性研究,考察第二段温度、气氛与停留时间对油气收率及品质的影响。研究结果表明,转化温度对油气产率的影响最明显,在优化第一段热解反应条件的基础上,当反应器第二段温度由600℃提高到650℃时,油页岩热解油产率下降15%(质量分数,下同),气体产率增加约20%。与氮气气氛相比,水蒸气作为第二段反应气氛能够提高液体油品收率约5%,并且热解油主要集中在馏程350℃的汽柴油馏分。结合GC-MS分析表明,停留时间0-3 s二次反应主要为裂解过程,水蒸气能够提高油品中芳烃含量,同时抑制芳烃缩聚;3-5 s二次反应主要为缩聚过程,焦炭生成量增加,汽柴油馏分收率保持稳定,VGO馏分油收率下降约30%。     

木质素二聚体模型物裂解历程的理论研究

木质素作为生物质的主要成分之一, 是生物油的重要组分, 在工业生产中有着重要的应用. 生物质高温裂解液化制备生物油的过程伴随着木质素的裂解, 因此研究木质素高温裂解历程, 对生物油的制备有很大的帮助. 利用密度泛函方法对木质素在高温条件下的裂解历程进行理论研究, 并通过对各步反应的热力学焓变计算, 确定了初次裂解的路径为Cα—Cβ和β-O-4热裂解路径. 根据进一步的研究预测了裂解反应的主要产物.     

废轮胎回转窑中试热解油的理化性质

研究了回转窑中试反应器中废轮胎热解所得液体产物油的品质。热解反应在中温段(450℃～650℃)进行，油产率在500℃有最大值45.1%，此后随温度升高而呈下降趋势。对热解油的品质进行了考察，获取了热解油的完整实沸点蒸馏曲线。结果表明，热解油品质较轻，200℃以下轻馏分总量高达33%～40%，而且热解温度的升高也有助于增加轻馏分含量。对各馏分进一步的FT-IR分析显示，较高热解温度下热解油具有较强的芳香性，并可从谱图中识别出苯、萘及其烷基衍生物等芳香类物质。600 ℃和500 ℃热解油低馏分FT-IR分析结果体现了热解芳烃类物质生成的Diels-Alder反应途径。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Summary of development of the theory of stability of colloids and thin films

In this review, the research of the author in the field of colloidal systems is summarized. The factors influencing colloidal stability are systematized and analyzed. Examples are presented to illustrate the practical utilization of the theory of stability of colloids and thin films.This review was prepared on the basis of the works of the author, which were awarded the State Premium for 1991 in the field of science and technology, chemistry section.Institute of Physical Chemistry, Russian Academy of Sciences, 117915 Moscow. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 8, pp. 1708–1717, August, 1992.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Thermodynamics of the formation of oxosulfides of rare-earth elements

The enthalpies of solution of several oxosulfides of rare-earth elements and the high-temperature enthalpies of oxosulfides and oxosulfates of lanthanum and yttrium were measured using solution calorimetry and high-temperature microcalorimetry techniques. Standard enthalpies of formation and some thermodynamic properties of oxosulfides and oxosulfates were calculated. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 2 pp. 294–297, February, 1997.     

探究“铁的锈蚀条件”实验创新设计

设计了铁的锈蚀实验,说明了铁钉的处理方法,增加了温度、酸、碱的影响条件,实现了铁跟蒸馏水及空气中氧气快速反应而生锈,使实验在5 min左右就能够得到准确的结果。