均匀流直通穿孔消声器的声学特性分析

将数值模态匹配法(NMM)扩展应用于计算有均匀流存在时直通穿孔管抗性和阻性消声器的声学特性,编写了相应的计算程序。对于圆形同轴穿孔管抗性和阻性消声器,应用数值模态匹配法计算得到的传递损失结果与实验测量结果吻合良好,从而验证了计算方法和计算程序的正确性。进而应用数值模态匹配法研究了运流效应和穿孔阻抗以及穿孔管偏移对穿孔管抗性和阻性消声器传递损失的影响。研究结果表明,马赫数越高,穿孔管抗性消声器在中高频的消声量越高,阻性消声器在整体频段内的消声性能越差;低马赫数时运流效应对穿孔管抗性消声器的影响可以忽略,马赫数较高时运流效应和穿孔阻抗的影响比较明显;对于穿孔管阻性消声器,穿孔阻抗对消声器声学特性的影响比运流效应的影响小,但是与真实值的差别不可忽略;穿孔管偏移对消声器声学特性的影响与频率和消声器结构均相关。      

均匀流直通穿孔消声器的声学特性分析

将数值模态匹配法(NMM)扩展应用于计算有均匀流存在时直通穿孔管抗性和阻性消声器的声学特性,编写了相应的计算程序。对于圆形同轴穿孔管抗性和阻性消声器,应用数值模态匹配法计算得到的传递损失结果与实验测量结果吻合良好,从而验证了计算方法和计算程序的正确性。进而应用数值模态匹配法研究了运流效应和穿孔阻抗以及穿孔管偏移对穿孔管抗性和阻性消声器传递损失的影响。研究结果表明,马赫数越高,穿孔管抗性消声器在中高频的消声量越高,阻性消声器在整体频段内的消声性能越差;低马赫数时运流效应对穿孔管抗性消声器的影响可以忽略,马赫数较高时运流效应和穿孔阻抗的影响比较明显;对于穿孔管阻性消声器,穿孔阻抗对消声器声学特性的影响比运流效应的影响小,但是与真实值的差别不可忽略;穿孔管偏移对消声器声学特性的影响与频率和消声器结构均相关。     

插管结构对膨胀腔消声器声学性能的影响

将数值模态匹配法(NMM)拓展应用于计算和分析外插管膨胀腔消声器的声学性能,推导了相应的理论公式并编写了计算程序。使用二维有限元法提取横向波数和本征向量,应用模态匹配法计算消声器的传递损失。使用数值模态匹配法和三维有限元法(FEM)研究了插管长度和进出口位置对带有外插进出口管椭圆形非同轴膨胀腔消声器声学性能的影响,两种方法计算结果吻合良好,从而验证了本文数值模态匹配法的正确性。研究结果表明,设置特定的插管长度和进出口位置可以消除消声器的通过频率,进而改善消声器中低频的消声性能。      

穿孔板的声学厚度修正

使用有限元法计算穿孔板的声学厚度修正系数,研究穿孔率、穿孔板厚度、孔径和穿孔排列形式对声学厚度的影响,获得了穿孔率低于40%的穿孔板的声学厚度修正系数.计算结果表明:穿孔板厚度、孔径和排列形式对声学厚度的影响不大;穿孔率对声学厚度影响很大.基于数值计算结果给出了声学厚度修正系数的近似表达式,利用由该表达式形成的穿孔声阻抗公式计算了穿孔管消声器的传递损失,计算结果与实验结果吻合良好,从而验证了应用该表达式预测穿孔管消声器消声性能的准确性.     

阻抗复合消声器声学性能有限元预测方法及分析

为计算和分析具有复杂结构的阻抗复合式消声器的宽频消声性能,建立了一种高效声学有限元方法,给出了不同边界条件下的边界积分处理细节,得到有限元全局系数矩阵表达式,设计出计算程序框架以实现这些算法,其求解规模和计算速度与商业软件相比有优势。为计算阻抗复合式消声器的传递损失,通过阻抗管测量和数据拟合得到了吸声材料声学特性的经验公式。计算和测量了两通穿孔阻抗复合式消声器的传递损失,二者良好的吻合验证了声学有限元方法和计算程序的正确性。研究表明,插管长度影响消声器在中高频段的消声特性,右侧隔板上穿孔会消除共振峰,中高频消声性能随着出口管穿孔率的增加而提升。      

环状气囊水消声器声学性能的预测与分析

水消声器作为一种有效的噪声控制装置被广泛应用于水管路系统,本文分别使用模态匹配法和有限元法对环状气囊水消声器的声学性能进行仿真计算,分析气囊水消声器声学特性的原理,并研究气囊水消声器不同媒介间的特性声阻抗大小关系对消声性能的影响规律。计算结果表明：由于阻抗失配关系,在气囊水消声器中气体对声波的传递起主要反射作用。随着橡胶的特性阻抗增大,橡胶会对从水中传递过来的声波起到一定的阻碍作用。当气体体积被压缩时,气体对声波的反射衰减效果会逐渐减弱,从而使得气囊水消声器的传递损失曲线整体幅值下降,消声性能减弱。     

掠过流作用下穿孔板的声阻抗

应用三维时域数值方法研究掠过流对穿孔板声阻抗的影响。建立了掠过流作用下穿孔板声阻抗计算的计算流体动力学(CFD)模型,通过时域计算得到掠过流作用下穿孔板的声阻抗,分析结构参数和掠过流马赫数对穿孔板声阻抗的影响。根据计算结果拟合掠过流作用下穿孔板声阻抗的近似表达式,利用获得的穿孔声阻抗新公式预测穿孔管消声器的传递损失,数值预测和实验结果吻合良好。计算结果表明,掠过流对穿孔板的声阻抗和穿孔管消声器的消声性能有明显影响。     

基于低频吸声超构材料的复合消声器研究*

针对管道内低频噪声难以抑制的问题，本文基于亥姆霍兹共振腔（HR）阵列吸声板和穿孔管消声器组合，设计了一种复合式宽带消声器。首先利用有限元法仿真分析传统穿孔管消声器，发现中低频消声能力较差，通过嵌入HR阵列吸声板吸收中低频噪声。采用仿真与实验的方式研究吸声板的声学性能：在400-1000 Hz频段内的平均吸声系数达到了0.88。然后对复合式消声器进行数值模拟及3D打印阻抗管实验测试对比：复合式消声器在400-1718Hz频率范围内的平均传递损失为18.15 dB ，最终实现了管道内全频带噪声有效控制。     

消声器传递损失预测的边界元模态展开混合方法

将边界元法和解析方法结合形成一种混合方法用于计算消声器的传递损失,消声器被划分成若干个子结构,解析方法和边界元方法被分别用于计算规则结构和不规则结构的阻抗矩阵,不同子结构之间通过阻抗矩阵连接起来。为减少计算时间,采用一种基于模态配点法的简化方法。对单级膨胀腔、双级膨胀腔和穿孔管阻性消声器的传递损失进行了计算,混合方法计算结果与解析方法和三维数值方法计算结果吻合良好。分析了混合方法的计算效率并与传统子结构方法进行了比较,混合方法能明显节省计算时间。     

消声器传递损失预测的边界元模态展开混合方法

将边界元法和解析方法结合形成一种混合方法用于计算消声器的传递损失,消声器被划分成若干个子结构,解析方法和边界元方法被分别用于计算规则结构和不规则结构的阻抗矩阵,不同子结构之间通过阻抗矩阵连接起来。为减少计算时间,采用一种基于模态配点法的简化方法。对单级膨胀腔、双级膨胀腔和穿孔管阻性消声器的传递损失进行了计算,混合方法计算结果与解析方法和三维数值方法计算结果吻合良好。分析了混合方法的计算效率并与传统子结构方法进行了比较,混合方法能明显节省计算时间。      

Transmission loss prediction of reactive silencers using 3-D time-domain CFD approach and plane wave decomposition technique

A predictive method is proposed to determine the transmission loss of reactive silencers using the three-dimensional (3-D) time-domain computational fluid dynamics (CFD) approach and the plane wave decomposition technique. Firstly, a steady flow computation is performed with a mass-flow-inlet boundary condition, which provides an initial condition for the following two unsteady flow computations. The first unsteady flow computation is conducted by imposing an impulse (acoustic excitation) superimposed on the constant mass flow at the inlet of the model and then adding the non-reflecting boundary condition (NRBC) when the impulse completely propagates into the silencer. The second unsteady flow computation is conducted for the case without acoustic excitation at the inlet. The time histories of pressure and velocity at the upstream monitoring point as well as history of pressure at the downstream monitoring point are recorded during the two transient computations. The differences between the two unsteady flow computational results are the corresponding acoustic quantities. Therefore, the incident sound pressure signal is obtained by using plane wave decomposition at upstream, while the transmitted sound pressure signal is just the sound pressure at downstream. Finally, those two sound pressure signals in the time-domain are transformed into the frequency-domain by Fast Fourier Transform (FFT) and then the transmission loss (TL) of silencer is determined. For the straight-through perforated tube silencers with and without flow, the numerical results agree well with the published measurements.     

A network approach for analysis of silencers with/without absorbent material

The object of this work is to establish a general approach that can analyze the performance of most of the silencers with/without sound absorbent material. Under the assumption of plane wave propagation, the transfer matrices between the two ends of straight pipe and two-duct perforated section are derived and taken as the basic elements. Based on the conditions of continuity of pressure and of mass velocity, the silencer is modeled as a network formed by the two basic elements. Then the sound attenuation characteristic of the silencers can be investigated. With this scheme the multiply connected acoustic filters can also be analyzed. Further, the porous sound absorbent material is also included in this scheme. The effect of sound absorption material on the performance of silencers is analyzed and discussed.     

Acoustic attenuation analysis of silencers with multi-chamber by using coupling method based on subdomain division technique

For multi-chamber silencers with non-uniform cross-sections at axial direction, the coupling method based on subdomain division technique is proposed. The silencer is divided into several subdomains which impedance matrixes are calculated by using suitable 3-D methods. Combining with the continuity conditions at the interfaces to solve the integral impedance matrix of the silencer, thereby the transmission loss is derived. For the double-chamber silencers, the transmission loss and computational speed results from the proposed method, the numerical mode matching (NMM) method, 3-D finite element (FE) method predictions and experimental measurements are compared, which verifies the accuracy and efficiency.     

Acoustic attenuation analysis of network systems by using impedance matrix method

An impedance matrix method is proposed to predict the acoustic attenuation characteristics of network systems. The system may contain several silencer modules and each module may be composed of complex components such as multiply connected tubes, portions with any-shaped cross-section and dissipative parts. The technique of substructuring is adopted and the system is divided into several substructure modules. Three strategies: boundary element method (BEM), numerical point collocation approach and numerical mode matching technique are introduced and the impedance matrix of each module may be computed by a certain appropriate methodology according to the dimensions and geometry of the substructure. Impedance matrix synthesis is employed to obtain the resultant impedance matrix and then transmission loss may be calculated. All the calculation results are verified by experimental measurements and 3-D BEM predictions.     

锥形颈部赫姆霍兹共振器声学性能预测

锥形颈部赫姆霍兹共振器具有更好的低频消声能力,而其声学性能尚无准确解析预测方法。为了研究其声学性能,在声学长度修正的基础上,利用一维解析方法建立了用于计算传递损失的一维修正模型。运用分割法计算锥形管内部声传播的声学长度修正,并给出了声学修正长度计算公式。采用得到的锥形管声学修正长度和一维修正模型,计算出的锥形颈部赫姆霍兹共振器频率与有限元及实验测试结果偏差在2 Hz以内,明显优于不修正的计算结果。表明锥形管声学长度修正法提高了一维解析方法的精度,从而可以快捷准确的预测锥形颈部赫姆霍兹共振器的消声性能。