Temperature impedance spectroscopy of (1 − x)Na1/2Bi1/2TiO3-xLaMg1/2Ti1/2O3 solid solutions

The dielectric properties of (1 ? x)Na_1/2Bi_1/2TiO₃-xLaMg_1/2Ti_1/2O₃ solid solutions (0 ≤ x ≤ 0.4) were studied over the temperature range 650–1030 K by measuring the impedance spectra over the frequency range 25–10⁶ Hz. The Curie temperature T _C was determined as a function of the composition of the solid solutions. It is shown that T _C decreases linearly with increasing x. The temperature dependences of the dc component (σ_dc) and the polarization component (σ′_ac) of the real part of the conductivity are found. The activation energy for the conductivity σ_dc is shown to increase abruptly as the temperature increases above approximately 770 K for all solid solution compositions. Over the temperature range corresponding approximately to the region of existence of the tetragonal phase of Na_1/2Bi_1/2TiO₃, the polarization component σ′_ac of the solid solutions, as well as that of the pure compound, is anomalously high at low frequencies, which can be due to structural inhomogeneities.     

Dielectric and piezoelectric properties of Li-substituted lead-free (Bi0.5Na0.5)TiO3–(Bi0.5K0.5)TiO3–BaTiO3 ceramics

Lead-free 0.79(Bi_0.5Na_0.5)TiO₃–0.14[Bi_0.5(K_0.5−xLi_x)]TiO₃–0.07BaTiO₃ (BNBK79 + xLi, x = 0.0, 0.1, 0.2, 0.25, 0.3, and 0.4) ceramics were prepared by conventional solid state reaction process. The crystalline structures and surface morphologies are investigated by X-ray diffraction method and scanning electron microscopy. Dielectric and piezoelectric properties were measured. With increasing of lithium substitution, the Curie temperatures of BNBK79 + xLi ceramics increase, but the maximum value of the dielectric constant decreases. And a relatively large remnant polarization of 17.6 μC/cm² and 157 pC/N of d₃₃ has been obtained when x = 0.3.     

Phase-transformation-induced microstructure in lead-free ferroelectric ceramics based on (Bi0.5Na0.5)TiO3–BaTiO3–(Bi0.5K0.5)TiO3

Lead-free ferroelectric ceramics with a morphotropic phase boundary (MPB) composition 85.4% (Bi_0.5Na_0.5)TiO₃–2.6%BaTiO₃–12.0% (Bi_0.5K_0.5)TiO₃ (BNT-BT-BKT at a molar ratio of 85.4: 2.6: 12.0) doped with 0.8?mol% Nb₂O₅ were studied for their crystalline phases and microstructure. The crystalline phases were identified using X-ray diffractometry (XRD) with the contents determined using the Rietveld refinement technique. The phase-transformation-induced microstructure was analyzed using transmission electron microscopy (TEM) and the crystal symmetries were determined using the convergent-beam electron diffraction (CBED) technique. Samples sintered at 1200°C contain a mixture of cubic (C-), tetragonal (T-) and rhombohedral (R-) phases at a ratio of C/T/R?=?56.6: 28.4: 15.0?wt%. Two types of grains are produced: one characterized by a featureless contrast consisting of nano-scale T-domains dispersed in a C-phase matrix; the other a core-shell structure with a shell containing twin and anti-phase-boundary (APB) domains coexisting with a (C?+?T)-phase mixture core. The T- and R-twin boundaries are determined to {111}_T and {110}_R, respectively, and the fault vector for T-APB to R?=?1/2?110]_T. The characteristic microstructure is discussed in terms of the reduction in the point group symmetry and changes in the unit cell volume or the Bravais lattice upon phase transformation among the C-, T- and R-phases. The twin and the APB domains are induced and explained.     

Na1/2Bi1/2TiO3体系的电子结构与极化特性

采用自洽场离散变分X_α计算方法,研究了ABO₃型钙钛矿结构无铅压电陶瓷Na_1/2Bi_1/2TiO₃体系的电子结构,分析了A,B位元素取代对Na_1/2Bi_1/2TiO₃压电陶瓷极化性能的影响.结果表明:NBT体系压电陶瓷材料存在自发极化,B位离子位移使铁电性增强,Ba,Sr与Mn离子A,B位复合取代可降低矫顽场、提高自发极化强度,从而提高材料的铁电性能,并通过实验对此结论进行了验证.     

Microstructure and electrical properties of Bi0.5Na0.5TiO3–Bi0.5K0.5TiO3–LiNbO3 lead-free piezoelectric ceramics

Lead-free piezoelectric ceramics of (1?x?y)Bi_0.5Na_0.5TiO₃–xBi_0.5K_0.5TiO₃–yLiNbO₃ (BNT–BKT–LN-x/y) have been fabricated by a conventional solid-state reaction method, and their microstructure and electrical properties have been investigated. The results of X-ray diffraction (XRD) measurement show that K⁺, Li⁺ and Nb⁵⁺ diffuse into the Bi_0.5Na_0.5TiO₃ lattices to form a solid solution with a pure perovskite structure. The BKT and LN addition has no remarkable effect on the crystal structure. However, a significant change in grain size took place. Simultaneously, with increasing amount of LN, the temperature for a ferroelectric–antiferroelectric phase transition is clearly reduced. The temperature dependence of dielectric properties suggests that the ceramics have diffuse-type phase transition characteristics. The piezoelectric constant d₃₃ and the electromechanical coupling factor k_p of the ceramics attain maximum values of 195 pC/N and 0.336 at x=0.18 and y=0.01.     

Ferroelectric properties of Pb(Zr1/2Ti1/2)O3–Pb(Zn1/3Nb2/3)O3 ceramics under compressive stress

Effects of compressive stress on the ferroelectric properties of ceramics in PZT–PZN system were investigated. The ceramics with a formula (1−x)Pb(Zr_1/2Ti_1/2)O₃–xPb(Zn_1/3Nb_2/3)O₃ or (1−x)PZT–(x)PZN (x = 0.1–0.5) were prepared by a conventional mixed-oxide method. The ferroelectric properties under the compressive stress of the PZT–PZN ceramics were observed at the stress levels up to 170 MPa using a compressometer in conjunction with a modified Sawyer–Tower circuit. It was found that with increasing compressive stress the area of the ferroelectric hysteresis (P–E) loops, the saturation polarization (P_sat), the remnant polarization (P_r), and the coercive field (E_c) decreased. These results were interpreted through the non-180° ferroelastic domain switching processes.     

Phase diagram of (1−x%)(0.89Bi0.5Na0.5TiO3–0.06BaTiO3–0.05K0.5Na0.5NbO3)–x%MnO2 lead-free anti-ferroelectric ceramics

A phase diagram for the lead-free ceramics in the (1?x%)(0.89Bi_0.5Na_0.5TiO₃–0.06BaTiO₃–0.05K_0.5Na_0.5NbO₃)–x%MnO₂ (BNBKN-x%Mn) binary system is constructed for the first time based on the ferroelectric and dielectric measurements. The ferroelectric behaviors under different temperatures suggest that the ceramics are basically of relaxor anti-ferroelectric nature near room temperature. The temperature dependent dielectric properties show that when the addition of MnO₂ increases, the relaxor anti-ferroelectric phase can be stabilized to be close to the Curie point, which corresponds to a relaxor anti-ferroelectric to paraelectric phase transition.     

Picosecond nonlinearity of GeO2–Bi2O3–PbO–TiO2 glasses at 532 and 1,064 nm

The third-order optical properties of GeO₂–Bi₂O₃–PbO–TiO₂ glasses at 532 nm and 1,064 nm were studied to evaluate their potential for optical limiting and all-optical switching. The Z-scan technique was used to determine the nonlinear (NL) refractive index, n ₂, and the NL absorption coefficient, α ₂, of samples with different amounts of the constituent oxides. Values of n ₂ ≈ + 0.7 × 10^?14 cm²/W at 1,064 nm and ≈+1.5 × 10^?14 cm²/W at 532 nm were measured. The NL absorption coefficient, α ₂, was smaller than the minimum that our apparatus can measure (α ₂ < 0.01 cm/GW) in the near-infrared (1,064 nm); in the visible region (532 nm), we obtained α ₂ ≈ 4.4 cm/GW. The set of NL parameters measured indicates the potential usefulness of the GeO₂–Bi₂O₃–PbO–TiO₂ glasses for all-optical switching at 1,064 nm and for optical limiting at 532 nm.     

Elastic–plastic deformation of Pb(Zn1/3Nb2/3)O3–(6–7)% PbTiO3 single crystals during nanoindentation

The elastic–plastic deformation behavior of (001)- and (011)-oriented single crystal solid solutions of Pb(Zn_1/3Nb_2/3)O₃–(6–7)% PbTiO₃ (PZN–PT) have been studied using a nanoindentation technique. A procedure is presented here to isolate the elastic, elastic–plastic and plastic contributions to the deformation using the unloading data, and a parameter, referred to as relaxation, is defined to characterize the elastic–plastic deformation during nanoindentations. This relaxation parameter increases with the maximum indentation load due to the higher indentation stress induced, and it also causes less recovery of the material upon indentation unloading compared to predicted pure elastic recovery. For a (001) surface, the relaxation value remains virtually unchanged within the range of the maximum indentation load of 10–50 mN, possibly due to a complete localized depoling of the non-180° domain switching. It is also found that the unpoled surface is more prone to stress-induced depolarization compared to the poled surfaces. Furthermore, by applying the continuous stiffness measurement (CSM) technique, the effects of multiple loading/unloading are studied for both (001)- and (011)-oriented PZN–PTs using the maximum indentation loads of 20 and 50 mN. With more loading/unloading cycles at higher CSM frequencies, stress-induced depolarization becomes prevalent and the contribution of the domain reorientation towards elastic recovery is significantly reduced. As a consequence, the relaxation value is increased, indicating more elastic–plastic deformation. This CSM effect is especially pronounced for poled (011) surfaces.     

Li_(2/3)H_(1/3)IO_3多晶的离子电导

文献[1]报道了在 LiIO3-HIO3 体系中存在一个新的化合物2LiIO3·HIO3(Li_(2/3_H_(1/3)IO_3).它与a-LiIO3晶格常数的差异引起了晶格畸变.通过电导的研究,可以揭示离子传导对结构参量的敏感特性,井对这种材料作为固体电解质应用作出估价.本文还研究了文献[2—4]报道的Li_(1-x)Mg_     

Synthesis and electrical properties of Pb(Mg1/3Nb2/3)O3–PbTiO3 ceramics

Ceramic compositions of a combination between lead magnesium niobate, Pb(Mg_1/3Nb_2/3)O₃, and lead titanate, PbTiO₃, were fabricated by using Mg₄Nb₂O₉ precursor technique. Their electrical properties with respect to temperature and frequency were examined and the effect of sintering conditions on phase formation, densification, microstructure and electrical properties of the ceramics were examined. It has been found that optimisation of sintering condition can lead to a highly dense and pyrochlore-free PMN–PT ceramics. The gradual decreasing of the physical properties of the sintered ceramics was related to the gradual decrease of density and inhomogeneous microstructure. The results also revealed that for the lower concentration of lead titanate a relaxor behavior is noticed with a high electrostrictive effect, which was almost hysteretic free. However, higher amount of lead titanate led to a normal ferroelectric behavior.     

Kinetics of the phase transition in crystals PbIn1/2Nb1/2O3–PbMg1/3Nb2/3O3–x PbTiO3

The time dependences of the optical transmission, velocity of sound, and elastic constants at room temperature in a number of the [001]-oriented PbIn_1/2Nb_1/2O₃–PbMg_1/3Nb_2/3O_3–x PbTiO₃ single crystals with the compositions lying both far from the morphotropic phase boundary and in its vicinity have been investigated. The analysis of the data obtained has been carried out. It has been shown that, in all the studied crystals, phase transitions induced by an electric field occur in two stages: the first stage is an incubation period associated with a small increase in the polarization of a part of the sample being in the glass phase, and the second phase (after the incubation period τ) is a rapid increase in the polarization and the formation of a long-range order. It has been found that the time τ depends on how close is the temperature of measurements to the Vogel–Fulcher temperature T _f . The closer is the temperature of measurements to the Vogel–Fulcher temperature T _f , the weaker is the electric field required to be applied to the sample in order to induce a ferroelectric phase. It has been demonstrated that the phase state of the studied crystals is unstable, which manifests itself in a strong dependence of the incubation period τ on the time between the annealing of the sample and the beginning of the measurements. The stability of the phase state depends on the PbTiO₃ concentration: an increase in the concentration leads to a significant increase in the stability.     

Mössbauer and TEM studies of the perovskite system (1-y)La2/3 $$A$$ 1/3TiO3·yLaFeO3

The microscopic nature of the Mössbauer phase analysis has been found as being particularly valuable in testing assumptions suggested by TEM results regarding the microdomain structure and the population of different lattice sites by iron ions in the perovskite system (1-y)La_{2/3 1/3}TiO₃·yLaFeO₃ with 0.04<y < 0.25 ( is an A-site vacancy). This system was found to contain only Fe₃₊-phases which are stable under normal conditions, but moderate heating in vacuo causes a partial reduction of ferric ions to ferrous ions.     

立方相Na_(1/2)Bi_(1/2)TiO_3和K_(1/2)Bi_(1/2)TiO_3的电子结构和结构不稳定性的第一性原理比较研究

采用基于密度泛函理论的第一性原理方法比较研究了Na1/2Bi1/2TiO3和K1/2Bi1/2TiO3的电子结构、离子位移势能面和Γ声子等性质.结果表明,Na1/2Bi1/2TiO3和K1/2Bi1/2TiO3的电子结构很相似,价带由O 2p电子态主导并包含部分Ti 3d和Bi 6p电子态,导带低能部分由Ti 3d空轨道构成;K取代Na后其Ti—O和Bi—O键的键强略有增加.两者的离子位移势能面也很接近,O离子的偏心位移对结构不稳定性起主导作用,且K取代Na后其作用增强.Γ声子都存在3个软模,分析表明软模主要来自O6基团的振动,K取代Na后A2u软模发生硬化.