A high-performance fluorosensor for pH measurements between 6 and 9

This study presents a high-performance ratiometric pH optode based on the fluorophore 6,8-dihydroxypyrene-1,3-disulfonic acid (DHPDS). The two pH-sensitive terminal hydroxy groups of DHPDS facilitated dual excitation/dual emission (F₁: λ_1,ex = 420 nm, λ_1,em = 462 nm; F₂: λ_2,ex = 470 nm, λ_2,em = 498 nm) properties for ratiometric (R_F1,F2 = F₁/F₂) normalization of sensor signal. The sensor demonstrated an exponentially decreasing ratiometric response with increasing pH, with a linear correlation (R² = 0.9936) between ¹⁰log(R_F1,F2) and pH within the pH interval 6-9. Precision determined as the IUPAC pooled standard deviation for the pH values 6.00, 7.01 and 9.01, was 0.0057 pH units for the fluorosensor and 0.0054 for a commercially available pH electrode used for comparison. Between the end-points of calibration at pH 7.01, the precision of the sensor was 0.0037 pH units. Effects from changes in ionic strength (I_tot, 10-700 mM) were more pronounced for the electrode, with a linear (R² = 0.9976) increase in response (δE/δpH) with increasing I_tot. The DHPDS-based fluorosensor, however, retained sensitivity (δ¹⁰log(R_F1,F2)/δpH = 0.8024 ± 0.0145), though with an overall increase in ratiometric signal with increasing I_tot. The preserved sensitivity despite changes in ionic strength was possibly a consequence from the dual photo-acidic properties of DHPDS. Analytical characteristics of immobilized DHPDS therefore not only facilitated high-performance measurements over a wide pH range, but also opened for straightforward simultaneous measurements of pH and ionic strength.     

Characterisation and deployment of an immobilised pH sensor spot towards surface ocean pH measurements

The oceans are a major sink for anthropogenic atmospheric carbon dioxide, and the uptake causes changes to the marine carbonate system and has wide ranging effects on flora and fauna. It is crucial to develop analytical systems that allow us to follow the increase in oceanic pCO₂ and corresponding reduction in pH. Miniaturised sensor systems using immobilised fluorescence indicator spots are attractive for this purpose because of their simple design and low power requirements. The technology is increasingly used for oceanic dissolved oxygen measurements.     

A high-precision ratiometric fluorosensor for pH: implementing time-dependent non-linear calibration protocols for drift compensation

We present a versatile time-dependent non-linear calibration protocol for optical sensors, implemented on the pH sensitive ratiometric fluorophore 8-hydroxypyrene-1,3,6-trisulfonic acid (HPTS) immobilized in ethyl-cellulose. The calibration protocol individually compensated for the progressive drift of calibration parameters, whereby sensor precision and accuracy, as well as applicable lifetime were improved. A severely reduced photoacidity was observed for the immobilized fluorophore, for which excited state dynamics was characterized and benefited from during measurements. Due to the significantly reduced photoacidity of HPTS immobilized in the ethyl-cellulose sensing membrane, a dual excitation/dual emission (F₁, ex/em: 405/440 nm and F₂, ex/em: 465/510 nm) ratiometric (RF₁,F₂ = F₁/F₂) sensing scheme could be used to amplify sensor response. The signal to noise (S/N) ratio was enhanced by ∼400% utilizing the dual excitation/dual emission ratiometric sensing scheme, rather than the more commonly used protocol of dual excitation/single emission for HPTS fluorescence. Apparent pK_a of the fluorophore ranged from 6.74 to 8.50, mainly determined by the immobilization procedure. The repeatability (IUPAC, pooled standard deviation) over three pH values (6.986, 7.702 and 7.828) was 0.0044 pH units for the optical sensor, compared to 0.0046 for the electrode used for standardization. Sensor analytical characteristics were thereby in principle limited by the performance of the standardization procedure.     

Assessment of Chemcatcher passive sampler for the monitoring of inorganic mercury and organotin compounds in water

Abstract

Molecularly imprinted polymers (MIPs) for 4-nitrophenol have been successfully prepared by a thermal polymerization method using 4-vinylpyridine (4-VP) and ethylene glycol dimethacrylate (EDMA) as functional monomer and cross-linker, respectively. The obtained materials were evaluated with respect to their selective recognition properties for 4-nitrophenol by HPLC using organic and aqueous eluents. Furthermore, the specific binding sites that have been created during the polymerization process were analyzed via radioligand binding assays. The successful imprinting against 4-nitrophenol provides a new opportunity for advanced separation materials used in environmental analysis.     

A novel dynamic approach for automatic microsampling and continuous monitoring of metal ion release from soils exploiting a dedicated flow-through microdialyser

In this paper, a novel concept is presented for automatic microsampling and continuous monitoring of metal ions in soils with minimum disturbance of the sampling site. It involves a hollow-fiber microdialyser that is implanted in the soil body as a miniaturized sensing device. The idea behind microdialysis in this application is to mimic the function of a passive sampler to predict the actual, rather than potential, mobility and bioavailability of metal traces. Although almost quantitative dialysis recoveries were obtained for lead ( 98%) from aqueous model solutions with sufficiently long capillaries (l 30 mm, 200 m i.d.) at perfusion rates of 2.0 L min^–1, the resistance of an inert soil matrix was found to reduce metal uptake by 30%. Preliminary investigation of the potential of the microdialysis analyser for risk assessment of soil pollution, and for metal partitioning studies, were performed by implanting the dedicated probe in a laboratory-made soil column and hyphenating it with electrothermal atomic absorption spectrometry (ETAAS), so that minute, well-defined volumes of clean microdialysates were injected on-line into the graphite furnace. A noteworthy feature of the implanted microdialysis-based device is the capability to follow the kinetics of metal release under simulated natural scenarios or anthropogenic actions. An ancillary flow set-up was arranged in such a way that a continuous flow of leaching solution — mild extractant (10^–2 mol L^–1 CaCl₂), acidic solution (10^–3 mol L^–1 HNO₃), or chelating agent (10^–4 or 10^–2 mol L^–1 EDTA) — was maintained through the soil body, while the concentration trends of inorganic (un-bound) metal species at the soil-liquid interface could be monitored at near real-time. Hence, relevant qualitative and quantitative information about the various mobile fractions is obtained, and metal-soil phase associations can also be elucidated. Finally, stimulus-response schemes adapted from neurochemical applications and pharmacokinetic studies are to be extended to soil research as an alternative means of local monitoring of extraction processes after induction of a chemical change in the outer boundary of the permselective dialysis membrane.     

A new ultrasonic measurement system for the cure monitoring of thermosetting resins and composites

Measurements of the ultrasonic sound speed of thermosetting resins and composites can be used as an in-process cure monitoring technique. Ultrasonic measurements have an advantage over other in-process techniques in that ultrasonic sensors do not make contact with the part (thus leaving no imbedded sensor or witness mark) and can make true bulk measurements of the part. A new commercially available ultrasonic cure monitoring system has been developed which easily enables ultrasonic measurements to be made in compression molding, resin transfer molding, and autoclave processes. Advancements in ultrasonic sensor technology enable the sensor to maintain good coupling to the part during thermal cycling to 260C. Data is presented showing the change in ultrasonic sound speed during the compression molding of a graphite-epoxy prepreg. The data shows a good relationship to the ionic conductivity and resistivity data collected via dielectric cure monitoring.This effort was sponsored by the Manufacturing Technology Directorate, Wright Laboratory (WL/MTX), Air Force Material Command, USAF, under cooperative agreement award(s) to NCMS. The U. S. Government is authorized to reproduce and distribute reprints for Governmental purposes notwithstanding any copyright notation thereon. The views and conclusions contained herein are those of the authors and should not be interpreted as necessarily representing the official policies or endorsements, either expressed or implied, of Wright Laboratory or the U.S. Government.     

Environmental monitoring approaches for the detection of organic contaminants in marine environments: A critical review

This review reports different approaches for monitoring the presence of organic contaminants in marine environments. From the traditional standard chromatographic methodologies coupled to different detectors to the recent advances in sensor technology, different strategies have been adopted by researchers aiming to provide more comprehensive, realistic and accurate environmental monitoring data sets. Reports on chemical analysis by different techniques of marine water and sediments, using grab and passive sampling techniques, are the most abundant in literature, showing relevant developments. Analysis of the marine biota (biomonitoring) has also been widely used as a proxy for the detection of organic chemicals in seawater, with bivalves being the most used as sentinel specie. Such biomonitoring can provide insights on bioavailability and bioaccumulation of organic pollutants, which is not possible to obtain by water and sediment analysis solely. Furthermore, effect-based methods are also presented as an important approach when it comes to obtain environmental meaningful data, such as potential toxicity and hazards posed by the complex chemical mixtures to local biota. This approach is reported to be a useful tool for screening areas without any previous knowledge on chemical composition, with subsequential qualitative and quantitative characterization being performed by chemical analysis. Finally, some of the most recent developments in sensor and biosensor technology for environmental purposes are also discussed, with some proof-of-concept studies showing promising results. However, further development and validations work is strongly advised prior to the use of those sensing platforms in real field trials.     

Determination of hydroxybupropion in human serum for routine therapeutic drug monitoring in psychiatry: A tool for dose‐individualization in treatment with bupropion

Therapeutic drug monitoring (TDM) has become a clinical routine in psychiatry. Nevertheless, for bupropion there is only one method available that is suitable for routine use. However, it involves a complex sample clean‐up. Owing to the instability of bupropion in serum, the main and active metabolite hydroxybupropion was chosen as the target substance. Therefore, a simple and robust high‐performance liquid chromatography method for the quantification of hydroxybupropion in serum was developed and validated. A volume of 30 μL serum was used for easy sample clean‐up, based on protein precipitation with acetonitrile followed by online solid‐phase extraction. As hydroxybupropion was present in high serum concentrations, UV detection was possible. Owing to the commonly available instrumentation, the method could easily be integrated in routine TDM. The newly developed method was validated following the guidelines for bioanalytical method validation of the European Medicines Agency and US Food and Drug Administration. The lower limit of quantification was 100 ng/mL (0.391 μm ) and linearity was shown between 100 and 2500 ng/mL. Intraday and interday precision ranged from 1.17 to 6.79% and from 6.07 to 9.41%, respectively. Intraday and interday accuracy ranged from 89.97 to 110.86% and from 95.05 to 101.2%. The method was shown to be selective, accurate and precise. Additionally, the method was successfully implemented in the therapeutic drug monitoring laboratory of the Department of Psychiatry, Psychosomatics and Psychotherapy at the University Hospital of Würzburg, Germany. Six months of routine analysis showed a rather low correlation between applied dose and serum concentration and therefore the necessity of TDM for dose‐individualization in the treatment with bupropion.     

A sensitive LC‐MS/MS method for the simultaneous determination of amoxicillin and ambroxol in human plasma with segmental monitoring

Amoxicillin (AMO) degrades in plasma at room temperature and readily undergoes hydrolysis by the plasma amidase. In this paper, a novel, rapid and sensitive LC‐MS/MS method operated in segmental and multiple reaction monitoring has been developed for the simultaneous determination of amoxicillin and ambroxol in human plasma. The degradation of amoxicillin in plasma was well prevented by immediate addition of 20 μL glacial acetic acid to 200 μL aliquot of freshly collected plasma samples before storage at ?80°C. The sensitivity of the method was improved with segmental monitoring of the analytes, and lower limits of quantitation of 0.5 ng/mL for ambroxol and 5 ng/mL for amoxicillin were obtained. The sensitivity of our method was five times better than those of the existing methods. Furthermore, the mass response saturation problem with amoxicillin was avoided by diluting the deproteinized plasma samples with water before injection into the LC‐MS/MS system. The method was successfully employed in a pharmacokinetic study of the compound amoxicillin and ambroxol hydrochloride tablets. Copyright © 2012 John Wiley & Sons, Ltd.     

Determination of unbound prednisolone, prednisone and cortisol in human serum and saliva by on-line solid-phase extraction liquid chromatography tandem mass spectrometry and potential implications for drug monitoring of prednisolone and prednisone in saliva

Prednisolone (PLN) and prednisone (PN) are widely used glucocorticoids. Drug monitoring of PLN and PN is not routinely done owing to the need for multiple blood sampling and challenging measurement of unbound PLN and PN in blood. Here we present a robust method for quantification of cortisol, PLN and PN in serum, ultrafiltrate and saliva by on‐line solid‐phase extraction LC‐MS/MS. The method is linear for the three analytes over the range of 6–1400 nmol/L for serum and 2–450 nmol/L for ultrafiltrate and saliva. Within‐run precision of all three analytes was <10% and total precision was <15%. This method was applied to create time–concentration profiles of cortisol, PLN and PN after an oral dose of prednisolone in a healthy volunteer. Salivary levels of PLN correlated well with ultrafiltrate levels (p < 0.01), while this correlation was only marginal for PN (p = 0.052). The PN/PLN ratio was significantly higher in saliva than in ultrafiltrate and serum (p < 0.01). Addition sums of both metabolites in saliva showed excellent correlation with those of ultrafiltrate (p < 0.01). These findings have not been presented before and may have important implications for future studies concerning drug monitoring of PLN and PN in saliva. Copyright © 2011 John Wiley & Sons, Ltd.     

A high-resolution MAS NMR study on the potential catalysts Mo/HBeta for olefin metathesis: The interaction of Mo species with HBeta zeolite

The interfacial interaction of Mo species with the HBeta zeolite was studied by multinuclear MAS NMR, XRD and N₂ adsorption. As proved by the quantitative ²⁷Al MAS NMR, this interaction is so strong as to dealuminate the framework of HBeta, and leads to a new peak appearing at −14 ppm, which indicates the formation of crystalline Al₂(MoO₄)₃. This can also be detected by XRD measurements when the Mo loading is as high as 9.0 wt.%. The corresponding quantitative ²⁹Si and ¹H MAS NMR spectra show that the amount of silanols and Brønsted acidic sites decrease obviously with increasing Mo loading. This also reveals an interaction between Mo species and HBeta support through an oxygen bridge resulting from condensation with the hydroxyls on the support. At higher Mo loadings, the interaction is so strong that it results in an extraction of aluminum from the zeolite framework, and subsequently appearance of Al₂(MoO₄)₃ and loss of Brønsted acidic sites. These can be correlated to the low catalytic activity of Mo/HBeta in metathesis of ethylene and 2-butylene to propylene.     

A simple,rapid and reliable liquid chromatography–mass spectrometry method for determination of methotrexate in human plasma and its application to therapeutic drug monitoring

A simple, rapid and reliable liquid chromatography–electrospray ionization tandem mass spectrometry method was established and validated for the determination of methotrexate in human plasma. After a straightforward protein precipitation by acetonitrile–water (70:30, v/v), methotrexate (MTX) and p‐aminoacetophenone (used as internal standard, IS) were separated on a Column C₁₈ column (50 × 2.1 mm, 3 µm; Column Technology, Fremont, CA, USA) using a gradient elution with mobile phase of acetonitrile and 0.03% acetic acid aqueous solution at a flow rate of 0.5 mL/min. The total chromatographic runtime was 5 min for each injection. Quantification detection was performed in a triple‐quadruple tandem mass spectrometer under positive mode monitoring the following mass transitions: m/z 455.3 → 308.3 for MTX and m/z 136.1 → 94.4 for IS. The calibration curve was linear over the range of 0.05–25.0 µmol/L with a lower limit of quantification of 0.05 µmol/L. The intra‐ and interday precisions were <5.2%, the accuracy varied from ?4.1 to 4.5%. The recovery was >94%. The LC‐MS/MS method showed an excellent agreement with the existing HPLC‐UV method using Passing–Bablok regression and Bland–Altman difference plot analysis. The validated LC‐MS/MS can be successfully applied to the routine therapeutic drug monitoring of MTX in clinical laboratories. Copyright © 2015 John Wiley & Sons, Ltd.     

A high throughput and selective method for the estimation of valproic acid an antiepileptic drug in human plasma by tandem LC-MS/MS

A high throughput liquid chromatography-tandem mass spectrometric (LC-MS/MS) method for the determination of valproic acid, an antiepileptic drug, in human plasma is described. It is a rapid and sensitive isocratic reversed-phase liquid chromatography-tandem mass spectrometric method equipped with turbo ion spray (TIS) source, operating in the negative ion and pseudo selective reaction monitoring (SRM) acquisition mode to quantify valproic acid. The extraction of valproic acid and hydrochlorothiazide (IS) from the plasma involved sample treatment with phosphoric acid followed by solid-phase extraction using Waters hydrophilic-lipophilic balance (HLB) cartridge giving extracts free from endogenous interferences. Sample preparation by this method yielded very good and consistent mean recoveries of 99.73 and 74.47% for valproic acid and IS, respectively. The method was linear over the dynamic range of 2.0-200.0 μg/ml (covering entire therapeutic range) with a correlation coefficient r ≥ 0.9989. The coefficient of variance (CV, %) was 7.03% at 2.0 μg/ml (LLOQ). This method was fully validated for its accuracy, precision, recovery and matrix effect especially because the pattern of elution of all the analytes may appear as flow injection type. The analyte stability was examined under conditions mimicking the sample storage, handling and analysis procedures. The method was successfully applied for bioequivalence studies in human subject samples after oral administration of 500 mg formulations.     

Exhaled breath condensate: Determination of non-volatile compounds and their potential for clinical diagnosis and monitoring. A review

Exhaled breath condensate is a promising, non-invasive, diagnostic sample obtained by condensation of exhaled breath. Starting from a historical perspective of early attempts of breath testing towards the contemporary state-of-the-art breath analysis, this review article focuses mainly on the progress in determination of non-volatile compounds in exhaled breath condensate. The mechanisms by which the aerosols/droplets of non-volatile compounds are formed in the airways are discussed with methodological consequences for sampling. Dilution of respiratory droplets is a major problem for correct clinical interpretation of the measured data and there is an urgent need for standardization of EBC. This applies also for collection instrumentation and therefore various commercial and in-house built devices are described and compared with regard to their design, function and collection parameters. The analytical techniques and methods for determination of non-volatile compounds as potential markers of oxidative stress and lung inflammation are scrutinized with an emphasis on method suitability, sensitivity and appropriateness. The relevance of clinical findings for each group of possible non-volatile markers of selected pulmonary diseases and methodological recommendations with emphasis on interdisciplinary collaboration that is essential for future development into a fully validated clinical diagnostic tool are given.     

Combining chromatography and chemometrics for the characterization and authentication of fats and oils from triacylglycerol compositional data—A review

The characterization and authentication of fats and oils is a subject of great importance for market and health aspects. Identification and quantification of triacylglycerols in fats and oils can be excellent tools for detecting changes in their composition due to the mixtures of these products. Most of the triacylglycerol species present in either fats or oils could be analyzed and identified by chromatographic methods. However, the natural variability of these samples and the possible presence of adulterants require the application of chemometric pattern recognition methods to facilitate the interpretation of the obtained data. In view of the growing interest in this topic, this paper reviews the literature of the application of exploratory and unsupervised/supervised chemometric methods on chromatographic data, using triacylglycerol composition for the characterization and authentication of several foodstuffs such as olive oil, vegetable oils, animal fats, fish oils, milk and dairy products, cocoa and coffee.     

A pH-response multifunctional nanoplatform based on NaGdF4:Yb,Er,Fe@Ce6@mSiO2-DOX for synergistic photodynamic/chemotherapy of cancer cells

Cancer is one of the major diseases that seriously threaten human health. Drug delivery nanoplatforms for tumor treatment have attracted increasing attention owing to their unique advantages such as good specificity and few side effects. This study aimed to fabricate a pH-responsive drug release multifunctional nanoplatform NaGdF₄:Yb,Er,Fe@Ce6@mSiO₂-DOX. In the platform, Fe³⁺ doping enhanced the fluorescence intensity of NaGdF₄:Yb, Er by 5.8 folds, and the mSiO₂ shell substantially increased the specific surface area of nanomaterials (559.257 m²/g). The loading rates of chlorin e6 and doxorubicin hydrochloride (DOX) on NaGdF₄:Yb,Er,Fe@Ce6@mSiO₂-DOX reached 28.58 ± 0.85% and 87.53 ± 5.53%, respectively. Additionally, the DOX release rate from the nanoplatform was only 24.4% after 72 h at pH 7.4. However, under tumor microenvironment conditions (pH 5.0), the release rate of DOX increased to 85.3% after 72 h. The nanoplatform could generate reactive oxygen species (ROS) under 980 nm near-infrared excitation. Moreover, the nanoplatform exhibited a strong comprehensive killing efficiency against cancer cells. The viabilities of HeLa, MCF-7, and HepG2 cancer cells were only 18.5, 11.4, and 9.3%, respectively, after being treated with a combination of photodynamic therapy and chemotherapy. The constructed nanoplatform exhibits great application potential in cancer treatment.