Enantioselective recognition of penicillamine enantiomers on bovine serum albumin-modified glassy carbon electrode

As a natural chiral selector, bovine serum albumin (BSA) has been used to recognize penicillamine (Pen) enantiomers through electrochemical methods. The recognition and assay rely on the stereoselectivity of BSA embedded in ultrathin Al₂O₃ sol–gel film coated on the surface of glassy carbon electrode (BSA/GCE). The enantioselective interaction between Pen enantiomers and BSA was monitored by cyclic voltammetry and electrochemical impedance spectroscopy measurements, from which larger response signals were obtained from d-Pen. The factors influencing the performance of the modified biosensor were also investigated. The association constant (K) was calculated to be 1.93?×?10⁴?L?mol^?1 for d-Pen and 1.20?×?10³?L?mol^?1 for l-Pen. A good linear response was exhibited with the concentration of Pen enantiomers by BSA/GCE over the range of 1?×?10^?8–1?×?10^?1?mol?L^?1 with a detection limit of 3.31?×?10^?9?mol?L^?1.     

Study of the binding equilibrium between Zn(II) and HSA by capillary electrophoresis-inductively coupled plasma optical emission spectrometry

A new method has been developed for following the interaction between zinc ion and human serum albumin (HSA) by capillary electrophoresis-inductively coupled plasma optical emission spectrometry. Under optimized experimental conditions, the detection limit (3σ) for free Zn²⁺ ion was found to be 1.34 μM by running 11 replicates of the reagent blank. The RSD was less than 3% and the recovery was more than 98.13%. The linear range of zinc ion concentration was between 5.1 μM and 0.3 M. The measured Zn(II)-HSA combination values of n₁ and K₁ for primary binding of Zn²⁺ to HSA were 1.09 and 2.29 × 10⁵ L mol⁻¹, respectively. The measured values of n₂ and K₂ for the non-specific binding of Zn²⁺ to HSA were 8.96 and 6.65 × 10³ L mol⁻¹, respectively. This new method allows rapid analysis of a small amount of sample, simple operation, while avoiding long periods of dialysis and eliminating interference from other metal ions. This method provides a reliable and convenient new way for studying interactions between metal ions and biomolecules.     

Myoglobin/arylhydroxylamine film modified electrode: Direct electrochemistry and electrochemical catalysis

The adsorption processes and electrochemical behavior of 4-nitroaniline (4-NA) adsorbed onto glassy carbon electrodes (GCE) have been investigated in aqueous 0.1 M nitric acid (HNO₃) electrolyte solutions using cyclic voltammetry (CV). 4-NA adsorbs onto GCE surfaces, and upon potential cycling past −0.2 V, is transformed into the arylhydroxylamine (ArHA) derivative which exhibits a well-behaved pH dependent redox couple centered at 0.32 V at pH 1.5. It is noted as arylhydroxylamine modified glassy carbon electrodes (HAGCE). This modified electrode can be readily used as an immobilization matrix to entrap proteins and enzymes. In our studies, myoglobin (Mb) was used as a model protein for investigation. A pair of well-defined reversible redox peaks of Mb (Fe(III)-Fe(II)) was obtained at the Mb/arylhydroxylamine modified glassy carbon electrode (Mb/HAGC) by direct electron transfer between the protein and the GCE. The formal potential (E^0′), the apparent coverage (Γ^*) and the electron-transfer rate constant (k_s) were calculated as −0.317 V, 8.26 × 10⁻¹² mol/cm² and 51 ± 5 s⁻¹, respectively. Dramatically enhanced biocatalytic activity was exemplified at the Mb/HAGC electrode by the reduction of hydrogen peroxide (H₂O₂), trichloroacetic acid (TCA) and oxygen (O₂). The Mb/arylhydroxylamine film was also characterized by UV-visible spectroscopy (UV-vis), scanning electron microscope (SEM) indicating excellent stability and good biocompatibility of the protein in the arylhydroxylamine modified electrode. This new Mb/HAGC electrode exhibited rapid electrochemical response (2 s) for H₂O₂ and had good stability in physiological condition, showing the potential applicability of the films in the preparation of third generation biosensors or bioreactors based on direct electrochemistry of the proteins.     

A sandwich-type DNA biosensor based on electrochemical co-reduction synthesis of graphene-three dimensional nanostructure gold nanocomposite films

A novel electrochemical DNA biosensor based on graphene-three dimensional nanostructure gold nanocomposite modified glassy carbon electrode (G-3D Au/GCE) was fabricated for detection of survivin gene which was correlated with osteosarcoma. The G-3D Au film was prepared with one-step electrochemical coreduction with graphite oxide and HAuCl₄ at cathodic potentials. The active surface area of G-3D Au/GCE was 2.629 cm², which was about 3.8 times compared to that of a Au-coated GCE under the same experimental conditions, and 8.8 times compared to a planar gold electrode with a similar geometric area. The resultant nanocomposites with high conductivity, electrocatalysis and biocompatibility were characterized by scanning electron microscopy (SEM), cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). A “sandwich-type” detection strategy was employed in this electrochemical DNA biosensor and the response of this DNA biosensor was measured by CV and amperometric current–time curve detection. Under optimum conditions, there was a good linear relationship between the current signal and the logarithmic function of complementary DNA concentration in a range of 50–5000 fM with a detection limit of 3.4 fM. This new biosensor exhibited a fast amperometric response, high sensitivity and selectivity and has been used in a polymerase chain reaction assay of real-life sample with a satisfactory result.     

Evaluation of the enantioselective binding of imazalil to human serum albumin by capillary electrophoresis

In this work, a methodology for the evaluation of enantioselective binding of imazalil (IMA) enantiomers to human serum albumin (HSA) that does not require the separation of free and bound to HSA fractions is developed. This methodology comprises the incubation of IMA–HSA designed mixtures for 30 min directly in the capillary electrophoresis system and the subsequent direct injection and chiral separation of IMA employing highly sulfated β‐cyclodextrin as chiral selector and the complete filling technique. Two mathematical approaches were used to estimate apparent affinity constants (K₁), protein binding and enantioselectivity (ES) for both enantiomers of IMA. Moderate enantioselective binding of IMA enantiomers to HSA (ES = 2.0) was shown by the 1:1 stoichiometry and log K₁ values of 3.4 ± 0.4 and 3.1 ± 0.3 for the first and second eluted enantiomers, respectively. Copyright © 2015 John Wiley & Sons, Ltd.     

Nucleic acid biosensor for detection of hepatitis B virus using 2,9-dimethyl-1,10-phenanthroline copper complex as electrochemical indicator

In this study, an electrochemical DNA biosensor was developed based on the recognition of target DNA by hybridization detection. The study was carried out using glassy carbon electrode (GCE) modified with lable-free 21-mer single-stranded oligonucleotides related to hepatitis B virus sequence via covalent immobilization and [Cu(dmp)(H₂O)Cl₂] (dmp = 2,9-dimethyl-1,10-phenanthroline) as an electrochemical indicator, whose sizes are comparable to those of the small groove of native double-duplex DNA. The method, which is simple and low cost, allows the accumulation of copper complex within the DNA layer. Electochemical detection was performed by cyclic voltammetry and differential pulse voltammetry over the potential range where the [Cu(dmp)(H₂O)Cl₂] was active. Numerous factors affecting the probe immobilization, target hybridization, and indicator binding reactions were optimized to maximize the sensitivity and speed the assay time. With this approach, a sequence of the hepatitis B virus could be quantified over the ranges from 8.82 × 10⁻⁸ to 8.82 × 10⁻⁷ M with a linear correlation of r = 0.9937 and a detection limit of 7.0 × 10⁻⁸ M. The [Cu(dmp)(H₂O)Cl₂] signal observed from probe sequence before and after hybridization with four bases mismatch containing sequence is lower than that observed after hybridization with complementary sequence.     

白杨素与不同构型人血清白蛋白的作用机制

采用多种光谱学手段研究了白杨素(CHR)和不同构型人血清白蛋白(HSA)相互作用的分子机制.研究表明,白杨素能使蛋白质荧光发射峰发生静态淬灭,同时,白杨素的紫外吸收谱带也发生了明显的位移,说明与蛋白质的结合可使白杨素分子中的酚羟基发生解离.蛋白质还可以引起白杨素荧光发射峰强度的明显增强.利用荧光淬灭和荧光增强两种模式计算得到的白杨素和人血清白蛋白在生理条件下(pH 7.4)的结合常数(KA)分别为(9.97±0.24)×104和(9.75±0.11)×104L mol-1,其结合比例为1:1.随着pH值的降低,蛋白质与白杨素的结合常数逐渐减小,这与蛋白质的构型变化有关.根据不同异构体血清蛋白质的结构特征,判定白杨素在蛋白质分子上的结合位置位于IIA亚域的Site I活性位点.结合分子模拟,讨论了白杨素与蛋白质分子的结合机制.     

Electrical detection of deoxyribonucleic acid hybridization based on carbon-nanotubes/nano zirconium dioxide/chitosan-modified electrodes

A novel and sensitive electrochemical DNA biosensor based on nanoparticles ZrO₂ and multi-walled carbon nanotubes (MWNTs) for DNA immobilization and enhanced hybridization detection is described. The MWNTs/nano ZrO₂/chitosan-modified glassy carbon electrode (GCE) was fabricated and oligonucleotides were immobilized to the GCE. The hybridization reaction on the electrode was monitored by differential pulse voltammetry (DPV) analysis using electroactive daunomycin as an indicator. Compared with previous DNA sensors with oligonucleotides directly incorporated on carbon electrodes, this carbon nanotube-based assay with its large surface area and good charge-transport characteristics increased DNA attachment quantity and complementary DNA detection sensitivity. The response signal increases linearly with the increase of the logarithm of the target DNA concentration in the range of 1.49 × 10⁻¹⁰ to 9.32 × 10⁻⁸ mol L⁻¹ with the detection limit of 7.5 × 10⁻¹¹ mol L⁻¹ (S/N = 3). The linear regression equation is I = 32.62 + 3.037 log C_DNA (mol L⁻¹) with a correlation coefficient value of 0.9842. This is the first application of carbon nanotubes combined with nano ZrO₂ to the fabrication of an electrochemical DNA biosensor with a favorable performance for the rapid detection of specific hybridization.     

An electrochemical DNA-sensor developed with the use of methylene blue as a redox indicator for the detection of DNA damage induced by endocrine-disrupting compounds

An electrochemical biosensor capable of indirect detection of DNA damage induced by any one of the three endocrine-disrupting compounds (EDCs) – bisphenol A (BPA), 4-nonylphenol (NP) and 4-t-octylphenol (OP), has been researched and developed. The methylene blue (MB) dye was used as the redox indicator. The glassy carbon electrode (GCE) was modified by the assembled dsDNA/graphene oxide-chitosan/gold nano-particles to produce a dsDNA/GO-CS/AuNPs/GCE sensor. It was characterized with the use of electrochemical impedance spectroscopy (EIS), cyclic voltammetry (CV) and scanning electron microscopy (SEM) techniques. The loading/release of the MB dye by the dsDNA/GO-CS/AuNPs film was investigated, and the results showed that the process was reversible. Based on this, the sensor was used to measure the difference between the loading capabilities of intact and damaged dsDNA in the films. The sensor was then successfully applied to detect DNA damage electrochemically. The differential pulse voltammetry (DPV) peak current ratio for MB, observed before and after DNA damage, increased linearly in the presence the BPA, NP or OP compounds; the treatment range was 10–60 min, and the respective damage rates were 0.0069, 0.0044 and 0.0031 min⁻¹, respectively. These results were confirmed by the binding constants: 2.09 × 10⁶ M⁻¹ (BPA-DNA), 1.28 × 10⁶ M⁻¹ (NP-DNA) and 9.33 × 10⁵ M⁻¹ (OP-DNA), all of which were obtained with the use of differential pulse stripping voltammetry (DPSV).     

A sensitive DNA biosensor based on a facile sulfamide coupling reaction for capture probe immobilization

A novel DNA biosensor was fabricated through a facile sulfamide coupling reaction. First, the versatile sulfonic dye molecule of 1-amino-2-naphthol-4-sulfonate (AN-SO₃⁻) was electrodeposited on the surface of a glassy carbon electrode (GCE) to form a steady and ordered AN-SO₃⁻ layer. Then the amino-terminated capture probe was covalently grafted to the surface of SO₃⁻-AN deposited GCE through the sulfamide coupling reaction between the amino groups in the probe DNA and the sulfonic groups in the AN-SO₃⁻. The step-by-step modification process was characterized by electrochemistry and attenuated total reflectance Fourier transform infrared (ATR-FTIR) spectroscopy. Using Ru(NH₃)₆³⁺ as probe, the probe density and the hybridization efficiency of the biosensor were determined to be 3.18 × 10¹³ strands cm⁻² and 86.5%, respectively. The hybridization performance of the biosensor was examined by differential pulse voltammetry using Co(phen)₃^3+/2+ (phen = 1,10-phenanthroline) as the indicator. The selectivity experiments showed that the biosensor presented distinguishable response after hybridization with the three-base mismatched, non-complementary and complementary sequences. Under the optimal conditions, the oxidation peak currents of Co(phen)₃^3+/2+ increased linearly with the logarithm values of the concentration of the complementary sequences in the range from 1.0 × 10⁻¹³ M to 1.0 × 10⁻⁸ M with a regression coefficient of 0.9961. The detection limit was estimated to be 7.2 × 10⁻¹⁴ M based on 3σ.     

Differential pulse voltammetric simultaneous determination of noradrenalin and acetaminophen using a hematoxylin biosensor

A highly efficient noradrenalin (NA) biosensor was fabricated on the basis of hematoxylin electrodeposited on a glassy carbon electrode, GCE. The cyclic voltammetric responses of the hematoxylin biosensor at various scan rates, which were obtained in a 0.25 mmol L⁻¹ NA solution, showed the characteristic shape typical of an EC_cat process. The kinetic parameters such as electron transfer coefficient, α, the catalytic electron transfer rate constant, k′, and the standard catalytic electron transfer rate constant, k⁰, for oxidation of NA at the hematoxylin biosensor surface were estimated using cyclic and RDE voltammetry. The peaks of differential pulse voltammetric (DPV) for NA and acetaminophen (AC) oxidation at the hematoxylin biosensor surface were clearly separated from each other when they co-exited in the physiological pH (pH 7.0). It was, therefore, possible to simultaneously determine NA and AC in the samples at a hematoxylin biosensor. Linear calibration curves were obtained for 5.0 × 10⁻¹ to 65.40 μmol L⁻¹ and 65.40-274.20 μmol L⁻¹ of NA, and for 12.00-59.10 μmol L⁻¹ and 59.10-261.70 μmol L⁻¹ of AC. The sensitivities of the biosensor to NA in the absence and presence of AC were found virtually the same, which indicates the fact that the electrocatalytic oxidation processes of NA are independent of AC and, therefore, simultaneous or independent measurements of the two analytes (NA and AC) are possible without any interference. The results of 16 successive measurements show an average voltammetric peak current of 1.13 ± 0.03 μA for an electrolyte solution containing 5.00 μmol L⁻¹ NA. The hematoxylin biosensor has been satisfactorily used for the determination of NA and AC in pharmaceutical formulations. The results obtained, using the biosensor, are in very good agreement with those declared in the label of pharmaceutical inhalation products.     

Electrochemical deoxyribonucleic acid biosensor based on carboxyl functionalized graphene oxide and poly-l-lysine modified electrode for the detection of tlh gene sequence related to vibrio parahaemolyticus

A carboxyl functionalized graphene oxide (GO-COOH) and electropolymerized ploy-l-lysine (PLLy) modified glassy carbon electrode (GCE) was fabricated and used for the construction of an electrochemical deoxyribonucleic acid (DNA) biosensor. The NH₂ modified probe ssDNA sequences were immobilized on the surface of GO-COOH/PLLy/GCE by covalent linking with the formation of amide bonds, which was stable and furthur hybridized with the target ssDNA sequence. Differential pulse voltammetry (DPV) was used to monitor the hybridization events with methylene blue as electrochemical indicator, which gave a sensitive reduction peak at −0.287 V (vs. SCE). Under the optimal conditions the reduction peak current was proportional to the concentration of tlh gene sequence in the range from 1.0 × 10⁻¹² to 1.0 × 10⁻⁶ mol L⁻¹ with a detection limit as 1.69 × 10⁻¹³ mol L⁻¹ (3σ). The polymerase chain reaction products of tlh gene from oyster samples were detected with satisfactory results, indicating the potential application of this electrochemical DNA sensor.     

Sensitive DNA biosensor improved by Luteolin copper(II) as indicator based on silver nanoparticles and carbon nanotubes modified electrode

A novel and sensitive electrochemical DNA biosensor has been developed for the detection of DNA hybridization. The biosensor was proposed by using copper(II) complex of Luteolin C₃₀H₁₈CuO₁₂ (CuL₂) as an electroactive indicator based on silver nanoparticles and multi-walled carbon nanotubes (Ag/MWCNTs) modified glassy carbon electrode (GCE). In this method, the 4-aminobenzoic acid (4-ABA) and Ag nanoparticles were covalently grafted on MWCNTs to form Ag/4-ABA/MWCNTs. The proposed method dramatically increased DNA attachment quantity and complementary ssDNA detection sensitivity for its large surface area and good charge-transport characteristics. DNA hybridization detection was performed using CuL₂ as an electroactive indicator. The CuL₂ was synthesized and characterized using elemental analysis (EA) and IR spectroscopy. Cyclic voltammetry (CV) and fluorescence spectroscopy were used to investigate the interaction between CuL₂ and ds-oligonucleotides (dsDNA). It was revealed that CuL₂ presented high electrochemical activity on GCE, and it could be intercalated into the double helices of dsDNA. The target ssDNA of the human hepatitis B virus (HBV) was quantified in a linear range from 3.23 × 10⁻¹² to 5.31 × 10⁻⁹ M (r = 0.9983). A detection limit of 6.46 × 10⁻¹³ M (3σ, n = 11) was achieved.     

Spectrofluorimetric determination of human serum albumin using a doxycycline-europium probe

A new spectrofluorimetric method is proposed for determination of human serum albumin (HSA) with the limit of detection at ng levels. Using doxycycline (DC)-europium (Eu³⁺) as a fluorescent probe, in a buffer solution of pH 10.2, HSA can remarkably enhance the fluorescence intensity of the DC-Eu³⁺ complex at 612 nm and the enhanced fluorescence intensity of Eu³⁺ is proportional to the concentration of HSA. Optimum conditions for the determination of HSA are also investigated. The linear ranges for HSA are 0-9.2 and 9.2-34.5 μg ml⁻¹ with limits of detection of 64 and 115 ng ml⁻¹, respectively. This method is simple, practical and relatively free of interference from coexisting substances, as well as much more sensitive than most of the existing assays. The determination results for human serum and urine samples are identical to those by the AOAO method, with relative standard deviations of five determinations of 1.1-3.6%. By the Rosenthal graphic method, the binding number and association constant of human serum albumin with the probe are 1.8 and 3.71×10⁵ l mol⁻¹, respectively.     

Modification of glassy carbon electrode with a polymer/mediator composite and its application for the electrochemical detection of iodate

A modified glassy carbon electrode was prepared by depositing a composite of polymer and mediator on a glassy carbon electrode (GCE). The mediator, flavin adenine dinucleotide (FAD) and the polymer, poly(3,4-ethylenedioxythiophene) (PEDOT) were electrochemically deposited as a composite on the GCE by applying cyclic voltammetry (CV). This modified electrode is hereafter designated as GCE/PEDOT/FAD. FAD was found to significantly enhance the growth of PEDOT. Electrochemical quartz crystal microbalance (EQCM) analysis was performed to study the mass changes in the electrode during the electrodeposition of PEDOT, with and without the addition of FAD. The optimal cycle number for preparing the modified electrode was determined to be 9, and the corresponding surface coverage of FAD (Γ_FAD) was ca. 5.11 × 10⁻¹⁰ mol cm⁻². The amperometric detection of iodate was performed in a 100 mM buffer solution (pH 1.5). The GCE/PEDOT/FAD showed a sensitivity of 0.78 μA μM⁻¹ cm⁻², a linear range of 4–140 μM, and a limit of detection of 0.16 μM for iodate. The interference effects of 250-fold Na⁺, Mg²⁺, Ca²⁺, Zn²⁺, Fe²⁺, Cl⁻, NO₃⁻, I⁻, SO₄²⁻ and SO₃²⁻, with reference to the concentration of iodate were negligible. The long-term stability of GCE/PEDOT/FAD was also investigated. The GCE/PEDOT/FAD electrode retained 82% of its initial amperometric response to iodate after 7 days. The GCE/PEDOT/FAD was also applied to determine iodate in a commercial salt.     

Electrodeposited nitrogen-doped graphene/carbon nanotubes nanocomposite as enhancer for simultaneous and sensitive voltammetric determination of caffeine and vanillin

A nitrogen-doped graphene/carbon nanotubes (NGR–NCNTs) nanocomposite was employed into the study of the electrochemical sensor via electrodeposition for the first time. The morphology and structure of NGR–NCNTs nanocomposite were investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM), respectively. Meanwhile, the electrochemical performance of the glassy carbon electrode (GCE) modified with electrodeposited NGR–NCNTs (ENGR–NCNTs/GCE) towards caffeine (CAF) and vanillin (VAN) determination was demonstrated by cyclic voltammetry (CV) and square wave voltammetry (SWV). Under optimal condition, ENGR–NCNTs/GCE exhibited a wide linearity of 0.06–50 μM for CAF and 0.01–10 μM for VAN with detection limits of 0.02 μM and 3.3 × 10⁻³ μM, respectively. Furthermore, the application of the proposed sensor in food products was proven to be practical and reliable. The desirable results show that the ENGR–NCNTs nanocomposite has promising potential in electrocatalytic biosensor application.     

Studies on electrochemical behaviors of acyclovir and its voltammetric determination with nano-structured film electrode

A multi-wall carbon nanotubes (MWNTs)-dihexadecyl hydrogen phosphate (DHP) film-coated glassy carbon electrode (GCE) was fabricated, and the electrochemical behaviors of acyclovir on the MWNTs-DHP film-coated GCE were investigated by using cyclic voltammetry (CV), linear sweep voltammetry (LSV), electrochemical impedance spectroscopy (EIS) and chronocoulometry (CC). The oxidation peak current of acyclovir increased significantly and the peak potential shifted negatively at the MWNTs-DHP film-modified GCE, compared with that at a bare GCE. The results showed that this nano-structured film electrode exhibited excellent enhancement effects on the electrochemical oxidation of acyclovir. Consequently, a simple and sensitive electroanalytical method was developed for the determination of acyclovir. The oxidation peak current was proportional to the concentration of acyclovir from 8.0 × 10⁻⁸ to 1.0 × 10⁻⁵ mol/L. The detection limit was about 3.0 × 10⁻⁸ mol/L for 60 s accumulation at 0.00 V. The proposed method was demonstrated by using acyclovir tablets and the result was satisfying.     

Amperometric detection of dopamine based on tyrosinase-SWNTs-Ppy composite electrode

A novel 3-dimensional single wall carbon nanotubes (SWNTs)-polypyrrole (Ppy) composite was prepared as an electrode by chemically polymerizing polypyrrole onto SWNTs using a LiClO₄ oxidant. This composite electrode was characterized by scanning electron microscopy (SEM) and cyclic voltammetry with 1 mM [Fe(CN)₆]⁻³/[Fe(CN)₆]⁻⁴. The SWNTs were thickly coated with chemically polymerized polypyrrole and the composite had many surface pores and crevices which could enhance mass transfer. The SWNTs-Ppy composite electrode showed a large specific surface area (30 m²/g) and a good reproducible current response, at about 100 times the peak current of a glassy carbon electrode (GCE). The diffusion coefficient was calculated to be 4.81 × 10⁻⁶ cm²/s. As a biosensor application, tyrosinase was immobilized on the functionalized SWNTs and tyrosinase-SWNTs-Ppy composite was prepared in the same manner. This tyrosinase-SWNT-Ppy composite electrode was used for amperometric detection of dopamine in the presence of ascorbic acid and showed high sensitivity (467 mA/M cm²) and lower detection limit (5 μM) compared to previous reports.     

Amperometric sulfite sensor based on multiwalled carbon nanotubes/ferrocene-branched chitosan composites

A novel amperometric sensor for the determination of sulfite was fabricated based on multiwalled carbon nanotubes (MWCNTs)/ferrocene-branched chitosan (CHIT-Fc) composites-covered glassy carbon electrode (GCE). The electrochemical behavior of the sensor was investigated in detail by cyclic voltammetry. The apparent surface electron transfer rate constant (K_s) and charge transfer coefficient (α) of the CHIT-Fc/MWCNTs/GCE were also determined by cyclic voltammetry, which were about 1.93 cm s⁻¹ and 0.42, respectively. The sensor displayed good electrocatalytic activity towards the oxidation of sulfite. The peak potential for the oxidation of sulfite was lowered by at least 330 mV compared with that obtained at CHIT/MWCNTs/GCE. In optimal conditions, linear range spans the concentration of sulfite from 5 μM to 1.5 mM and the detection limit was 2.8 μM at a signal-to-noise ratio of 3. The proposed method was used for the determination of sulfite in boiler water. In addition, the sensor has good stability and reproducibility.     

A novel electrochemical biosensor based on the hemin-graphene nano-sheets and gold nano-particles hybrid film for the analysis of hydrogen peroxide

Hydrogen peroxide is an important analyte in biochemical, industrial and environmental systems. Therefore, development of novel rapid and sensitive analytical methods is useful. In this work, a hemin-graphene nano-sheets (H-GNs)/gold nano-particles (AuNPs) electrochemical biosensor for the detection of hydrogen peroxide (H₂O₂) was researched and developed; it was constructed by consecutive, selective modification of the GCE electrode. Performance of the H-GNs/AuNPs/GCE was investigated by chronoamperometry, and AFM measurements suggested that the graphene flakes thickness was ∼1.3 nm and that of H-GNs was ∼1.8 nm, which ultimately indicated that each hemin layer was ∼0.25 nm. This biosensor exhibited significantly better electrocatalytic activity for the reduction of hydrogen peroxide in comparison with the simpler AuNPs/GCE and H-GNs/GCE; it also displayed a linear response for the reduction of H₂O₂ in the range of 0.3 μM to 1.8 mM with a detection limit of 0.11 μM (S N⁻¹ = 3), high sensitivity of 2774.8 μA mM⁻¹ cm⁻², and a rapid response, which reached 95% of the steady state condition within 5 s. In addition, the biosensor was unaffected by many interfering substances, and was stable over time. Thus, it was demonstrated that this biosensor was potentially suitable for H₂O₂ analysis in many types of sample.