Methane steam reforming over rhodium promoted Ni/Al2O3 catalysts

The effect of Rh addition upon catalyst characteristics and performance in methane steam reforming was investigated using Rh-promoted Ni/Al₂O₃ catalysts. The number of reduced metal atoms exposed on the surface increased for the Rh-promoted catalysts. Rh-promoted catalysts showed an increase in CH₄ reforming activity; however, constant turnover frequencies for promoted and unpromoted catalysts suggest that the increase in the number of metal surface atoms caused the activity enhancement. Rh also facilitated reduction of Ni/Al₂O₃.     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

Ni/Al2O3改性催化剂催化重整生物油模拟物制氢研究

制备了Ni/Al₂O₃、Ni-Cu/Al₂O₃、Ni-Co/Al₂O₃和Ni-Co-Cu/Al₂O₃催化剂,研究了Co和Cu对生物油水蒸气催化重整的影响。实验表明,Co 能促进水汽变换(WGS)反应,提高氢气的产率,Cu能抑制反应中焦炭的形成,提高催化剂的稳定性。对催化剂Ni-Co-Cu/Al₂O₃进行工艺条件考察,当900 ℃、水油比为6 g/g、质量空速(WHSV)为1 h^-1时,碳选择性达到87.5%,氢气产率达到84.2%,潜在氢气产率达到92.4%。     

Ru/Al2O3-catalyzed transfer dehydrogenation of alcohols

Summary Primary and secondary alcohols were oxidized to their corresponding aldehydes or ketones in good yields using Ru/Al₂O₃ as catalyst in the presence of acetone. The catalyst can be recovered by simple filtration and reused after washing with acetone.     

The influence of La2O3 and TiO2 on NiO/MgO/α-Al2O3

Summary The effect of La₂O₃ and TiO₂ on product selectivity, methane conversion and coke formation over NiO/MgO/ α -Al₂O₃ catalyst were studied in a simultaneous steam and CO₂ reforming of methane to syngas. La₂O₃ and TiO₂ were added to the catalyst via incipient wetness impregnation and bulk precipitation techniques and catalyst activity was tested in a fixed bed quartz reactor. Results reveal that although the addition of these oxides has no effect on the product selectivity and methane conversion, but can reduce coke formation on the surface of the catalysts as it can enhance the mobility of lattice oxygen anions. The results further show that the catalysts prepared by bulk precipitation technique decrease the coke formation more effectively.     

Propane oxidation over Pd/LaFe0.8Co0.2O3 catalyst

Pd/LaFe_0.8Co_0.2O₃ was found to be more active than the Pd/Al₂O₃ catalyst in propane oxidation. Activity and the oxidation state of palladium were strongly affected by the redox ratio (S) of reactants. Higher propane conversion could be obtained under rich conditions at higher temperatures, contributing to steam reforming. The presence of excess steam would bring about inhibition and oscillation.     

Direct synthesis of hydrogen peroxide from H2/O2 using Pd/Al2O3 catalysts

Pd/Al₂O₃ catalysts were prepared by the impregnation method and were used for the direct formation of hydrogen peroxide from H₂ and O₂. The H₂O₂ concentration and selectivity were strongly dependent on the solubility of hydrogen in the reaction medium. The modification of the support by halogenate has a beneficial effect on the selectivity. The state of the active Pd on Pd/Al₂O₃ catalysts was studied using X-ray photoelectron spectroscopy, and Pd(0) was found to be active.     

Ring opening of methylcyclopentane over Al2O3 and SiO2 supported Rh catalysts

Hydrogenolytic ring opening of methylcyclopentane (MCP) was investigated on Rh/Al₂O₃ and Rh/SiO₂ catalysts, prepared by the incipient wetness method. Strong dependence can be seen in the yield and distribution of ring opening products as a function of temperature and hydrogen pressure. They depended also on the support used. The ring opening reaction required high hydrogen coverage, and was not random (hindered in the vicinity of the methyl group), thus, mainly 2-methylpentane (2MP) and 3-methylpentane (3MP) were formed. The fragments consisted of C₁–C₅ alkanes, with methane andi-pentane as main fragments. This means the possibility of breaking two C−C bonds during one sojourn of the reactant on the catalyst, both taking place far from the substituent. The loose positive correlation between the ratios ofi-pentane/n-pentane and 3MP/n-hexane seems to support this conclusion. Dedicated to Professor Pál Tétényi on the occasion of his 70th birthday     

PREPARATION OF Ru/Al2O3 CATALYSTS FROM RuCl3

Increasing reduction time increases ruthenium reduction, but even after 6 h, ruthenium is not completely reduced and chlorine is not completely eliminated in Ru/Al₂O₃ prepared from RuCl₃.     

Selective Catalytic Reduction of NO with Propene over Au/Fe2O3/Al2O3 Catalysts

A series of Au/Fe₂O₃/Al₂O₃ catalysts were prepared by the homogeneous deposition-precipitation method. The catalytic activity of the catalyst samples for selective catalytic reduction of NO by propene under oxygen-rich atmosphere was evaluated. The results showed that 2%Au/10%Fe₂O₃/Al₂O₃ exhibited good low-temperature activity. The maximum of NO conversion reached 43% at 300 °C, while it was only 21% over the 2%Au/Al₂O₃ catalyst at the same temperature. The addition of 2% steam to the feed gas had little effect on the catalytic activity. X-ray diffraction results indicated that both Au and Fe₂O₃ particles were highly dispersed over Al₂O₃. H₂-temperature-programmed reduction results indicated that there was strong interaction between Au and Fe₂O₃, which made the reduction of Fe₂O₃ easy. The synergistic effect between Au and Fe₂O₃ was probably responsible for the good catalytic performance of the Au/Fe₂O₃/Al₂O₃ catalyst at low temperature.     

Activity of bifunctional Pt-Dy/Al2O3 catalysts in hydrocarbon reactions

The conversions ofn-hexane and methylcyclopentane on Pt–Dy/Al₂O₃ containing different amounts of Dy have been investigated in a pulsed microcatalytic reactor. The poisoning effect of thiophene on the activity of Pt–Dy/Al₂O₃ for n-hexane conversion has been studied. The influence of Dy over Pt–Dy/Al₂O₃ is also discussed.     

Selective catalytic reduction of NO over metal oxide or noble metal-doped In2O3/Al2O3 catalysts by propene in the presence of oxygen

The activities of metal oxide CuO, SnO₂, CoO, Ag₂O, ZnO or noble metal Pt, Pd, Rh-doped In₂O₃/Al₂O₃ catalysts for selective catalytic reduction of NO by propene were investigated. The temperature windows for NO reduction over noble metal-doped In₂O₃/Al₂O₃ catalysts were shifted and broaden slightly compared with single component catalyst alone. This revised version was published online in June 2006 with corrections to the Cover Date.     

Two-stage catalytic system of Sn/Al2O3 and Pt/Al2O3for NO reduction by propene in lean conditions

The Pt/Al₂O₃, Sn/Al₂O₃catalysts were prepared by the single sol-gel method. The two-stage Sn/Al₂O₃and Pt/Al₂O₃catalyst in series for NO reduction with propene were investigated. The coexistance of water vapor enhanced the activity at medium temperature of 300-400^oC, and the NO conversion was above 50% at 225 to 500^oC even in the presence of water vapor and SO₂. This revised version was published online in August 2006 with corrections to the Cover Date.     

Influence of Pd-Ce interaction and chlorine ion on hydrodesulfurization reaction: The activity and sulfur tolerance of the Pd-Ceo2/Al2O3 catalyst

CeO₂ promoted palladium catalysts supported on Al₂O₃ were prepared using the impregnation (IM) and the deposition-precipitation (DP) methods. The activities and sulfur tolerance of the catalysts for hydrodesulfurization (HDS) were detected with thiophene HDS as probe reaction. H₂ adsorption, XRD, FTIR, NH₃-TPD, XPS were used to characterize the catalysts. The Pd-CeO₂/Al₂O₃ (IM) catalyst was highly active for the HDS reaction, and it had much stronger sulfur tolerance than the Pd/Al₂O₃ catalyst. Pd-CeO₂/Al₂O₃ (DP) showed excellent sulfur tolerance while its initial activity decreased. It was observed that with the chlorine bridge, the interfacial structure of Pd-Cl⁻¹-Ce³⁺ was responsible for the high activity of the Pd-CeO₂/Al₂O₃ (IM) catalyst, at the same time the interaction of Pd with Ce was weakened by Cl₋₁ ions. The enhanced sulfur tolerance over the Pd-CeO₂/Al₂O₃ (IM) catalyst was attributed to the weakened Pd-S bond caused by the competitive adsorption of H₂S on Ce³⁺ ions. As to the Pd-CeO₂/Al₂O₃ (DP) catalyst, a strong interaction of Pd with Ce put Pd at an electron-deficient state, the creation of sulfided palladium was therefore inhibited.     

Catalytic properties of PdCu/Al2O3 system obtained via anchored metal complexes

The TON of PdCu/Al₂O₃ is two orders of magnitude lower in ethane hydrogenolysis and several times lower in vinylacetylene and CO hydrogenation as compared to that of a Pd/Al₂O₃ catalyst. Nonadditivity of the catalytic properties indicates the formation of bimetallic particles, whose thermal stability is lower than that of the monometallic one.     

Selective hydrogenation of phenylacetylene on Pd/Al2O3: Effect of the addition of Pt and particle size

Phenylacetylene hydrogenation on Pd, Pt and Pd–Pt/Al₂O₃ catalysts has been studied. In all catalysts activity was found not to depend on particle size. However, selectivity to styrene was found to depend on Pd/Al₂O₃ catalysts. Carbon deposition in both metal and support explains such a behavior. Nevertheless, in small Pd particles a longer residence time of styrene may control the selectivity.     

过渡金属修饰Fe2O3/Al2O3氧载体的Redox性能研究

采用冷冻干燥法分别制备了经Cu、Co、Mn、Ni修饰的Fe₂O₃/Al₂O₃氧载体。利用化学吸附仪,通过程序升温还原(H₂-TPR)和程序升温氧化(TPO)来研究经不同过渡金属修饰的Fe₂O₃/Al₂O₃与H₂和O₂的反应性能。实验发现,在Fe₂O₃/Al₂O₃中加入Cu、Co、Ni以后,氧载体与H₂的反应性都有提高,但是当在Fe₂O₃/Al₂O₃中加入Mn以后,氧载体的反应性和载氧能力反而下降。经Cu修饰的Fe₂O₃/Al₂O₃与H₂的反应性最高,且具有很好的反应稳定性,适合用于化学链燃烧。     

Combination of CO2 reforming and partial oxidation of CH4 over Ni/Al2O3 catalysts using fluidized bed reactor

The effects of the Ni loading, total feed flow rate, prereduction temperature, reaction temperature and feed gas ratio for combination of CO₂ reforming and partial oxidation of CH₄ over Ni/Al₂O₃ were investigated using a fluidized bed reactor. Methane conversion to syngas was drastically enhanced using a fluidized bed reactor over Ni/Al₂O₃ catalyst calcined at high temperature. The fluidized bed and the fixed bed reactor were compared and a promoting mechanism of the fluidized bed reactor was proposed. This revised version was published online in August 2006 with corrections to the Cover Date.     

Methane Combustion over Pd/Al2O3 Catalyst: Effects of Chlorine Ions and Water on Catalytic Activity

The influences of residual chlorine ions and water on the performance of a Pd/Al₂O₃ catalyst in methane combustion have been studied. The results show that the catalyst containing Cl⁻ exhibits a relatively low activity, and the addition of water to the reaction system accelerates the deactivation process. The catalyst has been characterized by N₂ adsorption, X-ray fluorescence, Fourier transform infrared spectroscopy (FT-IR), and thermogravimetry (TG). The results show that the presence of Cl⁻ appears to strongly inhibit the total oxidation of methane and hinder the dispersion of Pd on Al₂O₃. The formation of Pd(OH)₂ during the reaction is the most likely reason for the inhibition effect of water, which is confirmed by FT-IR and TG analysis. The regeneration of the Pd/Al₂O₃ catalyst can be achieved by purging in nitrogen at 550 °C.     

Alkylation of phenol with dimethyl carbonate over AlPO4, Al2O3 and AlPO4-Al2O3 catalysts

The vapor-phase catalytic alkylation of phenol with dimethyl carbonate over different AlPO₄ (Al/P=1), Al₂O₃ and AlPO₄-Al₂O₃ (5–25 wt.% Al₂O₃) catalysts produces anisole (O-alkylation) as the major reaction product althougho-cresol (C-alkylation) and methylanisoles were also found. The reaction is first order in phenol while O-and C-alkylation follow parallel processes. As compared with methanol, DMC is far more effective as a methylating agent, and the methylation proceeds at a lower temperature and with higher O-alkylation selectivity.