Transmission electron microscopy observations of CNT morphology before and after heating in vacuum

Heating of multi-walled carbon nanotubes is often required to obtain clean patterns in the field electron emission microscope (FEEM). A transmission electron micrograph study of morphological changes in the cap structure of multi-walled carbon nanotubes due to heating in vacuum is presented. The lack of significant structural change in the cap structure when specimens were heated to 1925 K for 2.5 h determines an upper bound for the diffusivity of multi-walled carbon nanotube surface atoms, of the order of 10⁻¹⁶ cm²/s at 1925 K.     

Controllable synthesis and modification of carbon micro-spheres from deoiled asphalt

A series of size-controllable carbon micro-spheres (CMSs) were synthesized from deoiled asphalt by chemical vapour deposition, with the emphasis on the effect of reaction temperature, Ar flow rate and collection zone. Graphitized carbon micro-spheres (GCMSs) were obtained from as-prepared CMSs by vacuum heat treatment at 2000 °C for 1 h. Air oxidation was performed to realize functionalization of CMSs. Morphologies and structures of CMSs and GCMSs were characterized by field emission scanning electron microscopy, high-resolution transmission electron microscopy, energy dispersive X-ray spectroscopy, X-ray diffraction and Raman spectroscopy, and the functional groups on the surface of GCMSs and CMSs were characterized by Fourier transformation infra-red spectrometry. Results show that effective mass production of size-controllable CMSs, with diameters ranging from 100 nm to 1 μm, was achieved. As-obtained high purity CMSs were spherical with uniform size and low graphitization degree, but the graphitization degree of GCMSs was enhanced obviously. By air oxidation, some oxygen-containing functional groups were introduced onto the surface of CMSs, while no functional groups were introduced onto the surface of GCMSs.     

Characterization of structural modifications in poly-tetra-fluoroethylene induced by electron beam irradiation

The effects of electron beam irradiation doses on the poly-tetra-fluoroethylene (PTFE) have been studied. Several techniques, such as X-ray diffraction (XRD), differential scanning calorimetry (DSC), mechanical properties and Fourier transform infrared spectroscopy (FTIR) were applied to characterize the PTFE samples and to study the radiation effects on the crystal structure of the polymer.The irradiation dose up to 150 kGy showed an increase in the crystallinity degree of PTFE, which has been observed and confirmed during the DSC and XRD measurements. The increase in crystallinity was attributed to the scissions of the chain in the amorphous region. Moreover, the number-average molecular weights were estimated from the heat of crystallization measured by DSC technique. The results indicated that the molecular weights were decreased by increasing the heat of crystallization due to irradiation with doses up to 150 kGy. Radiation resistance of the irradiated and non-irradiated PTFE was investigated during its mechanical properties at room temperature. The dose at half value of the elongation at break is about 3.10 kGy while the dose at half value of the tensile strength is about 1.70 kGy.     

Comparative study of electrochemical capacitance of multi-walled carbon nanotubes before and after chopping

In the work, short multi-walled carbon nanotubes (S-CNTs) were synthesized by chopping conventional μm-long multi-walled carbon nanotubes (L-CNTs) under ultrasonication in H₂SO₄/HNO₃ mixed acids. A comparative electrochemical investigation performed in 6 M KOH solution demonstrated that a specific capacitance (SC) of ca. 14.6 μF cm⁻² was delivered by the S-CNTs with the specific surface area (SSA) of 207 m² g⁻¹, much larger than that of ca. 10.1 μF cm⁻² for the L-CNTs with the SSA of 223 m² g⁻¹, the reason for which was that S-CNTs with two open ends, due to good ion penetrability, provided more entrances for electrolyte ions to access the inner surface easily through their shorter inner pathway so as to enhance their SSA utilization and geometric SC. The surface structure disruption of S-CNTs, owing to ultrasonication and oxidation during chopping process, deteriorated their electronic conductivity and resulted in an inferior power property in contrast to L-CNTs.     

Origin of ohmic behavior in Ni, Ni2Si and Pd contacts on n-type SiC

Ni, Ni₂Si and Pd contacts were prepared on n-type 4H-SiC and annealed in the temperature range of 750-1150 °C. The annealed contacts were analyzed before and after acid etching, and different features were found in unetched and etched contacts. Carbon left on the SiC surface after the acid etching of Ni₂Si contacts annealed at 960 °C was highly graphitized. In nickel contacts, the graphitization of interface carbon began at 960 °C and increased after annealing at higher temperatures. In palladium contacts, the onset of the interface carbon graphitization was observed after annealing at 1150 °C. For all three types of metallization, the minimal values of contact resistivity were achieved only when the sharp first-order peak at 1585 cm⁻¹ and distinct second-order peak at ∼2700 cm⁻¹ related to the presence of graphitized carbon were detected by Raman spectroscopy after the acid etching of contacts. The properties of unannealed secondary contacts deposited onto etched primary contacts were similar to the properties of the primary contacts unless carbon was selectively etched. The results show that ohmic behavior of Ni-based and Pd contacts on n-type SiC originates from the formation of graphitic carbon at the interface with SiC.     

Electron beam initiated grafting of methacryloxypropyl-trimethoxysilane to fused silica glass

The effect of electron beam pretreatment of fused silica glass upon its surface functional composition and possibility for subsequent immobilization of methacryloxypropyl-trimethoxysilane (MOPTMS) layer is studied using FTIR spectroscopy and adsorption of acid-base indicators. The content of Brensted acidic centers (silanol groups) on the irradiated fused silica surface is found to follow an “oscillatory” trend as function of the absorbed dose below 100 kGy at electron beam processing due to the alternating reactions of hydroxylation (probably as a result of Si-O-Si bond disruption and interaction with radiolyzed physically adsorbed water) and thermal dehydration/dehydroxylation at radiation heating. The best conditions for MOPTMS layer formation are based on the increased acidity of both silica surface (formation of acidic hydroxyls) and the reaction medium (MOPTMS deposition from acetic acid solution). The optimal value of absorbed dose at electron beam processing providing the highest efficiency of MOPTMS grafting is 50 kGy at accelerated electron energy 700 keV. Electron beam pretreatment of fused silica surface is shown to provide more efficient MOPTMS immobilization in comparison with conventional chemical and thermal grafting procedures. The obtained results are promising for the enhancement of the processes for the production of fused silica glass capillaries for electrochromatography and electrophoresis at the stage of an intermediate bifunctional layer formation required for the subsequent deposition of specific polymer coatings.     

Morphology, mechanical, cross-linking, thermal, and tribological properties of nitrile and hydrogenated nitrile rubber/multi-walled carbon nanotubes composites prepared by melt compounding: The effect of acrylonitrile content and hydrogenation

The purpose of this work was to prepare nanocomposites by mixing multi-walled carbon nanotubes (MWCNT) with nitrile and hydrogenated nitrile elastomers (NBR and HNBR). Utilization of transmission electronic microscopy (TEM), scanning electron microscopy (SEM), and small- and wide-angle X-ray scattering techniques (SAXS and WAXS) for advanced morphology observation of conducting filler-reinforced nitrile and hydrogenated nitrile rubber composites is reported. Principal results were increases in hardness (maximally 97 Shore, type A), elastic modulus (maximally 981 MPa), tensile strength (maximally 27.7 MPa), elongation at break (maximally 216%), cross-link density (maximally 7.94 × 10²⁸ m⁻³), density (maximally 1.16 g cm⁻³), and tear strength (11.2 kN m⁻¹), which were clearly visible at particular acrylonitrile contents both for unhydrogenated and hydrogenated polymers due to enhanced distribution of carbon nanotubes (CNT) and their aggregated particles in the applied rubber matrix. Conclusion was that multi-walled carbon nanotubes improved the performance of nitrile and hydrogenated nitrile rubber nanocomposites prepared by melt compounding.     

Synthesis of carbon nanotubes by CVD: Effect of acetylene pressure on nanotubes characteristics

The effect of acetylene partial pressure on the structural and morphological properties of multi-walled carbon nanotubes (MWCNTs) synthesized by CVD on iron nanoparticles dispersed in a SiO₂ matrix as catalyst was investigated. The general growing conditions were: 110 cm³/min flow rate, 690 °C synthesis temperature, 180 Torr over pressure and two gas compositions: 2.5% and 10% C₂H₂/N₂. The catalyst and nanotubes were characterized by HR-TEM, SEM and DRX. TGA and DTA were also carried out to study degradation stages of synthesized CNTs. MWCNTs synthesized with low acetylene concentration are more regular and with a lower amount of amorphous carbon than those synthesized with a high concentration. During the synthesis of CNTs, amorphous carbon nanoparticles nucleate on the external wall of the nanotubes. At high acetylene concentration carbon nanoparticles grow, covering all CNTs’ surface, forming a compact coating. The combination of CNTs with this coating of amorphous carbon nanoparticles lead to a material with high decomposition temperature.     

Electron beam induced modification of poly(ethylene terephthalate) films

Electron beam processing of poly(ethylene terephthalate) (PET) films is found to promote significant changes in the melting heat, intrinsic viscosity and polymer film-liquid (water, isooctane and toluene) boundary surface tension. These properties are featured with several maximums depending on the absorbed dose and correlating with the modification of PET surface functionality. Studies using adsorption of acid-base indicators and IR-spectroscopy revealed that the increase of PET surface hydrophilicity is determined by the oxidation of methylene and methyne groups. Electron beam treatment of PET films on the surface of N-vinylpyrrolidone aqueous solution provided graft copolymerization with this comonomer at optimum process parameters (energy 700 keV, current 1 mA, absorbed dose 50 kGy).     

Inter-collisional cutting of multi-walled carbon nanotubes by high-speed agitation

High-speed agitation by a mixing blade has efficiently achieved the cutting of a large diameter (100-150 nm) of multi-walled carbon nanotubes. The cutting process is caused by an inter-collision of the nanotubes with high transfer energy. The collision-induced cutting allows for the shortening of the nanotubes without serious damage of the original graphitic layers due to the cutting effect being limited to the collision points. Furthermore, the operation under ambient atmosphere introduces oxygen-containing functional groups to the cut nanotubes. The estimated length distribution has indicated that high-speed agitation achieves a large cutting effect during a short duration of several minutes.     

Structure evolution from nanocolumns to nanoporous of nitrogen doped amorphous carbon films deposited by magnetron sputtering

Different nitrogen doped amorphous carbon (CNx) films were obtained by magnetron sputtering of carbon target in argon and nitrogen atmosphere at the increasing negative bias voltages from 0 to 150 V. The films structures have experienced great change, from the novel column to nanoporous structure at the bias voltage of 0 V to the porous structure at 150 V. The proposed growth process was that the CNx nuclei grew at 0 V acted as the “seeds” for the growth of the nanocolumns, and ion etching effects at 150 V induced the formation of nanoporous structures. Furthermore, a comparison study showed that the field emission properties of the CNx films were related with the introduction of the nitrogen atoms, the size and concentration of sp² C clusters and the surface roughness. The films with rougher surface have lower threshold field.     

Surface chemistry and catalytic activity of Ni/Al2O3 irradiated with high-energy electron beam

The radiation effects induced effects by electron beam (EB) treatment on the catalytic activity of Ni/γ-Al₂O₃ were studied for the carbon dioxide reforming of methane with different EB energy and absorbed radiation dose. Transmission electron microscope (TEM), X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) were used to determine the change in structure and surface states of Ni/γ-Al₂O₃ catalyst before and after the EB treatment. Higher energy EB treatment is useful for increasing the proportion of the active sites (such as Ni⁰ and NiAl₂O₄-phase) on the surface. The increase of Ni/Al-ratio indicates that the Ni dispersion on the surface increased with the EB-treatment, resulting in an increase of the active sites, which leads to improving the catalytic activity. XPS measurement also showed a decrease of the surface carbon with EB dose. The maximum 20% increase in the conversion of CO₂/CH₄-mixture into CO/H₂ gas was observed for the catalyst treated with 2 MeV energy and 600 kGy dose of EB relative to untreated.     

Carbon nanotubes as reinforcement of styrene-butadiene rubber

This study reports an easy technique to produce cured styrene-butadiene rubber (SBR)/multi-walled carbon nanotubes (MWCNT) composites with a sulphur/accelerator system at 150 °C. Significant improvement in Young's modulus and tensile strength were achieved by incorporating 0.66 wt% of filler without sacrificing SBR elastomer high elongation at break. A comparison with carbon black filled SBR was also made. Field emission scanning electron microscopy was used to investigate dispersion and fracture surfaces. Results indicated that the homogeneous dispersion of MWCNT throughout SBR matrix and strong interfacial adhesion between oxidized MWCNT and the matrix are responsible for the considerable enhancement of mechanical properties of the composite.     

Effects on the field emission properties by variation in surface morphology of patterned photosensitive carbon nanotube paste using organic solvent

Photosensitive carbon nanotube (CNT) paste was prepared by 3-roll milling of multi-walled carbon nanotubes (MWNTs), UV-sensitive binder solution, and Ag as filler additives. Arrays of MWNT dots with a diode structure were fabricated by a combination of screen printing method and photolithography using these paste, and acetone utilized as the developer. The MWNT dots were well-defined and the organic binder materials in the dots were partially removed. The MWNT film without a heat treatment showed a high current density of 1.35 mA/cm² at 3.25 V/μm and low turn-on field of 2.2 V/μm at 100 μA/cm². Acetone can be used as an efficient developer to form patterns and to remove the organic residues in patterns, simultaneously.     

High-field electron emission of carbon nanotubes grown on carbon fibers

Carbon nanotubes with uniform density were synthesized on carbon fiber substrate by the floating catalyst method. The morphology and microstructure were characterized by scanning electron microscopy and Raman spectroscopy. The results of field emission showed that the emission current density of carbon nanotubes/carbon fibers was 10 μA/cm² and 1 mA/cm² at the field of 1.25 and 2.25 V/μm, respectively, and the emission current density could be 10 and 81.2 mA/cm² with the field of 4.5 and 7 V/μm, respectively. Using uniform and sparse density distribution of carbon nanotubes on carbon fiber substrate, the tip predominance of carbon nanotubes can be exerted, and simultaneously the effect of screening between adjacent carbon nanotubes on field emission performance can also be effectively decreased. Therefore, the carbon nanotubes/carbon fibers composite should be a good candidate for a cold cathode material.     

Oxygen contaminants affecting on the electronic structures of the carbon nano tubes grown by rapid thermal chemical vapor deposition

Oxygen-related electronic structures of CNTs (carbon nanotubes) grown by rapid thermal chemical vapor deposition (RT-CVD) have been investigated by using partial electron yield near edge X-ray absorption spectroscopy (PEY-NEXAFS) and X-ray photoelectron spectroscopy (XPS). On the CNT surface with increased oxygen resulting from e-beam irradiation under the O₂ gas environment, C k-edge NEXAFS spectra showed an increase of the oxygen-related resonance peaks ranging from 287 to 289 eV whereas the sp² related peak at 285.4 eV was nearly unchanged. After the complete removal process of the oxygen atom on the surface by annealing the sample at 500 °C for 30 min, C K-edge spectra showed an abrupt decrease of the oxygen-related resonance peaks in 287-289 eV and an increase of the sp² related peak at 285.4 eV, indicating that the degree of crystallinity in the CNT sample was improved.     

Sonochemical growth of antimony selenoiodide in multiwalled carbon nanotube

This paper presents, for the first time, the nanocrystalline, semiconducting antimony selenoiodide (SbSeI) grown in multi-walled carbon nanotubes (CNTs). It was prepared sonochemically using elemental Sb, Se, and I in the presence of ethanol under ultrasonic irradiation (35 kHz, 2.6 W/cm²) at 323 K for 3 h. The CNTs filled with SbSeI were characterized by using techniques such as powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray analysis, high-resolution transmission electron microscopy, selected area electron diffraction, and optical diffuse reflection spectroscopy. These investigations exhibit that the SbSeI filling the CNTs is single crystalline in nature and in the form of nanowires. It has indirect allowed energy band gap E_gIf = 1.61(6) eV.     

Flame synthesis of carbon nanotubes for panel field emission lamp

Multi-walled carbon nanotubes (CNTs) were synthesized on the surfaces of Ni-alloy plated Fe-wires with the diameter of 2 mm using a conventional laboratory ethanol (C₂H₅OH) flame method at 560 °C. SEM showed that the product had bush-shaped micron-structures with diameters from 100 to 450 nm and lengths of over 1.0 μm. TEM revealed that the micron-structures were composed of multi-walled nanotube bundles with the diameters of about 50 nm. The test on the diode configuration field emission of the Fe-wire arrays was performed. The onset electric field was 2.95 V/μm and the emission current can reach 50 mA/cm² at an electric field of 9 V/μm. The average fluctuation of the emission current density was less than 7%. The result suggests that the field emission was uniform and the present technique was feasible to fabricate Panel Field Emission Lamp (PFEL) with arrays of carbon nanotubes. PFEL has the advantages of high luminescence as well as stability, and thus, it can be used to replace ordinary lights.     

Multiwalled carbon nanotubes effect on the bioavailability of artemisinin and its cytotoxity to cancerous cells

Artemisinin regarded as one of the most promising anticancer drugs can bind to DNA with a binding constant of 1.04 × 10⁴ M⁻¹. The electrochemical experiments indicated that for longer incubation time periods, the reduction peak current of artemisinin on carbon nanotube modified electrode increases. Therefore, the uptake of drug molecules from a solution into CNTs will be achieved automatically by adsorption of 88.7% of artemisinin onto carbon nanotubes surface without alteration in drug properties. Hence, capability of carbon nanotubes to have synergistic effect on the bioavailability of artemisinin was investigated. Experimental tests on K562 cancer cell lines growth by MTT assay proved that multi-walled carbon nanotubes can enhance the cytotoxity of artemisinin to the targeted cancer cells with unprecedented accuracy and efficiency. The IC₅₀ values were 65 and 35 μM for artemisinin and artemisinin loaded on multi-walled carbon nanotubes, respectively; demonstrating that artemisinin loaded on multi-walled carbon nanotubes is more effective in inhibition of cancer cell lines growth.     

Influence of growth time on field emission properties from carbon nanotubes deposited on arrayed nanoporous silicon pillars

We investigated the influence of growth time on field emission properties of multi-walled carbon nanotubes deposited on silicon nanoporous pillar array (MWCNTs/Si-NPA), which were fabricated by thermal chemical vapour deposition at 800 °C for 5, 15 and 25 min respectively, to better understand the origins of good field emission properties. The results showed that the MWCNTs/Si-NPA grown for 15 min had the highest field emission efficiency of the three types of samples. Morphologies of the products were examined by field-emission scanning electron microscope, and the excellent field emission performance was attributed not only to the formation of a nest array of multi-walled carbon nanotubes, which would largely reduce the electrostatic shielding among the emitters and resulted in a great enhancement factor, but also to the medium MWCNTs density films, there was an ideal compromise between the emitter density and the intertube distance, which also could effectively avoid electrostatic shielding effects, along with a high emitter density.