Effect of vacuum heat treatment on tensile strength and fracture performance of cold-sprayed Cu-4Cr-2Nb coatings

The previous study [1] indicated that dense thick Cu-4Cr-2Nb coatings could be formed by cold spraying, and the post-spray heat treatment could significantly influence the microstructure and microhardness of the as-sprayed Cu-4Cr-2Nb coatings. In this study, the tensile strength and fracture performance of the Cu-4Cr-2Nb coatings after annealing were investigated. The vacuum heat treatment was conducted under 10⁻² Pa at 850 °C for 4 h. Results showed that the heat treatment had a great contribution to the healing-up of the incompleteness of the interfaces between the deposited particles. In addition, the coating microhardness decreased from 156.8 ± 4.6 Hv_0.2 for the as-sprayed coatings to 101.7 ± 4.5 Hv_0.2 for the annealed ones. The mean tensile strength of the annealed coatings was approximately 294.1 ± 36.1 MPa compared to that of 45.0 ± 10.5 MPa for the as-sprayed ones, which results from the partially metallurgically bonded zones between the deposited particles inducing by the heat treatment process.     

Characteristics and heat treatment of cold-sprayed Al-Sn binary alloy coatings

In this study, Al-Sn binary alloy coatings were prepared with Al-5 wt.% Sn (Al-5Sn) and Al-10 wt.% Sn (Al-10Sn) gas atomized powders by low pressure and high pressure cold spray process. The microstructure and microhardness of the coatings were characterized. To understand the coarsening of tin in the coating, the as-sprayed coatings were annealed at 150, 200, 250 and 300 °C for 1 h, respectively. The effect of annealing on microstructure and the bond strength of the coatings were investigated. The results show that Al-5Sn coating can be deposited by high pressure cold spray with nitrogen while Al-10Sn can only be deposited by low pressure cold spray with helium gas. Both Al-5Sn and Al-10Sn coatings present dense structures. The fraction of Sn in as-sprayed coatings is consistent with that in feed stock powders. The coarsening and/or migration of Sn phase in the coatings were observed when the annealing temperature exceeds 200 °C. Furthermore, the microhardness of the coatings decreased significantly at the annealing temperature of 250 °C. EDXA analysis shows that the heat treatment has no significant effect on fraction of Sn phase in Al-5Sn coatings. Bonding strength of as-sprayed Al-10Sn coating is slightly higher than that of Al-5Sn coating. Annealing at 200 °C can increase the bonding strength of Al-5Sn coatings.     

Effect of heat treatment on the microstructure and microhardness of cold-sprayed tin bronze coating

Tin bronze (TB) powder was deposited on a stainless steel substrate by cold spraying. Post-deposition heat treatment was conducted in an electrical resistance furnace under nitrogen atmosphere at a temperature of 850 °C for 3 h. The effect of heat treatment on the microstructure and microhardness of cold-sprayed TB coating was investigated. It was found that the as-sprayed TB coating presented a dense microstructure. Heat treatment significantly influenced the microstructure and microhardness of cold-sprayed TB coating. A distinguishable diffusion layer of about 150 μm was formed in the coating near the coating/substrate interface. A compound was precipitated in the diffusion layer. The microhardness in the coating was changed gradually along the coating from the interface to the coating surface after heat treatment. The microhardness in the diffusion layer was high owing to the precipitation of hard phase, while it was much low in other area due to the obvious grain growth during annealing.     

Microstructure, microhardness and dry friction behavior of cold-sprayed tin bronze coatings

In this paper, two types of tin bronze coatings (Cu-6 wt.% Sn and Cu-8 wt.% Sn) were prepared by cold spray process. The as-sprayed coatings were subjected to a vacuum heat treatment at 600 °C for 3 h. The coating microstructure, microhardness and tribological performance were characterized. The effects of the tin content and the vacuum heat treatment on the microstructure, microhardness and tribological behavior of the coatings were investigated. It is found that the as-sprayed CuSn6 (As6) and CuSn8 (As8) coatings exhibit practically an identical porosity. Meanwhile, As8 presents a higher microhardness than As6. In addition, the increase of the tin content in the powder feedstock leads to a lower wear rate. After a heat treatment, coating porosities are significantly reduced. However, the coating hardness is significantly decreased and the coating presents a much decreased wear resistance. For the as-sprayed coatings, such factors as ploughing and particle delamination could determine the sliding process. The heat treatment results in a distinct modification of the tribological behavior. For the annealed coatings, the adhesion, between the coating and the counterpart, could play a dominant role in the sliding process.     

Abrasive resistance of arc sprayed carbonitride alloying self-shielded coatings

Wear-resistant coatings were prepared on the surface of the Q235 low-carbon steel plate by HVAS with the carbonitride alloying self-shielded flux-cored wire. Detection and analysis on the microstructure and properties of the coatings were carried out by using scanning electron microscope, microhardness tester and wear tester. The forming, the wear resistance and its mechanism of the coatings were studied. The results show that the coatings have good forming, homogeneous microstructure and compact structure. The coatings have good hardness, the average microhardness value reaches 520 HV_0.1, and the highest value is up to about 560 HV_0.1. As a result, the coatings have good abrasive wear performance and adhesion strength.     

Effect of Ni-to-Fe ratio on structure and properties of Ni-Fe-B-Si-Nb coatings fabricated by laser processing

Ni-Fe-B-Si-Nb coatings have been deposited on mild steel substrates using high power laser cladding process followed by laser remelting. The influence of Ni-to-Fe concentration ratio in (Ni_100−xFe_x)₆₂B₁₈Si₁₈Nb₂ (x = 55, 50, 45 and 40) powders on the phase composition and microstructure is analyzed by X-ray diffraction, scanning- and transmission-electron microscopies. The microhardness and corrosion resistance properties of the coatings are also measured. The results reveal that amorphous matrix layers are obtained for all coatings. The increase of the Ni-to-Fe ratio can promote the formation of γ(Fe-Ni) phase and decrease the formation of Fe₂B phase and α-Fe phase. The coating with 1:1 ratio of Ni-to-Fe exhibits the highest microhardness of 1200 HV_0.5 and superior corrosion resistance property due to its largest volume fraction of amorphous phase in the coating. Higher or lower than 1:1 ratio of Ni-to-Fe may result in lower amorphous forming ability. However, even that the coating with ratio of 3:2, shows a minimum of microhardness, it shows a better corrosion resistance than other two coatings.     

Wear resistance of reactive plasma sprayed and laser remelted TiB2-TiC0.3N0.7 based composite coatings against medium carbon steel

Wear resistance of reactive plasma sprayed TiB₂-TiC_0.3N_0.7 based composite coatings and the as-sprayed coating with laser surface treatment was investigated using plate-on-plate tests. Wear tests were performed at different normal loads and sliding speeds under dry sliding conditions in air. The surface morphologies of counterparts against as-sprayed and laser remelted coatings were investigated. The microstructure and chemical composition of wear debris and coatings were studied using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDS), respectively. The results show that the wear resistance of the laser remelted coating is improved significantly due to their increased microhardness and reduced flaws. The primary wear mechanism of the remelted coating is oxidation wear and its minor wear mechanisms are grain abrasion and fatigue failure during the course of wear test. In contrast, the primary wear mechanism of the as-sprayed coating is grain abrasion at the low sliding speed (370 rpm) and fatigue failure at the high sliding speed (549 rpm). The oxidation wear mechanism is a minor contributor for the as-sprayed coating.     

Microstructure and properties of TiC-Fe36Ni cermet coatings by reactive plasma spraying using sucrose as carbonaceous precursor

This study is aimed to introduce an innovative precursor pyrolysis process to prepare Ti-Fe-Ni-C compound powder and to discuss and evaluate the relationship between microstructure and properties of TiC-Fe36Ni cermet coatings in-situ synthesized by reactive plasma spraying (RPS) of these compound powders. The main characteristic of the pyrolysis process is that sucrose (C12H22O11) is used as a source of carbon as well as a binder to bind reactive constituent particles. The compound powder with high bonding strength can avoid the problem that reactive constituent particles are separated during spraying. The TiC-Fe36Ni cermet coatings present typical splat-like morphology of thermally sprayed coatings and consist of two different areas: one is a composite reinforcement area where spherical fine TiC particles (100-500 nm) homogeneously distribute within the Fe36Ni matrix; the other is an area of TiC accumulation. The surface hardness of the coatings reaches about 90 ± 2 (HR15N). The maximum and average microhardness values of the coatings are 1930 HV_0.2 (Vicker Hardness) and 1640 HV_0.2, respectively. The average bonding strength of the coatings is about 62.3 MPa. The wear resistance property of the coatings is much more than that of Ni60 alloys coatings.     

Influence of treating frequency on microstructure and properties of Al2O3 coating on 304 stainless steel by cathodic plasma electrolytic deposition

Alumina ceramic coatings were fabricated on 304 stainless steel by cathodic plasma electrolytic deposition (CPED). Influence of treating frequency of the power supply on the microstructure and properties of the coatings were studied. The results indicated that coatings obtained at various frequencies on 304 stainless steels were all composed of α-Al₂O₃ and γ-Al₂O₃, and α-Al₂O₃ was the dominant phase. The contents of α-Al₂O₃ decreased gradually in a very small rate with increasing the frequency and γ-Al₂O₃ gradually increased. The surface of alumina ceramic coating was porous. With increasing the frequency, the coating surface gradually became less rough and more compact, resulting in low surface roughness. The bonding strength of Al₂O₃ coating was higher than 22 MPa and was not strongly affected by treating frequency. With increasing the frequency, the alumina coated steels showed better and gradually increasing corrosion resistance than the uncoated one in 3.5% NaCl solution. The coating steel with desirable corrosion resistance was obtained at 800 Hz whose corrosion current potential and corrosion density were −0.237 V and 7.367 × 10⁻⁸ A/cm², respectively.     

Synthesis and microstructure observation of titanium carbonitride nanostructured coatings using reactive plasma spraying in atmosphere

In the present study, nanostructured titanium carbonitride (TiCN) coatings were successfully deposited by reactive plasma spraying (RPS) technology using a self-designed gas tunnel mounted on a normal plasma spray torch. The phase composition and microstructure of the TiCN coatings were characterised by XRD, SEM and TEM. The results indicated that the main phase of the coatings was FCC TiC_0.2N_0.8 with a small amount of Ti₃O. The coating that was deposited using 35 kW displayed better microstructure and properties. The coating exhibited a typical nanostructure including 90 nm diamertrical equiaxed grains and 400 nm long columnar grains by TEM images. The SEM observation further revealed that the equiaxed grains in parallel direction to the substrate surface in TEM images were actually the columnar grains perpendicular to the substrate surface. The formation mechanism of the nanostructured coatings was also discussed. The measured microhardness value of the coating was approximately 1659 Hv_100 g, and the calculated crack extension force was about 34.9 J/m².     

High performance nanostructured ZrO2 based thermal barrier coatings deposited by high efficiency supersonic plasma spraying

In this paper, the nanostructured zirconia (ZrO₂) based thermal barrier coatings (TBCs) deposited by high efficiency supersonic atmospheric plasma spraying (SAPS), were described. The phase composition, microstructure, thermal conductivity and thermal shock resistance of as-sprayed coating were studied. The results revealed that the as-sprayed coating was composed of tetragonal zirconia and consisted of some unmelted nanoparticles (30-50 nm) and nanograins (60-110 nm), and the latter was the main microstructure of the coating. The nanograins and homogeneously distributed micro-cracks of coating resulted in not only low thermal conductivity, but also high thermal cycling lives. Besides, the failure process of coating during thermal cycles was also investigated in the present work.     

Effect of NaAlO2 concentrations on microstructure and corrosion resistance of Al2O3/ZrO2 coatings formed on zirconium by micro-arc oxidation

In this study, Al₂O₃/ZrO₂ composite coatings were prepared on Zr substrates by micro-arc oxidation (MAO) in the NaAlO₂-containing electrolytes, and the effect of NaAlO₂ concentration on the microstructure, bond strength, microhardness and corrosion resistance of coatings was systematically investigated. The study reveals that the adequate NaAlO₂ in the electrolyte (>0.2 M) is essential to the formation of needle-like α-Al₂O₃ in the coatings, and the amount of α-Al₂O₃ rises with the increase of the NaAlO₂ concentration. m-ZrO₂ and t-ZrO₂ are present in all of the coatings, but their relative amount largely depends on the amount of Al₂O₃. It is also found that as the NaAlO₂ concentration increases from 0.2 to 0.3 M, the coating becomes denser and thicker, and its bond strength, maximum microhardness and corrosion resistance increases as well. The coating formed at 0.3 M NaAlO₂ demonstrates the highest bond strength of 52 MPa, the maximum microhardness of 1600 Hv_0.2N and the superior corrosion resistance. However, the overhigh concentration of NaAlO₂ (0.35 M) is found harmful to the coating's microstructure and properties.     

Influence of high temperature annealing on the structure, hardness and tribological properties of diamond-like carbon and TiAlSiCN nanocomposite coatings

Diamond-like carbon (DLC) and TiAlSiCN nanocomposite coatings were synthesized and annealed at different temperatures in a vacuum environment. The microstructure, hardness and tribological properties of as-deposited and annealed DLC-TiAlSiCN nanocomposite coatings were characterized by X-ray diffraction, X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), Raman spectroscopy, nano-indentation and friction tests. The TEM results reveal that the as-deposited DLC-TiAlSiCN coating has a unique nanocomposite structure consisting of TiCN nanocrystals embedded in an amorphous matrix consisting of a-Si₃N₄, a-SiC, a-CN and DLC, and the structure changed little after annealing at 800 °C. However, XPS and Raman results show that an obvious graphitization of the DLC phase occurred during the annealing process and it worsened with annealing temperature. Because of the graphitization, the hardness of the DLC-TiAlSiCN coating after annealing at 800 °C decreased from 45 to 36 GPa. In addition, the DLC-TiAlSiCN coating after annealing at 800 °C has a similar friction coefficient to the as-deposited coating.     

Measurement of the magnetic moment in a cold worked 304 stainless steel using HTS SQUID

The magnetic properties of stainless steel have been investigated using a radio frequency (RF) high-temperature superconductivity (HTS) SQUID (Superconducting QUantum Interference Device)-based susceptometer. The nuclear grade 304 stainless steel is nonmagnetic at a normal condition but it changes to a partially ferromagnetic state associated with martensitic transformation under a plastic deformation. The magnetic moment of the 304 stainless steels was increased with an increasing cold work rate, and decreased with an increasing annealing temperature. The change of mechanical properties such as yield strength and ultimate tensile strength (UTS) are also analyzed in terms of deformation-induced martensitic transformation.     

Surface laser alloying of 17-4PH stainless steel steam turbine blades

As a known high-quality precipitation hardening stainless steel with high strength, high antifatigue, excellent corrosion resistance and good weldability, 17-4PH has been widely used to produce steam turbine blades. However, under the impact of high-speed steam and water droplets, the blades are prone to cavitation, which could lead to lower efficiency, shorter life time, and even accidents. In this article, the 17-4PH blade's surface was alloyed using a high power CO₂ laser. The microstructure and microhardness of hardened 17-4PH were tested by scanning electronic microscope (SEM), X-ray diffraction (XRD), energy disperse spectroscopy (EDS) and a microhardness tester. After laser alloying, the surface layer was denser and the grain refined, while the microhardness of the surface (average 610HV_0.2) was about one times higher than that of the substrate material (330HV_0.2). The friction coefficient of the laser-alloyed 17-4PH layer was much lower than that of the substrate.     

Microstructure, bonding strength and thermal shock resistance of ceramic coatings on steels prepared by plasma electrolytic oxidation

Ceramic coatings were successfully prepared on steel by plasma electrolytic oxidation (PEO) in aluminate electrolyte and silicate electrolyte, respectively. The microstructure of the coatings including surface morphology, phase and element composition were studied by scanning electron microscopy (SEM) and X-ray diffraction (XRD), respectively. The bonding strength between the ceramic coating and the substrate was tested using different methods including tensile tests and shearing tests. The thermal shock resistance of the coatings was also evaluated. The results indicated that coatings obtained in both electrolytes were porous and coarse. The average diameters of the pores were below 10 μm. PEO coatings obtained in aluminate electrolyte were composed of Fe₃O₄ and FeAl₂O₄, while those obtained in silicate electrolyte were in a noncrystal state. PEO coatings obtained in aluminate electrolyte showed similar change trend of tensile strength and shearing strength with increasing treating time, namely, a relatively high values with middle time treating and low value with short and long time treating. The best coating was the samples treated with 30 min, whose tensile strength was 20.6 MPa and shearing strength was 16 MPa. The tensile strength and shearing strength of coatings obtained in silicate electrolyte were not strongly influenced by the treating time, the values of which were range in 14 ± 2 MPa and 11 ± 2 MPa, respectively. Coatings obtained in both electrolytes showed the best thermal shock resistance with middle time treating. Coatings obtained in silicate electrolyte show a little better thermal shock resistance than those obtained in aluminate electrolyte.     

Microstructure development and properties of the AlCuFe quasicrystalline coating on near-α titanium alloy

A protective quasicrystalline AlFeCu coating was deposited on TIMETAL 834 substrate by nonreactive magnetron sputtering in order to improve resistance of the alloy to oxidation. Microstructure characterisation of the substrate and the coating was performed by analytical scanning- and transmission electron microscopy as well as X-ray diffractometry. Depending on annealing temperature and time, the deposited coating (2.7 μm thick) has a different microstructure. The coating in Specimen 1 (annealed 600 °C/4 h in vacuum) consisted of two zones: outer, composed of Al₅Fe₂ and Al₂Cu₃ phases and inner, in which only quasicrystalline ψ phase was present. The coating in Specimen 2 (annealed 600 °C/4 h + 700 °C/2 h in vacuum) was fully quasicrystalline and consisted of icosahedral ψ phase.Both coatings exhibit higher microhardness than the substrate material. It was established that the applied surface treatment essentially improves oxidation resistance of the alloy tested at 750 °C during 250 h in static air. Sample weight gain was 60% lower than in the case of uncoated sample. Oxide scale spallation occurred for uncoated alloy while the coated one did not show any spallation. It was found that the very brittle scale formed during oxidation on the uncoated alloy was consisting of TiO₂, while that on the coated one consisted mainly of α-Al₂O₃.     

Suspension plasma sprayed composite coating using amorphous powder feedstock

Al₂O₃-ZrO₂ composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al₂O₃ and tetragonal ZrO₂ phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al₂O₃ and ZrO₂ phases are homogeneously distributed in the composite coating.     

Improvement in the properties of plasma-sprayed metallic, alloy and ceramic coatings using dry-ice blasting

Dry-ice blasting, as an environmental-friendly method, was introduced into atmospheric plasma spraying for improving properties of metallic, alloy and ceramic coatings. The deposited coatings were then compared with coatings plasma-sprayed using conventional air cooling in terms of microstructure, temperature, oxidation, porosity, residual stress and adhesion. It was found that a denser steel or CoNiCrAlY alloy coating with a lower content of oxide can be achieved with the application of dry-ice blasting during the plasma spraying. In addition, the adhesive strength of Al₂O₃ coating deposited with dry-ice blasting exceeded 60 MPa, which was nearly increased by 30% compared with that of the coating deposited with conventional air cooling. The improvement in properties of plasma-sprayed metallic, alloy and ceramic coatings caused by dry-ice blasting was attributed to the decrease of annulus-ringed disk like splats, the better cooling efficiency of dry-ice pellets and even the mechanical effect of dry-ice impact.     

Heat treatment induced intermetallic phase transition of arc-sprayed coating prepared by the wires combination of aluminum-cathode and steel-anode

A method to prepare intermetallic composite coatings employing the cost-efficient electric arc spraying twin wires assistant with suitable heat treatment was developed. In this study, a Fe-Al composite coating was produced by spraying twin wires, i.e. a carbon steel wire as the anode and an aluminum wire as the cathode. The inter-deposited Fe-Al coating was transformed in-situ to Fe-Al intermetallic composite coating after a post annealing treatment. The effect of annealing treatment conditions on phase composition, microstructure and mechanical properties of the coating was investigated by using XRD, SEM, EDS and OM as well as microhardness tester. The results show that the desirable intermetallic phases such as Fe₂Al₅, FeAl and Fe₃Al are obtained under the annealing condition. The main oxide in the coating is FeO which can partially transform to Fe₃O₄ up to the annealing condition.