Chemical bath deposition of Bi2S3 films by a novel deposition system

Bismuth sulfide (Bi₂S₃) films were chemically deposited by a novel deposition system in which ammonium citrate was used as the chelating reagent. Two sulfur source thioacetamide (TA) and sodium thiosulfate (Na₂S₂O₃) were used to prepare Bi₂S₃ films. Both the as-prepared films have amorphous structure. However, annealing can improve the crystallization of the films. The composition of the films prepared by TA and Na₂S₂O₃ are all deviate from the stoichiometric ratio of Bi₂S₃. The Bi₂S₃ films are all homogeneous and well adhered to the substrate. The optical properties of the Bi₂S₃ films are studied. The electrical resistivity of the as-prepared films are all around 7 × 10³ Ω cm in dark, which decreases to around 1 × 10³ Ω cm under 100 mW/cm² tungsten-halogen illumination. After the annealing, the dark resistivity of the Bi₂S₃ film prepared by TA decreases by four magnitudes. In contrast, the dark resistivity of the Bi₂S₃ film prepared by Na₂S₂O₃ only decreases slightly.     

On the structure, morphology, and optical properties of chemical bath deposited Sb2S3 thin films

In the present paper, we have reported the room temperature growth of antimony sulphide (Sb₂S₃) thin films by chemical bath deposition and detailed characterization of these films. The films were deposited from a chemical bath containing SbCl₃ and Na₂S₂O₃ at 27 °C. We have analysed the structure, morphology, composition and optical properties of as deposited Sb₂S₃ films as well as those subjected to annealing in nitrogen atmosphere or in air. As-deposited films are amorphous to X-ray diffraction (XRD). However, the diffused rings in the electron diffraction pattern revealed the existence of nanocrystalline grains in these films. XRD analysis showed that upon annealing in nitrogen atmosphere these films transformed into polycrystalline with orthorhombic structure. Also, we have observed that during heating in air, Sb₂S₃ first converts into orthorhombic form and then further heating results in the formation of Sb₂O₃ crystallites. Optical bandgap energy of as deposited and annealed films was evaluated from UV-vis absorption spectra. The values obtained were 2.57 and 1.73 eV for the as-deposited and the annealed films respectively.     

Characterization of gallium-doped CdS thin films grown by chemical bath deposition

Ga-doped CdS thin films, with different [Ga]/[Cd] ratios, were grown using chemical bath deposition. The effect of Ga-doping on optical properties and bandgap of CdS films is investigated. Resistivity, carrier density, and mobility of doped films were acquired using Hall effect measurements. Crystal structure as well as crystal quality and phase transition were determined using X-ray diffraction (XRD) and Micro-Raman spectroscopy. Film morphology was studied using scanning electron microscopy, while film chemistry and binding states were studied using X-ray photoelectron spectroscopy (XPS). A minimum bandgap of 2.26 eV was obtained at [Ga]/[Cd] ratio of 1.7 × 10⁻². XRD studies showed Ga³⁺ ions entering the lattice substitutionally at low concentration, and interstitially at high concentration. Phase transition, due to annealing, as well as induced lattice defects, due to doping, were detected by Micro-Raman spectroscopy. The highest carrier density and lowest resistivity were obtained at [Ga]/[Cd] ratio of 3.4 × 10⁻². XPS measurements detect an increase in sulfur deficiency in doped films.     

Properties of In2S3 thin films deposited onto ITO/glass substrates by chemical bath deposition

In₂S₃ films have been chemically deposited on ITO coated glass substrates by chemical bath deposition, using different deposition times and precursor concentrations. The bilayers are intended for photovoltaic applications. Different characterization methods have been employed: optical properties of the films were investigated from transmittance measurements, structural properties by XRD and micro-Raman, and surface morphology by SEM microscopy analysis. Also, the direct and indirect band-gaps and the surface gap states were studied with surface photovoltage spectroscopy (SPS). We proposed that electronic properties of the In₂S₃ samples are controlled by two features: shallow tail states and a broad band centred at 1.5 eV approximately. Their relation with the structure is discussed, suggesting that their origin is related to defects created on the S sub-lattice, and then both defects are intrinsic to the material.     

Synthesis of CuS thin films by microwave assisted chemical bath deposition

In this study, oriented CuS nanoplates standing perpendicularly on F: SnO₂ (FTO) coated glass substrates have been prepared through a mild microwave assisted chemical bath deposition process in which copper acetate reacted with ethylenediamine tetraacetate acid disodium and thioacetamide in aqueous solution within 40 min. The effects of reaction time and microwave radiation on the treatment process were investigated. The morphology, structure, and composition of the yielded nanostructures have been confirmed by X-ray diffraction (XRD), energy-dispersive X-ray analysis (EDX), and scanning electron microscope (SEM). Also, the correlation between the reflectance, transmittance coefficient in the UV and the thickness of films was established. Furthermore, a two-point probe was used for resistivity measurements. We believe this simple chemical conversion technique can be further extended to the synthesis of other semiconductors with various morphologies.     

Investigation of chemical bath deposition of CdO thin films using three different complexing agents

Chemical bath deposition of CdO thin films using three different complexing agents, namely ammonia, ethanolamine, and methylamine is investigated. CdSO₄ is used as Cd precursor, while H₂O₂ is used as an oxidation agent. As-grown films are mainly cubic CdO₂, with some Cd(OH)₂ as well as CdO phases being detected. Annealing at 400 °C in air for 1 h transforms films into cubic CdO. The calculated optical band gap of as-grown films is in the range of 3.37-4.64 eV. Annealed films have a band gap of about 2.53 eV. Rutherford backscattering spectroscopy of as-grown films reveals cadmium to oxygen ratio of 1.00:1.74 ± 0.01 while much better stoichiometry is obtained after annealing, in accordance with the X-ray diffraction results. A carrier density as high as 1.89 × 10²⁰ cm⁻³ and a resistivity as low as 1.04 × 10⁻² Ω-cm are obtained.     

Nanomechanical characteristics of SnO2:F thin films deposited by chemical vapor deposition

The nanoindentation characterizations and mechanical properties of fluorine-doped tin oxide (SnO₂:F) films deposited on glass substrates, using chemical vapor deposition (CVD) method, were studied, which included the effects of the indentation loads, the loading time and the hold time on the thin film. The surface roughness, fractal dimension and frictional coefficient were also studied by varying the freon flow rates. X-ray diffraction (XRD), atomic force microscopy (AFM) and frictional force microscopy (FFM) were used to analyze the morphology of the microstructure. The results showed that crystalline structure of the film had a high intensity (1 1 0) peak orientation, especially at a low freon flow rate. According to the nanoindentation records, the Young's modulus ranged from 62.4 to 75.1 GPa and the hardness ranged from 5.1 to 9.9 GPa at a freon flow rate of 8000 sccm. The changes in measured properties were due to changing loading rate.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Effect of deposition time on structural, electrical, and optical properties of SnS thin films deposited by chemical bath deposition

The effect of deposition time on the structural, electrical and optical properties of SnS thin films deposited by chemical bath deposition onto glass substrates with different deposition times (2, 4, 6, 8 and 10 h) at 60 °C were investigated. The obtained films were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), energy dispersive X-ray analysis (EDX) and optical absorption spectra. All deposited films were polycrystalline and had orthorhombic structure with small crystal grains. Their microstructures had changed with deposition time, and their compositions were nearly stoichiometric. Electrical parameters such as resistivity and type of electrical conduction were determined from the Hall Effect measurements. Hall Effect measurements show that obtained films have p-type conductivity and resistivity values of SnS films have changed with deposition time. For allowed direct, allowed indirect, forbidden direct and forbidden indirect transitions, band gap values varied in the range 1.30-1.97 eV, 0.83-1.36 eV, 0.93-1.49 eV and 0.62-1.23 eV, respectively.     

Chemical bath deposition of hausmannite Mn3O4 thin films

A low-temperature chemical bath deposition (CBD) technique has been used for the preparation of Mn₃O₄ thin films onto glass substrates. The kinetic behavior and the formation mechanism of the solid thin films from the aqueous solution have been investigated. Structure (X-ray diffraction and Raman), morphological (atom force microscope), and optical (UV-vis-NIR) characterizations of the deposited films are presented. The results indicated that the deposited Mn₃O₄ thin films of smooth surface with nanosized grains were well crystalline and the optical bandgap of the film was estimated to be 2.54 eV.     

化学沉淀法制备硒化铅薄膜

采用化学沉淀的方法沉淀PbSe薄膜,分别加入缓冲剂联氨(方法A)和碘化钾(方法B)。对反应原理进行了分析,对制备过程进行了优化,分别制备出了高质量的PbSe薄膜。采用XRD、SEM、EDS以及红外光谱测试对所制备样品进行了分析。结果表明,两种方法制备均为PbSe多晶薄膜,方法A制备薄膜结晶质量更好,择优生长方向明显;薄膜颗粒度、表面粗糙度都小于方法B;两种薄膜的Pb元素与Se元素比例接近化学计量比,方法B含有少量I元素;两种方法制备样品的吸收边相对带边跃迁都发生蓝移。     

Preparation of Bi2S3 thin films with a nanoleaf structure by electrodeposition method

Nanoleaf-like Bi₂S₃ thin films were deposited on indium tin oxide (ITO) glass using Bi(NO₃)₃ and Na₂S₂O₃ as precursors by a cathodic electrodeposition process. The as-deposited thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and photoluminescence spectrum (PL). The influence of precursor solution mole concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] on the phase compositions, morphologies and photoluminescence properties of the obtained thin films were investigated. Results show that a uniform Bi₂S₃ thin film with nanoleaf structure can be obtained with the precursor solution concentration ratio [Bi(NO₃)₃]/[Na₂S₂O₃] = 1:7. The as-prepared thin films exhibit blue-green photoluminescence properties under ultraviolet light excitation. With the increase of concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] in the deposition solution, the crystallizations and PL properties of Bi₂S₃ thin films are obviously improved.     

Physical properties of ZnS thin films prepared by chemical bath deposition

Zinc sulphide thin films are deposited on SnO₂/glass using the chemical bath deposition technique. X-ray diffraction and atomic force microscopy are used to characterize the structure of the films; the surface composition of the films is studied by Auger electrons spectroscopy, the work function and the photovoltage are investigated by the Kelvin method. Using these techniques, we specify the effect of pH solution and heat treatment in vacuum at 500 °C. The cubic structure corresponding to the (1 1 1) planes of β-ZnS is obtained for pH equal to 10. The work function (Φ_material − Φ_probe) for ZnS deposited at pH 10 is equal to −152 meV. Annealing at 500 °C increases Φ_m (by about 43 meV) and induces the formation of a negative surface barrier. In all cases, Auger spectra indicate that the surface composition of zinc sulphide thin films exhibits the presence of the constituent elements Zn and S as well as C and O as impurity elements.     

CdS films deposited by chemical bath under rotation

Cadmium sulfide (CdS) films were deposited on rotating substrates by the chemical bath technique. The effects of the rotation speed on the morphological, optical, and structural properties of the films were discussed. A rotating substrate-holder was fabricated such that substrates can be taken out from the bath during the deposition. CdS films were deposited at different deposition times (10, 20, 30, 40 and 50 min) onto Corning glass substrates at different rotation velocities (150, 300, 450, and 600 rpm) during chemical deposition. The chemical bath was composed by CdCl₂, KOH, NH₄NO₃ and CS(NH₂)₂ as chemical reagents and heated at 75 °C. The results show no critical effects on the band gap energy and the surface roughness of the CdS films when the rotation speed changes. However, a linear increase on the deposition rate with the rotation energy was observed, meanwhile the stoichiometry was strongly affected by the rotation speed, resulting a better 1:1 Cd/S ratio as speed increases. Rotation effects may be of interest in industrial production of CdTe/CdS solar cells.     

化学溶液法制备的Pb(Mg1/3Nb2/3)O3-PbTiO3薄膜的光学性能

用化学溶液方法在宝石衬底及有LaNiO₃缓冲层的Pt/TiO₂/SiO₂/Si衬底上制备了92%Pb(Mg_1/3Nb_2/3)O₃-8%PbTiO₃(PMNT)薄膜，X射线衍射测试结果表明：在有LaNiO₃缓冲层的Pt/TiO₂/SiO₂/Si衬底上制备的PMNT薄膜几乎是纯钙钛矿相，且薄膜 关键词： PMNT薄膜 光学性能 化学溶液法     

Preparation and properties of zinc blende and orthorhombic SnS films by chemical bath deposition

SnS (stannous sulfide) films were prepared by chemical bath deposition in which a novel chelating reagent ammonium citrate was used. The film has a zinc blende structure or an orthorhombic structure which is determined by the pH value and the temperature of the deposition solution. The reason for this result is considered to be that SnS films prepared under different conditions have different deposition mechanisms (ion-by-ion mechanism for the zinc blende structured SnS and hydroxide cluster mechanism for the orthorhombic structured SnS). The prepared SnS films are homogeneous and well adhered. SEM images show that the SnS films with different structures have different surface morphologies. Electrical test shows that the resistivity of the films is as low as 420 Ω cm and 3300 Ω cm for orthorhombic and zinc blende SnS films, respectively, which are much lower than the ever reported values. Persistent photoconductivity (PPC) phenomena are observed for both the films with zinc blende and orthorhombic structures by photo-current responses measurement. The optical bandgaps of the SnS films are determined to be 1.75 eV and 1.15 eV for zinc blende structure and orthorhombic structure, respectively.     

Deposition of copper iodide thin films by chemical bath deposition (CBD) and successive ionic layer adsorption and reaction (SILAR) methods

In this paper, we report structural, morphological, electrical studies of copper iodide (CuI) thin films deposited onto glass substrates by chemical bath deposition (CBD) and successive ionic layer adsorption and reaction (SILAR) methods. CuI thin films were characterized for their structural, morphological and wettability studies by means of X-ray diffraction (XRD), FT-Raman spectroscopy, scanning electron microscopy (SEM), optical absorption, and contact angle measurement methods. Thickness of thin films was 1 ± 0.1 μm measured by gravimetric weight difference method. The CuI thin films were nanocrystalline, with average crystal size of ～60 nm. The FT-IR study confirmed the formation of CuI on the substrate surface. SEM images revealed the compact and cube like structure for CuI thin films deposited by CBD and SILAR methods, respectively. Optical absorption study revealed optical energy gaps as 2.3 and 3.0 eV for CBD and SILAR methods, respectively. Wettability study indicated that CuI thin films deposited by SILAR method are more hydrophobic as compared to CBD method.     

Growth of the Bi2O3 thin films under atmospheric pressure by means of halide CVD

Films of Bi₂O₃ were grown on glass substrate under atmospheric pressure by means of halide chemical vapour deposition (AP-HCVD) using BiI₃ and O₂ as the starting materials. In the XRD diffractogram of the film a strong diffraction peak appears at 27.91° assigned to the (111) diffraction of the δ-Bi₂O₃ with cubic structure. X-ray pole figure suggested that the 〈111〉 direction of the film is perpendicular to the substrate surface, while the 〈110〉 axis directs towards all directions parallel to the substrate surface. It is for the first that δ-Bi₂O₃ film was prepared on glass substrate.     

Characterization of poly (3-methyl thiophene) thin films prepared by modified chemical bath deposition

Poly (3-methyl thiophene) thin films were prepared by chemical bath deposition technique on glass substrate; the prepared thin films were characterized for structural, morphological and optical properties. The variation in the oxidant concentration has an influence on the properties of the P3MeT thin films. The increase in the oxidant concentration leads to increase in the thickness of the film. The binding energy increases due to increase in oxidation concentration. The P3MeT thin films show smooth surface morphology with increase in oxidant concentration whereas the contact angle of the thin film decreases with increase in oxidant concentration. The optical absorbance of these thin films was found to increase with decrease in the optical band gap due to increase in oxidant concentration.     

Preparation of CuInS2 thin films by metal-organic decomposition

Metal-organic decomposition (MOD) technique has been developed as a low cost thin film CuInS₂ preparation method for solar cell application. XRD and Raman spectra measurement revealed that deposited films contain CuInS₂. Stoichiometric films with a bandgap of 1.53 eV and an FWHM of 0.45° were obtained from a solution with Cu/In=1.5.