On the structure, morphology, and optical properties of chemical bath deposited Sb2S3 thin films

In the present paper, we have reported the room temperature growth of antimony sulphide (Sb₂S₃) thin films by chemical bath deposition and detailed characterization of these films. The films were deposited from a chemical bath containing SbCl₃ and Na₂S₂O₃ at 27 °C. We have analysed the structure, morphology, composition and optical properties of as deposited Sb₂S₃ films as well as those subjected to annealing in nitrogen atmosphere or in air. As-deposited films are amorphous to X-ray diffraction (XRD). However, the diffused rings in the electron diffraction pattern revealed the existence of nanocrystalline grains in these films. XRD analysis showed that upon annealing in nitrogen atmosphere these films transformed into polycrystalline with orthorhombic structure. Also, we have observed that during heating in air, Sb₂S₃ first converts into orthorhombic form and then further heating results in the formation of Sb₂O₃ crystallites. Optical bandgap energy of as deposited and annealed films was evaluated from UV-vis absorption spectra. The values obtained were 2.57 and 1.73 eV for the as-deposited and the annealed films respectively.     

Structural and electrical properties of (Na0.85K0.15)0.5Bi0.5TiO3 thin films deposited on LaNiO3 and Pt bottom electrodes

(Na_0.85K_0.15)_0.5Bi_0.5TiO₃ thin films were deposited on LaNiO₃(LNO)/SiO₂/Si(1 0 0) and Pt/Ti/SiO₂/Si(1 0 0) substrates by metal-organic decomposition, and the effects of bottom electrodes LNO and Pt on the ferroelectric, dielectric and piezoelectric properties were investigated by ferroelectric tester, impedance analyzer and scanning probe microscopy, respectively. For the thin films deposited on LNO and Pt electrodes, the remnant polarization 2P_r are about 22.6 and 8.8 μC/cm² under 375 kV/cm, the dielectric constants 238 and 579 at 10 kHz, the dielectric losses 0.06 and 0.30 at 10 kHz, the statistic d_33eff values 95 and 81 pm/V. The improved piezoelectric properties could make (Na_1−xK_x)_0.5Bi_0.5TiO₃ thin film as a promising candidate for piezoelectric thin film devices.     

Influence of [S2O3]/[Sm] on Sm2S3 thin films deposited by liquid phase deposition method on self-assembled monolayers

Sm₂S₃ thin films were prepared on Si (1 0 0) substrates using SmCl₃ and Na₂S₂O₃ as precursors by liquid phase deposition method on self-assembled monolayers. The influence of the molar concentration ratio of [S₂O₃²⁻]/[Sm³⁺] on the phase compositions, surface morphologies and optical properties of the as-deposited films were investigated. The as-deposited Sm₂S₃ thin films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM), ultraviolet-visible (UV-vis) and photoluminescence spectrum (PL). Results show that it is important to control the [S₂O₃²⁻]/[Sm³⁺] during the deposition process and monophase Sm₂S₃ thin films with orientation growth along (0 1 1) direction can be achieved when [S₂O₃²⁻]/[Sm³⁺] = 2.0, pH 3.0, with citric acid as a template agent. The as-deposited thin films exhibit a dense and crystalline surface morphology. Good transmittance in the visible spectrum and excellent absorbency of ultraviolet light of the thin films are observed, and the band gap of the thin films first decrease and then increase with the increase of the [S₂O₃²⁻]/[Sm³⁺]. The as-deposited thin films also exhibit red photoluminescence properties under visible light excitation. With the increase of the [S₂O₃²⁻]/[Sm³⁺] in the deposition solution, the PL properties of Sm₂S₃ thin films are obviously improved.     

A comparative study of the physical properties of Sb2S3 thin films treated with N2 AC plasma and thermal annealing in N2

As-deposited antimony sulfide thin films prepared by chemical bath deposition were treated with nitrogen AC plasma and thermal annealing in nitrogen atmosphere. The as-deposited, plasma treated, and thermally annealed antimony sulfide thin films have been characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy, scanning electron microscopy, atomic force microscopy, UV-vis spectroscopy, and electrical measurements. The results have shown that post-deposition treatments modify the crystalline structure, the morphology, and the optoelectronic properties of Sb₂S₃ thin films. X-ray diffraction studies showed that the crystallinity of the films was improved in both cases. Atomic force microscopy studies showed that the change in the film morphology depends on the post-deposition treatment used. Optical emission spectroscopy (OES) analysis revealed the plasma etching on the surface of the film, this fact was corroborated by the energy dispersive X-ray spectroscopy analysis. The optical band gap of the films (E_g) decreased after post-deposition treatments (from 2.36 to 1.75 eV) due to the improvement in the grain sizes. The electrical resistivity of the Sb₂S₃ thin films decreased from 10⁸ to 10⁶ Ω-cm after plasma treatments.     

Photovoltaic structures using AgSb(S x Se1−x )2 thin films as absorber

Photovoltaic structures were prepared using AgSb(S _x Se_1?x )₂ as absorber and CdS as window layer at various conditions via a hybrid technique of chemical bath deposition and thermal evaporation followed by heat treatments. Silver antimony sulfo selenide thin films [AgSb(S _x Se_1?x )₂] were prepared by heating multilayers of sequentially deposited Sb₂S₃/Ag dipped in Na₂SeSO₃ solution, glass/Sb₂S₃/Ag/Se. For this, Sb₂S₃ thin films were deposited from a chemical bath containing SbCl₃ and Na₂S₂O₃. Then, Ag thin films were thermally evaporated on glass/Sb₂S₃, followed by selenization by dipping in an acidic solution of Na₂SeSO₃. The duration of dipping was varied as 3, 4 and 5 h. Two different heat treatments, one at 350 °C for 20 min in vacuum followed by a post-heat treatment at 325 °C for 2 h in Ar, and the other at 350 °C for 1 h in Ar, were applied to the multilayers of different configurations. X-ray diffraction results showed the formation of AgSb(S _x Se_1?x )₂ thin films as the primary phase and AgSb(S,Se)₂ and Sb₂S₃ as secondary phases. Morphology and elemental detection were done by scanning electron microscopy and energy dispersive X-ray analysis. X-ray photoelectron spectroscopic studies showed the depthwise composition of the films. Optical properties were determined by UV–vis–IR transmittance and reflection spectral analysis. AgSb(S _x Se_1?x )₂ formed at different conditions was incorporated in PV structures glass/FTO/CdS/AgSb(S _x Se_1?x )₂/C/Ag. Chemically deposited post-annealed CdS thin films of various thicknesses were used as window layer. J–V characteristics of the cells were measured under dark and AM1.5 illumination. Analysis of the J–V characteristics resulted in the best solar cell parameters of V _oc = 520 mV, J _sc = 9.70 mA cm^?2, FF = 0.50 and η = 2.7 %.     

Chemical bath deposition of Bi2S3 films by a novel deposition system

Bismuth sulfide (Bi₂S₃) films were chemically deposited by a novel deposition system in which ammonium citrate was used as the chelating reagent. Two sulfur source thioacetamide (TA) and sodium thiosulfate (Na₂S₂O₃) were used to prepare Bi₂S₃ films. Both the as-prepared films have amorphous structure. However, annealing can improve the crystallization of the films. The composition of the films prepared by TA and Na₂S₂O₃ are all deviate from the stoichiometric ratio of Bi₂S₃. The Bi₂S₃ films are all homogeneous and well adhered to the substrate. The optical properties of the Bi₂S₃ films are studied. The electrical resistivity of the as-prepared films are all around 7 × 10³ Ω cm in dark, which decreases to around 1 × 10³ Ω cm under 100 mW/cm² tungsten-halogen illumination. After the annealing, the dark resistivity of the Bi₂S₃ film prepared by TA decreases by four magnitudes. In contrast, the dark resistivity of the Bi₂S₃ film prepared by Na₂S₂O₃ only decreases slightly.     

Preparation of Bi2S3 thin films with a nanoleaf structure by electrodeposition method

Nanoleaf-like Bi₂S₃ thin films were deposited on indium tin oxide (ITO) glass using Bi(NO₃)₃ and Na₂S₂O₃ as precursors by a cathodic electrodeposition process. The as-deposited thin films were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM) and photoluminescence spectrum (PL). The influence of precursor solution mole concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] on the phase compositions, morphologies and photoluminescence properties of the obtained thin films were investigated. Results show that a uniform Bi₂S₃ thin film with nanoleaf structure can be obtained with the precursor solution concentration ratio [Bi(NO₃)₃]/[Na₂S₂O₃] = 1:7. The as-prepared thin films exhibit blue-green photoluminescence properties under ultraviolet light excitation. With the increase of concentration ratios [Bi(NO₃)₃]/[Na₂S₂O₃] in the deposition solution, the crystallizations and PL properties of Bi₂S₃ thin films are obviously improved.     

Electrodeposition of Sb2Se3 on indium-doped tin oxides substrate: Nucleation and growth

The mechanisms related to the initial stages of the nucleation and growth of antimony selenide (Sb₂Se₃) semiconductor compounds onto the indium-doped tin oxides (ITO) coated glass surface have been investigated using chronoamperometry (CA) technique. The fabrication was conducted from nitric acid bath containing both Sb³⁺ and SeO₂ species at ambient conditions. No underpotential deposition (UPD) of antimony and selenium onto ITO substrate was observed in the investigated systems indicating a weak precursor-substrate interaction. Deposition of antimony and selenium onto ITO substrate occurred with large overvoltage through 3D nucleation and growth mechanism followed by diffusion limited growth. FE-SEM and XRD results show that orthorhombic phase Sb₂Se₃ particles with their size between 90 and 125 nm were obtained and the atomic ratio for antimony and selenium was 2:2.63 according to the EDX results.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Microstructural, optical and photocatalytic properties of CdS doped TiO2 thin films

CdS doped TiO₂ thin films (with CdS content=0, 3, 6, 9 and 12 at%) were grown on glass substrates. The X-ray diffraction analysis revealed that the films are polycrystalline of monoclinic TiO₂ structure. The microstructure parameters of the films such as crystallite size (D_ν) and microstrain (e) are calculated. Both the crystallites size and the microstrain are decreased with increasing CdS content. The optical constants have been determined in terms of Murmann's exact equations. The refractive index and extinction coefficient are increased with increasing CdS content. The optical band gap is calculated in the strong absorption region. The possible optical transition in these films is found to be an allowed direct transition. The values of E_g^opt are found to decrease as the CdS content increased. The films with 3 at% CdS content have better decomposition efficiency than undoped TiO₂. The films with 6 at% and 9 at% CdS content have decomposition efficiency comparable to that of undoped TiO₂, although they have lower band gap. The CdS doped TiO₂ could have a better impact on the decomposing of organic wastes.     

Preparation and characterization of Cu(In,Ga)(Se,S)2 films without selenization by co-sputtering from Cu(In,Ga)Se2 quaternary and In2S3 targets

In this study, Cu(In,Ga)(Se,S)₂ (CIGSS) thin films were deposited onto a bi-layer Mo coated soda-lime glass by co-sputtering a chalcopyrite Cu(In,Ga)Se₂ (CIGS) quaternary alloy target and an In₂S₃ binary target. A one-stage annealing process was performed to form CIGSS chalcopyrite phase without post-selenization. Experimental results show that CIGSS films were prepared by the proposed co-sputter process via CIGS (70 W by radio frequency) and In₂S₃ (30 W by direct current) with a substrate temperature of 373 K, working pressure of 0.67 Pa, and one-stage annealing at 798 K for 30 min. The stoichiometry ratios of the CIGSS film were Cu/(In + Ga) = 0.92, Ga/(In + Ga) = 0.26, and Se/(S) = 0.49 that approached device-quality stoichiometry ratio (Cu/(In + Ga) < 0.95, Ga/(In + Ga) < 0.3, and (Se/S) ≈ 0.5). The resistivity of the sample was 14.8 Ω cm, with a carrier concentration of 3.4 × 10¹⁷ cm⁻³ and mobility of 1.2 cm² V⁻¹ s⁻¹. The resulting film exhibited p-type conductivity with a double graded band-gap structure.     

Studies on electrodeposited As2S3 thin films by double exposure holographic interferometry technique

Arsenic trisulphide (As₂S₃) thin films have been deposited onto stainless steel and fluorine doped tin oxide (FTO) coated glass substrates by electrodeposition technique using arsenic trioxide (As₂O₃) and sodium thiosulphate (Na₂S₂O₃) as precursors and ethylene diamine tetracetic acid (EDTA) as a complexing agent. Double exposure holographic interferometry (DEHI) technique was used to determine the thickness and stress of As₂S₃ thin films. It was observed that the thickness of the thin film increases whereas film stress to the substrate decreases with an increase in the deposition time. X-ray diffraction and water contact angle measurements showed polycrystalline and hydrophilic surface respectively. The bandgap energy increases from 1.82 to 2.45 eV with decrease in the film thickness from 2.2148 to 0.9492 μm.     

Influence of annealing temperature on properties of Cu(In,Ga)(Se,S)2 thin films prepared by co-sputtering from quaternary alloy and In2S3 targets

Pentanary Cu(In,Ga)(Se,S)₂ (CIGSS) thin films were deposited on soda-lime glass substrate by co-sputtering quaternary alloy, and In₂S₃ targets. In this study, we investigated the influence of post-annealing temperature on structural, compositional, electrical, and optical properties of CIGSS films. Our experimental results show that the CIGS quaternary target had chalcopyrite characteristics. All CIGSS films annealed above 733 K exhibited a polycrystalline tetragonal chalcopyrite structure, with (1 1 2) preferred orientation. The carrier concentration and resistivity of the resultant CIGSS layer annealed above 763 K was 4.86×10¹⁶ cm⁻³ and 32 Ω cm, respectively, and the optical band-gap of the CIGSS absorber layer was 1.18 eV. Raman spectral analysis demonstrated the existence of many different phases, including CuInSe₂, CuGaSe₂, and CuInS₂. This may be because the vibration frequencies of In-Se, In-S bonds are similar to the Ga-Se and Ga-S bonds, causing their absorption bands overlap.     

Third-order nonlinear optical properties of Bi2S3 and Sb2S3 nanorods studied by the Z-scan technique

Bismuth sulfide (Bi₂S₃) and antimony sulfide (Sb₂S₃) nanorods were synthesized by hydrothermal method. The products were characterized by UV-vis spectrophotometer, X-ray powder diffraction (XRD) and transmission electron microscope (TEM). Bi₂S₃ and Sb₂S₃ nanorods were measured by Z-scan technique to investigate the third-order nonlinear optical (NLO) properties. The result of NLO measurements shows that the Bi₂S₃ and Sb₂S₃ nanorods have the behaviors of the third-order NLO properties of both NLO absorption and NLO refraction with self-focusing effects. The third-order NLO coefficient χ⁽³⁾ of the Bi₂S₃ and Sb₂S₃ nanorods are 6.25×10⁻¹¹ esu and 4.55×10⁻¹¹ esu, respectively. The Sb₂S₃ and Bi₂S₃ nanorods with large third-order NLO coefficient are promising materials for applications in optical devices.     

Effects of the substrate temperature on the properties of CuIn5S8 thin films

Structural, optical and electrical properties of CuIn₅S₈ thin films grown by thermal evaporation have been studied relating the effects of substrate heating conditions of these properties. The CuIn₅S₈ thin films were carried out at substrate temperatures in the temperature range 100-300 °C. The effects of heated substrate on their physico-chemical properties were investigated using X-ray diffraction (XRD), energy-dispersive X-ray spectroscopy (EDX), optical transmission and hot probe method. X-ray diffraction revealed that the films are strong preferred orientation along the (3 1 1) plane upon substrate temperature 200 °C and amorphous for the substrate temperatures below 200 °C. No secondary phases are observed for all the films. The composition is greatly affected by heated substrate. From the optical transmission and reflection, an important absorption coefficient exceeds 10⁵ cm⁻¹ at 800 nm was found. As increasing the substrate temperature, the optical energy band gap decreases from 1.70 eV for the unheated films to 1.25 eV for the deposited films at 300 °C. It was found that CuIn₅S₈ thin film is an n-type semiconductor at 250° C.     

Ferroelectric properties of bilayer structured Pb(Zr0.52Ti0.48)O3/SrBi2Ta2O9 (PZT/SBT) thin films on Pt/TiO2/SiO2/Si substrates

Pb(Zr_0.52Ti_0.48)O₃ (PZT) thin films with large remanent polarization and SrBi₂Ta₂O₉ (SBT) thin films with excellent fatigue-resisting characteristic have been widely studied for non-volatile random access memories, respectively. To combine these two advantages_, bilayered Pb(Zr_0.52Ti_0.48)O₃/SrBi₂Ta₂O₉ (PZT/SBT) thin films were fabricated on Pt/TiO₂/SiO₂/Si substrates by chemical solution deposition method. X-ray diffraction patterns revealed that the diffraction peaks of PZT/SBT thin films were completely composed of PZT and SBT, and no other secondary phase was observed. The electrical properties of the bilayered structure PZT/SBT films have been investigated in comparison with pure PZT and SBT films. PZT/SBT bilayered thin films showed larger remanent polarization (2P_r) of 18.37 μC/cm² than pure SBT and less polarization fatigue up to 1 × 10⁹ switching cycles than pure PZT. These results indicated that this bilayered structure of PZT/SBT is a promising material combination for ferroelectric memory applications.     

Chemical synthesis of nanocrystalline SnO2 thin films for supercapacitor application

Nanocrystalline SnO₂ thin films were deposited by simple and inexpensive chemical route. The films were characterized for their structural, morphological, wettability and electrochemical properties using X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy techniques (SEM), transmission electron microscopy (TEM), contact angle measurement, and cyclic voltammetry techniques. The XRD study revealed the deposited films were nanocrystalline with tetragonal rutile structure of SnO₂. The FT-IR studies confirmed the formation of SnO₂ with the characteristic vibrational mode of Sn-O. The SEM studies showed formation of loosely connected agglomerates with average size of 5-10 nm as observed from TEM studies. The surface wettability showed the hydrophilic nature of SnO₂ thin film (water contact angle 9°). The SnO₂ showed a maximum specific capacitance of 66 F g⁻¹ in 0.5 Na₂SO₄ electrolyte at 10 mV s⁻¹ scan rate.     

Stress dependence of growth mode change of epitaxial layered cobaltite γ-Na0.7CoO2

We report stress dependence of growth characteristics of epitaxial γ-Na_0.7CoO₂ films on various substrates deposited by pulsed laser deposition method. On the sapphire substrate, the γ-Na_0.7CoO₂ thin film exhibits spiral surface growth with multi-terraces and highly crystallized texture. For the γ-Na_0.7CoO₂ thin film grown on the (1 1 1) SrTiO₃ substrate, the nano-islands of ∼30 nm diameter on the hexagonal grains are observed. These islands indicate that the growth mode changes from step-flow growth mode to Stranski-Krastanow (SK) growth mode. On the (1 1 1) MgO substrate, the large grains formed by excess adatoms covering an aperture between hexagonal grains are observed. These experimental demonstrations and controllability could provide opportunities of strain effects of Na_xCoO₂, physical properties of thin films, and growth dynamics of heterogeneous epitaxial thin films.     

In situ X-ray photoelectron spectroscopy characterization of Al2O3/GaSb interface evolution

GaSb(0 0 1) was treated with (NH₄)₂S_x and the evolution of the interfacial chemistry was investigated, in situ, with monochromatic X-ray photoelectron spectroscopy (XPS), following heat treatment and exposure to trimethylaluminum (TMA) and deionized water (DIW) in an atomic layer deposition reactor. Elemental Sb (Sb-Sb bonding) as well as Sb³⁺ and Sb⁵⁺ chemical states were initially observed at the native oxide/GaSb interface, yet these diminished below the XPS detection limit after heating to 300 °C. No evidence of Ga-Ga bonding was observed whereas the Ga¹⁺/Ga-S chemical state was robust and persisted after heat treatment and exposure to TMA/DIW at 300 °C.     

Surface characterization and luminescent properties of SrAl2O4:Eu,Dy nano thin films

SrAl₂O₄:Eu²⁺, Dy³⁺ thin films were grown on Si (1 0 0) substrates in different atmospheres using the pulsed laser deposition (PLD) technique. The effects of vacuum, oxygen (O₂) and argon (Ar) deposition atmospheres on the structural, morphological and photoluminescence (PL) properties of the films were investigated. The films were ablated using a 248 nm KrF excimer laser. Improved PL intensities were obtained from the unannealed films prepared in Ar and O₂ atmospheres compared to those prepared in vacuum. A stable green emission peak at 520 nm, attributed to 4f⁶5d¹→4f⁷ Eu²⁺ transitions was obtained. After annealing the films prepared in vacuum at 800 °C for 2 h, the intensity of the green emission (520 nm) of the thin film increased considerably. The amorphous thin film was crystalline after the annealing process. The diffusion of adventitious C into the nanostructured layers deposited in the Ar and O₂ atmospheres was most probably responsible for the quenching of the PL intensity after annealing.