Flame structure studies of rich ethylene-oxygen-argon mixtures doped with CO2, or with NH3, or with H2O

Structures of several premixed ethylene-oxygen-argon rich flat flames burning at 50 mbar have been established by using molecular beam mass spectrometry in order to investigate the effect of CO₂, or NH₃, or H₂O addition on species concentration profiles. The aim of this study is to examine the eventual changes of profiles of detected hydrocarbon intermediates which could be considered as soot precursors (C₂H₂, C₄H₂, C₅H₄, C₅H₆, C₆H₂, C₆H₄, C₆H₆, C₇H₈, C₆H₆O, C₈H₆, C₈H₈, C₉H₈ and C₁₀H₈). The comparative study has been achieved on four flames with an equivalence ratio (f) of 2.50: one without any additive (F2.50), one with 15% of CO₂ replacing the same quantity of argon (F2.50C), one with 3.3% of NH₃ in partial replacement of argon (F2.50N) and one with 13% of H₂O in replacement of the same quantity of argon (F2.50H). The four flat flames have similar final flame temperatures (1800 K).CO₂, or NH₃, or H₂O addition to the fresh gas inlet causes a shift downstream of the flame front and thus flame inhibition. Endothermic processes CO₂ + H = CO + OH and H₂O + H = H₂ + OH are responsible of the reduction of the hydrocarbon intermediates in the CO₂ and H₂O added flames through the supplementary formation of hydroxyl radicals. It has been demonstrated that such processes begin to play at the end of the flame front and becomes more efficient in the burnt gases region.The replacement of some Ar by NH₃ is responsible only for a slight decrease of the maximum mole fraction of C₂H₂, but NH₃ becomes much more efficient for C₄H₂ and C₅ to C₁₀ species. Moreover, the efficiency of NH₃ as a reducing agent of C₅ to C₁₀ intermediates is larger than that of CO₂ and H₂O for equal quantities added.     

CO2 laser assisted removal of UO2 and ThO2 particulates from metal surface

Pulsed laser assisted removal of uranium dioxide and thorium dioxide particulates from stainless steel surface have been studied using a TEA CO₂ laser. Decontamination efficiency is measured as a function of laser fluence and number of pulses. Threshold fluence for the removal of UO₂ particulates has been found to be lower than that required for the removal ThO₂ particulates. Usage of a ZnSe substrate, that is transparent to the laser wavelength used here, enabled us to decouple the cleaning effect arising out of absorption in the particulates from that in the substrate and has contributed towards understanding the mechanism responsible for cleaning. The experimental observations are also corroborated by simple theoretical calculations.     

Improvement of amine-modification with piperazine for the adsorption of CO2

Both selectivity and capacity of CO₂ adsorption were considerably increased when PZ (piperazine) was added in MDEA (methyldiethylamine) that used to modify the surface of silica gels. The adsorbent saturated with CO₂ was regenerated at ambient temperature through nitrogen purge. A set of PSA (pressure swing adsorption) operation with 200 cycles was carried out and applicability of the modified adsorbent was thus illustrated. The CO₂ content in the column-top stream decreased from 13% to below 0.05% at steady state.     

CO2 dissociation on Ni(2 1 1)

The direct and H-mediated dissociation of CO₂ on Ni(2 1 1) were investigated at the level of density functional theory. Although formate (HCOO) formation via CO₂ hydrogenation was widely reported for CO₂ adsorption on metal surfaces, it is found that on Ni(2 1 1) HCOO dissociation into CHO and O is much difficult, while direct dissociation of adsorbed CO₂ into CO and O is more favorable. It is also found that the degree of electron transfer from surface to adsorbed CO₂ correlates with the elongation of C-O bond lengths and the reduction of the CO₂ dissociation barrier.     

Ammoxidation of carbon materials for CO2 capture

Ammoxidised carbons were produced from three different starting materials: an activated carbon obtained from wood by chemical activation using the phosphoric acid process, a steam activated peat-based carbon, and a char obtained from a low-cost biomass feedstock, olive stones. Nitrogen was successfully incorporated into the carbon matrix of the different materials, the amount of nitrogen uptake being proportional to the oxygen content of the precursor. At room temperature the CO₂ capture capacity of the samples was found to be related to the narrow micropore volume, while at 100 °C other factors such as surface basicity took on more relevance. At 100 °C all the ammoxidised samples presented an enhancement in CO₂ uptake compared to the parent carbons.     

Adsorption of CO, CO2 and NO molecules on a BaTiO3 (0 0 1) surface

Since the development of Scanning Tunnelling Microscopy (STM) technique, considerable attention has been devoted to various molecules adsorbed on various surfaces. Also, a new concept emerged with molecules on surfaces considered as nano machines by themselves. In this context, a thorough knowledge of surfaces and adsorbed molecules at an atomic scale are thus particularly invaluable. The present work describes the first Density Functional Theory (DFT) study of adsorption of CO, CO₂ and NO molecules on a BaTiO₃ surface following a first preliminary calculation of O and O₂ adsorption on the same surface. In the previously considered work, we found that a (0 0 1) surface with BaO termination is more stable than the one with TiO₂-termination. Consequently, we extended our study to CO, CO₂ and NO molecules adsorbed on a (0 0 1) surface with BaO termination. The present calculation was performed on a (1 × 1) cell with one monolayer of adsorbed molecules. Especially, a series of cases implying CO molecules adsorbed in various geometrical configurations has been examined. The corresponding adsorption energy varies in the range of −0.17 to −0.10 eV. The adsorption energy of a CO₂ molecule directly located above an O surface atom (called O_s) is of the order of −0.18 eV. The O-C distance length is then 1.24 Å and the O-C-O and O-C-O_s angles are 134.0° and 113.0°, respectively. For NO adsorption, the most important induced structural changes are the followings: (i) the N-O bond is broken when a NO molecule is absorbed on a Ba-O_s bridge site. In that case, N and O atoms are located above an O and a Ba surface atom, respectively, whereas the O-Ba-O_s and N-O_s-Ba angles are 106.5° and 63.0°, respectively. The N-O distance is as large as 2.58 Å and the adsorption energy is as much as −2.28 eV. (ii) In the second stable position, the NO molecule has its N atom adsorbed above an O_s atom, the N-O axis being tilted toward the Ba atom. The N-O_s-Ba angle is then 41.1° while the adsorption energy is only −0.10 eV. At last, the local densities of states around C, O as well as N atoms of the considered adsorbed molecules have also been discussed.     

The Raman spectra and cross-sections of the ν2 band of H2O, D2O, and HDO

We report the experimental Raman spectra of the ν₂ band of H₂O, D₂O, and HDO in the vapor phase at room temperature. A complete interpretation of the Raman intensities is carried out employing the variational rovibrational wavefunctions obtained from a Hamiltonian in Radau coordinates and an ab initio polarizability surface at 514.5 nm. We show the importance of the rotation-vibration coupling to obtain the correct line intensities. Several tables with the assignments of the individual rotational-vibrational transitions and their Raman scattering strengths are reported. From these tables, the ν₂ Raman spectra can be simulated up to 2000 K for H₂O, and up to 300 K for D₂O and HDO.     

Homogeneous ignition of CH4/air and H2O and CO2-diluted CH4/O2 mixtures over Pt; an experimental and numerical investigation at pressures up to 16 bar

The homogeneous ignition of CH₄/air, CH₄/O₂/H₂O/N₂, and CH₄/O₂/CO₂/N₂ mixtures over platinum was investigated experimentally and numerically at pressures 4 bar p 16 bar, temperatures 1120 K T 1420 K, and fuel-to-oxygen equivalence ratios 0.30 0.40. Experiments have been performed in an optically accessible catalytic channel-flow reactor and included planar laser induced fluorescence (LIF) of the OH radical for the determination of homogeneous (gas-phase) ignition and one-dimensional Raman measurements of major species concentrations across the reactor boundary layer for the assessment of the heterogeneous (catalytic) processes preceding homogeneous ignition. Numerical predictions were carried out with a 2D elliptic CFD code that included elementary heterogeneous and homogeneous chemical reaction schemes and detailed transport. The employed heterogeneous reaction scheme accurately captured the catalytic methane conversion upstream of the gaseous combustion zone. Two well-known gas-phase reaction mechanisms were tested for their capacity to reproduce measured homogeneous ignition characteristics. There were substantial differences in the performance of the two schemes, which were ascribed to their ability to correctly capture the p–T– parameter range of the self-inhibited ignition behavior of methane. Comparisons between measured and predicted homogeneous ignition distances have led to the validation of a gaseous reaction scheme at 6 bar p 16 bar, a pressure range of particular interest to gas-turbine catalytically stabilized combustion (CST) applications. The presence of heterogeneously produced water chemically promoted the onset of homogeneous ignition. Experiments and predictions with CH₄/O₂/H₂O/N₂ mixtures containing 57% per volume H₂O have shown that the validated gaseous scheme was able to capture the chemical impact of water in the induction zone. Experiments with CO₂ addition (30% per volume) were in good agreement with the numerical simulations and have indicated that CO₂ had only a minor chemical impact on homogeneous ignition.     

Optical pumping by CO2 and N2O lasers: New cw FIR emissions in vinyl cyanide

A systematical study of optical pumping by CO₂ and N₂O lasers using a FIR metallic waveguide has been undertaken in vinyl cyanide. 97 new FIR laser lines are reported in the wavelength range 400 m–1,5 mm.Unité associée au CNRS (UA 836).     

CO2 laser cutting of slate

Slate is a natural stone which has the characteristic that shows a well-developed defoliation plane, allowing to easily split it in plates parallel to that plane which are particularly used as tiles for roof building. At present, the manufacturing of slate is mostly manual, being noisy, powdery and unsafe for the worker. Thus, there is a need to introduce new processing methods in order to improve both the working conditions and the quality of the products made of slate.Following the previous work focused on the drilling and cutting of slate tiles using a Nd : YAG laser, we present in this paper the results of the work carried out to explore the possibilities to cut slate plates by using a CO₂ laser. A 1.5 kW CO₂ laser was used to perform different experiments in which, the influence of some processing parameters (average power, assist gas pressure) on the geometry and quality of the cut was studied. The results obtained show that the CO₂ laser is a feasible tool for a successful cutting of slate.     

Spatial-dependent simulation of TEA CO2 lasers

We have developed a 1-D spatially-dependent model and simulation code to study the dynamics of TEA CO₂ lasers. In this paper we will discuss the motivation for developing the model and present the simulation details. We have compared and verified the simulation results with the previous 0-D model, and with the measurements of a TEA CO₂ laser. With spatial resolution, the 1-D simulation is in better agreement with experimental results compared with the existing 0-D model.     

Mathematical modeling of hybrid CO2 laser

A Teller–Landau six-temperature model describing the dynamic emission of single-mode TEA CO₂ laser has been adapted. This model has been also used to describe the mechanism of obtaining relatively high-power output pulses from hybrid TE-TEA or CW-TEA CO₂ laser consisting of high- and low-pressure sections. The suggested mathematical model allows to investigate the mechanism which limits the TEA oscillation to single longitudinal mode (SLM) due to the narrow gain bandwidth of low-pressure section, and also to study the effect of the laser input parameters on the smooth output laser pulse parameters. In addition, numerical solutions of non-linear rate equation system of the suggested model are quantitatively discussed. The solutions describe the radiation field intensity, the population inversion, and the energy transfer processes. The calculated values of maximum peak power, total energy in pulse, pulse width, etc. are in a very good agreement with the observed experimental values.     

Surface modification of activated carbons for CO2 capture

The reduction of anthropogenic CO₂ emissions to address the consequences of climate change is a matter of concern for all developed countries. In the short term, one of the most viable options for reducing carbon emissions is to capture and store CO₂ at large stationary sources. Adsorption with solid sorbents is one of the most promising options. In this work, two series of materials were prepared from two commercial activated carbons, C and R, by heat treatment with gaseous ammonia at temperatures in the 200-800 °C range. The aim was to improve the selectivity and capacity of the sorbents to capture CO₂, by introducing basic nitrogen-functionalities into the carbons. The sorbents were characterised in terms of texture and chemical composition. Their surface chemistry was studied through temperature-programmed desorption tests and X-ray photoelectron spectroscopy. The capture performance of the carbons was evaluated by using a thermogravimetric analyser to record mass uptakes by the samples when exposed to a CO₂ atmosphere.     

特定位点上CO2与(TiO2)n团簇相互作用的第一性原理研究

本文基于密度泛函理论系统地研究了(TiO₂)_n团簇上二氧化碳(CO₂)的吸附和活化性质. 计算结果表明,CO₂更倾向于吸附在(TiO₂)_n团簇的桥氧原子上,形成“化学吸附”碳酸盐络合物. 而CO更倾向于吸附到末端Ti-O的Ti原子上. 发现计算得到的碳酸盐振动频率值与实验获得的结果非常吻合,这表明配合物中CO₂的几何构型与其线性型相比,有微小的弯转. 通过对电子结构、电荷密度、电离势、HOMO-LUMO以及态密度的分析,证实了CO₂与团簇之间的电荷转移以及相互作用. 从预测的能量分布图来看,(TiO₂)_n团簇上的CO₂活化与结构密切有关,相比于块体的TiO₂,CO₂在团簇结构上更易于吸附和活化.     

Optically pumped submillimeter laser lines from CD2Cl2 using a large tunability CW CO2 laser

Twenty-five new laser lines have been obtained in the wavelength region from 155 to 830 μm by optically pumping the CD₂Cl₂ (deuterated dichloromethane) molecule with a CW CO₂ laser having a tunability range of 300 MHz. The wavelength, polarization relative to that of CO₂ pumping radiation, and offset relative to the CO₂ center frequency were determined for all of the new lines and some other already known laser emissions. For all of them we give also the relative intensity and the optimum pressure of operation. Permanent address: Depto de Física e Química da FEIS — UNESP 15.378-000 Ilha Solteira-SP, Brazil     

Synthesis and CO2 capture property of high aspect-ratio Li2ZrO3 nanotubes arrays

High aspect-ratio Li₂ZrO₃ nanotubes were prepared by hydrothermal method using ZrO₂ nanotubes layers as templates. Characterizations of SEM, XRD, TEM and CO₂ adsorption were performed. The results showed that tetragonal Li₂ZrO₃ nanotubes arrays containing a little monoclinic ZrO₂ can be obtained using this simple method. The mean diameter of the nanotubes is approximately 150 nm and the corresponding specific surface area is 57.9 m² g⁻¹. Moreover, the obtained Li₂ZrO₃ nanotubes were thermally analyzed under a CO₂ flow to evaluate their CO₂ capture property. It was found that the as-prepared Li₂ZrO₃ nanotubes arrays would be an effective acceptor for CO₂ at high temperature.     

Line shape of the far-wing beyond the band head of the CO2ν3 band

Carbon dioxide is one of the most important trace gases in the terrestrial atmosphere. The spectral data required in remote sensing are the spectral parameter of each absorption line and a line shape model. This paper describes the absorption properties of CO₂ near 2400 cm⁻¹; these properties are of interest to those in the atmospheric temperature sounding field. The shape of the far-wing of N₂- and O₂-broadened CO₂ lines was investigated in the 2200-2500 cm⁻¹ spectral region in a temperature range of atmospheric interest (230-318 K). We focused on the higher rotational quantum number of the R-branch in the ν₃ band, where the effect of the far-wing is enhanced. The effect of the far-wing has been studied extensively by others, since the CO₂ν₃ band is known to exhibit sub-Lorentzian behavior. Here, we show the observed spectra along with calculated spectra for five temperatures. We used first-order line-mixing and the χ-factor, which accounts for the effect of the far-wing, to create the calculated spectra. Our results provide new knowledge of quantum interference of the spectral line in the ν₃ band of CO₂.     

Absolute frequency measurement of CO2 laser lines with a femtosecond laser comb and new determination of the CO2 molecular constants and frequency grid

Absolute frequency measurements of a CO₂ laser stabilized on saturated absorption resonances of CO₂ laser lines are reported. They were performed using a femtosecond-laser frequency comb generator and two laser diodes at 852 and 782 nm as intermediate oscillators, with their frequency difference phase-locked to the CO₂ laser. Twenty ¹²C¹⁶O₂ laser lines in the P and R bands at 9 μm were measured with a relative uncertainty of a few 10⁻¹² limited by the CO₂ frequency reproducibility. A new determination of the CO₂ molecular constants was obtained from these data and previous measurements in the 10 μm band. The CO₂ frequency grid was also calculated, with an improvement of two orders of magnitude compared to the previous grid of Maki et al. [J. Mol. Spectrosc. 167 (1994) 211].     

Slab CO2 lasers excited by switching power

In this paper we present a new discharge technique to excite slab CO₂ lasers. A uniform stable glow discharge has been obtained in a volume of 3 × 30 × 446 mm³. Output power is 10 W, and a gain of 0.26% cm⁻¹ has been obtained.     

Mathematical modeling of tunable TEA CO2 lasers

A mathematical model, based on the Landau–Teller equations of six-temperature model for the CO₂–N₂–He–CO system, to describe the process of dynamic emission in tunable TEA CO₂ lasers is introduced. In this model, the Landau–Teller equations are rewritten with regard to fine longitudinal mode frequencies in the laser resonator. These revised equations can be utilized to estimate the laser output spectra as well as other laser output pulse parameters. Examples are given to show the modeling results of non-tunable, grating tuned or injection-locking TEA CO₂ lasers.