超声场对钛基PbO2电极电化学氧化Cr3+过程电流效率的影响

本文研究了超声场对Ti／SnO2 Sb2O3／PbO2电极电化学氧化Cr3 过程的影响,探讨了在不同的操作电流密度、反应温度、硫酸浓度及Cr3 浓度下,超声场对硫酸介质中Cr3 电化学氧化生成Cr2O72-过程中的电流效率的影响,并用扫描电镜对有无超声场时不同反应时间下的电极形貌进行了分析。实验结果表明:在相同的反应条件下,有超声场作用时Cr3 电化学氧化过程的电流效率明显高于无超声场时的电流效率。扫描电镜测定发现,有超声场作用时不同反应时间下电极的形貌有明显的变化。     

The influence of interfacial barrier engineering on the resistance switching of In2O3：SnO2/TiO2/In2O3：SnO2 device

The I-V characteristics of In2O3：SnO2/TiO2/In2O3：SnO2 junctions with different interracial barriers are inves- tigated by comparing experiments. A two-step resistance switching process is found for samples with two interfacial barriers produced by specific thermal treatment on the interfaces. The nonsynchronous occurrence of conducting filament formation through the oxide bulk and the reduction in the interracial barrier due to the migration of oxygen vacancies under the electric field is supposed to explain the two-step resistive switching process. The unique switching properties of the device, based on interracial barrier engineering, could be exploited for novel applications in nonvolatile memory devices.     

Preparation, characterization and electrochemical property of Sn-Fe-Mo-Al2O3 multi-phase composites

A novel technique has been developed to synthesize Sn-Fe-Mo-Al₂O₃, while nanoscale dispersion of a highly active tin phase was finely distributed in a stable inert multi-phase. The precursor was prepared by co-precipitation method with SnCl₄, FeCl₃, AlCl₃ and (NH₄)₆Mo₇O₂₄ as the raw materials. Sn-Fe-Mo-Al₂O₃ mixture was produced by reducing the precursor with H₂. The product was characterized by X-ray diffraction (XRD), ICP and scanning electron microscopy (SEM). The performance of the electrode was investigated. The Sn-Fe-Mo-Al₂O₃ electrode was found to have an initial charge capacity of over 461 mAh/g, and a reversible volumetric capacity of 2090 mAh/cm³, which is two times larger than that of graphite electrode (800 mAh/cm³). The coulomb efficiency in the first cycle was over 55%, but its cyclability was not improved significantly. In order to enhance the cycle performance, we investigated the anode after heat treated at 270 °C for 12 h. Under the same condition, the first charge-discharge characteristics were almost equivalent to the as-coated anode, and the retention capacity ratio after 20 cycles was improved from 41.1% to 86.5%. The heat-treated Sn-Fe-Mo-Al₂O₃ electrode exhibited better cycle life. The electrochemical reaction of the Sn-Fe-Mo-Al₂O₃ electrode with Li may obey the alloying-dealloying mechanism of Li_xSn(x?4.4) formation in the other tin-based electrodes.     

The thermal spreading of antimony oxides onto Fe2O3

The uniform antimony-rich surface layer on Fe₂O₃ was carried out via thermal spreading of Sb₂O₃ and Sb₂O₄. TG–DTA results indicate that the oxidation temperature of Sb₂O₃ was decreased ca. 100 K due to thermal spreading effect. Although Sb₂O₄ is almost catalytically inert for oxidation of isobutane and Fe₂O₃ is a typical non-selective catalyst for this reaction, the formation of antimony-rich layer suppresses the combustion reactions and favors the partial oxidation reactions. When Sb₂O₄ instead of Sb₂O₃ was used as antimony resource, the enrichment of antimony on Fe₂O₃ surface was much lower. However, the reaction atmosphere of isobutane oxidation enhances antimony spreading over Fe₂O₃ surface. According to Mars–Van Krevelen mechanism, some Sb₂O₄ in catalysts could be intermediately reduced into Sb₂O₃ during reaction of isobutene oxidation, which thermal spreading is much easier. As shown by Raman results, the Sb₂O₄ that has been spread on Fe₂O₃ surface is probably amorphous.     

Performance of different crystal structures of PbO2 on electrochemical degradation of phenol in aqueous solution

Phenol degradation was carried out in acidic aqueous solution on different crystal structures of PbO₂ surfaces at room temperature. Phenol, benzoquinone and maleic acid concentrations were monitored during the electrolysis process. It was determined that β surfaces have higher performance than surfaces on phenol degradation. Then, the effect of crystallinities of pure β-PbO₂ surfaces was investigated and found that higher crystallinity increased the efficiency of the phenol degradation process.     

SnO2 / In2O3 one-dimensional nano-core-shell structures: Synthesis, characterization and photoluminescence properties

SnO₂/In₂O₃ one-dimensional nano-core-shell structures have been synthesized at 1350 ^°C by thermal evaporation of the mixture of metal Sn, Fe(NO₃)₃ powders and In particles. The as-synthesized products have been characterized by energy-dispersive X-ray spectroscopy, selected-area electron diffraction and high-resolution transmission electron microscopy. Microstructure characterization indicates the orientation relationship between core and shell is , . The formation mechanism of this nano-core-shell structure can be attributed to the cover of In₂O₃ on the surface of SnO₂ nanochains. The photoluminescence properties of the nano-core-shell structures have been measured. The PL spectrum shows some difference with the result from pure SnO₂ and In₂O₃ nanostructure that be deemed to relate to interface defects in SnO₂/In₂O₃ nano-core-shell structure.     

Facile synthesis and electrochemical properties of hierarchical MnO2 submicrospheres and LiMn2O4 microspheres

Hierarchical MnO₂ submicrospheres have been successfully synthesized by a wet chemical method. The as-prepared products were characterized by means of XRD, SEM, FTIR, TG, and TEM. With the as-prepared MnO₂ submicrospheres as precursors, LiMn₂O₄ microspheres were conveniently prepared by a simple solid-state reaction between MnO₂ and LiOH at a temperature as low as 600 °C. Electrochemical properties of the as-prepared MnO₂ submicrospheres and LiMn₂O₄ microspheres as cathode materials in lithium ion cells were investigated by galvanostatic charge/discharge tests.     

Al2O3 supported Ru catalysts prepared by thermolysis of Ru3(CO)12 for catalytic wet air oxidation

Low loading catalysts Ru/γ-Al₂O₃ and Ru-Ce/γ-Al₂O₃ were prepared by thermolysis of Ru₃(CO)₁₂ on γ-Al₂O_3. The catalysts were characterized by XPS, XRD and SEM. Two new Ru species (Ru_A and Ru_B) were detected during the Ru₃(CO)₁₂ decomposition process due to chemical interaction with the active OH groups on the surface of Al₂O₃ support, and the reduction of them can lead to more dispersed metallic phases. The sample was completely decomposed at 673 K in H₂, and RuO₂ was formed with minor amounts of Ru⁰. When the temperature was increased to 773 K to heat the sample, the ratio of Ru⁰ to RuO₂ increased. However, after the addition of CeO₂, only RuO₂ was detected on surface. The catalysts exhibited high activities in Catalytic Wet Air Oxidation (CWAO) of different organic compounds at high concentration such as isopropyl alcohol, phenol, acetic acids and N,N-dimethylformamide, which is attributed to the better dispersion of Ru particles and the addition of CeO₂ further enhanced number of effectively active sites on the cluster-derived catalyst surface.     

MAO-synthesized Al2O3-supported V2O5 nano-porous catalysts: Growth, characterization, and photoactivity

V₂O₅-loaded Al₂O₃ layers were successfully grown via micro-arc oxidation (MAO) process for the first time. Surface morphology and topography of the layers were investigated by scanning electron microscope (SEM) and atomic force microscope (AFM). It was found that the composite layers had a porous structure with a rough surface which is suitable for catalytic applications. X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and energy dispersive X-ray spectroscopy (EDS) techniques were also employed to study phase structure and chemical composition of the composite layers. The layers consisted of γ-alumina, α-alumina, and vanadium pentoxide phases in which their relative contents varied with the applied voltage. Meanwhile, optical properties of the composite layers were investigated using UV-vis spectrophotometry technique, and the band gap energy was calculated as 3.15 eV. Furthermore, photocatalytic performance of the synthesized composite layers was determined by measuring the decomposition rate of methylene blue solution, as a model compound, on the surface of the layers under ultra violet photo-irradiation. It was found that more than 91% of the methylene blue was degraded after 120 min with a rate constant of k = 0.0192 min⁻¹.     

Facile synthesis of Nb2O5 nanorod array films and their electrochemical properties

Nb₂O₅ nanorod array films were synthesized by a facile hydrothermal process using niobium metal foil and NH₄F as precursors. The Nb₂O₅ nanorods stand on the niobium metal foil substrate and are less than 100 nm in diameter and about 1 μm in length. X-ray diffraction (XRD) and high resolution transmission electron microscopy (HRTEM) characterizations indicate that these nanorods have orthorhombic structure and grew longitudinally along 〈0 0 1〉 direction. The nanorod growth mechanism was discussed. Thermal annealing at a temperature below 500 °C did not change the microstructure of nanorods but improve the crystallinity. The Nb₂O₅ nanorod array films have been tested as cathode material for lithium battery, which showed a good specific capacity up to 380 mAh g⁻¹ even after 50 charge/discharge cycles.     

Composite SiO2/TiO2 and amine polymer/TiO2 nanoparticles produced using plasma-enhanced chemical vapor deposition

Plasma-enhanced chemical vapor deposition was used to conformally coat commercial TiO₂ nanoparticles to create nanocomposite materials. Hexamethyldisiloxane (HMDSO)/O₂ plasmas were used to deposit SiO₂ or SiO_xC_yH_z films, depending on the oxidant concentration; and hexylamine (HexAm) plasmas were used to deposit amorphous amine-containing polymeric films on the TiO₂ nanoparticles. The composite materials were analyzed using Fourier-transform infrared spectroscopy (FTIR), X-ray photoelectron spectroscopy (XPS) and scanning electron microscopy (SEM). These analyses reveal film composition on the nanoparticles was virtually identical to that deposited on flat substrates and that the films deposit a conformal coating on the nanoparticles. The performance of the nanocomposite materials was evaluated using UV-vis spectroscopy to determine the dispersion characteristics of both SiO_x and HexAm coated TiO₂ materials. Notably, the coated materials stay suspended longer in distilled water than the uncoated materials for all deposited films.     

Growth Mechanism and Characterization of Single-crystalline Ga-doped SnO2 Nanowires and Self-organized SnO2/Ga2O3 Heterogeneous Microcomb Structures

Ga掺SnO2单晶纳米线和SnO2/Ga2O3自组织异质微米梳是通过简单的热蒸发沉淀法一步制得的,并通过X射线粉末衍射(XRD)、场激发扫描电子显微镜(FE-SEM)、透射电子显微镜(TEM)、X射线能量散射谱仪(EDS)、选区电子衍射谱(SAED)进行表征．从FE-SEM的图片上可以看出生成的产物具有纳米线和一种新的微米梳状形貌．XRD、SAED和EDS显示他们是单晶四角形的SnO2．产物的主干呈带状,纳米带阵列均匀的分布在主干的一侧或两侧．大量的Ga2O3纳米颗粒沉积在微米梳的表面．主干纳米带主要沿着[100]方向生长, 自组织的纳米带分支则在主干的(100)面上沿着[110]或者[110]方向生长．由于Ga的大量掺杂,光致发光谱的衍射峰发生红移并严重变宽．针对SnO2:Ga2O3异质微米梳的生长过程进行了解释,并讨论了实验条件对形貌的影响．     

铝电解中SnO2+Sb2O3+CuO惰性阳极的电流效率、腐蚀性及结构变化

系统研究了霍尔赫鲁特铝电解池中SnO₂基惰性阳极 (96%SnO₂+2%Sb₂O₃+2%CuO)的电流效率,腐蚀性以及结构变化. 评价了各种操作参数(温度、电流密度、阴阳两级的距离、冰晶石量比、Al₂O₃ 浓度和电解质组成)对电流效率和腐蚀性的影响.     

Multiplication of electronic excitations in nanophosphors Lu2O3:Eu and Lu2O3:Tb

Luminescence properties of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanocrystalline powders with the particle size varying from 46 to 6 nm were studied under excitation by synchrotron radiation in the photon energy range (up to ∼22.5 eV) covering the region where the processes of multiplication of electronic excitation occur. It was found that the excitation spectra of Tb³⁺ emission from all Lu₂O₃:Tb³⁺ nanopowders have similar behavior, whereas the shape of the excitation spectra of Eu³⁺ emission from Lu₂O₃:Eu³⁺ nanopowders strongly depends on the particle size. The difference in the behavior of Lu₂O₃:Eu³⁺ and Lu₂O₃:Tb³⁺ nanophosphor systems was explained by different mechanisms of the energy transfer from the host to Eu³⁺ or Tb³⁺ ions (either the hole or electron recombination mechanism, respectively), which are differently influenced by losses of electronic excitations near the particle surface.     

Influence of Si substrate preparation on surface chemistry and morphology of L-CVD SnO2 thin films studied by XPS and AFM

Results of experimental studies of the influence of substrate preparation on the surface chemistry and surface morphology of the laser-assisted chemical vapour deposition (L-CVD) SnO₂ thin films are presented in this paper. The native Si(1 0 0) substrate cleaned by UHV thermal annealing (TA) as well as thermally oxidized Si(1 0 0) substrate cleaned by ion bombardment (IBA) have been used as the substrates. X-ray photoemission spectroscopy (XPS) has been used for the control of surface chemistry of the substrates as well as of deposited films. Atomic force microscopy (AFM) has been used to control the surface morphology of the L-CVD SnO₂ thin films deposited on differently prepared substrates. Our XPS shows that the L-CVD SnO₂ thin films deposited on thermally oxidized Si(1 0 0) substrate after cleaning with ion bombardment exhibit the same stoichiometry, i.e. ratio [O]/[Sn] = 1.30 as that of the layers deposited on Si(1 0 0) substrate previously cleaned by UHV prolonged heating. AFM shows that L-CVD SnO₂ thin films deposited on thermally oxidized Si(1 0 0) substrate after cleaning with ion bombardment exhibit evidently increasing rough surface topography with respect to roughness, grain size range and maximum grain height as the L-CVD SnO₂ thin films deposited on atomically clean Si substrate at the same surface chemistry (nonstoichiometry) reflect the higher substrate roughness after cleaning with ion bombardment.     

Ce:Lu2Si2O7闪烁晶体的结构和光谱特性

采用中频感应提拉法生长出Ce:Lu₂Si₂O₇（Ce:LPS） 晶体. 通过x射线粉 末衍射分析，晶体结构属单斜晶系的C2/m空间群. 光学显微镜下可观测到晶体的（110 ）解理. 在室温下测试了Ce:LPS晶体的吸收光谱、激发光谱和发射光谱. 结果表明，Ce:LPS 晶体的吸收峰只有两个，分别位于302和349 nm，且与激发峰的位置一致，归因于Ce³⁺ 的4f¹→5d¹跃迁的特征吸收所致. 发射光谱具有Ce^{3+< /sup>典型的双峰特征 ，经Gaussian多峰值拟合，带状谱是由384和407 nm两个发射峰叠加而成，且后者的强度明 显高于前者. 关键词： 2Si₂O₇')" href="#">Ce:Lu₂Si₂O₇ 提拉法 晶体结构 光学 特性}     

Rational synthesis of α-MnO2 and γ-Mn2O3 nanowires with the electrochemical characterization of α-MnO2 nanowires for supercapacitor

An acidification-hydrothermal method was developed to synthesize α-MnO₂ nanowires, which was subsequently treated with ethanol, resulting in γ-Mn₂O₃ nanowire bundles on a large scale. The electrochemical characterization was carried out by cyclic voltammetry, which indicated that the α-MnO₂ nanowires in 0.5 mol L⁻¹ Na₂SO₄ aqueous electrolyte was of an excellent electrode material for supercapacitor at the scan rate of 10 mV S⁻¹ in the range of 0.0-0.85 V.     

Immittance response of the SnO2-Bi2O3 based thick-films

The SnO₂-Bi₂O₃ based thick-film polycrystalline material is fabricated on alumina substrate via screen-printing technique. This material system is evaluated at various temperatures (35 °C≤T≤100 °C) using ac small-signal (immittance) measurements in the frequency range 10 Hz≤f≤10⁶ Hz. The simplistic analytical scenario for the immittance data employed the Cole-Cole empirical equation in conjunction with the estimation of the inspected input parameters. This is an alternate approach compared to the complex nonlinear least squares (CNLS) fitting procedure, and purely based on the appearance of the semicircular relaxation in the complex plane. It is found that the constituting components of the semicircular relaxation in the impedance plane are thermally activated indicating complexity in the grain boundary contributions despite the Debye and non-Debye relaxation responses. The possible degree of uniformity or non-uniformity in the grain boundary activity associated with its capacitance term observed via the Debye or non-Debye semicircular relaxation in the impedance (Z?) plane has been postulated.     

Structural and optical properties of nanoparticulate Y2O3:Eu2O3 made by microwave plasma synthesis

Nanoparticulate Y₂O₃:Eu₂O₃ with a small, uniform particle size and a well-defined composition was synthesized using a low temperature microwave plasma process. The structural evolution and the luminescence properties were studied in different states of annealing and Eu₂O₃ addition using X-ray diffraction, transmission electron microscopy, and UV-photoluminescence spectroscopy. As synthesized, the samples were amorphous and showed only weak luminescence. Subsequent annealing steps from 500°C to 800°C lead to the formation and growth of cubic Y₂O₃:Eu₂O₃ nanocrystals (5–20 nm) and a concomitant strong increase of the luminescence yield already at small grain sizes in the range of 10 nm. No self-quenching effects were observed up to 11 mol% Eu₂O ₃.     

Solution-combusting preparation of mono-dispersed Mn3O4 nanoparticles for electrochemical applications

Manganese oxide (Mn₃O₄) nanoparticles with average diameter of 15 nm were prepared using alcohol solution of manganese chloride as starting material via a facile solution-combusting method. The flame core zone was chosen to prepare mono-dispersed and high crystalline products, which were employed to modify glassy carbon electrode and detect dopamine via cyclic voltammetry. The results exhibited excellent electrochemical sensitivity. A linear relationship between the concentration of dopamine and its oxidation peak current was obtained by differential pulse voltammetry, which will find wide application in the biological detection.