Effects of current densities on the formation of LiCoO<Subscript>2</Subscript>/graphite lithium ion battery

The activation characteristics and the effects of current densities on the formation of a separate LiCoO₂ and graphite electrode were investigated and the behavior also was compared with that of the full LiCoO₂/graphite batteries using various electrochemical techniques. The results showed that the formation current densities obviously influenced the electrochemical impedance spectrum of Li/graphite, LiCoO₂/Li, and LiCoO₂/graphite cells. The electrolyte was reduced on the surface of graphite anode between 2.5 and 3.6 V to form a preliminary solid electrolyte interphase (SEI) film of anode during the formation of the LiCoO₂/graphite batteries. The electrolyte was oxidized from 3.95 V vs Li⁺/Li on the surface of LiCoO₂ to form a SEI film of cathode. A highly conducting SEI film could be formed gradually on the surface of graphite anode, whereas the SEI film of LiCoO₂ cathode had high resistance. The LiCoO₂ cathode could be activated completely at the first cycle, while the activation of the graphite anode needed several cycles. The columbic efficiency of the first cycle increased, but that of the second decreased with the increase in the formation current of LiCoO₂/graphite batteries. The formation current influenced the cycling performance of batteries, especially the high-temperature cycling performance. Therefore, the batteries should be activated with proper current densities to ensure an excellent formation of SEI film on the anode surface.     

Impedance study on the correlation between phase transition and electrochemical degradation of Si-based materials

In order to explain the relationship between physical change and electrochemical degradation of Co–Co₃O₄ coated Si, impedance spectroscopy on Co–Co₃O₄ coated Si was conducted at various states during charge or discharge. Nyquist plots during Li⁺ insertion (charge) showed a unique behavior that below 70 mV vs. Li/Li⁺, the more Li⁺’s were inserted into the electrode, the larger its comprehensive resistance was getting. During Li⁺ extraction (discharge), electrode resistance was decreased after going through 0.43 V vs Li/Li⁺. When these data were fitted with the ordinary equivalent circuit which is composed of electrolyte resistance, charge transfer resistance and contact resistance, there was an abrupt augmentation of charge transfer resistance below 70 mV vs. Li/Li⁺ during charge, whereas there was its drastic diminishment between 0.2 and 0.5 V vs. Li/Li⁺ during discharge. Because these potential regions are each related to amorphous Li_xSi-to-Li₁₅Si₄ transition and vice versa, it could be shown that the formation and decomposition of Li₁₅Si₄ is responsible for the electrochemical degradation of Co–Co₃O₄ coated Si.     

Intermediate phases during alkali metal intercalation in HfNCl

The mechanism of the chemical and electrochemical alkali metal intercalation reactions in β-HfNCl has been investigated through electrochemical potential spectroscopy (EPS), in-situ powder X-ray diffraction during electrochemical intercalation and room temperature chemical intercalation experiments. EPS experiments in lithium cells reveal the presence of a plateau, at 1.8 V vs. Li⁺/Li⁰ accounting for ca. 0.14 mol Li, that indicates the formation of a new intermediate phase, and then a gradual decrease of potential with composition that extends up to very high lithium contents (ca. 1.1 per formula), consistent with the formation of a solid solution. Sodium electrochemical intercalation experiments showed a relatively similar behaviour with a plateau at 1.4 V vs. Na⁺/Na⁰, corresponding to ca. 1.7 V vs. Li⁺/Li⁰. In-situ monitored powder X-ray diffraction electrochemical intercalation experiments showed that the electrolyte solvent (ethylene carbonate/dimethyl carbonate, EC/DMC or propylene carbonate, PC) co-intercalated with the alkaline atom. This leads to a large expansion of the interlayer spacing that reaches a value of 21.06 Å in the lithium co-intercalated phase with EC/DMC, Li_x(EC/DMC)_yHfNCl, and 22.01 Å in the sodium co-intercalated phase with PC, Na_x(PC)_yHfNCl. Chemical intercalation using naphthyl-sodium solutions in tetrahydrofuran (THF) leads to solvent-free, multiple-phase samples showing in different proportions the pristine and the superconducting stage 2 and stage 1 phases. The composition of the intercalated samples depends on the pristine sample, the concentration of the naphthyl-sodium solution, the ratio Na:HfNCl and the reaction time. Pristine samples exhibiting low lithium intercalation degree upon electrochemical reduction gave the second stage as the major phase when treated with short reaction times or using low Na:HfNCl ratios, coexisting either with the host or with the first stage phase, whereas stage 1 is obtained as the major phase from pristine samples showing high electrochemical capacities. The staging behaviour and the multiphase nature of these samples account for the wide superconducting transitions and the different critical temperatures observed in these superconductors.     

Synergistic effect of fluorinated solvent and Mg2+ enabling 4.6 V LiCoO2 performances

Increasing the charging cut-off potential of lithium cobalt oxide (LiCoO₂, LCO) can effectively improve the energy density of the lithium-ion batteries, which are the mainstream energy storage devices used in 3C electronic products. However, the continuous decomposition of the electrolyte and dissolution of Co from the electrode will occur at high-potential operation, which deteriorate the performances of LCO. Here, a cathode-electrolyte interface (CEI) layer containing MgF₂ is constructed to enhance the electrochemical stability of LCO at 4.6 V (vs. Li⁺/Li). The Mg²⁺ added to the cathode gradually releases into the electrolyte during cycling, which forms a stable MgF₂-rich protective layer. In addition, 1,1,2,2-tetrafluoroethyl-2,2,3,3-tetrafluoropropylether (TTE) is added to the electrolyte acting as a F source to increase the content of MgF₂ in the CEI layer. The MgF₂-rich CEI layer effectively suppresses the decomposition of electrolyte components and the dissolution of Co of LCO, which makes the Li||LiCoO₂ (Li||LCO) cell cycled stably at 3∼4.6 V (vs. Li⁺/Li) in 200 cycles with a retention of 83.9%.     

Spectroelectrochemical studies on highly polarized LiCoO2 electrode in organic solutions

In situ Raman spectroscopy was conducted on thin film electrodes of pure LiCoO₂ in order to observe the nature of the changes in interfacial structure between LiCoO₂ and organic solutions (propylene carbonate and ethylene carbonate containing 1 M LiClO₄) when LiCoO₂ is scanned up to highly anodic potentials (∼5.0 V Li⁺/Li). Raman spectra and cyclic voltammograms were recorded simultaneously during the potential scan. We observed a sudden increase in the background signals of the Raman spectra at potentials more positive than 4.7 V. The increased background did not change after potential cycling. The change was irreversible, indicating that surface film formation occurred at positive potentials. As organic compounds fluoresce by visible light, the increased background is ascribed to the formation of a film on the LiCoO₂ electrode surface in organic solutions.     

Enhanced overcharge behavior and thermal stability of commercial LiCoO2 by coating with a novel material

Commercial LiCoO₂ has been modified with MnSiO₄ as a novel coating material. The structures, morphologies, overcharge behaviors and thermal stabilities of the pristine and MnSiO₄-coated LiCoO₂ materials were studied. The MnSiO₄-coated LiCoO₂ had initial discharge specific capacities of 181.1 and 232.2 mAh g⁻¹ within the potential ranges 2.75–4.5 and 2.75–4.7 V (vs. Li⁺/Li), respectively. It was found that the overcharge tolerance of the coated cathode was significantly better than that of the pristine LiCoO₂ under the same conditions – the discharge specific capacities of the coated cathode at upper charge cutoff voltages of 4.5 and 4.7 V were as high as 168.7 and 154.3 mAh g⁻¹, respectively, after 50 cycles. Moreover, DSC showed that the coated LiCoO₂ had a higher thermal stability than the pristine LiCoO₂.     

Monitoring electrode/electrolyte interfaces of Li-ion batteries under working conditions: A surface-enhanced Raman spectroscopic study on LiCoO2 composite cathodes

Lithium-ion batteries are commonly used for electrical energy storage in portable devices and are promising systems for large-scale energy storage. However, their application is still limited due to electrode degradation and stability issues. To enhance the fundamental understanding of electrode degradation, we report on the Raman spectroscopic characterization of LiCoO₂ cathode materials of working Li-ion batteries. To facilitate the spectroscopic analysis of the solid electrolyte interface (SEI), we apply in situ surface-enhanced Raman spectroscopy under battery working conditions by using Au nanoparticles coated with a thin SiO₂ layer (Au@SiO₂). We observe a surface-enhanced Raman signal of Li₂CO₃ at 1090 cm⁻¹ during electrochemical cycling as an intermediate. Its formation/decomposition highlights the role of Li₂CO₃ as a component of the SEI on LiCoO₂ composite cathodes. Our results demonstrate the potential of Raman spectroscopy to monitor electrode/electrolyte interfaces of lithium-ion batteries under working conditions thus allowing relations between electrochemical performance and structural changes to be established.     

Remarkably improved cycling stability of 3D porous Cu–Sn anode for lithium-ion full cells by adjusting working voltage range

Numerous studies confirm that three dimensional porous Cu–Sn (3DP Cu–Sn) anode possesses good application prospect in light of its desirable electrochemical performance on lithium ion half cells, but there are a few related systematic researches on lithium ion full cells until now, which is indispensable before its commercialization. Herein, the effects of galvanostatic charge-discharge voltage range on the cycling stability of 3DP Cu–Sn anode for lithium ion full cells are investigated systematically. The results show that the suitable charge-discharge voltage range plays a key role in improving the reversible capacity and cycling stability of the 3DP Cu–Sn||LiCoO₂ full cell, which is closely related to maintaining the electrode structure stable by controlling the amount of Li⁺ extracted and inserted. Especially, in the voltage range of 1.2–3.9 ​V, the full cell exhibits remarkably improved electrochemical properties with the high initial reversible capacity of 2.71 ​mAh cm⁻² and 71.95% capacity retention upon 80 cycles. We believe that this work can provide a significant reference for the practical application of porous Sn-based anodes.     

Carboxylic and sulfonic N-substituted naphthalene diimide salts as highly stable non-polymeric organic electrodes for lithium batteries

Two N-substituted naphthalene tetracarboxylic diimide (NTCDI) ionic compounds, carboxylic and sulfonic sodium salts, were prepared and used as positive electrode active materials in lithium-half cells. The aim of this investigation was to assess the solubility-suppressing effect of two different negatively charged substituent groups on a redox-active organic backbone using a carbonate-based liquid electrolyte. NTCDI derivatives were obtained in high yields from reaction of naphthalene tetracarboxylic dianhydride with neutralized glycine or with neutralized taurine. They were mixed with carbon black and cycled in galvanostatic mode against lithium metal using 1 M LiPF₆ EC/DMC liquid electrolyte. These two NTCDI derivatives exhibit a quite stable electrochemical activity upon cycling at an average potential of 2.3 V vs. Li⁺/Li⁰ giving rise to specific capacity values of 147 mAh·g^− 1 and 113 mAh·g^− 1 for the dicarboxylate and the disulfonate derivative, respectively. This study clearly supports the useful effect of such grafted permanent charges as a general rule on the electrochemical stability of crystallized organic materials based on the assembly of small redox-active units.     

Electrochemical behavior and stability of Li4Ti5O12 in a broad voltage window

Electrochemical behavior and stability of spinel Li₄Ti₅O₁₂ are investigated in a broad voltage window (0.0–5.0 V vs. Li/Li⁺). The voltage profile of the Li₄Ti₅O₁₂ electrode shows a plateau region at 1.55 V and two sloped regions below 1.55 V when the electrode is cycled between 0.0 and 2.0 V. It is found that Li₄Ti₅O₁₂ maintains high lithium storage characteristic with the increase of the current density. Moreover, Li₄Ti₅O₁₂ shows excellent rate performance in 0.0–2.0 V and good cyclic performances in 0.0–4.0 and 1.0–5.0 V. Besides, the crystal structure is kept when it is cycled between 0.0 and 5.0 V.     

Polymer/colloid dual-phase electrolyte membrane for rechargeable lithium batteries

In this work, a polymer/ceramic phase-separation porous membrane is first prepared from polyvinyl alcohol–polyacrylonitrile water emulsion mixed with fumed nano-SiO₂ particles by the phase inversion method. This porous membrane is then wetted by a non-aqueous Li–salt liquid electrolyte to form the polymer/colloid dual-phase electrolyte membrane. Compared to the liquid electrolyte in conventional polyolefin separator, the obtained electrolyte membrane has superior properties in high ionic conductivity (1.9 mS?cm^?1 at 30 °C), high Li⁺ transference number (0.41), high electrochemical stability (extended up to 5.0 V versus Li⁺/Li on stainless steel electrode), and good interfacial stability with lithium metal. The test cell of Li/LiCoO₂ with the electrolyte membrane as separator also shows high-rate capability and excellent cycle performance. The polymer/colloid dual-phase electrolyte membrane shows promise for application in rechargeable lithium batteries.     

Electro‐oxidation and reduction of H2 on platinum studied by scanning electrochemical microscopy for the purpose of local detection of H2 evolution

Electrochemical detection of H₂ using scanning electrochemical microscopy (SECM) has shown to hold great promise as a sensitive characterization method with high spatial resolution for active surfaces generating H₂. Herein, the factors contributing to the current that is measured by SECM in generation/collection mode for H₂ detection are studied. In particular, the concentration gradient of H₂ at the substrate, the H₂/H⁺ recycling between the SECM tip and substrate and hemispherical profile of H₂ diffusion has been discussed. It was postulated that H₂/H⁺ recycling plays a dominant role in the oxidative current measured in generation/collection mode of SECM when the microelectrode is positioned in close vicinity of substrate. Copyright © 2015 John Wiley & Sons, Ltd.     

LiCoO<Subscript>2</Subscript> electrode/electrolyte interface of Li-ion batteries investigated by electrochemical impedance spectroscopy

The storage behavior and the first delithiation of LiCoO₂ electrode in 1 mol/L LiPF₆-EC:DMC:DEC electrolyte were investigated by electrochemical impedance spectroscopy (EIS). It has found that, along with the increase of storage time, the thickness of SEI film increases, and some organic carbonate lithium compounds are formed due to spontaneous reactions occurring between the LiCoO₂ electrode and the electrolyte. When electrode potential is changed from 3.8 to 3.95 V, the reversible breakdown of the resistive SEI film occurs, which is attributed to the reversible dissolution of the SEI film component. With the increase of electrode potential, the thickness of SEI film increases rapidly above 4.2 V, due to overcharge reactions. The inductive loop observed in impedance spectra of the LiCoO₂ electrode in Li/LiCoO₂ cells is attributed to the formation of a Li_1−x CoO₂/LiCoO₂ concentration cell. Moreover, it has been demonstrated that the lithium-ion insertion-deinsertion in LiCoO₂ hosts can be well described by both Langmuir and Frumkin insertion isotherms, and the symmetry factor of charge transfer has been evaluated at 0.5. Supported by the Special Funds for Major State Basic Research Project of China (Grant No. 2002CB211804)     

Electrolytic molybdenum sulfides for thin-layer lithium power sources

The active molybdenum sulfide compound Mo₂S₃, which should be considered as a cathode material for thin-layer rechargeable power source, has been produced by electrolysis. Using impedance spectroscopy and potential relaxation method after current interruption, the kinetic parameters of lithium intercalation in electrolytic Mo₂S₃ have been obtained. Activation energy of Li⁺ migration in electrolyte (13.76 kJ/mol), charge transfer through the Mo₂S₃ electrode/electrolyte interface (38.8 kJ/mol), and Li⁺ diffusion in a solid phase (57.3 kJ/mol) have also been established. Taking into account the coefficient data of charge mass transfer in a solid phase and the reaction rate coefficient of charge transfer through the interface electrode/electrolyte within the temperature range 20–50 °C, the stage of Li⁺ transfer in a solid phase has been determined as a limiting stage for lithium intercalation in electrolytic molybdenum sulfide Mo₂S₃.     

An aqueous rechargeable lithium battery based on doping and intercalation mechanisms

An aqueous rechargeable lithium battery (ARLB) using an electroactive polymer, polypyrrole (PPy), as a negative electrode; a lithium ion intercalation compound LiCoO₂ as a positive electrode; and Li₂SO₄ aqueous solution as an electrolyte and its working mechanism are described. The charge/discharge process is associated with the doping/un-doping of anions at the negative electrode and intercalation/deintercalation of lithium ions at the positive electrode. The average output voltage of the PPy//LiCoO₂ battery is about 0.85 V. This battery exhibits excellent cycling performance. This new technology solves the major problem of poor cycling life of ARLBs and will provide a new strategy to explore advanced energy storage and conversion systems.     

Fabrication of Active Horseradish Peroxidase Micropatterns with a High Resolution by Scanning Electrochemical Microscopy

We used a new reactive species OH^? to fabricate active horseradish peroxidase (HRP) micropatterns with a high resolution by scanning electrochemical microscopy (SECM) coupled with a carbon fiber disk electrode as the SECM tip. In this method, except for active HRP micropatterns predesigned other regions on a HRP‐immobilized substrate were deactivated by OH^? generated at the tip held at ?1.7 V in 1.0 mol/L KCl containing 2.0×10^?3 mol/L benzoquinone (BQ) (pH 8.0). The feedback mode of SECM with a tip potential of ?0.2 V was used to characterize the active HRP micropatterns in 1.0 mol/L KCl containing 2.0×10^?3 mol/L BQ and 2.0×10^?3 mol/L H₂O₂.     

Improving the cycling performance,rate capacity,and thermal stability of LiCoO<Subscript>2</Subscript> by doping high-valence ions into the Li<Superscript>+</Superscript> site

The poor rate performance and low discharge capacity of LiCoO₂ limit its applications. Therefore, in this work, we synthesized Li_1-xM_xCoO₂ (M = Na, Zr, Nb) via solid-phase synthesis to improve its properties. X-ray diffraction (XRD) results suggest that the doping elements were successfully doped into LiCoO₂. The electrochemical properties showed that the samples doped with the high-valence elements Zr and Nb had a higher capacity, better cycle stability, and better rate performance than those doped with the low-valence element Na. In particular, the capacity retention of LiCoO₂, Li_0.97Na_0.03CoO₂, Li_0.99Zr_0.01CoO₂, and Li_0.99Nb_0.01CoO₂ was 68, 42, 85, and 87%, respectively, after 80 cycles at a rate of 10 C at 55 °C. However, doping of Zr and Nb into the Li⁺ site of LiCoO₂ will reduce the content of Li⁺. And, less Li⁺ extracted in the cathode material resulting in low discharge capacity under low current density. The larger radius of Na⁺ is incorporated into the Li slab and enlarged the interlayer spacing of the (003) plane. The larger (003) interplanar spacing can significantly facilitate the lithium diffusion and is also favorable to the rate capability. The differential scanning calorimetry (DSC) and thermogravimetric (TG) analysis results demonstrated that the Zr-doped and Nb-doped LiCoO₂ had a higher thermal stability in the charged state than the Na-doped LiCoO₂. Additionally, the resistances of the Zr-doped and Nb-doped electrodes were much lower than that of the undoped electrode. Our research results indicate that doping with high-valence elements is a very effective strategy for optimizing the electrochemical performance of LiCoO₂ and that this method can also be extended to other cathode materials.

Open image in new window

Graphical abstract ?

     

Short-term influence of interfering ion activity change on ion-selective micropipette electrode potential; another factor that can affect the time needed for imaging in potentiometric SECM

The applicability of ion-selective microelectrodes (ISME) in scanning electrochemical microscopy (SECM) in the presence of potentially interfering ions is investigated. Decreasing the time needed for potentiometric SECM imaging is a key aim. It is generally accepted that the long response time of potentiometric cells with high impedance microelectrodes limits the imaging speed that can be obtained without distortion. In this study we show that a change in the activity of interfering ions can result in a short-term electrode potential transient that should be taken into consideration in parameter setting for SECM measurements. The activity step method was employed, using NH₄⁺-ion-measuring micropipettes. Solutions containing equal concentrations of NH₄⁺ ions with or without K⁺ ions were rapidly introduced and the short-term change in electrode potential was recorded. Rapid transient potential signals appeared following the K⁺ activity step in the range where the interfering K⁺ did not affect the long-term electrode potential. The possible influence of this on SECM applications is discussed.     

Investigation of electrochemical reactions in the solid state cell Cu/RbCu4Cl3I2/C

Using experimental potential values for a vitreous carbon electrode in contact with the RbCu₄Cl₃I₂ solid electrolyte, the concentration of Cu²⁺ ions in the electrolyte was determined. At 0.5 V, the concentration of Cu²⁺ was 1.25×10¹⁸ cm^–3. The estimated values of the Cu²⁺ ion concentration in RbCu₄Cl₃I₂ (0.8%) and the potential of the vitreous carbon electrode after electrochemical decomposition of RbCu₄Cl₃I₂ (0.606 V) correspond to experimental values of 2% and 0.58 V, respectively. This demonstrates the adequacy of the model describing the electrode potential of Cu²⁺ as a function of the concentration in RbCu₄Cl₃I₂. When the C/RbCu₄Cl₃I₂ interface was polarized, the diffusion coefficient of Cu²⁺ was 1.5×10^–8 cm² s^–1. Investigations of the interface between the copper electrode and RbCu₄Cl₃I₂ were carried out by galvanostatic and potentiostatic methods. A 1-μm layer of cuprous oxide, Cu₂O, was discovered on the interface of the copper electrode with RbCu₄Cl₃I₂. This layer blocks the course of the electrochemical reaction Cu⁰–e^–⇌Cu⁺ with participation of copper metal. The copper electrode behaves as an inert redox electrode at low overvoltages. In this case, at the Cu₂O/RbCu₄Cl₃I₂ interface an electrochemical reaction with Cu²⁺ ion participation, Cu⁺–e^–⇌Cu²⁺, takes place. The results suggest that the reaction rate is limited by slowing the Cu²⁺ diffusion in RbCu₄Cl₃I₂. The initial Cu²⁺ ion concentration in the electrolyte near this interface is about 1.4×10¹⁷ cm^–3. The exchange current density is about (4±2)×10^–6 A cm^–2. At potentials ϕ>8–10 mV, an electrical breakdown of the Cu₂O layer takes place, allowing copper metal to ionize to Cu⁺. We suggest that at 10 mV<ϕ<100 mV the rate of this reaction is limited by the formation and growth of copper nuclei and at ϕ>120 mV the reaction rate is limited by charge transfer. Electronic Publication