Dual-wavelength high-power Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating

We report a high-power dual-wavelength Yb-doped double-clad fiber laser based on a few-mode fiber Bragg grating (FMFBG). The FMFBG was fabricated by using a piece of fiber in a length of fiber with a cutoff wavelength of 1225 nm, which supported two modes at 1060 nm. The laser was pumped by a fiber pigtailed laser diode working at 915 nm. Single-wavelength, dual-wavelength and triple-wavelength laser oscillations were observed when the fiber laser operated under different low pump powers. However, stable dual-wavelength operation was achieved at higher pump power of 3.9 W and remained unchanged until the output power reached 5.67 W under the maximum available pump power of 10.7 W. The laser wavelengths were centered at 1059.12 and 1060.80 nm with a full-width at half-maximum of 37 and 43 pm, respectively. The signal-to-noise-ratio was greater than 50 dB and the beam quality factor (M²) was about 1.9.     

High birefringence and low loss circular air-holes photonic crystal fiber using complex unit cells in cladding

We propose a high birefringence and low loss index-guiding photonic crystal fiber (PCF) using the complex unit cells in cladding by the finite-element method. Results show that the birefringence and confinement loss in such PCF fiber is determined not only by the whole cladding asymmetry but also the shape of the PCF core. The maximal modal birefringence and lowest confinement loss of our proposed structures at the excitation wavelength of λ = 1550 nm can be achieved at 8.7 × 10⁻³ and 5.27 × 10⁻⁵ dB/km, respectively.     

Filtering characteristics of film-coated long-period fiber gratings operating at the phase-matching turning point

We present novel filtering characteristics of film-coated long-period fiber gratings (LPFGs) operating at phase-matching turning point (PMTP). The 3 dB bandwidth of a single broadband dip depends greatly on the film refractive index and thickness. A π-phase-shift in the grating center produces two band-rejection peaks between which the separation reaches 375 nm. This separation increases with the number M (M > 1) of π-phase-shifts that divide the LPFG uniformly. The central loss is constant at zero for odd M, whereas decreases with M for even M. Increasing film thickness and refractive index result in blue shifts of the dual peaks and enlarge the separations, which exhibits excellent tunabilities.     

Phase-matched third-harmonic UV generation using low-order modes in a glass micro-fiber

We observe phase-matched third-harmonic generation at 355 nm in a low-order mode of a sub-micron diameter glass fiber. The third-harmonic signal exhibits a sharp resonance for a fiber diameter d = 0.49 ± 0.02 μm, in excellent agreement with the value d = 0.506 μm predicted by theory. The third-harmonic conversion efficiency is 2 × 10⁻⁶, and is limited by the pump power (1 kW) and effective fiber length (100 μm).     

Broadband Er-Yb co-doped superfluorescent fiber source

In this paper, extensive experimental results on broad-band double cladding Er³⁺-Yb³⁺ co-doped superfluorescent fiber sources (SFSs), characterizing their output power, mean wavelength, and bandwidth (BW) stability with variations of pump power, pump wavelength, and fiber temperature, have been reported. For a 55-cm fiber, SFS power from 3.7755 (maximum BW condition of more than 80 nm) to 9.1837 mW (maximum power condition, BW is about 34 nm) has been achieved. The SFS mean wavelength dependence on pump wavelength is highly pump temperature sensitive, and can be reduced to zero in a chosen pump temperature field. The intrinsic variation of the SFS mean wavelength λ_m with fiber temperature is also measured, and a linear variation from 15 to 45 °C with a slop of −0.053 nm/°C for L_f = 100 cm and −0.04 nm/°C for L_f = 55 cm is found.     

High power single transverse mode operation of a tapered large-mode-area fiber laser

To get high output power with good beam quality, a tapered section is introduced to large-mode-area (LMA) Yb-doped fiber laser. Output characteristics of the fiber laser without tapered section and with tapered section are compared experimentally. When the launched pump power is 119.1 W, 77.9 W with M² 3.08 and 56.4 W with M² 1.14 can be obtained, respectively. The corresponding slope efficiencies are 71.8% and 54.1%, respectively. Although output power of the tapered fiber laser has 30.6% penalty, brightness of it is as much as 5.28 times of the fiber laser without tapered section. Moreover, spectra of them are measured. It is found that tapered section makes lasing wavelength of the fiber laser shorter.     

Design of single polarization single mode dispersion compensating photonic crystal fiber

In this paper, we present a photonic crystal fiber based on hexagonal structure for improved negative dispersion as well as high birefringence in the telecom wavelength bands. It is demonstrated that it is possible to obtain negative dispersion coefficient of −712 ps/(nm km) and relative dispersion slope (RDS) perfectly match to that of single mode fiber (SMF) of about 0.0036 nm⁻¹ at the operating wavelength 1550 nm. The proposed fiber exhibits high birefringence of the order 2.11 × 10⁻² with nonlinear coefficient about 57.57 W⁻¹ km⁻¹ at 1550 nm. Moreover, it is confirmed that the designed fiber successfully operates as a single mode in the entire band of interest.     

Characteristics of low noise hybrid fiber amplifier

The characteristics of hybrid fiber amplifier (HFA) are investigated. HFA is composed of three stages: short-length EDFA pre-stage, DCF Raman amplifier, and power boosting EDFA. HFA has low noise figure, high output power, and also wide input power dynamic range. Gain control method of HFA is presented experimentally, and the transient gain excursion is suppressed to less than 0.5 dB at 3 dB channel add-drop. HFA can be used as line amplifier in optical transmission link even combined with distributed Raman amplifier due to wide input power dynamic range. The transmission performance of HFA is better than EDFA by more than 1.0 dB of Q-factor in 720 km SMF transmission.     

All-optical continuously tunable delay with a high linear-chirp-rate fiber Bragg grating based on four-wave mixing in a highly-nonlinear photonic crystal fiber

A scheme for hi-fi all-optical continuously tunable delay is proposed. The signal wavelength is converted to a desired idler wavelength and converted back after being delayed by a high linear-chirp-rate (HLCR) fiber Bragg grating (FBG) based on four-wave mixing (FWM) in a highly-nonlinear photonic crystal fiber (HN-PCF). In our experiment, 400 ps (more than 8 full width of half maximum, FWHM) tunable delay is achieved for a 10 GHz clock pulse with relative pulse width broaden ratio (RPWBR) of 2.08%. The power penalty is only 0.3 dB at 10⁻⁹ BER for a 10 Gb/s 2³¹−1 pseudo random bit sequence (PRBS) data.     

Evaluation of quenching effects on silica-based erbium doped fiber micro-ring lasers

While micro-ring lasers is a step forward for the miniaturization of fiber lasers, up-conversion quenching due to ion energy transfer may limit the device size and deteriorate system performance. The effect of Er³⁺ concentration quenching on the characteristics of silica-based Er-doped fiber (EDF) micro-ring laser was investigated. In particular, the dependence on Er³⁺ concentration and laser size of threshold pump power and quantum efficiency is discussed. To achieve high laser efficiency, it was found that ring diameter has to be ∼150 μm with ∼5 wt.% erbium concentration. The threshold value is increased by a factor of 340, for such laser characteristics compared with threshold power when up-conversion is not considered. Moreover, we show that detrimental effect due to up-conversion quenching can be reduced by careful micro-ring laser design.     

Optimal design of 32 channels spectrum slicing WDM for optical fiber access network system

In this article, the spectrum sliced dense wavelength division multiplexed passive optical network (SS-DWDM–PON) has been investigated as a power efficient and cost effective solution for optical access networks. In this work an AWG demultiplexer is used to operate as slicing system. The high speed SS-DWDM system has been realized and investigated for 32 channels with data rate up to 3 Gb/s using broadband ASE source (LED). The 3 Gb/s signals both non-return-to-zero (NRZ) and return-to-zero (RZ) were demonstrated in 40 km optical fiber link with BER < 10⁻¹². The results obtained here demonstrate that SS-DWDM is well suited for Fiber-to-the-Home (FTTH) network.     

Design and characterization of single mode circular photonic crystal fiber for broadband dispersion compensation

In this paper, we present a single mode circular photonic crystal fiber (C-PCF) for broadband dispersion compensation covering 1400 to 1610 nm wavelength band over the telecommunication windows. Investigations of guiding properties are carried out using finite element method (FEM) with circular perfectly matched layer boundary condition. Numerical study reveals that a negative dispersion coefficient of about −386.57 to −971.44 ps/(nm km) is possible to obtain over the wavelength ranging from 1400 to 1610 nm with a relative dispersion slope (RDS) of about 0.0036 nm⁻¹ at 1550 nm wavelength. In addition, the single mode behaviour of C-PCF is demonstrated by employing V parameter. According to simulation, it is found that the proposed C-PCF acts as a single mode fiber within 1340 to 1640 nm wavelength. Moreover, effective dispersion, relative dispersion slope, birefringence and confinement loss are also presented and discussed.     

Designing of endlessly single mode polarization maintaining highly birefringent nonlinear micro-structure fiber at telecommunication window by FV-FEM

An endlessly single mode highly polarization maintaining nonlinear microstructure fiber at telecommunication window is reported via full-vector finite element method. By taking three ring hexagonal PCF with suitable fiber parameter such as air hole diameter in cladding region d = 0.8 μm, pitch 2.3 μm and introducing four symmetrical large air holes near core region d′ = 2 μm, single mode (V_eff ≤ π), small effective mode area 2.7 μm², nonlinear co-efficient 44.39 W⁻¹ km⁻¹, high phase birefringence of the order of 10⁻³ and group birefringence of the order of 10⁻⁴ with beat length 0.3 μm at wavelength 1.55 μm are achieved.     

Add/drop applications in fiber ring networks based on a reconfigurable optical add/drop multiplexer in a re-circulating loop

A periodic add/drop system in a fiber ring network was investigated using a reconfigurable optical add/drop multiplexer (ROADM) in a re-circulating fiber loop. After seven cascaded add/drop nodes at every 150 km along the transmission, at bit error ratio (BER) equals to 10⁻⁹ and data rate of 10 Gbps, we observed a 2.5 dB power penalty for the passing through channels with 1050 km transmission distance, and 0.3 dB sensitivity penalty variation for the periodic add/drop channels at every 150 km, respectively.     

Optical sensing characteristics of the photonic crystal fiber filled with magnetic fluid

A novel photonic crystal fiber sensing theory filled with magnetic fluid is proposed based on the change of the MF refractive index under varied magnetic field. The magnetically induced tuning of the magnetic fluid filled PCF propagation properties were investigated by the full-vector finite element method with a perfectly matched layer. Theoretical calculations show that both the effective refractive index and the effective mode area increase vs. the increased magnetic field, and the PCF filled MF with larger d/Λ is more sensitive to magnetic field. When the wavelength λ = 1550 nm, the duty ratio d/Λ = 0.9, d/Λ = 0.6, the effective refractive indexes increase respectively from 1.598279 to 1.617572, from 1.61948 to 1.632484, and the effective mode areas increase respectively from 3.561115 μm² to 7.052360 μm², from 6.167494 μm² to 37.221998 μm² as the magnetic field changes from 25 Oe to 175 Oe. This scheme provides theoretical foundation to use magnetic field to control light in photonic crystal fiber and also offers a potential method for magnetic field sensing based on the TIR-PCF.     

Reconfigurable all-optical logic gate using four-wave mixing (FWM) in HNLF for NRZ-PolSK signal

We demonstrate a reconfigurable all-optical logic gate for NRZ-PolSK signal based on FWM in a highly nonlinear fiber at 10 Gb/s. Half subtracter, XOR, AB?, āB or XNOR, AND, and NOR logic gates can be implemented simultaneously. The input power for the HNLF is optimized to be as low as about 15.2 dBm and the high Q factors above 8 dB for eye diagrams are achieved. Experimental results show Q factors of AB?, āB, AND, and NOR were higher than those of XOR, and XNOR. Error-free operation is achieved experimentally for 10 Gb/s 2⁷-1 pseudorandom bit sequence (PRBS) data. Power penalties for the logic gate are less than 3 dB. Simulation analysis about the wavelength characteristic for all logic gates is given and it predicts that the reconfigurable logic gate can realize error-free operation when the wavelength separation is less than 5 nm.     

22 dB all-fiber green amplifier using Er-doped fluoride fiber

We demonstrate a 22 dB all-fiber amplifier at 546 nm using Er³⁺-doped fluoride fiber by forward upconversion pumping of a 974 nm laser diode. The gain saturation effects and the power conversion efficiency of this amplifier are investigated in detail based on gain characteristics and numerical simulations.     

Wide band gain flattening Yb-doped fiber amplifier

The gain flattening of Yb³⁺-doped fiber amplifier of 1053 nm band has been realized in experiment using three cascade 1 × 2 fused tapered fiber coupler. The gain flattening band is about 20 nm with less than 1 dB power fluctuation around 1053 nm, which is agree with our numerical stimulation results very well.     

Noise figure and gain temperature dependent of praseodymium-doped fiber amplifier by using rate equations

A theoretical study of the temperature dependent noise effects of praseodymium-doped fiber amplifiers (PEDFAs) has been examined. The Pr³⁺-doped ZBLAN fiber amplifier pumped at 1017 nm and Pr³⁺-doped GeGa-sulfied fiber amplifier pumped at 1028 nm are chosen. The temperature-dependent rate and propagation equation related to four-level system consideration which is based on the population difference among amplification levels has been used. The population difference depends on pump and signal powers, Boltzman factor K_B, cross-sections, noise figure (NF) and Pr³⁺ concentration. The numerical results obtained over the temperature range from −20 °C to + 60 °C are used to present an analytical expression for the signal gain and noise figure effects in PDFAs length and noise figure with input pump power. The amplified spontaneous emission (ASE) has been taken into account.     

Optical fiber curvature sensor based on few mode fiber

An optical fiber curvature sensor based on interference between LP₀₁–LP₀₂ modes of a circularly symmetric few mode fiber (FMF) is presented. The device consists of two single-mode fiber and a 10-cm FMF. The two single-mode fiber is offset-spliced to each end of the FMF. When the optical fiber is kept straight and fixed, the interference pattern appears in the transmitted spectrum. As the fiber device is bent, the visibility of the interference fringes (at 1530 nm) decreases, reaching values close to 0.3. The dynamic range of the device can be tailored by the proper selection of the length of FMF. The relationship between the fringe visibility and the curvature is linear while the curvature is between 11 m⁻¹ and 16 m⁻¹. The result indicates that the compact sensor can be used in the measurement of large curvature, which is also important in structural health monitoring.