Calculation of crosstalk in the 8×10 Gbit/s OTDM system using SMZ switch

Optical time division multiplexing is an emerging and promising alternative for future high-speed photonic networks because of its ability to accommodate higher bit rate and flexible bandwidth. Symmetric Mach–Zehnder (SMZ) have been found to be the most suitable switching element than all the available de-multiplexing switches because of compact size, thermal stability, and low-power operation. In this paper, we simulate eight-channel OTDM systems (all-channel multiplexer and de-multiplexer (DEMUX)) with a Mach–Zehnder modulator and SMZ de-multiplexer to investigate the impact of control signal power and to calculate the crosstalk.     

Performance analysis of OTDM system in the presence of FEC using symmetric Mach-Zehnder switch

Optical time division multiplexing is an emerging and promising alternative for future high-speed photonic networks because of its ability to accommodate higher bit rate and flexible bandwidth. SMZ have been found to be the most suitable switching element than all the available de-multiplexing switches because of compact size, thermal stability, and low-power operation. In this paper, we simulate four channel OTDM systems (all-channel multiplexer and de-multiplexer) with a Mach-Zehnder modulator and an SMZ de-multiplexer to investigate the impact of FEC on the OTDM system. It is observed that the presence of FEC in OTDM transmission can greatly improve the system performance.     

光时分复用系统中单路时钟的提取

提出利用复用信号的时候不均匀性,采用主动光纤锁模激光器,直接从复用后的信号中提取出复用前的时钟光脉冲。考虑到电的时分复用与光的时分复用在机理上的一致性,故初步复用时分复用信号进行实验,成功地从时分复用信号中得到了复用前的时钟光脉冲。此处电的时分复用所得的结论适用于光的时分复用。     

The effects of power rippling on CO2 laser cutting

A power rippling method was proposed in this study to improve the cut edge quality by disturbing the natural frequency of the periodic striations in high power C0₂ laser cutting. A pilot study was also designed and set up to examine the power responsibility of the laser system, which is externally controlled by a modulated analogue signal from a signal generator. Several aspects were examined in this study. The effects of different power rippling frequencies on the cut surface roughness is the first such aspect, and the different power modulation depth on cut surface roughness is another. The power rippling shape is the third important parameter examined in this study. It was found that the amplitude and frequency of the striation pattern on the cut surface were significantly affected by the characteristics of the rippling power. Cutting quality can be significantly improved by rippling the laser power.     

Optical time division multiplexing at 160 Gbps using MZI switching

Many lower-speed data streams can be multiplexed into one high-speed stream by means of optical time division multiplexing (OTDM), such that each input channel transmits its data in an assigned time slot. The simulation is performed by a fast multiplexer switch (mux). The routing of different data streams at the end of the TDM link is performed by a demultiplexer switch (demux) and this demultiplexer is employed using MZI switch as it consists a semiconductor optical amplifier (SOA) and an optical coupler. In this paper four channel OTDM is simulated at 40 Gbit/s and further the impact of the signal power, pulse width and control signal power on BER is investigated.     

Optoelectronic properties of Cu1−xPtxFeO2 (0 ≤ x ≤ 0.05) delafossite for p-type transparent conducting oxide

The samples of Cu_1−xPt_xFeO₂ (0 ≤ x ≤ 0.05) delafossite have been synthesized by solid-state reaction method to investigate their optical and electrical properties. The properties of electrical resistivity and Seebeck coefficient were measured in the high temperature ranging from 300 to 960 K, and the Hall effect and the optical properties were measured at room temperature. The obtained results of Seebeck showed the samples are p-type conductor. The optical properties at room temperature exhibited the samples are transparent visible light material with optical direct gap 3.45 eV. The low electrical resistivity, hole mobility and carrier density at room temperature displayed value ranging from 0.29 to 0.08 Ω cm, 1.8 to 8.6 cm²/V s and 1.56 × 10¹⁸ to 4.04 × 10¹⁹ cm⁻³, respectively. The temperature range for transparent visible light is below 820 K because the direct energy gap contains value above 3.1 eV. Consequently, the Cu_1−xPt_xFeO₂ delafossite enhance performance for materials of p-type transparent conducting oxide (TCO) with low electrical resistivity.     

Ultrafast all-optical signal processing with Symmetric Mach–Zehnder type all-optical switches

We present Symmetric Mach–Zehnder (SMZ) type all-optical switches: an SMZ all-optical switch, a polarization-discriminating SMZ (PD-SMZ) all-optical switch, and a delayed interference signal wavelength converter (DISC). These switches are capable of ultrafast, low control power, and low chirp switching, which is not restricted by slow relaxation of highly efficient nonlinearities. High repetition operation unrestricted by slow relaxation is also possible for these switches. This is because of a push–pull modulation scheme or sometimes called a differential phase modulation scheme. These three devices are similar, but different in some important aspects, thus a comparison is made among the three. Then semiconductor optical amplifiers (SOAs) are discussed as a nonlinear phase shifter for these devices. Then, ultrafast all-optical signal processing using SOA based SMZs is demonstrated. Error-free demultiplexing from 168 to 10.5 Gbit/s is presented, in which a hybrid-integrated SMZ (HI-SMZ) is used as a demultiplexer. In pulse regeneration experiment, the signal pulses at 84 Gbit/s are regenerated by the PD-SMZ and the regenerated pulses are demultiplexed to 10.5 Gbit/s by the HI-SMZ to verify error-free operation. The retiming capability of this scheme is quantitatively demonstrated. Also presented is error-free all-optical wavelength conversion at 168 Gbit/s using the DISC. These results represent the fastest error-free operations reported to date in each category.     

DSB optical mm-wave with signal only on optical carrier generated by embedded LiNbO3 Mach-Zehnder modulator

We have investigated the generation of the 40-GHz double-sideband optical millimeter (mm)-wave with signal carried only by its optical carrier via an embedded LiNbO₃ Mach-Zehnder modulator (LN-MZM). Since the optical carrier and its two first-order sidebands are dominant and their powers are well balanced, the first-order harmonic in the photocurrent gets maximal. As the optical mm-wave signal is transmitted along the fiber, there is no code outline distortion because the signal is only modulated on the optical carrier. Although the first-order harmonic shows the periodical fading effect when the optical mm-wave signal is transmitted along the fiber, its degradation on the radio-over-fiber link can be avoided by adjusting the position of the fading nodes via varying the main MZM bias voltage, and the signal still keeps much good eye diagram even after 50-km fiber transmission. The experimental results prove our theory.     

Frequency Stabilization of Waveguide CO2 Laser by a Digital Technique

In this work we present a simple technique for laser frequency stabilization, based on Digital signal processing. The technique is used to stabilize a waveguide CO₂ laser of wide tunability by using three kinds of reference signals: the CO₂ laser ouptut power, an infrared absorption optoacoustic signal and the output power of a Far-Infrared optically pumped molecular laser.     

Construction of a photon drag detector for evaluating the performance of a CO2 laser amplifier

In this article, the construction of P-type germanium (Ge) photon drag detector which is used to characterize the gain and output powers of a 10 W CO₂ laser and a CO₂ laser amplifier is described. Gain and laser amplifier output power versus laser input power measurements collected at 4.7 mbar and 12.0 mbar amplifier tube pressures are discussed. Moreover, measurements relating the CO₂ laser output power to the laser tube discharge current are provided at 6.9 mbar and 7.3 mbar tube pressures.     

On the modelling of the power extraction problem from a gas-dynamic CO2 laser considering the variations of intensity

In this paper a new simple model for investigation of the power extraction process from a gas-dynamic laser (GDL) is presented. This analysis consists of a numerical solution of non-equilibrium supersonic flow in the laser cavity and, simultaneously, point-by-point numerical integration of the laser intensity in the beam direction. The simplest cavity, that is a Fabry-Perot with parallel mirrors, is used. This model gives the variation of intensity in the flow direction, without any specific assumptions. The behaviours of all interesting quantities are obtained and compared with other existing models.     

Error-free OTDM demultiplexer using the supercontinuum spectrum-slicing induced clock signal

We experimentally demonstrate an 80-Gb/s optical time-division multiplexing (OTDM) demultiplexing system based on the cross-phase modulation (XPM) effect in high-nonlinearity fibers. The message carried by OTDM signal is loaded onto the probe signal by sampling the OTDM packet with a 10-GHz stable and controllable clock pulse train. The clock signal with ~ 11 ps pulse width is achieved by employing supercontinuum spectrum-slicing technique, which is distinct from that based on mode-locked lasers. The demultiplexed signal is obtained by filtering out the XPM-induced spectral sidebands of the probe signal. The OTDM demultiplexer based on this novel technique shows excellent performances and contributes to a bit error rate of as low as 10⁻⁹.     

Demonstration of an 8×10-Gb/s OTDM system

An 8×10 Gb/s optical time-division-multiplexing (OTDM) system was demonstrated with an electroabsorption modulator (EAM) based short pulse generator followed by a two-stage nonlinear compression scheme which generated stable 10-GHz, 2-ps full-width at half-maximum (FWHM) pulse train, an optoelectronic oscillator (OEO) that extracted 10-GHz clock with a timing jitter of 300 fs from 80-Gb/s OTDM signal and a self cascaded EAM which produced a switching window of about 10 ps. A back-to-back error free demultiplexing experiment with a power penalty of 3.25 dB was carried out to verify the system performance.     

Magnetic properties and room-temperature magnetocaloric effect in the doped antipervoskite compounds Ga1−xAlxCMn3 (0≤x≤0.15)

We report the effects of Al doping on the structure, magnetic properties, and magnetocaloric effect of antiperovskite compounds Ga_1−xAl_xCMn₃ (0≤x≤0.15). Partial substitutions of Al for Ga enhance the Curie temperature (from 250 K for x=0.0 to 312 K for x=0.15) and the saturation magnetization. On increasing the doping level x, the maximum values of the magnetic entropy change (−ΔS_M) decreases while the temperature span of −ΔS_M vs. T plot broadens. Furthermore, the relative cooling power (RCP) is also studied. For 20 kOe, the RCP value tends to saturate at a high doping level (for x=0.12, 119 J/kg at 296 K). However, at 45 kOe, the RCP value increases quickly with increasing x (for x=0.15, 293 J/kg at 312 K). Considering the relatively large RCP and inexpensive raw materials, Ga_1−xAl_xCMn₃ may be alternative candidates for room-temperature magnetic refrigeration.     

Fermi edge singularity evidence from photoluminescence spectroscopy of AlGaAs/InGaAs/GaAs pseudomorphic HEMTs grown on (3 1 1)A GaAs substrates

InGaAs/AlGaAs/GaAs pseudomorphic high electron mobility transistor (P-HEMT) structures were grown by Molecular Beam Epitaxy (MBE) on (3 1 1)A GaAs substrates with different well widths, and studied by photoluminescence (PL) spectroscopy as a function of temperature and excitation density.The PL spectra are dominated by one or two spectral bands, corresponding, respectively, to one or two populated electron sub-bands in the InGaAs quantum well. An enhancement of PL intensity at the Fermi level energy (E_F) in the high-energy tail of the PL peak is clearly observed and associated with the Fermi edge singularity (FES). This is practically detected at the same energy for all samples, in contrast with energy transitions in the InGaAs channel, which are shifted to lower energy with increasing channel thickness. PL spectra at low temperature and low excitation density are used to optically determine the density of the two-dimensional electron gas (2DEG) in the InGaAs channel for different thicknesses. The results show an enhancement of the 2DEG density when the well width increases, in good agreement with our previous theoretical study.     

High-speed deposition of RE123 film with large current capacity by hot-wall type PLD system

We have studied a hot-wall heating system to produce GdBa₂Cu₃O_y (GdBCO) films with large critical currents (I_c) at a high production rate by a pulsed-laser-deposition (PLD) method. GdBCO films fabricated at a production rate of 30 m/h under the optimized conditions, especially a distance of 95 mm between the target and the substrate (T–S), exhibited high critical current densities (J_c) of about 3 MA/cm² and I_c over 300 A at a thickness of 1–2 μm. Furthermore, long GdBCO tapes prepared by repeated depositions at each tape-passing speed of 80 m/h showed uniform I_c distribution along the longitudinal direction, because the hot-wall system enabled to stabilize temperature within a few degrees at 800 °C. A 170 m long tape with I_c over 600 A was successfully fabricated at a production rate of 16 m/h using a laser power of 360 W.     

Phase transition in Pd<Subscript>40</Subscript>Ni<Subscript>10</Subscript>Cu<Subscript>30</Subscript>P<Subscript>20</Subscript> bulk metallic glass under HP &; HT

The phase transitions in Pd₄₀Ni₁₀Cu₃₀P₂₀ bulk metallic glass (BMG) have been studied under high pressure and high temperature (HP & HT) by X-ray diffaction measurements with synchrotron radiation source. We found that the BMG underwent a phase transitions of amorphous-crystalline-amorphous at 10 GPa upon heating. The parallel experiments were carried out at 7 GPa, while we did not observe the amorphous-crystalline-amorphous transitions by increasing temperature. Quenching the melted BMG at 7 GPa, it was found that the phase crystallized from the melt differed from the primary phase crystallized from the starting amorphous solid upon heating suggesting there existed a distinct mechanism in two cases.     

Third harmonic transmit phasing for SNR improvement in tissue harmonic imaging with Golay-encoded excitation

Background

Ultrasound tissue harmonic signal generally provides superior image quality as compared to the linear signal. However, since the generation of the tissue harmonic signal is based on finite amplitude distortion of the propagating waveform, the penetration and the sensitivity in tissue harmonic imaging are markedly limited because of the low signal-to-noise ratio (SNR).

Methods

The method of third harmonic (3f₀) transmit phasing can improve the tissue harmonic SNR by transmitting at both the fundamental (2.25 MHz) and the 3f₀ (6.75 MHz) frequencies to achieve mutual enhancement between the frequency-sum and the frequency-difference components of the second harmonic signal. To further increase the SNR without excessive transmit pressure, coded excitation can be incorporated in 3f₀ transmit phasing to boost the tissue harmonic generation.

Results

Our analyses indicate that the phase-encoded Golay excitation is suitable in 3f₀ transmit phasing due to its superior transmit bandwidth efficiency. The resultant frequency-sum and frequency-difference components of tissue harmonic signal can be simultaneously Golay-encoded for SNR improvement. The increase of the main-lobe signal with the Golay excitation in 3f₀ transmit phasing are consistent between the tissue harmonic measurements and the simulations. B-mode images of the speckle generating phantom also demonstrate the increases of tissue harmonic SNR for about 11 dB without noticeable compression artifacts.

Conclusion

For tissue harmonic imaging in combination with the 3f₀ transmit phasing method, the Golay excitation can provide further SNR improvement. Meanwhile, the axial resolution can be effectively restored by pulse compression while the lateral resolution remains unchanged.     

基于光注入Fabry-Perot半导体激光器实现同步全光分路时钟提取与波长转换

提出了一种利用Fabry-Perot（FP）半导体激光器同步提取波长转换的分路光时钟的新方法,并对该方法进行了数值模拟和实验验证.光注入半导体激光器会产生非线性单周期振荡特性,利用交叉增益调制效应及对单周期振荡的微波锁频效应,可从光时分复用信号中提取出波长转换的分路光时钟.采用一个FP半导体激光器作为全光分路时钟提取及波长转换器,数值模拟实现了从波长为1555 nm、速率为2×20 Gb/s的光时分复用信号中提取出波长转换为1550 nm、重复频率为20 GHz的分路光时钟,实验完成了从波长为155024 nm、重复频率为1236 GHz光脉冲信号中提取出相位噪声为-105 dBc/Hz的波长为154591 nm、重复频率618 GHz的分频光时钟.此外还详细研究了注入光功率、波长失谐、FP激光器偏置电流及纵模选择对光时钟提取的影响,实验结果和数值模拟结果符合.该方法在光时分复用混合波分复用通信系统中实现全光解复用及波长路由有着重要的应用价值. 关键词： 波长转换 时钟提取 光注入 非线性动力学     

Variable order spherical harmonic expansion scheme for the radiative transport equation using finite elements

We propose the P_N approximation based on a finite element framework for solving the radiative transport equation with optical tomography as the primary application area. The key idea is to employ a variable order spherical harmonic expansion for angular discretization based on the proximity to the source and the local scattering coefficient. The proposed scheme is shown to be computationally efficient compared to employing homogeneously high orders of expansion everywhere in the domain. In addition the numerical method is shown to accurately describe the void regions encountered in the forward modeling of real-life specimens such as infant brains. The accuracy of the method is demonstrated over three model problems where the P_N approximation is compared against Monte Carlo simulations and other state-of-the-art methods.