A least-squares method to cancel rigid body displacements in a hole drilling and DSPI system for measuring residual stresses

This paper presents the evaluation of a method to cancel rigid body displacements that can be introduced when a hole drilling and digital speckle pattern interferometry (DSPI) combined system is used to measure residual stresses. The proposed method is based on a least-square calculation of three correction parameters determined from two evaluation lines located near the edge of the phase map where the displacement field generated by the drilling process is supposed to be negligible. The errors introduced by the method for different residual stress levels and rigid body displacements are analysed using a numerical simulation. An application of the method to experimental data is also presented.     

Volume-grating phase-shifting digital speckle pattern interferometry used for measurement of out-of-plane displacement field

A new digital speckle pattern interferometry, called volume-grating phase-shifting digital speckle pattern interferometry, is discussed in this paper. The out-of-plane displacement field of a bent plate can be quantitatively measured using volume-grating phase-shifting digital speckle pattern interferometry proposed in this paper. Theoretical and experimental results, as well as absolute errors, are given.     

Feasibility study of a digital speckle pattern interferometry and bending test combined technique to investigate coating adhesion

This paper presents a feasibility study to assess whether digital speckle pattern interferometry could be used as a possible technique to investigate the adhesive performance of coatings. The approach is based on the measurement of the deflections produced by a pre-notched coated specimen subjected to a four-point bending test. When the bending load is increased, a delamination between the coating and the substrate is propagated with its length depending on the adhesion strength. Experiments carried out with specimens having simulated delaminations confirm that digital speckle pattern interferometry can be used to estimate the delamination length.     

Wavelet filtering applied to time-average digital speckle pattern interferometry fringes

In this paper we are presenting a filtering scheme using Symlet wavelet to remove the speckle noise from the time-averaged digital speckle pattern interferometry fringes. To demonstrate the potential of Symlet wavelet filtering, experiments are conducted to remove the speckle noise from the fringes recorded for the surface of computer hard disk. Experimental results demonstrate that this filtering removes the speckle noise to the large extent.     

Quantitative vibration amplitude measurement with time-averaged digital speckle pattern interferometry

A new method of using time-averaged digital speckle pattern interferometry for the quantitative measurement of vibration amplitude was developed. Signal processing techniques especially the Hilbert transformation for quantitative evaluation of the Bessel fringes obtained in time-averaged digital speckle pattern interferometry were explored. The quadrature signal after Hilbert transformation is equivalent to a 90° phase-shifted interferogram for a monotonically increasing or decreasing phase function. An algorithm was developed for Bessel fringe contrast enhancement and phase extraction. The techniques were tested numerically and experimentally. Sub-fringe quantification of the time-averaged vibration fringes is realised with the proposed method. Compared with the commonly used phase shift method which requires a minimum of two images for image processing, this method requires only one fringe pattern for data extraction.     

Measurement of the near-tip displacement field in a fatigue damaged steel plate by digital speckle pattern interferometry

A digital speckle pattern interferometry system with automatic data analysis is used to measure the near-tip in-plane displacement field in a stainless steel specimen previously cracked by a fatigue test. In-plane displacements over a zone of 3.15 mm×3.15 mm are determined through the evaluation of the optical phase distribution. A theoretical solution developed for elasto-plastic materials is used to evaluate the obtained experimental results.     

Comparison between instantaneous and integral intensities in dynamic speckle pattern interferometry

A new speckle measurement technique called temporal speckle pattern interferometry or time sequential speckle pattern interferometry has been developed recently. Its principle is that by capturing the temporal speckle patterns related to the object deformation or displacement, the whole-field displacement, the amplitude of the vibrating object and the shape of the tested object can be calculated through speckle intensity fluctuation scanning technique or Fourier-transforming method. In this paper, we combine the analytical and numerical methods to simulate the properties of the time demodulation in temporal speckle patterns interferometry techniques. The performance of three kinds of temporal phase sequences, power, exponential and harmonic phase sequences, are studied with the parameters of temporal speckle intensity fluctuation, the value of the spatial phase term, optical integral time of the recording camera and the initial phase of the temporal speckle intensities. The results indicate that the normalized value and period change of the instantaneous intensity are nearly coincident with that of the integral intensity for the harmonic temporal phase sequences and are different for the power and exponential temporal phase sequences.     

Deformation field induced by spherical indentation: numerical analysis and experimental measurement by speckle interferometry

The present paper describes an experimental procedure for the measurement of the displacement field around a spherical indentation. The measurements were performed by a speckle interferometer designed for the detection on small areas of one or more oblique components of displacement; the indentations were made by a standard durometer used for metals.The experiments were carried out on a hardened and tempered steel, previously characterized by a standard tensile test; the results are in accordance with the numerical results obtained by an elasto-plastic FEM analysis.     

Evaluation of the piezoelectric behaviour produced by a thick-film transducer using digital speckle pattern interferometry

This paper presents an interferometric measurement of the out-of-plane deflections produced by a piezoelectric transducer, manufactured by thick-film deposition of a ceramic paste over an alumina substrate, when is subjected to a DC electric voltage. It is shown that a digital speckle pattern interferometer with an incorporated phase-shifting facility allows the measurement of nanometer displacements generated by the piezoelectric device. These measurements are used to evaluate the effective piezoelectric charge constant along the polarization direction (d₃₃)_eff that characterizes the thick-film transducer.     

Measurement of sub-surface delaminations in carbon fibre composites using high-speed phase-shifted speckle interferometry and temporal phase unwrapping

A high-speed phase-shifted speckle interferometer has been developed recently for studying dynamic events. Speckle interferograms are continuously recorded by a CCD camera operating at 1 kHz with temporal phase shifting carried out by a Pockels cell running at the same frequency. Temporal phase unwrapping through sequences of more than 1000 frames allows the determination of time-varying absolute displacement maps. This paper presents the application of this speckle interferometry system to the detection and measurement of sub-surface delamination defects in carbon fibre specimens. The influence of re-referencing the temporal phase unwrapping algorithm after different time intervals is analysed to reduce the random phase errors produced by speckle decorrelation and vibration. The performance of several phase-shifting algorithms to minimize the influence of the vibration noise caused by the vacuum pump used to load the specimen is also investigated.     

Evaluation of the 1D empirical mode decomposition method to smooth digital speckle pattern interferometry fringes

The 1D empirical mode decomposition method is applied to reduce speckle noise in the correlation fringes produced in digital speckle pattern interferometry. This method is based on the decomposition of a signal in a sum of well-behaved fast and slow oscillation modes through a sifting process, which generates a fully data-driven technique. Consequently, this is an adaptive approach and the use of basis functions in the analysis process is not required. The denoised signal is given by the residue obtained after the fast oscillation modes are removed. The performance and limitations of the denoising technique are analyzed using computer simulated fringes and these results are compared with those obtained using a wavelet sub-band removal approach. An application of the EMD method to denoise experimental correlation fringes is also presented.     

Continual deformation analysis with scanning phase method and time sequence phase method in temporal speckle pattern interferometry

If a laser beam illuminates a continual deformation object surface, it will lead to a temporal speckle pattern on the observation plane. Recording this time-dependent speckle pattern the deformation of the surface of an object can be obtained. Two methods, scanning phase method (SPM) and time sequence phase method (TSPM), have been introduced for measuring the displacement caused by the deformation in temporal speckle pattern interferometry (TSPI). Their principle is that by capturing a series of speckle interference patterns related to the object deformations, the fluctuations in the intensity of the interference patterns can be obtained. Through scanning these fluctuations and estimating both the average intensity and modulation of the temporal speckle interference patterns, the phase maps for whole-field displacements are calculated. In this way one is capable of quantitatively measuring continual displacements simply using a conventional electronic speckle pattern interferometry (ESPI) system without phase shifting or a carrier. The elaboration on the new methods is given in this paper and experiments are performed to demonstrate their performance with a conventional ESPI system.     

Determination of residual stresses using hole drilling and digital speckle pattern interferometry with automated data analysis

A digital speckle pattern interferometry and hole drilling combined system is developed to determine the magnitude of the residual stress in a aluminum thin plate subjected to an uniform uniaxial tensile load. Performing automated fringe analysis, the optical data contained in the speckle interferograms are quickly converted into values of residual stress. The evaluation is carried out through the measurement of the in-plane displacement field generated by the introduction of the small hole. The displacement field is determined from the calculation of the optical phase distribution by means of a phase shifting method. The magnitude of the residual stress is finally evaluated through a least-squares calculation and compared with the stress value applied to the specimen.     

Measuring thickness change of transparent plate by electronic speckle pattern interferometry and digital image correlation

The thickness change of transparent plates was measured by electronic speckle pattern interferometry (ESPI) method and digital image correlation (DIC) method. An out-of-plane ESPI system was developed based on the Michelson interferometer, and a new thickness measurement method was designed, which is on the basis of Snell's law of refraction and DIC. The main principles and experimental procedures of these two methods were presented. The thickness change of polymethyl specimens under uniaxial tensile loading were measured by the optical techniques and compared with each other. The results reveal that the data obtained with DIC method achieve better linearity than ESPI.     

The design of a non-cube beam-splitter used for electronic speckle pattern interferometry

A non-cube beam-splitter (NCBS) is proposed, by which an incident beam can be separated largely in a direction and then the lights from the test object and the lights from a reference surface placed adjacently to the test object can be combined to construct a simple electronic speckle pattern interferometry (ESPI) system. Two mainly useful quantitative ways, to calculate the phase change of the test object, the phase-shift and the fringe carrier method with Fourier transform, can be achieved in the ESPI system with the NCBS. Experiments with phase-shifting and fringe carrier method are completed. The experimental results show that the monolithic design of the proposed NCBS is effective in ESPI measurement and immunity to vibrations.     

Measurement of out-of-plane static and dynamic deformations by processing digital speckle pattern interferometry fringes using wavelet transform

In this paper, we are presenting measurement of static and dynamic deformations in rectangular plate fixed at one end using digital speckle pattern interferometry (DSPI). To improve the measurement accuracy, we have developed a new filtering scheme based on combination of average/median filtering and Symlet wavelet filtering which enhances the signal-to-noise ratio (SNR) in the speckle interferogram obtained from DSPI. Experimental results show that our filtering scheme is quite effective in improving SNR of the speckle interferogram. The measurements by DSPI and calculations from beam theory in the case of out-of-plane static deformation and the measurements by DSPI and accelerometer in the case of dynamic deformation are in good agreement.     

散斑干涉相位条纹图的频域滤波处理

为了解决在数字散斑干涉技术测量时,散斑干涉相位条纹图像中大量噪声对相位解包裹结果和精度产生严重影响的问题,介绍了一种条纹正余弦分解和频域低通滤波结合的方法,实现了散斑干涉相位条纹图的高精度滤波。该方法的基本思路是在对相位图像进行滤波处理前,先将相位图通过正余弦函数进行映射转换成两幅图,分别经过频域滤波,然后再合成为相位图。这种分解频域滤波方法可以在滤波的同时,有效保留相位跳变信息。实验结果表明：与传统的图像降噪方法相比,该方法能够在保留图像“尖峰”信息的基础上,较好地滤除图像中的散斑噪声,方法简单有效,有效解决了传统滤波方法应用在相位条纹图中,相图灰度信息丢失10%~40%的问题。