Unexpectedly high young's moduli recorded for iPP/HDPE blends

Young's moduli of a series of quenched isotactic polypropylene/high‐density polyethylene blends were measured. The moduli of many of the blends exceeded the upper bound, calculated from the parallel model with the moduli of the two quenched homopolymers as those of the two components. In fact, both components crystallized at higher temperatures in the blends than they did on their own. It is argued that the higher crystallization temperatures of the components lead to higher component moduli and that this can explain the observation that the measured moduli of the blends apparently exceeded the upper bound. The implications of this work are discussed in light of other studies concerning the measurement and calculation of blend moduli. © 2001 John Wiley & Sons, Inc. J Polym Sci B Part B: Polym Phys 39: 1404–1414, 2001     

iPP/HDPE/CB三元导电复合材料的导电与流变行为

利用界面能原理使CB选择性分布于HDPE中成为复合导电相,固定CB在HDPE中的质量分数(20 wt％),控制CB/HDPE导电相在iPP中的含量,制备出一系列三元(iPP/HDPE/CB)导电复合材料,并研究其导电逾渗和流变逾渗行为.结果表明,在复合导电相含量为20 wt％时复合材料内即形成导电网络,在复合导电相含量30 wt％时出现流变网络.只有当复合导电相在材料中形成连续相时(60 wt％),损耗因子在频率扫描中才出现峰值.     

iPP/HDPE/CB复合材料的制备及反常的温度-电阻效应

本文利用普通熔融挤出法制备了iPP/HDPE/CB复合材料, 分别采用注射成型及压制成型方法得到测试试样. 通过研究复合材料体积电阻率随温度的变化, 考察注塑试样和压制试样的PTC特性及复合材料形态结构与试样PTC特性之间的关系.     

聚丙烯／聚乙烯共混物高取向薄膜的形态结构研究

在等规聚丙烯(iPP)与高密度聚乙烯(HDPE)共混物的熔体拉伸薄膜中,两组份均以高取向的片晶形式存在,片晶生长方向垂直于拉伸方向。当iPP含量小于20％时,无明显的iPP相区存在;在iPP含量为40—60％时,两组份各自形成继续相,而在iPP含量大于70％时,HDPE以分散相存在。iPP的加入,使HDPE的片晶宽度减小,同时影响其结构的对称性,即由纯HDPE的非对称近单晶结构变为对称的纤维结构。 在制膜温度较高(135—140℃),HDPE含量较低(小于30％)时,HDPE在iPP上附生结晶。两种片晶的c轴成45°—50°交角,附生结晶的接触面为HDPE的(100)和iPP的(010)。     

Epitaxial behavior of HDPE on the boundary of highly oriented iPP substrates

The epitaxial crystallization behavior of high-density polyethylene on the boundary of highly oriented isotactic polypropylene (iPP) substrates has been investigated by means of atomic force microscopy (AFM) and transmission electron microscopy (TEM). The results obtained from AFM and TEM indicate that the epitaxial nucleation of HDPE on the highly oriented iPP substrates occurs earlier than that in the pure HDPE phase, i.e., homogeneous nucleation. Therefore the epitaxially grown HDPE lamellae can grow across the boundary of the iPP substrate into the HDPE spherulitic phase with the epitaxial orientation relationship remaining.     

热处理对HDPE／iPP共混物中附生结晶的影响

木工作用透射电子显微术研究不同热处理温度对HDPE/iPP共混物溶液浇铸薄膜中附生结晶的影响。经热处理的共混物薄膜HDPE片晶尺寸明显增加,但其长轴仍与iPP成约50°夹角。电子衍射和暗场的实验结果及样品倾斜技术的利用证明了在iPP的两种结构区域中HDPE均在iPP上异相附生生长,两者的接触面为iPP的(010)和HDPE的(100)。在194℃热处理20min,然后自然冷却的HDPE/iPP共混物薄膜中的HDPE仍然在iPP上附生生长。     

Effects of EPDM rubber on crystallization behaviour and morphology of iPP/HDPE blend

The effects of EPDM rubber on the crystallization behaviour of isotactic polypropylene (iPP) in the ternary iPP/HDPE/EPDM blends were studied by means of DSC and X-ray diffraction. Analysis of the crystallization exotherm peaks in terms of crystallization nucleation and growth rates and crystallinity revealed variations in the morphology of the iPP component in the blends as a function of the EPDM content. The DSC and X-ray diffraction results showed that the overall crystallinity decreased as the weight percentage of EPDM was increased in the iPP/HDPE blends.The morphology of these blends was studied by scanning electron microscopy, which revealed a random distribution of EPDM throughout the iPP matrix. The size and number of these rubber particles increased with increase of the EPDM weight percentage in the ternary iPP/HDPE/EPDM blends. The probable existence of composite inclusions of EPDM-HDPE in an iPP matrix is suggested.

---

Zusammenfassung Die Effekte von EPDM-Kautschuk auf das Kristallisationsverhalten von isotaktischem Polypropylen (iPP) in den ternären Gemischen iPP/HDPE/EPDM wurden mittels DSC und Röntgendiffraktometrie untersucht. Die Analyse der exothermen Kristallisationspeaks mit Hinblick auf die Kristallisationskeimbildung und die Geschwindigkeit des Kristallwachstums und die Kristallinität deuten auf morphologische Varianten der iPP-Komponente in den Gemischen in Abhängigkeit vom EPDM-Gehalt hin. Die durch DSC und Röntgendiffraktometrie erhaltenen Ergebnisse zeigen, daß die Kristallinität mit steigendem Gehalt an EPDM in den iPP/HDPE-Gemischen abnimmt. Die Morphologie dieser Gemische wurde durch Scanningelektronenmikroskopie untersucht. Es wurde eine random-Verteilung des EPDM in der iPP-Matrix festgestellt. Größe und Zahl dieser Kautschukpartikel nehmen mit zunehmendem EPDM-Gewichtsanteil in den ternären iPP/HDPE/EPDM-Gemischen zu. Auf die wahrscheinliche Existenz von EPDM/HDPE-Einschlüssen in einer iPP-Matrix wird hingewiesen.

---

(-) - -. , , , . , --. , . ---. - - .

     

Preparing iPP/HDPE/CB functionally gradient materials: influence factors of components and processing

In this work, gradient materials with low electrical resistivity were prepared by compounding isotactic polypropylene (iPP)/high density polyethylene (HDPE) blends with carbon black (CB) through extruding and injection molding. Contact angle measurements and morphology measurements showed that the CB particles were selectively located in HDPE phase and the final composites had a gradient structure that the HDPE/CB phase exhibited different morphologies in the skin layer and core layer of the composites under different processing procedures. The main factors influencing the formation of the functional gradient materials (FGM), including screw speed during extruding, iPP types and CB contents were discussed. They affect the phase morphology by shear stress, the restoration of HDPE phase, and the viscosity ratio of polymer blends, respectively. In conclusion, iPP/HDPE/CB FGM could be formed easily in the composites blending with the iPP type with narrow molecular weight distribution (MWD) and higher CB content extruded at higher screw speed. The electrical properties of iPP/HDPE/CB composites were studied and the results showed that screw speed in extrusion significantly influenced the percolation curve and electrical property of the final composites. Copyright © 2011 John Wiley & Sons, Ltd.     

Epitaxial and graphoepitaxial growth of isotactic polypropylene (iPP) from the melt on highly oriented high density polyethylene (HDPE) substrates

Although under normal conditions only the crystallization behavior of PE on oriented iPP substrates can be studied due to the higher melting point of iPP, the faster crystallization rate of a molten, oriented HDPE film compared to a nonoriented iPP layer was used to study the crystallization of iPP on the oriented HDPE film by means of transmission electron microscopy (TEM) and electron diffraction (ED). Besides the known epitaxial relationship of HDPE/iPP with their chains 50° apart, two new orientation relationships with (a) chains of both polymers parallel and (hk0)_iPP in contact with the HDPE substrate, and (b) the a‐axis of iPP crystals parallel to the chain direction of HDPE but (001)_iPP in contact with the HDPE substrate were observed. Both orientations are assumed as graphoepitaxy. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 1893–1898, 1999     

温度对iPP和TMB-5/iPP结晶行为的影响

通过DSC和同步辐射WAXS技术测定了结晶温度对iPP和TMB-5/iPP结晶行为的影响.结果表明,随等温结晶温度升高,iPP总结晶度变化不大,但是β晶型含量降低的同时α晶型含量增加.TMB-5是一种具有温度依赖的选择性成核剂,当等温结晶温度高于140℃时,含TMB-5成核剂的iPP的β晶型的含量急剧降低.本文进一步探讨了TMB-5对iPP结晶行为影响的机理.     

Crystallization and morphology of iPP/MWCNT prepared by compounding iPP melt with MWCNT aqueous suspension

In this work, isotactic polypropylene (iPP) composites filled with multiwalled carbon nanotubes (MWCNTs) were prepared by compounding iPP melt with MWCNT aqueous suspension using a corotating twin-screw extruder, and the morphology and crystallization behavior of the composites were investigated. Scanning electron microscopy micrographs showed that MWCNTs dispersed individually at nanoscale in the iPP matrix when the MWCNTs concentration was low, though MWCNTs aggregates were detected when the filler concentration increased. The results of differential scanning calorimetry, wide-angle X-ray diffraction, and polarized light microscopy indicated that the β-form crystal of iPP was induced by MWCNTs at the concentration of 0.1 wt.% which was dispersed individually in the iPP matrix. At higher content, however, MWCNTs acted as α-nucleating agent, and the crystals in the iPP/MWCNT composites showed higher degree of perfection than that of pure iPP though smaller in dimension. Crystallization rate of iPP increased significantly with increasing MWCNT content.     

Deformation and failure kinetics of iPP polymorphs

In this study, the mechanical performance of the different polymorphs of isotactic polypropylene, typically present in iPP crystallized under industrial processing conditions, is assessed. Different preparation strategies were used to obtain samples consisting of almost solely α, β, or γ crystals. X‐Ray measurements were used to validate that the desired phase was obtained. The intrinsic true stress ‐ true strain response of all individual phases was measured in uniaxial compression at several strain rates (deformation kinetics). Moreover, measurements were performed over a wide temperature range, covering the window in between the glass transition and the melting temperature. The relation between obtained yield stress and the strain rate is described with a modification of the Ree‐Eyring model. Differences and similarities in the deformation kinetics of the different phases are presented and discussed. Furthermore, the presence of three deformation processes, acting in parallel, is revealed. The Ree‐Eyring equation enables lifetime prediction for given thermal and mechanical conditions. These predictions were experimentally validated using constant load tests in uniaxial compression. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2017 , 55, 729–747     

聚丙烯结晶行为的PVT研究

通过受限液体PVT测量技术对等规聚丙烯的结晶行为进行了研究,采用PVT等压测量模式描述了不同压力场下半结晶聚合物的结晶过程.结果表明,随着压力的升高,等规聚丙烯分子链间的相互作用增强,使得等规聚丙烯分子链段更容易排入晶格中,这是结晶温度和结晶速度升高的主要因素.通过对数据拟合,建立了压力对等规聚丙烯结晶过程参数的影响公式.对Jeziorny结晶动力学模型进行改进,并研究了压力对等规聚丙烯结晶动力学的影响,结果发现,当结晶度大于0.08时,结晶动力学拟合曲线呈较好的线性,分析结果可以对结晶过程的变化机理进行合理地预测,在小于200 MPa压力环境下,等规聚丙烯的结晶生长方式仍是球晶生长模式,晶体的生长符合二维片晶生长方式,自由体积的减小是结晶速率加快的主要原因之一.     

聚丙烯成核剂研究进展

聚丙烯材料被越来越多的应用于汽车领域、工程塑料等,聚丙烯性能的优化也成为工业界和学术界研究的热点问题。聚丙烯因其良好的机械性能、加工性能、价格低廉而备受关注,但其低温脆性大、热变形温度低、易收缩等缺点也制约了该类材料的发展和在某些领域的应用。对聚丙烯的改性关键是对其分子链规整度、球晶尺寸的调控,成核剂改性是聚丙烯改性中相对简单易行的方法。聚丙烯成核剂种类繁多,各俱特色,本文在综述了聚丙烯成核剂的基础上提出了新型聚丙烯改性成核剂,即大分子成核剂,并展望了大分子成核剂的发展前景。     

Rheological properties of UHMWPE/iPP blends

The effects of isotactic polypropylene (PP) on the rheological properties of ultra high molecular weight polyethylene (UHMWPE) have been measured in a broad range of composition (0, 5, 15, 30 wt% PP) at various temperatures (110, 130, and 150°C) and a specific gel concentration of 6 wt%. The result showed that the viscosity of the UHMWPE significantly decreased with the addition and increasing amount of PP. Regardless of temperature, the viscosity function followed the power‐law behavior. Copyright © 2009 John Wiley & Sons, Ltd.     

等规聚丙烯自成核的等温结晶动力学

近年来 ,有关等规聚丙烯 (i PP)的自成核研究已引起了人们的关注 [1 ] ,但有关其结晶动力学的报道并不多见 .Carfagna等 [2 ]用膨胀计法研究了 i PP在未完全熔融重结晶情况下的等温结晶动力学 ,得到的 Avrami指数远远小于 3 .张新远等[3 ] 研究了 i PP未完全熔融情况下的非等温结晶动力学 .到目前为止 ,i PP自成核的熔体降温等温结晶动力学尚未见报道 .本文在 i PP自成核研究的基础上 [4] ,用 DSC方法研究了 i PP自成核在较高温度下的等温结晶动力学 ,讨论了结晶机理 .结果表明 ,在本实验的自成核条件下 ,i PP依然是三维球晶生长 ,…     

Di-azides cross-linked, iPP/EPDM-based thermoplastic vulcanizates

Two di-azidoformates: 4,4′-isopropylidenediphenyl azidoformate (4,4′DAF), and tri(ethylene glycol)-di(azidoformate) (GDAF), and one di-sulfonyl azide: 1,3-benzenedisulfonyl azide (1,3BDSA), are investigated as cross-linking agents for iPP/EPDM-based dynamically vulcanized thermoplastic vulcanizates (TPVs). Their performance is compared with TPVs cured with peroxide, alone and in combination with a coagent. The di-azides proved already to be effective curing agents for EPDM-rubber in static conditions in a previous study. With respect to the production conditions of the investigated TPVs, the reaction temperature of the sulfonyl azide makes it the most suitable cross-linking agent. Exceptionally good mechanical properties are obtained with very low 1,3BDSA loadings. The results indicate that, in the 1,3BDSA cross-linked TPVs the EPDM-rubber particles size significantly change with the curative concentration.