CeO2:Eu3+粉末的溶胶-凝胶法制备及发光性能研究

采用溶胶-凝胶法制备了不同浓度Eu3 掺杂的CeO2发光粉,样品粉末在紫外光激发下发出明亮的橙红色光.利用X射线衍射(XRD)、热重-差热分析(TG-DTA)和光致发光光谱(PL)对样品的结晶过程和发光性质进行了表征.XRD分析表明在0.2at.%～10at.%的Eu3 掺杂范围内,用溶胶-凝胶法合成的样品在500℃就结晶成纯相的CeO2:Eu3 多晶粉末.由于Ce4 和Eu3 离子半径十分接近,因而Eu3 在CeO2中具有较高的固溶度.PL激发谱中出现在300～390 nm的宽带激发峰起源于基质CeO2的吸收,电子吸收能量后,发生O2--Ce4 的电荷迁移,再将能量传递给Eu3 .PL发射谱显示Eu3 含量为6at.%的样品发光强度最强,随后出现浓度猝灭.导致发光出现浓度猝灭的机制是电偶极-电四极相互作用.样品烧结温度的升高,促使晶粒长大和结晶完整性提高,从而显著提高了CeO2:Eu3 粉末的发光强度.     

Synthesis and properties of La1-xSrxNiO3 and La1-xSrxNiO2

Superconductivity has been realized in films of La_1-xSr_xNiO₂. Here we report synthesis and characterization of polycrystalline samples of La_1-xSr_xNiO₃ and La_1-xSr_xNiO₂ (0 ≤ x ≤ 0.2). Magnetization and resistivity measurements reveal that La_1-xSr_xNiO₃ are paramagnetic metal and La_1-xSr_xNiO₂ exhibit an insulating behavior. Superconductivity is not detected in bulk samples of La_1-xSr_xNiO₂. The absence of superconductivity in bulk La_1-xSr_xNiO₂ may be due to the generation of hydroxide during reduction, a small amount of nickel impurity, or incomplete reduction of apical oxygen. The effect of interface in films of La_1-xSr_xNiO₂ may also play a role for superconductivity.     

Si基Bi3.25La0.75Ti3O12铁电薄膜的制备与特性研究

采用Sol-Gel工艺低温制备了Si基Bi3.25La0.75Ti3O12铁电薄膜.研究了退火温度对薄膜微观结构、介电特性与铁电性能的影响.500℃退火处理的Bi3.25La0.75Ti3O12薄膜未能充分晶化,晶粒细小且有非晶团聚,介电与铁电性能均较差.高于550℃退火处理的Bi3.25La0.75Ti3O12薄膜表面平整无裂纹,晶粒均匀,无焦碌石相或其他杂相,薄膜为多晶生长,具有较好的介电与铁电性能,4V电压下的漏电流密度低于2×10-8A/cm2.随退火温度升高,晶化程度的提升和晶粒尺寸的增大使薄膜的剩余极化增大而矫顽电场降低.600℃退火处理的Bi3.25La0.75Ti3O12薄膜显示了优于Bi4Ti3O12薄膜的铁电性能,其剩余极化Pr和矫顽电场Ec分别达到17.5μC/cm2和102kV/cm.     

含吡啶环的双醛腙类试剂的合成及其光谱研究

有机电致发光技术在彩色大屏幕平板显示技术方面己经显示出了广阔的应用前景,是当今国际平板显示技术领域研究的热点之一。开发性能优良的电子传输材料是提高有机及聚合物 LED 性能的关键。双席夫碱类金属配合物同时满足了电荷平衡和配位数饱和两个条件,可以得到非常纯的荧光,能够成为良好的电致发光材料。文章设计并合成了四种新的含吡啶环的双醛腙类化合物,通过红外光谱、元素分析、荧光光谱对合成的化合物进行了表征,确定了化合物结构。对所合成化合物红外光谱进行了分析,确定了该类化合物的红外特征吸收峰;荧光光谱表明该类化合物具有良好的荧光性,其最大发射波长在420～440 nm之间,其荧光强度的大小与衍生物中不同的取代基有关,—OH、呋喃环、胡椒醛等起供电子作用的基团,使荧光波长发生红移。     

2,3,4-三羟基苯乙酮腙类试剂的合成及其光谱研究

用连苯三酚合成2,3,4-三羟基苯乙酮,用苯甲酸乙酯、对羟基苯甲酸甲酯与水合肼反应,合成苯甲酰肼和对羟基苯甲酰肼,然后用2,3,4-三羟基苯乙酮与苯甲酰肼、对羟基苯甲酰肼、苯肼反应,合成了三种新的2,3,4-三羟基苯乙酮腙类试剂。研究了腙类试剂的红外光谱、紫外光谱、荧光光谱特性。     

Electrical Properties and Raman Spectra of BaBi1-xPbxO3

Crystal structure, electrical properties and Raman spectra of BaBi1-xPbxO3 are reported. The result of x-ray diffraction shows that the specimen is pure, and the lattice parameters decrease continuously in the semiconducting range, whereas it vibrates similarly to a sine wave in the superconducting range, which is ascribed to the existence of oxygen vacancies and the function of breathing modes of Bi（Pb）O6. The temperature dependence of resistivity indicates that the electrical property of the samples is connected sensitively with the crystal structures. Raman spectra show that the specimen becomes disorder when x increases, and the critical temperature To depends not only on the deformation potential of the soft A19 mode derived from the Bi（Pb）O6 rigid rotation, but also on the energy shift of the mode.     

SrTiO_3(100)上La_(1-x)Sr_xMnO_3超薄膜的特性(英文)

In this paper, we briefly report the property difference of La_(1-x)Sr_xMnO_3 (x=0.1) ultra-thin films (~([001]) orientation) at different thickness grown on SrTiO_3 (100) substrate.It is found that the magnetic interaction is greatly enhanced when film t…     

应变对La_(1-x)Sr_xMnO_3薄膜的物理性质的影响(英文)

Both tensile strain and compressive strain effects on the properties of La_(1-x)Sr_xMnO_3 (x=0.1) films were investigated.The films on SrTiO_3 (100) display 'unusual' tensile strain~([1]), which supports a ferromagnetic metallic behavior when film thickness is larger than 10nm.The films on NdGaO_3 (100) presenting compressive strain, on the other hand, demonstrate strongly enhanced insulating behavior.Inordertoobtainunambiguousresults,allfilmsampleswerepreparedusingthesamedepositionconditi…     

Synthesis of Novel Spiro-Oxazino-Quinoline Derivatives and Study of Their Photophysical Properties

A convenient route was successfully developed for the synthesis of novel heterocycles such as spiro-oxazino-quinoline derivatives from 2-aminoquinoline-3-carbonitrile (4) in good yield. The Spiro-quinoline derivatives (6, 8 and 10) were synthesized and further studied for their photophysical properties. Semiempirical molecular orbital calculation (PM3/PM6 for structure) proves to be a suitable tool for the prediction of absorption and fluorescence properties of these compounds.     

溶胶-凝胶法Er_2O_3薄膜的结构和光学特性

针对稀土Er掺杂Si光源中Er离子掺杂浓度低的问题,采用溶胶-凝胶(Sol-gel)法在Si(100)和SiO2/Si(100)基片上旋涂法制备Er2O3光学薄膜,Er离子浓度与以前掺杂方法相比提高了2个数量级.900℃热处理获得单一立方结构的Er2O3薄膜材料.光致发光(PL)特性研究表明在654nm波长的激光泵浦下,Er2O3薄膜材料获得了1.535μm的发光峰,并具有较小的温度猝灭1/5.在SiO2/Si(100)基体上制备的Er2O3薄膜材料的光致发光强度比Si(100)基体上制备的薄膜提高2-3倍.研究结果表明具有强光致发光特性的Er2O3薄膜是一种有前景的硅基光源和放大器材料.     

Electrical and electrochemical characterization of microstructured thin film La1−xSrxCoO3 electrodes

Thin film microstructured La_1−xSr_xCoO₃ (LSCO) electrodes for micro-SOFC application and kinetic studies were characterized by 4 probe electrical conductivity and electrochemical impedance spectroscopy (EIS). The electrical conductivity was analyzed between RT and 700 °C and was found to be strongly dependent on the thin film deposition parameters, in particular on the oxygen partial pressure during deposition. The highest conductivity measured at 600 °C was 700 S/cm. EIS was carried out on different substrate materials. SiO₂ was found to be the most promising substrate material with respect to chemical and electrical inertness. Four main contributions were observed by EIS and were attributed respectively to the series resistance of the LSCO, to the grain boundary impedance of the CGO electrolyte and to LSCO electrode reactions.     

Ca3La(BO3)3：Tb3+的合成与发光性质

高温固相反应法合成了Ca₃La(BO₃)₃:Tb³⁺光致发光材料。利用扫描电镜和激光衍射分析仪测定了样品的晶粒形貌及粒径大小分布,利用荧光分光光度计研究了Ca₃La(BO₃)₃:Tb³⁺的光致发光特性。确定了在Ca₃La(BO₃)₃基质中Tb³⁺离子浓度对其发光强度的影响及其自身浓度猝灭机理;探讨了助熔剂Li₂CO₃、敏化剂Ce³⁺离子的加入对荧光粉发光强度的影响。     

Magnetic Properties of Fe2O3 Particles Prepared by Sol-Gel Method

Fe₂O₃ fine particles dispersed in a silica gel have been prepared by a new sol-gel method and characterized. Various samples have been studied by means of Mössbauer spectroscopy for temperatures ranging between 4.2 K and 300 K. The results show that the average particle size and the kinds of Fe₂O₃ phase obtained (α, γ or ε) are strongly dependent of the temperature on the final heat treatment.     

溶胶凝胶法制备Ti1-xFexO2纳米颗粒及磁性能研究

采用溶胶凝胶法制备了稀磁半导体Ti1-xFexO2(x=0～0.050)的纳米颗粒,在氩气氛围中以500℃对样品进行退火处理,并通过差热/热重综合热分析仪(TG-DTA)、X射线衍射仪(XRD)、拉曼光谱(Raman)分析了纳米颗粒的结构和相变温度.使用振动样品磁场计(VSM)测试了样品的磁性能.研究发现:经500℃氩...     

新型溶胶-凝胶二氧化硅微孔增透膜的制备及性能研究

以正硅酸乙酯为前驱体,二甲基二乙氧基硅烷为造孔剂,采用溶胶凝胶技术在酸催化条件下制备了二氧化硅溶胶;采用提拉法在K9玻璃基片上双面镀膜,经500 ℃热处理,制备得到一种新型单层微孔二氧化硅增透膜。通过改变造孔剂加入量,膜层峰值透过率可达到99.7％,而硬度仍保持在2H以上,同时具有良好的耐摩擦性及粘附性。加速腐蚀实验表明,膜层的环境稳定性是常规膜层的10倍以上。由于该新型增透膜兼具高透过率、良好的机械性能以及很强的环境稳定性,因而在改善太阳能玻璃增透性能方面有极大的应用价值。     

1,8-二巯基芘分子电学特性的理论研究

在第一性原理的基础上 ,对 1,8 二巯基芘分子的电学特性进行了理论研究 .采用了 3个Au原子构成的团簇来模拟Au表面 .首先利用密度泛函理论计算了 1,8 二巯基芘分子的电子结构及其和Au表面的相互作用 ,再利用前线轨道理论和微扰理论定量地确定了该分子和Au表面的相互作用能常数 .最后利用弹性散射格林函数法研究了该分子结的伏 安特性 .计算结果表明 ,分子中的硫原子和Au原子形成很强的共价键 .当外加偏压小于 1V时分子结存在电流禁区 ,随着偏压升高 ,分子结的电导出现平台结构 .分子结的电导特性和其电子结构密切相关 ,扩展分子轨道为电荷的迁移提供了通道 ,而局域轨道对电流贡献很小     

(La,Ce,Tb)BO3的合成及光谱性质

采用高温固相法合成了(La,Ce,Tb)BO₃绿色发光粉,并对该发光粉进行了XRD和SEM分析。结果表明:(La,Ce,Tb)BO₃的晶体结构和LaBO₃相同,Ce³⁺、Tb³⁺的掺入并没有改变晶体的结构,发光粉颗粒大小均匀,形貌规则,粒度在5 μm左右。研究了(La,Ce,Tb)BO₃的光谱性质,在(La,Ce,Tb)BO₃的发射和激发光谱中除了有Tb³⁺的特征发射和激发峰外,还有Ce³⁺的特征发射和激发峰。比较了(La,Ce)BO₃发射光谱和(La,Tb)BO₃的激发光谱,两者存在重叠,这为Ce³⁺→Tb³⁺的能量传递提供了条件。将(La,Ce,Tb)BO₃的发射光谱与商品粉(La,Ce,Tb)PO₄进行比较,两者的发射主峰都在541 nm处, (La,Ce,Tb)BO₃在489 nm处的峰位稍有红移,通过计算表明,(La,Ce,Tb)BO₃的发光亮度达到商品粉(La,Ce,Tb)PO₄的94.7%。因此,(La,Ce,Tb)BO₃是一种很有应用前景的绿色发光粉。     

高压制备Ag_(1-x)Pb_(18)SbTe_(20)及其电学性能的研究

采用高压方法制备了Ag偏离化学计量比的Ag1-xPb18SbTe20(x=0,0.3,0.6)样品,研究了Ag含量及温度对样品电学输运性能的影响。X射线衍射测试结果表明,样品具有单相NaCl结构,晶格常数随Ag含量的减少而变小。电学输运性能测试表明:与常规制备方法相比,高压方法制备的AgPb18SbTe20样品的电导率较高;样品电导率随x的增大而逐渐增大,x=0.6时,室温条件下的样品电导率高达1 598.4S/cm。随着温度的升高,Seebeck系数增大,电导率减小。300℃时,Ag0.4Pb18SbTe20样品的功率因子达到最大值,约为1.97mW/(m·K2)。