Epitaxial growth of YSZ buffer layer for YBa2Cu3O7−δ coated conductor by reel-to-reel pulsed laser deposition

Yttria-stabilized zirconia (YSZ) buffer layers were deposited on CeO₂ buffered biaxially textured Ni-W substrate by reel-to-reel pulsed laser deposition (PLD) for the application of YBa₂Cu₃O_7−δ (YBCO) coated conductor and the influence of substrate temperature and laser energy on their crystallinity and microstructure were studied. YSZ thin films were prepared with substrate temperature ranging from 600 to 800 °C and laser energy ranging from 120 to 350 mJ. X-ray diffraction (XRD), scanning electron microscopy (SEM), and atomic force microscopy (AFM) were used to investigate how thin film structure and surface morphology depend on these parameters. It was found that the YSZ films grown at substrate temperature below 600 °C or laser energy above 300 mJ showed amorphous phase, the (0 0 1) preferred orientation and the crystallinity of the YSZ films were improved with increasing the temperature, but the surface roughness increased simultaneously, the SEM images of YSZ films on CeO₂/NiW tapes showed surface morphologies without micro-cracks. Based on these results, we developed the epitaxial PLD-YSZ buffer layer process at the tape transfer speed of 3-4 m/h by the reel-to-reel system for 100 m class long YBCO tapes.     

Growth and structure of Bi0.5(Na0.7K0.2Li0.1)0.5TiO3 thin films prepared by pulsed laser deposition technique

Bi_0.5(Na_0.7K_0.2Li_0.1)_0.5TiO₃ (BNKLT) thin films were prepared on Pt/Ti/SiO₂/Si substrates by pulsed laser deposition (PLD) technique. The films prepared were examined by using X-ray diffraction (XRD), scanning electron microscopy (SEM) and atomic force microscopy (AFM). The effects of the processing parameters, such as oxygen pressure, substrate temperature and laser power, on the crystal structure, surface morphology, roughness and deposition rates of the thin films were investigated. It was found that the substrate temperature of 600 °C and oxygen pressure of 30 Pa are the optimized technical parameters for the growth of textured film, and all the thin films prepared have granular structure, homogeneous grain size and smooth surfaces.     

Synthesis,structure, and electrochemical properties of epitaxial perovskite La0.8Sr0.2CoO3 film on YSZ substrate

Epitaxial films of the perovskite, La_0.8Sr_0.2CoO₃ (LSC), for SOFCs cathode were deposited on yttria-stabilized zirconia (YSZ) single crystals by pulsed laser deposition method. The films were characterized by thin-film X-ray diffraction measurement, atomic force microscopy (AFM), transmission electron microscope (TEM), and ac impedance spectroscopy. The film orientations depend on the substrate planes. The LSC films on the YSZ (100) and (111) substrates showed the (110) orientation with different twin structures, while those on the YSZ (110) had (100) and (112) orientations. Surface morphology of the films also depends on the substrate orientations. These films showed different electrode properties depending on the orientations. The relationships between the properties, the film orientations, surface morphology, and lattice misfit are discussed.     

Effect of substrate morphology on the roughness evolution of ultra thin DLC films

The effect of substrate roughness on growth of ultra thin diamond-like carbon (DLC) films has been studied. The ultra thin DLC films have been deposited on silicon substrates with initial surface roughness of 0.15, 0.46 and 1.08 nm using a filted cathodic vacuum arc (FCVA) system. The films were characterized by Raman spectroscope, transmission electron microscope (TEM) and atomic force microscopy (AFM) to investigate the evolution of the surface roughness as a function of the film thickness. The experimental results show that the evolution of the surface morphology in an atomic scale depends on the initial surface morphology of the silicon substrate. For smooth silicon substrate (initial surface roughness of 0.15 nm), the surface roughness decreased with DLC thickness. However, for silicon substrate with initial surface roughness of 0.46 and 1.08 nm, the film surface roughness decreased first and then increased to a maximum and subsequently decreased again. The preferred growth of the valley and the island growth of DLC were employed to interpret the influence of substrate morphology on the evolution of DLC film roughness.     

Non-monotonous dependence of surface roughness on factors influencing energy of adatoms during thin island film growth

Many experimental results show that surface roughness of thin films can increase, decrease, stay constant or pass through the minimum with the change in substrate temperature, energy of arriving atoms or assisted beam (electrons, photons, ions), depending on material and interval of variation of those parameters. The aim of this paper is to explain and analyze this non-monotonous behavior of surface roughness by proposed kinetic model. The model is based on rate equations and includes processes of surface diffusion of adatoms, nucleation, growth and coalescence of islands in the case of thin films growth in Volmer-Weber mode. It is shown by modeling that non-monotonous dependence of surface roughness on the factors influencing energy of adatoms (e.g. temperature, assisted beam irradiation, accelerating voltage) occurs as a result of interplay between diffusion length of adatoms and size of islands, because both parameters depend on energy of adatoms. Variation of island size and diffusion length results in atomic jumps from islands forming rougher or smoother surface. The functions of surface roughness, island size, island density on diffusion length of adatoms and on other parameters are calculated and analyzed in this work.     

Pulsed laser deposition of semiconducting crystalline double-doped barium titanate thin films on nickel substrates

We synthesized by pulsed laser deposition (Ba,Sr,Y)TiO₃ and (Ba,Pb,Y)TiO₃ thin films on mechanically polished nickel substrates.The synthesized thin films were analyzed for: crystalline structure by X-ray diffractometry, morphology and surface topography by atomic force microscopy, optical and scanning electron microscopy, and elemental composition by energy dispersive X-ray spectroscopy and electrical properties by electrical measurements.We have shown that film properties were determined by the dopants, target composition, and deposition parameters (oxygen pressure, substrate temperature and incident laser fluence). All films exhibited a semiconducting behavior, as proved by the decrease of electrical resistance with heating temperature.     

Effect of La2Zr2O7-buffered YSZ substrate on YBa2Cu3Oy thin films by chemical solution deposition

Epitaxial YBa₂Cu₃O_y (YBCO) thin films have been fabricated by chemical solution deposition (CSD) on La₂Zr₂O₇-buffered YSZ single crystal substrate, where the buffer layer has three kinds of morphology – flat surface, rough surface and pore surface. The effect of LZO buffer layer’s roughness on the YBCO films was evaluated by X-ray diffraction, scanning electron microscopy and temperature-dependent resistivity measurements. The flat surface of LZO layer is beneficial to highly epitaxial YBCO films and high critical current density.     

Electron beam evaporated LaF3 thin films prepared by different temperatures and deposition rates

LaF₃ thin films were prepared by electron beam evaporation with different temperatures and deposition rates. Microstructure properties including crystalline structure and surface roughness were investigated by X-ray diffraction (XRD) and optical profilograph. X-ray photoelectron spectroscopy (XPS) was employed to study the chemical composition of the films. Optical properties (transmittance and refractive index) and laser induce damage threshold (LIDT) at 355 nm of the films were also characterized. The effects of deposition rate and substrate temperature on microstructure, optical properties and LIDT of LaF₃ thin films were discussed, respectively.     

衬底温度对PLD制备的Mo薄膜结构及表面形貌的影响

 运用脉冲激光沉积(PLD)技术在Si(100)基片上沉积了金属Mo薄膜。在激光重复频率2 Hz,能量密度5.2 J/cm²,本底真空10^－6 Pa的条件下,研究Mo薄膜的结构和表面形貌,讨论了衬底温度对薄膜形貌与结构的影响。原子力显微镜(AFM)图像和X射线小角衍射(XRD)分析表明,薄膜表面平整、光滑,均方根粗糙度小于2 nm。沉积温度对Mo薄膜结构和表面形貌影响较大,在373~573 K范围内随着温度升高,薄膜粗糙度变小,结晶程度变好。     

Al2O3 thin films by plasma-enhanced chemical vapour deposition using trimethyl-amine alane (TMAA) as the Al precursor

2 O₃ thin films by plasma-enhanced chemical vapour deposition (PECVD) using trimethyl-amine alane (TMAA) as the Al precursor. The thin films were deposited on both Si and quartz silica (SiO₂) substrates. Deposition rates were typically 60 Å min^-1 keeping the TMAA temperature constant at 45 °C. The deposited Al₂O₃ thin films were stoichiometric alumina with low carbon contamination (0.7–1.3 At%). The refractive index ranged from 1.54 to 1.62 depending on the deposition conditions. The deposition rate was studied as a function of both the RF power and the substrate temperature. The structure and the surface of the deposited Al₂O₃ thin films were studied using X-ray diffraction, atomic force microscopy (AFM) and scanning electron microscopy (SEM). Received: 20 May 1997/Accepted: 12 June 1997     

聚酰亚胺薄膜表面粗糙度的影响因素

 采用热蒸发气相沉积聚合方法（VDP）制备了聚酰亚胺(PI)薄膜,研究了设备、衬底温度、升温过程和单体配比因素对PI薄膜表面形貌的影响。利用干涉显微镜和扫描电镜对薄膜表面形貌进行了分析;利用原子力显微镜测定了薄膜表面粗糙度。结果表明：设定蒸发源-衬底距离为74 cm时可成连续膜;蒸发源采用一段升温和多段升温时,膜表面均方根粗糙度分别为291.23 nm和61.99 nm;采用细筛网可防止原料的喷溅;均苯四甲酸二酐和4,4′-二氨基二苯醚（PMDA和ODA）单体沉积速率比值为0.9∶1时,膜表面均方根粗糙度值可减小至3.30 nm;沉积衬底温度保持30 ℃左右时,膜表面均方根粗糙度为4.01 nm, 随温度的上升,膜表面质量会逐渐变差。     

The effect of nitrogen pressure on the two-step method deposition of GaN films

GaN thin films were deposited on sapphire (0001) substrates at different nitrogen pressures by pulsed laser deposition (PLD) of GaN target in nitrogen atmosphere. Good single crystal GaN thin films were obtained after annealing at 1000 °C for 15 min in a NH₃ atmosphere. An Nd:YAG pulsed laser with a wavelength of 1064 nm was used as the laser source. The influence of nitrogen pressure on the thickness, crystallinity and surface morphology of GaN films were characterized by X-ray diffraction (XRD), atomic force microscopy (AFM) and Raman spectroscopy. The results show that at low nitrogen pressure, the surface diffusion of adatoms can be influenced by the collisions between the nitrogen gas molecules and the activated atoms, which can influence the kinetic energy of the activated atoms. However, at high nitrogen pressure, the kinetic energy of adatoms is decided by the annealing temperature. In our experimental conditions, the GaN thin films deposited at 0.75 and 7.5 Pa have a high surface morphology and crystalline quality. PACS 71.55.Eq; 74.62.Fj     

Epitaxial growth and structural characterization of Pb(Fe1/2Nb1/2)O3 thin films

We have grown lead iron niobate thin films with composition Pb(Fe_1/2Nb_1/2)O₃ (PFN) on (0 0 1) SrTiO₃ substrates by pulsed laser deposition. The influence of the deposition conditions on the phase purity was studied. Due to similar thermodynamic stability spaces, a pyrochlore phase often coexists with the PFN perovskite phase. By optimizing the kinetic parameters, we succeeded in identifying a deposition window which resulted in epitaxial perovskite-phase PFN thin films with no identifiable trace of impurity phases appearing in the X-ray diffractograms. PFN films having thicknesses between 20 and 200 nm were smooth and epitaxially oriented with the substrate and as demonstrated by RHEED streaks which were aligned with the substrate axes. X-ray diffraction showed that the films were completely c-axis oriented and of excellent crystalline quality with low mosaicity (X-ray rocking curve FWHM?0.09°). The surface roughness of thin films was also investigated by atomic force microscopy. The root-mean-square roughness varies between 0.9 nm for 50-nm-thick films to 16 nm for 100-nm-thick films. We also observe a correlation between grain size, surface roughness and film thickness.     

Fe/Al混合膜的PLD法制备及表面分析

 采用脉冲激光气相沉积（PLD）技术制备了Fe/Al混合膜,测量了该混合膜的光电子能谱（XPS）,并采用原子力显微镜（AFM）、扫描电子显微镜（SEM）对Fe/Al混合膜作了表面分析。结果表明：Fe/Al混合膜的表面粗糙度对衬底温度有明显的依赖性, 随着衬底温度的升高,薄膜的表面逐渐变得平滑,膜层变得致密,在200 ℃衬底温度下制得了均方根（rms）粗糙度为0.154 nm、具有原子尺度光滑性的Fe/Al混合膜, 膜中Fe和Al分布比较均匀,其成分比约为1∶3,同时XPS分析也表明Fe/Al混合膜暴露在空气中后表面形成了Al₂O₃和FeO氧化层。     

Structural and tribological properties of cluster-assembled CNx films

We report the structural and tribological characterization of nanostructured CN_x thin films produced by the deposition of a supersonic carbon cluster beam assisted by nitrogen ion bombardment. The influence of the deposition parameters on the chemical composition and structure of the films has been systematically studied by X-ray photoelectron spectroscopy, elastic recoil detection analysis, transmission electron microscopy and atomic force microscopy. Depending on the deposition parameters, the films show a structure ranging from amorphous to disordered graphitic with interlinked planes. Nitrogen content depends on the nitrogen ion kinetic energy. The films have a very low density with a high surface roughness. Friction measurements at the nanoscale show a correlation between nitrogen content and mechanical properties of the system. PACS 61.46-w     

Structural and optical properties of YSZ thin films grown by PLD technique

We report on the structural and optical properties of yttria stabilized zirconia (YSZ) thin films grown by pulsed laser deposition (PLD) technique and in situ crystallized at different substrate temperatures (T_s = 400 °C, 500 °C and 600 °C). Yttria-stabilized zirconia target of ∼1 in. diameter (∼95% density) was fabricated by solid state reaction method for thin film deposition by PLD. The YSZ thin films were grown on an optically polished quartz substrates and the deposition time was 30 min for all the films. XRD analysis shows cubic crystalline phase of YSZ films with preferred orientation along 〈1 1 1〉. The surface roughness was determined by AFM for the films deposited at different substrate temperatures. The nano-sized surface roughness is found to increase with the increase of deposition temperatures. For the optical analysis, a UV-vis-NIR spectrophotometer was used and the optical band gap of ∼5.7 eV was calculated from transmittance curves.     

Direct current magnetron sputter-deposited ZnO thin films

Zinc oxide (ZnO) is a very promising electronic material for emerging transparent large-area electronic applications including thin-film sensors, transistors and solar cells. We fabricated ZnO thin films by employing direct current (DC) magnetron sputtering deposition technique. ZnO films with different thicknesses ranging from 150 nm to 750 nm were deposited on glass substrates. The deposition pressure and the substrate temperature were varied from 12 mTorr to 25 mTorr, and from room temperature to 450 °C, respectively. The influence of the film thickness, deposition pressure and the substrate temperature on structural and optical properties of the ZnO films was investigated using atomic force microscopy (AFM) and ultraviolet-visible (UV-Vis) spectrometer. The experimental results reveal that the film thickness, deposition pressure and the substrate temperature play significant role in the structural formation and the optical properties of the deposited ZnO thin films.     

Preparation of smooth Fe (001) on MgO (001)

The high mobility of metal adsorbates on perfect oxide surfaces favours an island-growth mode, which results in a granular morphology for metallic thin films. At low temperature, a fast substrate coverage is achieved due to the reduced mobility which, on the other hand, inhibits the development of an atomically smooth surface. In this study we used a controlled procedure to grow smooth epitaxial films of a few nanometres of Fe on MgO (001). The development of the dynamic conductivity as a measure of morphological roughness was observed during metal deposition by means of in-situ infrared spectroscopy. At various steps of thin-film preparation we used low-energy electron diffraction (LEED) for a characterisation of the crystalline surface quality. With ex situ atomic force microscopy (AFM) we investigated the surface topology of the prepared films with respect to smoothness. For example, for a controlled-growth 2-nm film, we observed a sharp LEED pattern and a metallic dynamic conductivity, and we did not find the distinct grooves which are characteristic of a granular structure. Received: 23 June 2000 / Accepted: 19 December 2000 / Published online: 21 March 2001     

Surface partition of ion energy during the growth of TiNx thin films

A simple evaluation of ion-deposited energy during surface displacement of adatoms has been presented for physical vapor deposition technology using an appropriate interaction model. The rf reactive magnetron sputtering deposition of titanium nitride (TiN_x) thin films was taken as evidence supporting the theoretical calculation. The evolution of crystallite morphology dependent on bias (or input power) illustrates that surface and subsurface microstructure of growing films can be optimized by increasing the mobility of adatoms through ion-assistance.