Growth of transparent conducting nano-structured In doped ZnO thin films by pulsed DC magnetron sputtering

Transparent conducting nano-structured In doped zinc oxide (IZO) thin films are deposited on corning 7059 glass substrates by bipolar pulsed DC magnetron sputtering with variation of pulsed frequency and substrate temperature. Highly c-axis oriented IZO thin films were grown in perpendicular to the substrate on the 30 kHz and 500 °C. The IZO films exhibited surface roughness of 3.6 nm similar to the commercial ITO and n-type semiconducting properties with electrical resistivity (carrier mobility) of about 5 × 10⁻³ Ω cm (14 cm²/V s). The optical characterization showed high transmittance of over 85% in the UV-vis region and exhibited the absorption edge of near 350 nm. In micro-Raman spectra, the origin of two additional modes is attributed to the host lattice defect due to the addition of In dopant. These results suggest that the IZO film can possibly be applied to make transparent conducting electrodes for flat panel displays.     

Electrodeposition and characterization of thin selenium films modified with lead ad-atoms

The deposition and characterization of Se films doped with Pb underpotentially deposited (UPD) ad-atoms was studied in this work. The employed experimental techniques were cyclic voltammetry, chronoamperometry, electrochemical impedance spectroscopy, UV-vis spectroscopy and atomic force microscopy. The initial deposition of Se film by chronoamperometry yielded a thin film composed of approximately 700 layers. The Pb UPD on Se was achieved by chronoamperometry in a potential value previously determined in voltammetric experiments. This deposition yielded a deposition charge of approximately 7.5% of the total one. The film resistance altered from 320 Ω cm⁻² for Se to 65 Ω cm⁻² for the Se/Pb one. Flat band potential values and number of acceptors and donors were also calculated for both films and the values obtained were +0.95 and −0.51 V for Se and Se/Pb, respectively. The Se coating presented 1.2 × 10¹⁷ cm⁻³ acceptors while the Se/Pb one presented 3.2 × 10¹⁷ cm⁻³ donors. The band gap values for both films were 2.4 eV and 1.9 eV, correspondingly.     

Optical and electrical characteristics of Al-doped ZnO thin films prepared by aqueous phase deposition

Transparent conducting Al-doped ZnO (AZO) thin films have been deposited by sol-gel route. Starting from an aqueous solution of zinc acetate by adding aluminum chloride as dopant, a c-axis oriented polycrystalline ZnO thin film 100 nm in thickness could be spin-coated on glass substrates via a two-step annealing process under reducing atmosphere. The effects of thermal annealing and dopant concentration on the structural, electrical and optical properties of AZO thin films were investigated. The post-treated AZO films exhibited a homogenous dense microstructure with grain sizes less than 10 nm as characterized by SEM photographs. The annealing atmosphere has prominent impact on the crystallinity of the films which will in turn influence the electrical conductivity. By varying the doping concentrations, the optical and electrical properties could be further adjusted. An optimal doping concentration of Al/Zn = 2.25 at.% was obtained with minimum resistivity of 9.90 × 10⁻³ Ω-cm whereas the carrier concentration and mobility was 1.25 × 10²⁰ cm⁻³ and 5.04 cm² V⁻¹ s⁻¹, respectively. In this case, the optical transmittance in the visible region is over 90%.     

Electrical properties of La2O3 thin films grown on TiN/Si substrates via atomic layer deposition

The electrical as well as the structural properties of La₂O₃ thin films on TiN substrates were investigated. Amorphous stoichiometric La₂O₃ thin films were grown at 300 °C via atomic layer deposition technique by using lanthanum 2,2,6,6-tetramethyl-3,5-heptanedione [La(TMHD)₃] and H₂O as precursors. Post-annealing of the grown film induced dramatic changes in structural and the electrical properties. Crystalline phases of the La₂O₃ film emerged with the increase of the post-annealing temperature. Metal-insulator-metal (MIM) capacitor was fabricated to measure the electrical properties of the grown film. The dielectric constant of the La₂O₃ thin films increased with annealing temperature to reach the value of 17.3 at 500 °C. The leakage current density of the film post-annealed at 400 °C was estimated to be 2.78 × 10⁻¹⁰ and 2.1 × 10⁻⁸ A/cm² at ±1 V, respectively.     

Ag-N doped ZnO film and its p-n junction fabricated by ion beam assisted deposition

Ag-N doped ZnO film was synthesized by ion beam assisted deposition and its electrical properties and annealing property were investigated. The films remained p-type even after annealing at 400 °C in air for 10 min. While the annealing temperature went up to 500 °C, the conduction type of these films shifted from p-type to n-type. The p-type ZnO film revealed low resistivity (0.0016 Ω cm), low Hall mobility (0.65 cm² V⁻¹ s⁻¹) and high carrier concentration (5.8 × 10²⁰ cm⁻³). ZnO p-n homojunction consisting of a p-type layer (Ag-N doped ZnO film) and an n-type layer (In-doped ZnO film) had been fabricated by ion beam assisted deposition. With electrical measurement, its current-voltage curve had a typical rectifying characteristic with current rectification ratio of 25 at bias ±5 V and a reverse current of 0.01 mA at −5 V. The depletion width was estimated 3.8 nm by using p-n junction equation.     

Ferromagnetism in amorphous Ge1−xMnx grown by low temperature vapor deposition

Magnetic properties of amorphous Ge_1−xMn_x thin films were investigated. The thin films were grown at 373 K on (100) Si wafers by using a thermal evaporator. Growth rate was ∼35 nm/min and average film thickness was around 500 nm. The electrical resistivities of Ge_1−xMn_x thin films are 5.0×10⁻⁴∼100 Ω cm at room temperature and decrease with increasing Mn concentration. Low temperature magnetization characteristics and magnetic hysteresis loops measured at various temperatures show that the amorphous Ge_1−xMn_x thin films are ferromagnetic but the ferromagnetic magnetizations are changing gradually into paramagnetic as increasing temperature. Curie temperature and saturation magnetization vary with Mn concentration. Curie temperature of the deposited films is 80-160 K, and saturation magnetization is 35-100 emu/cc at 5 K. Hall effect measurement at room temperature shows the amorphous Ge_1−xMn_x thin films have p-type carrier and hole densities are in the range from 7×10¹⁷ to 2×10²² cm⁻³.     

Effect of Al incorporation on the structural,morphological, optoelectronic and transport properties of PbS thin films

Doping of PbS thin films with different metal atoms produce considerable changes in structural and material properties that make them useful in the technology of thin film devices. The goal of this work is to study the effects of doping on the structural, morphological, optoelectronic and transport properties of PbS thin films as a function of Al³⁺ concentration. Thin films of pure and Al doped PbS nanoparticles are prepared on soda lime glass substrates by chemical bath deposition technique. The Al content in aqueous solution is varied from 0 to 20 mg. XRD analysis of the films revealed significant enhancement in crystallinity and crystallite size up to an optimum concentration of doping. Films are polycrystalline with crystallite size 19–32 nm, having face centered cubic structure. The optical band gap energy exhibits a decreasing trend and is shifted from 2.41 to 1.34 eV with increasing Al content. The room temperature conductivity of the as-deposited PbS films is in the range of 0.78×10⁻⁸ to 0.67×10⁻⁶(Ω cm)⁻¹ with a maximum for optimum Al content. The Al doped PbS thin film, which we synthesize with optimum Al concentration of 15 mg is found to be a most suitable material for solar control coating applications.     

Influence of oxygen partial pressure on the properties of pulsed laser deposited nanocrystalline zirconia thin films

ZrO₂ thin films were deposited at various oxygen partial pressures (2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar) at 973 K on (1 0 0) silicon and quartz substrates by pulsed laser deposition. The influence of oxygen partial pressure on structure, surface morphology and optical properties of the films were investigated. X-ray diffraction results indicated that the films are polycrystalline containing both monoclinic and tetragonal phases. The films prepared in the oxygen partial pressures range 2.0 × 10⁻⁵-3.5 × 10⁻¹ mbar contain nanocrystals of sizes in the range 54-31 nm for tetragonal phase. The peak intensity of the tetragonal phase decreases with the increase of oxygen partial pressures. Surface morphology of the films examined by AFM shows the formation of nanostructures. The RMS surface roughness of the film prepared at 2.0 × 10⁻⁵ mbar is 1.3 nm while it is 3.2 nm at 3.5 × 10⁻¹ mbar. The optical properties of the films were investigated using UV-visible spectroscopy technique in the wavelength range of 200-800 nm. The refractive index is found to decrease from 2.26 to 1.87 as the oxygen partial pressure increases from 2.0 × 10⁻⁵ to 3.5 × 10⁻¹ mbar. The optical studies show two different absorption edges corresponding to monoclinic and tetragonal phases.     

High-conductive nanocrystalline silicon with phosphorous and boron doping

Intrinsic, P- and B-doped hydrogenated amorphous silicon thin films were prepared by plasma-enhanced chemical vapor deposition technique. As-deposited samples were thermally annealed at the temperature of 800 °C to obtain the doped nanocrystalline silicon (nc-Si) films. The microstructures, optical and electronic properties have been evaluated for the undoped and doped nanocrystalline films. X-ray photoelectron spectroscopy (XPS) measurements demonstrated the presence of the substitutional boron and phosphorous in the doped films. It was found that thermal annealing can efficiently activate the dopants in films accompanying with formation of nc-Si grains. Based on the temperature-dependent conductivity measurements, it was shown that the activation of dopant by annealing increased the room temperature dark conductivity from 3.4 × 10⁻⁴ S cm⁻¹ to 5.3 S cm⁻¹ for the P-doped films and from 1.28 × 10⁻³ S cm⁻¹ to 130 S cm⁻¹ for the B-doped films. Meanwhile, the corresponding value of conductivity activation energies was decreased from 0.29 eV to 0.03 eV for the P-doped films and from 0.3 eV to 5.6 × 10⁻⁵ eV for the B-doped films, which indicated the doped nc-Si films with high conductivity can be achieved with the present approach.     

Fabrication of p-type Li-doped ZnO films by pulsed laser deposition

p-Type ZnO thin films have been realized via doping Li as acceptor by using pulsed laser deposition. In our experiment, Li₂CO₃ was used as Li precursor, and the growth temperature was varied from 400 to 600 °C in pure O₂ ambient. The Li-doped ZnO film prepared at 450 °C possessed the lowest resistivity of 34 Ω cm with a Hall mobility of 0.134 cm² V⁻¹ s⁻¹ and hole concentration of 1.37 × 10¹⁸ cm⁻³. X-ray diffraction (XRD) measurements showed that the Li-doped ZnO films grown at different substrate temperatures were of completely (0 0 2)-preferred orientation.     

Effect of substrate temperature on properties of multilayer thin film based on ZnO and Mo-doped indium oxide

Zinc oxide/molybdenum-doped indium oxide/zinc oxide (ZnO/IMO/ZnO) multilayer thin films are grown using pulsed laser deposition technique. The effect of substrate temperature on structural, optical, and electrical properties of multilayer films is studied. It is observed that films grown at high substrate temperature are oriented along (0 0 2) and (2 2 2) direction for ZnO and IMO respectively. The crystallinity of these films increases with increase in substrate temperature. It is also seen that conductivity, carrier concentration, and mobility increase with increase in temperature. The multilayer film grown at 500 °C has low resistivity (7.67 × 10⁻⁵ Ω cm), high carrier concentration (3.90 × 10²⁰ cm⁻³), and high mobility (209 cm²/Vs).     

Fabrication and characterization of magnetron sputtered arsenic doped p-type ZnO epitaxial thin films

Arsenic doped p-type ZnO thin films were grown on sapphire substrate by magnetron sputtering. As grown films reveal p-type conduction confirmed by Hall-effect and photoluminescence measurements. The p-type film with a hole concentration of 2.16× 10¹⁷ cm⁻³, mobility of 1.30 cm²/V.s and resistivity of 22.29 Ω-m were obtained at substrate temperature of 700 °C. ZnO homojunction synthesized by in-situ deposition of As doped p-ZnO layer on Al doped n-ZnO layer showed p-n diode like characteristics. X-ray pole figure and Transmission Electron Microscope studies confirm epitaxial nature of the films. Photoluminescence results exhibit the peaks associated with donor acceptor pair emission.     

CuInS2 thin films obtained through the annealing of chemically deposited In2S3-CuS thin films

In this work, we report the formation of CuInS₂ thin films on glass substrates by heating chemically deposited multilayers of copper sulfide (CuS) and indium sulfide (In₂S₃) at 300 and 350 °C in nitrogen atmosphere at 10 Torr. CIS thin films were prepared by varying the CuS layer thickness in the multilayers with indium sulfide. The XRD analysis showed that the crystallographic structure of the CuInS₂ (JCPDS 27-0159) is present on the deposited films. From the optical analysis it was estimated the band gap value for the CIS film (1.49 eV). The electrical conductivity varies from 3 × 10⁻⁸ to 3 Ω⁻¹ cm⁻¹ depending on the thickness of the CuS film. CIS films showed p-type conductivity.     

Morphological and optical properties of silicon thin films by PLD

Silicon thin films have been prepared on sapphire substrates by pulsed laser deposition (PLD) technique. The films were deposited in vacuum from a silicon target at a base pressure of 10⁻⁶ mbar in the temperature range from 400 to 800 °C. A Q-switched Nd:YAG laser (1064 nm, 5 ns duration, 10 Hz) at a constant energy density of 2 J × cm⁻² has been used. The influence of the substrate temperature on the structural, morphological and optical properties of the Si thin films was investigated.Spectral ellipsometry and atomic force microscopy (AFM) were used to study the thickness and the surface roughness of the deposited films. Surface roughness values measured by AFM and ellipsometry show the same tendency of increasing roughness with increased deposition temperature.     

Combinatorial synthesis of Li-doped NiO thin films and their transparent conducting properties

Transparent and conductive oxide (TCO) thin films of Li-doped NiO were prepared by combinatorial pulsed laser deposition technique. Composition spread approach was applied to optimize the Li concentration for achieving high conductivity and transparency in the film. Conductivity of the composition spread film was found to increase almost linearly from nearly insulating to as high as 1.41 Ω⁻¹ cm⁻¹ with increasing Li content along a 9 mm long film. Optical transparency was found to decrease in an equal proportion across the 40 nm thick film with a slight shift in the absorption edge.     

Growth and characteristics of hydrogenated In-doped ZnO thin films by pulsed DC magnetron sputtering

We investigated the role of hydrogen impurities in highly oriented In-doped ZnO (IZO:H) films. The conductivity of ZnO:H films exhibit small variation despite the increase of hydrogen ratio. The small variation of the carrier concentration in IZO:H films can be explained by the reduction of the oxygen deficiency for the charge neutrality and the increase of Vzn-H bonding for partially charge compensation in the films. The additional mode at 573 cm⁻¹ is interpreted as vacancy clusters. The discrepancy between the increase of vacancy clusters (573 cm⁻¹) and small variation of carrier concentration is attributed to the different physical characteristics of the IZO:H films due to the hydrogen existence between bulk and surface. The measured FT-IR peak at 3500 cm⁻¹ exhibits typical characteristic of O-H bonding.     

Structural, optical and electrical characterization of highly conducting Mo-doped In2O3 thin films

Highly conducting and transparent thin films of molybdenum-doped indium oxide were deposited on quartz by pulsed laser deposition. The effect of growth temperature and oxygen partial pressure on the structural, optical and electrical properties was studied. We find that the film transparency depends on the growth temperature. The average transmittance of the films grown at different temperatures is in range of 48-87%. The X-ray diffraction results show that the films grown at low temperature are amorphous while the films grown at higher temperature are crystalline. Electrical properties are found to be sensitive to both the growth temperature and oxygen pressure. Resistivity of the films decreases from 1.3 × 10⁻³ Ω cm to 8.9 × 10⁻⁵ Ω cm while mobility increases from 9 cm²/V s to 138 cm²/V s as the growth temperature increases from room temperature to 700 °C. However, with increase in oxygen pressure, resistivity increases but the mobility decreases after attaining a maximum. The temperature-dependent resistivity measurements show transition form semiconductor to metallic behavior. The film grown at 500 °C under an oxygen pressure of 1.0 × 10⁻³ mbar is found to exhibit high mobility (250 cm²/V s), low resistivity (6.7 × 10⁻⁵ Ω cm), and relatively high transmittance (∼90%).     

Investigation on upconversion photoluminescence of Bi3TiNbO9:Er:Yb thin films

Bi₃TiNbO₉:Er³⁺:Yb³⁺ (BTNEY) thin films were fabricated on fused silica by pulsed laser deposition. It was demonstrated that different laser fluence and substrate temperature during growth of BTNEY upconversion photoluminescence (UC-PL) samples control the film’s grain size and hence influences the UC-PL properties. The average grain size of BTNEY thin films deposited on fused silica substrates with laser fluence 4, 5, 6, and 7 J/cm² are 30.8, 35.9, 40.6, and 43.4 nm, respectively. The 525 nm emission intensities increase with the deposition laser fluence and the emission intensities of BTNEY thin film deposited under 700 and 600 °C are almost 24 and 4 times, respectively, as strong as those of samples under 500 °C. The grain size of BTNEY thin film increases with the increasing temperature. UC-PL of BTNEY films is enhanced by increasing grain size of the films.     

Enhanced hardness in B-doped ZnO thin films on fused quartz substrates by pulsed-laser deposition

B-doped ZnO thin films have been fabricated on fused quartz substrates using boron-ZnO mosaic target by pulsed-laser deposition technique, and the mechanical properties have been studied by nanoindentation continuous stiffness measurement technique and transmission electron microscope (TEM). Nanoindentation measurement revealed that the hardness of B-doped ZnO films, 9.32 ± 0.90 to 12.10 ± 1.00 GPa, is much greater than that of undoped ZnO films and very close to that of traditional semiconductor Si. The mean transmittance (%) is larger than 81% in the visible range (380-780 nm) for all the films, and the Hall effect measurement showed that the carrier density is around 2 × 10²⁰ cm⁻³ and the resistivity lower than 3 × 10⁻³ Ω cm. TEM characteristics show undoped thin films have more amorphous area between grains while the B-doped ZnO films have thin grain boundaries. We suggest that the grain boundaries act as the strain compensation sites and the decrease in thickness of grain boundaries enhances the hardness of the B-doped ZnO films.     

Annealing temperature influence on electrical properties of ion beam sputtered Bi2Te3 thin films

Ion beam sputtering process was used to deposit n-type fine-grained Bi₂Te₃ thin films on BK7 glass substrates at room temperature. In order to enhance the thermoelectric properties, thin films are annealed at the temperatures ranging from 100 to 400 °C. X-ray diffraction (XRD) shows that the films have preferred orientations in the c-axis direction. It is confirmed that grain growth and crystallization along the c-axis are enhanced as the annealing temperature increased. However, broad impurity peaks related to some oxygen traces increase when the annealing temperature reached 400 °C. Thermoelectric properties of Bi₂Te₃ thin films were investigated at room temperature. The Bi₂Te₃ thin films, including as-deposited, exhibit the Seebeck coefficients of −90 to −168 μV K⁻¹ and the electrical conductivities of 3.92×10²-7.20×10² S cm⁻¹ after annealing. The Bi₂Te₃ film with a maximum power factor of 1.10×10⁻³ Wm⁻¹ K⁻² is achieved when annealed at 300 °C. As a result, both structural and transport properties have been found to be strongly affected by annealing treatment. It was considered that the annealing conditions reduce the number of potential scattering sites at grain boundaries and defects, thus improving the thermoelectric properties.