Raman scattering investigations on lanthanum-doped Bi4Ti3O12-SrBi4Ti4O15 intergrowth ferroelectrics

The ferroelectric ceramics of Bi₄Ti₃O₁₂, SrBi₄Ti₄O₁₅, and lanthanum-doped Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅ were synthesized, and their Raman spectra were investigated. La-doping resulted in the enlargement of remnant polarization of Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅. The structure of the Bi₂O₂ layers and TiO₆ octahedra of the intergrowth was found to be different from those of Bi₄Ti₃O₁₂ and SrBi₄Ti₄O₁₅. La³⁺ ions exhibit pronounced selectivity for the occupation of A site as La content is lower than 0.50, and tend to be incorporated into Bi₂O₂ layers when the La content is higher than 0.50. Lanthanum substitution brings about the structural phase transition in Bi₄Ti₃O₁₂-SrBi₄Ti₄O₁₅. The variation of ferroelectric property may be attributed to combined contribution from the decreasing of the oxygen vacancies, the relaxation of the lattice distortion, the destroying of the insulation and the space charge compensation effects of the Bi₂O₂ slabs.     

Bi3TaO7/MXene纳米片异质结的制备及光催化降解磺胺嘧啶钠

分别以五水合硝酸铋（Bi （NO₃）₃·5H₂O）和五氯化钽（TaCl₅）作为Bi源和Ta源,采用静电吸附和溶剂热法在2D Ti₃C₂的表面原位生长0D Bi₃TaO₇纳米颗粒制备Bi₃TaO₇/Ti₃C₂复合光催化材料。通过各种物理化学表征研究了2D Ti₃C₂纳米片对Bi₃TaO₇/Ti₃C₂复合光催化材料微结构的影响。通过可见光下降解磺胺嘧啶钠（SD-Na）溶液来评价所制备样品的光催化性能。实验结果表明,Bi₃TaO₇/Ti₃C₂复合材料的光催化性能明显增强。在最优条件下（Ti₃C₂与Bi₃TaO₇的质量比为0.02）制备的BT2展现出最高的光催化活性,其降解SD-Na溶液的表观速率常数是纯Bi₃TaO₇的2.8倍。Bi₃TaO₇/Ti₃C₂复合光催化材料性能的显著提高归因于Ti₃C₂/Bi₃TaO₇异质结的形成有利于光生载流子的快速转移和分离。     

Ti3C2Tx/MnO2正极在水系锌电池中的电化学性能

二氧化锰(MnO₂)材料具有比容量大、电极电位高、储量丰富以及价格低廉等优势,成为水系锌电池正极最受关注的一类材料,然而其仍然存在着结构稳定性差和电化学储存机理复杂的问题。因此,我们通过两步合成法制备了一种花苞状结构的MnO₂负载在Ti₃C₂T_x表面形成Ti₃C₂T_x/MnO₂复合材料,通过X射线粉末衍射(XRD)、X射线光电子能谱(XPS)、透射电子显微镜(TEM)和高分辨透射电子显微镜(HRTEM)对复合样品的结构、成分和形貌进行表征。通过将Ti₃C₂T_x/MnO₂复合材料作为正极,与锌负极匹配组装成水系锌电池,研究了其分别在2 mol·L^-1 ZnSO₄、2 mol·L^-1 ZnSO₄+0.1 mol·L^-1 MnSO₄、30 mol·L^-1三氟甲基磺酸四乙基铵(TEAOTf)+1 mol·L^-1三氟甲烷磺酸锌(ZnOTf)和3 mol·L^-1 ZnOTf四种电解液中的电化学性能。结果表明,Ti₃C₂T_x/MnO₂在2 mol·L^-1 ZnSO₄中的比容量较高,但循环稳定性很差。将TEAOTf盐和ZnOTf盐共溶于水中,设计了一种新型的含惰性阳离子的超高浓度盐包水电解液(30 mol·L^-1 TEAOTf+1 mol·L^-1 ZnOTf),不仅提高了Ti₃C₂T_x/MnO₂材料的可逆性,而且有效抑制了电极材料在循环过程中的溶解。     

Li4Ti5O12/(Cu+C)复合材料的制备及电化学性能

以Li₄Ti₅O₁₂,Cu(CH₃COO)₂·H₂O和C₆H₁₂O₆为前驱体,化学沉积与热分解结合合成锂离子电池负极材料Li₄Ti₅O₁₂/(Cu+C)。采用X-射线衍射(XRD)、扫描电子显微镜(SEM)、恒流充放电、循环伏安和电化学阻抗方法表征样品的结构、形貌和电化学性能。结果表明,Li₄Ti₅O₁₂表面包覆的Cu与C提高了Li₄Ti₅O₁₂电极材料的导电率,其循环性能和倍率性能得到有效地改善。在0.5C、1C和3C倍率下,经过50次充放电循环,放电比容量分别为168.2、160、140.6 mAh·g^-1,其容量保持率分别为88.7%、84.4%、71.2%。电化学阻抗测试表明,表面包覆的Cu与C使其电荷转移阻抗大幅度减少。     

Non-centrosymmetric Ba3Ti3O6(BO3)2

The compound previously reported as Ba₂Ti₂B₂O₉ has been reformulated as Ba₃Ti₃B₂O₁₂, or Ba₃Ti₃O₆(BO₃)₂, a new barium titanium oxoborate. Small single crystals have been recovered from a melt with a composition of BaTiO₃:BaTiB₂O₆ (molar ratio) cooled between 1100°C and 850°C. The crystal structure has been determined by X-ray diffraction: hexagonal system, non-centrosymmetric space group, a=8.7377(11) Å, c=3.9147(8) Å, Z=1, wR(F²)=0.039 for 504 unique reflections. Ba₃Ti₃O₆(BO₃)₂ is isostructural with K₃Ta₃O₆(BO₃)₂. Preliminary measurements of nonlinear optical properties on microcrystalline samples show that the second harmonic generation efficiency of Ba₃Ti₃O₆(BO₃)₂ is equal to 95% of that of LiNbO₃.     

LiMn2O4表面包覆Li4Ti5O12的制备及倍率特性

采用固相法合成了尖晶石型LiMn₂O₄，并通过溶胶-凝胶法制备了不同物质的量的百分比含量Li₄Ti₅O₁₂包覆的正极材料。X-射线衍射和扫描电镜结果表明，Li₄Ti₅O₁₂微粒包覆在LiMn₂O₄的表面没有产生晶体结构的变化。实验电池在室温下，以1C，2C和5C倍率作充放电循环测试；结果表明，与未包覆的LiMn₂O₄相比，表面包覆Li₄Ti₅O₁₂微粒的正极材料在高倍率下具有更好的循环稳定性。     

二维层状Ti3C2Tx-MXene@VS2用于高性能锂离子电池负极

为探索一种高性能的锂离子电池负极材料,采用酸刻蚀法制备了高导电性、高稳定性的二维层状Ti₃C₂T_x,通过溶剂热法制备了具有高理论比容量的花瓣状VS₂纳米片,再经过简单的液相混合得到了二维层状Ti₃C₂T_x-MXene@VS₂复合物。通过扫描电子显微镜、透射电子显微镜、X射线光电子能谱、X射线衍射和能谱分析对复合材料的形貌和结构进行了表征,采用循环伏安、恒流充放电、长循环和交流阻抗谱对复合材料的电化学性能进行了研究。结果表明：VS₂纳米片均匀地分布在Ti₃C₂T_x的层间及表面,该复合物具有高的可逆容量(电流密度为0.1A·g^-1时,比容量为610.5mAh·g^-1)、良好的倍率性能(电流密度为2A·g^-1时,比容量为197.1mAh·g^-1)和良好的循环稳定性(电流密度为0.2 A·g^-1时,循环600圈后比容量为874.9 mAh·g^-1;电流密度为2 A·g^-1时,循环1 500圈后比容量为115.9mAh·g^-1)。     

Synthesis, structure and electrical properties of Cu3.21Ti1.16Nb2.63O12 and the CuOx-TiO2-Nb2O5 pseudoternary phase diagram

Subsolidus phase relations in the CuO_x-TiO₂-Nb₂O₅ system were determined at 935 °C. The phase diagram contains one new phase, Cu_3.21Ti_1.16Nb_2.63O₁₂ (CTNO) and one rutile-structured solid solution series, Ti_1−3xCu_xNb_2xO₂: 0<x<0.2335 (35). The crystal structure of CTNO is similar to that of CaCu₃Ti₄O₁₂ (CCTO) with square planar Cu²⁺ but with A site vacancies and a disordered mixture of Cu⁺, Ti⁴⁺ and Nb⁵⁺ on the octahedral sites. It is a modest semiconductor with relative permittivity ∼63 and displays non-Arrhenius conductivity behavior that is essentially temperature-independent at the lowest temperatures.     

球形Bi_4Ti_3O_(12)制备及其可见光催化性能

采用水热法合成球形钛酸铋复合氧化物光催化剂,利用SEM、XRD和UV-Vis DRS等表征手段对复合氧化物的晶体结构、微观形貌和光学性能进行了分析,结果表明,制备的钛酸铋复合氧化物为10 nm的球形颗粒,具有良好的晶型结构,禁带宽度为2.7 nm,有较好的可见光吸收能力。以亚甲基蓝、甲基橙及酸性品红为目标污染物,研究了复合氧化物在可见光下的光催化降解有机污染物的性能,并对光催化降解机理进行了探讨。结果表明,在可见光照射下,该复合氧化物对酸性品红降解效果明显优于亚甲基蓝和甲基橙,光照150 min下,降解率可达91%。     

球形Bi4Ti3O12制备及其可见光催化性能

采用水热法合成球形钛酸铋复合氧化物光催化剂,利用SEM、XRD和UV-Vis DRS等表征手段对复合氧化物的晶体结构、微观形貌和光学性能进行了分析,结果表明,制备的钛酸铋复合氧化物为10 nm的球形颗粒,具有良好的晶型结构,禁带宽度为2.7 nm,有较好的可见光吸收能力。以亚甲基蓝、甲基橙及酸性品红为目标污染物,研究了复合氧化物在可见光下的光催化降解有机污染物的性能,并对光催化降解机理进行了探讨。结果表明,在可见光照射下,该复合氧化物对酸性品红降解效果明显优于亚甲基蓝和甲基橙,光照150 min下,降解率可达91%。     

Li4Ti5O12/(Ag+C)电极材料的固相合成及电化学性能

以Li₂CO₃,TiO₂为原料,葡萄糖为碳源,采用固相煅烧工艺合成了亚微米级的Li₄Ti₅O₁₂/C复合负极材料。并将之与AgNO₃复合,采用固相方法制备出了Ag表面修饰的Li₄Ti₅O₁₂/(Ag+C)复合材料。采用XRD、SEM和TEM测试方法对材料的微结构进行了表征。结果表明,C的存在对Ag单质在Li₄Ti₅O₁₂/C颗粒表面的大量形成起到了积极的促进作用,从而很大程度地提高了Li₄Ti₅O₁₂/C的电导率,因此有效地改善了其电化学性能。在1C倍率下,Li₄Ti₅O₁₂/(Ag+C)复合材料的首次放电容量达到了164 mAh·g^-1。     

La2Ti6O15-CeTi21O38-PbTiO3 ceramics formed in gaseous penetration of La-Ce into PbTiO3 and their electric properties

The gaseous penetration of La-Ce into PbTiO₃ ceramics is reported. The compounds of La₂Ti₆O₁₅ and CeTi₂₁O₃₈ are formed and the new La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃ ceramics are prepared by the penetration of La and Ce in the gaseous state. The new ceramic materials have a significant change in electric properties. The room temperature resistivity decreases from 2.0×10¹⁰ to 0.248 Ω. m, and the grain resistance exhibits an obvious PTCR effect with the change of temperature. However, the grain boundary resistance decreases rapidly with increase in temperature. The change rule of the total resistance is similar to that of the grain boundary, and the PTCR effect disappears and the tendency of transition to a conductive body is manifest. The XPS analysis suggests that the particles that are Pb, Ti, La and Ce in La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃ ceramics all change their valence and lead to decreasing resistivity, and the bound energy peak values of elements in La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃ ceramics are also reported. The La₂Ti₆O₁₅-CeTi₂₁O₃₈-PbTiO₃ ceramics have a better thermal stability in high temperatures through TG-DTA analysis.     

Ni0.8Co0.15Al0.05C2O4@Graphene的合成及电化学性能研究

过渡金属氧化物/石墨烯复合材料具有优异的电化学性能被广泛应用在锂离子电池中。本文以硫酸镍、硫酸钴、硫酸铝、草酸为原料按一定的物质的量比配制成溶液,在120°C的条件下水热反应12小时,得到多元过渡金属氧化物前驱体Ni_0.8Co_0.15Al_0.05C₂O₄(NCA-C₂O₄);该前驱体经聚烯丙基胺盐酸盐修饰后,与氧化石墨烯进行复合并还原得到石墨烯包覆的多元过渡金属氧化物/石墨烯负极材料Ni_0.8Co_0.15Al_0.05C₂O₄@Graphene(NCA-C₂O₄@G)。对材料的结构、形貌和电化学性质进行了表征。扫描电镜测试结果显示样品粒度均一,具有两端不规则长方体形貌。电化学性能测试结果表明：石墨烯包覆后的NCA-C₂O₄@G充放电容量高于前驱体NCA-C₂O₄,NCA-C₂O₄@G复合材料在0.1C电流密度 (1C=1000 mAh/g)下首次放电比容量为1956 mA h/g;经过0.1C、0.2C、0.5C、1C、2C高倍率循环后,当测试电流密度恢复至100 mA/g时,复合材料比容量可迅速回升至720 mA h/g,并在随后50次循环中比容量保持稳定,显示出良好的循环稳定性和倍率性能。     

Bi2Ti2O7/TiO2复合纤维：原位水热合成及光催化性能

采用静电纺丝技术制备的TiO2纤维作为模板和反应物,通过原位水热合成了具有异质结构的Bi2Ti2O7/TiO2复合纤维。利用X射线衍射(XRD)、扫描电镜(SEM)、能量散射光谱(EDS)、高分辨透射电镜(HRTEM)和紫外可见吸收光谱(UV-Vis)等分析测试手段对样品的结构和形貌进行表征。以罗丹明B为模拟有机污染物进行光催化降解实验。结果表明:花状Bi2Ti2O7纳米结构均匀地生长在TiO2纤维上,制备了Bi2Ti2O7与TiO2相复合的光催化材料,其光谱响应范围拓宽至可见光区,与纯TiO2纤维相比可见光催化活性显著提高,且易于分离、回收和循环使用。初步探讨了Bi2Ti2O7/TiO2异质结的生长机制和光催化活性提高机理。     

Synthesis, structure and magnetic properties of new phosphates K2Mn0.5Ti1.5(PO4)3 and K2Co0.5Ti1.5(PO4)3 with the langbeinite structure

New complex phosphates of the general formula K₂M_0.5Ti_1.5(PO₄)₃ (M=Mn, Co) have been obtained from the melting mixture of KPO₃, K₄P₂O₇, TiO₂ and CoCO₃·mCo(OH)₂ or Mn(H₂PO₄)₂ by means of a flux technique. The synthesized phosphates have been characterized by the single-crystal X-ray diffraction and the FTIR-spectroscopy. The compounds crystallize in the cubic system with the space group P2₁3 and cell parameters a=9.9030(14) Å for K₂Mn_0.5Ti_1.5(PO₄)₃ and a=9.8445(12) Å for K₂Co_0.5Ti_1.5(PO₄)₃. Both phosphates are isostructural with the langbeinite mineral and contain four formula unit K₂M_0.5Ti_1.5(PO₄)₃ per unit cell. The structure can be described using [M₂(PO₄)₃] framework composed of two [MO₆] octahedra interlinked via three [PO₄] tetrahedra. The Curie-Weiss-type behavior is observed in the magnetic susceptibility.     

Phase relations in NaxCrxTi8−xO16 at 1350 °C and crystal structure of hollandite-like Na2Cr2Ti6O16

Phase relations of rutile, freudenbergite, and hollandite structures were examined in the pseudobinary system NaCrO₂-TiO₂ (i.e., Na_xCr_xTi_8−xO₁₆) at 1350 °C. The hollandite structure was obtained in the composition range 1.7?x?2.0. The symmetry of the samples at room temperature was tetragonal for x=1.7 and 1.75, and monoclinic for x=1.8 and above. Single crystals of monoclinic hollandite Na₂Cr₂Ti₆O₁₆ were grown and the structure refinement has been carried out using an X-ray diffraction technique. The space group was I2/m and cell parameters were a=10.2385(11), b=2.9559(9), c=9.9097(11)Å, and β=90.545(9)° with Z=1. The Na ion distribution in the tunnel was markedly deformed from that in the tetragonal form. It was suggested that Cr/Ti ratios were different between the two framework metal sites.     

Vibrational spectra of cyclooctatetraenyl alkali metal complexes [C8H8M2 (M = Na, K)]: A theoretical study

The cyclooctatetraenyl dianion (C₈H₈²⁻) π-conjugated system forms a stable complex system with alkali and some transition metals. The results of vibrational analysis for C₈H₈M₂ (M = Na, K) complexes were reported here. The geometries of C₈H₈M₂ (M = Na, K) were optimized using ab initio (HF, MP2, CCSD(T)) and DFT (B3LYP) methods with 6-311G** and 6-311++G** basis sets and the harmonic frequencies were obtained. To reproduce and compare with the experimental values the structurally similar molecules C₅H₅M (M = Na, K) and benzene were studied. The scale factors obtained from these systems were applied to predict the experimental frequencies of C₈H₈M₂ (M = Na, K). The force field and vibrational spectra are analyzed and the most probable assignments are proposed for all the fundamentals based on the potential energy distribution.     

Mg8Rh4B — A new type of boron stabilized Ti2Ni structure

The new magnesium rhodium boron compound Mg₈Rh₄B has been synthesized by reaction of the metal powders with crystalline or amorphous boron or the RhB precursor. The crystal structure of Mg₈Rh₄B was solved using single-crystal X-ray diffraction data (space group , , Z=8, 174 reflections, R_F=0.016). The crystal structure can be described as a filled Ti₂Ni type where the interstitial sites 8b (), located at the center of two nested Mg₄Rh₄ tetrahedra, are occupied by boron atoms. Taking into account the absence of the Ti₂Ni-type phase in the binary Mg-Rh system, the boron atoms can be considered as stabilizing this structural motif. From the bonding analysis with the electron localization function the crystal structure is described as covalently bonded [Rh₄B]³⁻ anions, embedded in a cationic magnesium matrix.     

Ce掺杂K2La2Ti3O10催化剂的可见光高效催化制氢的研究

采用高温固相法合成了铈掺杂的K₂La₂Ti₃O₁₀催化剂, 利用X射线衍射(XRD)、紫外-可见漫反射(UV-vis DRS)、透射电镜(TEM)和X射线光电子能谱(XPS)对催化剂进行了表征. 考察了催化剂的可见光催化分解甲醇水溶液制氢的活性, 并对可见光催化机理进行了分析. 研究表明, 铈的掺杂没有改变K₂La₂Ti₃O₁₀的微晶结构, 并使催化剂粒径有所减小. 紫外可见漫反射分析表明禁带宽度为2.3 eV左右, 对可见光具有较高吸收. XPS表明La和Ti为＋3和＋4价, 而Ce则是＋3和＋4的混合价态. 担载2 wt% Pt后, 在可见光下光催化活性大大提高, 当铈的掺杂量为0.5 mol%(即Ce取代La的摩尔百分量)时, 光催化活性达到最大, 产氢速率为0.05 mmol/h; 光照5 h后产氢量为0.22 mmol, 而纯K₂La₂Ti₃O₁₀的产氢量只有0.037 mmol.     

Preparation of Pt/K2La2Ti3O10 and its photo-catalytic activity for hydrogen evolution from methanol water solution

A layered perovskite-type oxide K₂La₂Ti₃O₁₀ was prepared with high-temperature solid-state reaction, and characterized with X-ray diffraction (XRD) and ultraviolet-visible diffuse reflectance spectroscopy (UV-Vis DRS). Platinum was loaded onto K₂La₂Ti₃O₁₀ as a co-catalyst with different methods. The dispersion of platinum on K₂La₂Ti₃O₁₀ was determined with HOT method. The photocatalytic activity of Pt/K₂La₂Ti₃O₁₀ was studied. This catalyst showed much higher activity in hydrogen evolution reaction than Ni/K₂La₂Ti₃O₁₀. The effects of different amounts of loaded platinum and several preparation methods were evaluated. The best achieved hydrogen evolution rate was 233.88 μmol·h⁻¹ by Pt(2%)/K₂La₂Ti₃O₁₀. A possible band structure and mechanism were discussed based on the results.