Deformation behavior of Fe-based bulk metallic glass during nanoindentation

Fe-based bulk metallic glasses (BMGs) normally exhibit super high strength but significant brittleness at ambient temperature. Therefore, it is difficult to investigate the plastic deformation behavior and mechanism in these alloys through conventional tensile and compressive tests due to lack of distinct macroscopic plastic strain. In this work, the deformation behavior of Fe₅₂Cr₁₅Mo₉Er₃C₁₅B₆ BMG was investigated through instrumented nanoindentation and uniaxial compressive tests. The results show that serrated flow, the typical plastic deformation feature of BMGs, could not be found in as-cast and partially crystallized samples during nanoindentation. In addition, the deformation behavior and mechanical properties of the alloy are insensitive to the applied loading rate. The mechanism for the appearance of the peculiar deformation behavior in the Fe-based BMG is discussed in terms of the temporal and spatial characteristics of shear banding during nanoindentation. Supported by the National Natural Science Foundation of China (Grant Nos 50571109, 10572142 and 56771102) and the National Basic Research Program of China (973 Program)(Grant No 2007CB613900)     

Pd-Si binary bulk metallic glass

Pd_80+x Si_20−x (x = 0, 1, and 2) binary metallic glasses with the diameter ranging from 7 to 8 mm were prepared by a combination of fluxing and water quenching or air cooling. Thermal analysis results show that with increasing Si content, the glass transition temperature T _g, the initial crystallization temperature T _x and the onset crystallization temperature T _p of Pd-Si binary glassy alloys increase. Moreover, the supercooled liquid region reaches 61 K. It indicates that Pd-Si binary alloys possess large glass forming ability, which can be greatly improved by fluxing treatment. Supported by the National Basic Research Program of China (Grant No. 2007CB613905) and the National Natural Science Foundation of China (Grant Nos. 50671050 and 50431030)     

Compressive fracture characteristics of Zr-based bulk metallic glass

The compressive fracture characteristics of Zr-based bulk metallic glass under uniaxial compression tests are studied.The zigzag rheological behavior is observed in the compression stress-strain curves of amorphous alloys.At room temperature the uniaxial compression fracture takes place along the plane which is at a 45-degree angle to the direction of the compressive stress.The microstructure of a typical fracture pattern is the vein network.A unique,finger-like vein pattern is found to exist at the fractur...     

退火态Zr55A110Ni5Cu30块体非晶合金在轧制过程中的自由体积演化

将Zr55All0Ni5Cu30块体非晶合金在715K等温退火30min,引入少量纳米晶,然后于室温以不同的应变速率进行轧制,用差示扫描量热仪考察不同应变量样品的热稳定性和自由体积演化．结果表明：即使轧制到95％的最大应变量,样品的热稳定性也几乎没有发生改变．在各种应变速率下,随着应变量的增加,自由体积含量持续上升．但随着应变速率的增加,相同应变量下自由体积的含量先上升后降低,该规律与单一非晶态结构合金在塑性变形过程中自由体积的变化情况截然不同．     

新型Pr基大块非晶及其特性研究

用铜模吸铸法获得了直径为5mm的一种新的Pr基大块非晶.与以往其他稀土-过渡金属(RE-TM)大块非晶不同的是，这种新的Pr基大块非晶具有明显的玻璃转变和稳定的过冷液相区，且其玻璃转变温度在目前已知的大块非晶中是最低的，T_g=409K.研究了该大块非晶的玻璃转变动力学，并给出了Kauzmann温度T_k、Vogel-Fulcher温度T⁰_g及脆性参数m等重要参数. 关键词： 大块非晶 玻璃转变 脆性参数m     

Fracture characteristics of bulk metallic glass under high speed impact

High speed impact experiments of rectangular plate-shaped Zr₄₁Ti₁₄Cu_12.5Ni₁₀Be_22.5 bulk metallic glass (BMG) were performed using a two-stage light gas gun. Under spherical shock waves with impact velocities ranging from 0.503 km/s to 4.917 km/s, obvious traces of laminated spallation at the back (free) surface and melting (liquid droplets) at the impact point were observed. The angles about 0?, 17?, 36?, and 90? to the shocking direction were shown in the internal samples because of the interaction between the compressive shock waves and the rarefaction waves. The compressive normal stress was found to induce the consequent temperature rise in the core of the shear band.     

块体金属玻璃Zr_(48)Nb_8Cu_(12)Fe_8Be_(24)低温电阻的研究

对新型块体金属玻璃Zr48Nb8Cu12Fe8Be24的低温电阻进行了研究,并用理论模型分析了不同温度区间电阻与温度的关系,由此探讨了此类非晶低温下电子散射机理.由实验数据估算了主要散射机理的贡献. 关键词： 金属玻璃 电阻     

永磁性Pr55Al12Fe30Cu3 大块金属玻璃

报道一个新的Pr55Al12Fe30Cu3 大块金属玻璃.采用铜模吸铸法制备了直径为5 mm、长度达100 mm的Pr55Al12Fe30Cu3 大块金属玻璃.差示扫描量热分析结果表明在该Pr基大块金属玻璃体系具有宽达64 K左右的过冷液相区，而且该合金呈非晶态时的熔化温度要比相应晶态样品的熔化温度高约140 K.磁滞回线测量表明非晶态Pr55Al12Fe30Cu3 块体合金在室温下呈现永磁特性，而完全晶化后样品在室温下呈现软磁特性. 关键词： 大块金属玻璃 玻璃转变 晶化 永磁性     

Zr-based bulk metallic glass as a cylinder material for high pressure apparatuses

Zirconium-based bulk metallic glass (Zr-based BMG) has outstanding properties as a cylinder material for piston-cylinder high pressure apparatuses and is especially useful for neutron scattering. The piston-cylinder consisting of a Zr-based BMG cylinder with outer/inner diameters of 8.8/2.5?mm sustains pressures up to 1.81?GPa and ruptured at 2.0?GPa, with pressure values determined by the superconducting temperature of lead. The neutron attenuation of Zr-based BMG is similar to that of TiZr null-scattering alloy and more transparent than that of CuBe alloy. No contamination of sharp Bragg reflections is observed in the neutron diffraction pattern for Zr-based BMG. The magnetic susceptibility of Zr-based BMG is similar to that of CuBe alloy; this leads to a potential application for measurements of magnetic properties under pressure.     

Isothermal crystallization in Ce70Ga6Cu24 bulk metallic glass

The isothermal crystallization behaviors in a newly developed CeGaCu bulk metallic glass have been investigated through the classic differential scanning calorimeter(DSC) method. It is found that the apparent activation energy(Ea) strongly depends on the fraction(x) of isothermal crystallization. Johnson-Mehl-Avrami(JMA) formula was used to analyze the mechanism of crystallization and the obtained Avrami exponent(n) was discovered to show an obvious correlation with the crystallization fraction x. With the help of the relation between Ea and n, the nucleation and growth activation energies, En and Eg, were estimated to be 214–304 kJ/mol and 91 kJ/mol, respectively. This result suggests that the main energy barrier against crystallization in the present glass should be the nucleation of nucleates, rather than the growth of crystals. Such a large En is also believed to be responsible for the good glass forming ability of the CeGaCu alloy.     

LaGa-based bulk metallic glasses

We report the formation of La Ga-based bulk metallic glasses. Ternary La–Ga–Cu glassy rods of 2–3 mm in diameter can be easily formed in a wide composition range by the conventional copper mold casting method. With minor addition of extra elements such as Co, Ni, Fe, Nb, Y, and Zr, the critical diameter of the full glassy rods of the La–Ga–Cu matrix can be markedly enhanced to at least 5 mm. The characteristics and properties of these new La Ga-based bulk metallic glasses with excellent glass formation ability and low glass transition temperature are model systems for fundamental issues investigation and could have some potential applications in micromachining field.     

Effect of the cooling rate on plastic deformability of a Zr-based bulk metallic glass

The present work found the plastic deformability of Zr65Cu17.5Ni10Al7.5 BMG dependent on the cooling rate during the formation from the molten state alloy. The deformation behavior in the compression test of φ 2 mm Zr65Cu17.5Ni10Al7.5 BMGs as-cast or lathed from different sizes as-cast samples was characterized, and they exhibited different plastic strains. The compressive plastic strain increases with the decreasing diameter of the as-cast specimens, i.e. with increasing the cooling rate. It is suggested that free volume content in the BMGs, which is related to the cooling rate during the rapid solidification, could play an important role in the deformation process of the BMGs.     

A nano-polycrystalline diamond anvil cell with bulk metallic glass cylinder for single-crystal neutron diffraction

ABSTRACT

A high-pressure cell for in-situ single-crystal neutron diffraction was developed. The cell uses nano-polycrystalline diamond anvils in a tubular load frame made of bulk metallic glass which is highly transparent to neutrons and does not produce Bragg reflections. Diffraction peaks from a sample can be measured from almost any direction and the simple geometry of the cell allows accurate attenuation corrections. We demonstrate the operation of the cell by ambient-pressure experiment using a single-crystal of NaCl on the D9 diffractometer at the Institute-Laue-Langevin. A high-pressure experiment was also carried out on a single crystal of ice VII at 2.35?GPa showing the potential to detect weak diffraction spots. The correct integration of weak reflections together with the simple attenuation correction will help to carry out precise structure analysis and address new scientific problems using neutron diffraction.     

Deformation behavior of Zr-based bulk metallic glass and composite in the supercooled liquid region

A Zr-based bulk metallic glass (BMG) with a composition of (Zr₇₅Cu₂₅)_78.5Ta₄Ni₁₀Al_7.5 and a bulk metallic glass matrix composite (BMGC) with a composition of (Zr₇₅Cu₂₅)_74.5Ta₈Ni₁₀Al_7.5 have been prepared by copper-mold casting. The compressive deformation behavior of the BMG and BMGC was investigated in the supercooled region at different temperatures and various strain rates ranging from 8×10⁻⁴ s⁻¹ to 8×10⁻² s⁻¹. It was found that both the strain rate and test temperature significantly affect the deformation behavior of the two alloys. The deformation follows Newtonian flow at low strain rates but non-Newtonian flow at high strain rates. The deformation mechanism for the two kinds of alloys was discussed in terms of the transition state theory. Supported by the National Natural Science Foundation of China (grant Nos. 50471060 and 50635020)     

退火态Zr55Al10Ni5Cu30块体非晶合金在轧制过程中的自由体积演化

将Zr₅₅Al₁₀Ni₅Cu₃₀块体非晶合金在715 K等温退火30 min, 引入少量纳米晶, 然后于室温以不同的应变速率进行轧制, 用差示扫描量热仪考察不同应变量样品的热稳定性和自由体积演化. 结果表明:即使轧制到95%的最大应变量, 样品的热稳定性也几乎没有发生改变. 在各种应变速率下, 随着应变量的增加, 自由体积含量持续上升. 但随着应变速率的增加, 相同应变量下自由体积的含量先上升后降低, 该规律与单一非晶态结构合金在塑性变形过程中自由体积的变化情况截然不同.     

大块非晶临界冷却速率的非等温转变计算模型

在非等温转变理论以及非稳态形核理论基础上提出了计算大块非晶合金连续冷却转变曲线和 临界冷却速率的新模型,以用于评估合金的非晶形成能力. 依据此模型对Zr基和Pd基8种合金 进行了计算，计算结果与实验值符合较好. 计算结果表明，影响临界冷却速率的主要因素为 黏度、临界形核功和临界结晶分数. 随着黏度增大，临界冷却速率降低；随临界形核功增大 ，临界冷却速率急剧降低；随临界结晶分数增大，临界冷却速率起初降低较快，达到一定程 度后下降速率趋于缓慢. 关键词： 临界冷却速率 非晶形成能力 大块非晶 连续冷却转变曲线     

永磁性大块金属玻璃Nd60Al10Fe20Co10低温磁性的研究

研究了Nd6 0 Al1 0 Fe2 0 Co1 0 大块金属玻璃磁性随温度的变化关系 ,结果表明Nd6 0 Al1 0 Fe2 0 Co1 0 在室温下表现为永磁性 ,随着温度的降低 ,矫顽力和磁滞回线形状都有很大的变化 .交流磁化率在 18K左右出现尖峰而且峰值温度随频率变化 ,表明该大块非晶体系中存在自旋玻璃态     

Zr48Cu45Al7大块金属玻璃的原子结构研究

应用同步辐射X射线衍射(XRD)和广延X射线吸收精细结构边方法(EXAFS),结合反蒙特卡罗(RMC)拟合、Voronoi分形技术等对Zr₅₀Cu₅₀二元和Zr₄₈Cu₄₅Al₇三元金属玻璃材料的微观结构进行了系统的研究.结果表明:ZrCuAl三元金属玻璃中Al原子与Zr原子、Cu原子之间存在强相互作用,表现为键长的明显缩短,导致其微观结构中的Voronoi团簇体积普遍小于Zr_{50关键词： 大块金属玻璃 原子结构 玻璃形成能力 同步辐射技术}     

Fe-B-Y-Nb bulk metallic glasses in relation to clusters

Bulk metallic glass formations in the Fe-B-Y-Nb quaternary alloy system were investigated by using the cluster line rule in combination with the minor alloying principle. The Fe-B-Y ternary system was selected as the basic system and the intersections of cluster lines were taken as the basic ternary compositions. The basic compositions were further alloyed with minor amounts of Nb. After 3–5 at.% Nb was added, the basic composition Fe_68.6B_25.7Y_5.7, which was developed from the most densely packed cluster Fe₈B₃, formed 3 mm bulk metallic glasses. These quaternary bulk metallic glasses (Fe_68.6B_25.7Y_5.7)_100−x Nb _x (x = 3–5 at.%) are expressed approximately with a unified simple composition formula: (Fe₈B₃)₁(Y, Nb)₁. The (Fe_68.6B_25.7Y_5.7)₉₇Nb₃ bulk metallic glass has the largest glass forming ability with the following characteristic parameters T _g = 907 K, T _x = 1006 K, T _g/T _l = 0.644, γ = 0.434, and longness t = 22 mm. The combination of the cluster line rule and the minor-alloying principle is a promising new route towards the quantitative composition design of multi-component metallic glasses. Supported by the National Natural Science Foundation of China (Grant Nos. 50671018, 50631010 and 50401020) and the National Basic Research Program of China (Grant No. 2007CB613902)     

压力下Nd60Al10Fe20Co10块体金属玻璃的弹性行为

室温下在等静压最高达～0.5GPa的条件下，利用超声回波技术测量了超声波横波和纵波在Nd₆₀Al₁₀Fe₂₀Co₁₀块体金属玻璃中的传播时间来确定横波和纵波速度.测量时所采用的超声波频率为10MHz.利用所测量的数据，建立了超声波波速、样品的密度、弹性模量以及Debye温度等与所施加的压力之间的相互关系.并且推导出Murnaghan状态方程.另外，基于非晶态与晶态物理性能的相似性，对此块体非晶的压缩曲线、弹性常数和Debye温度等进行了理论计算，结果表明Nd₆₀Al₁₀Fe₂₀Co₁₀块体金属玻璃的弹性性能与其组成的元素有着密切的关系. 关键词： 块体金属玻璃 弹性性能 等静压