LiF-KCl熔盐溶液的Monte Carlo法计算机模拟研究——Ⅱ.熔体结构与物性的关系

本文用Monte Carlo法对互易盐系LiF-KCl熔盐溶液的局部结构作了计算机模拟。计算了该熔盐溶液的总势能和势能分布。在1200K模拟温度下,该熔盐溶液中大部分离子组成各种形式的离子团。根据模拟的互易盐系熔盐溶液模型,讨论了熔体局部结构和物性之间的关系。     

LiF-KCl熔盐溶液的Monte Carlo法计算机模拟研究——Ⅰ.径向分布函数和热力学性质

本文用Monte Carlo法对互易盐系LiF—KCl熔盐溶液的结构和性质进行了计算机模拟。计算了各离子的偏径向分布函数和摩尔容积、热焓、混合热等热力学性质。若干计算结果与实测值大体相符,计算表明:LiF—KCl熔盐混合后,Li~+,F~-离子间平均距离显著减小,熔体内自由体积作不均匀分布。本文还讨论了这一结构特点的成因和意义。     

NaCl-NaBr系熔盐溶液的分子动力学研究

近年来，用计算机模拟馆公的结构和性质的研究已有较大进展[1，2]．但研究工作多集中在有阴离子相同、阳离子不同的盐组成的“同阴离子系”（commonanionsystems），而对由阳离子相同、阴离子不同的盐组成的“同阳离子系”（commoncationsystems）熔盐溶液则甚少研究．鉴于自然界和生产中同阳离子系也不乏实例，建立同阳离子系熔盐溶液的理论屯有必要．为止匕我们先选择NaCI－NaBr系熔盐溶液（同阳离子系的一个最简单的典型）为对象，开展分子动力学方法计算机模拟研究．1模型和计算方法采用标准文献中的计算模拟和方法，离子间劳用Fumi-…     

LiF-KF熔盐溶液局部结构的计算机模拟研究

本文用Monte Carlo法对同离子系LiF-KF熔盐溶液的局部结构进行了计算机模拟,介绍了计算方法和模型。计算了LiF, KF及Lif-KF混合前后正-正离子, 正-负离子, 负-负离子间位能变化, 各类离子的近邻离子排布规律, 以及各种形式离子团的组成比例。本文还讨论了在熔盐瞬时结构中存在的静电场的微区涨落。     

熔融LiF、KCl和互易系LiF-KCl的分子动力学模拟计算

我们用分子动力学方法模拟了1200K的LiF、KCl和LiF-KCl熔盐系的结构和性质,包括热力学性质、结构动力学性质和输运性质,并对其瞬态图象进行了分析。计算中取Fumi-Tosi势为离子间有效对势,所用程序MDIONS由中科院理论物理研究所的CPC库提供。模拟系统采用立方元胞,内含216个离子,正负离子各半。互易系     

ZnCI~2-KCI系溶液的分子动力学模拟

用Busing离子间势,对ZnCI~2-KCI 系熔盐液的结构作分子动力学计算机模拟研究,模拟结果与中子衍射,X射线衍射,Raman光谱和红外光谱的若干结构相符.     

ZnCI~2-KCI系溶液的分子动力学模拟

用Busing离子间势,对ZnCI~2-KCI 系熔盐液的结构作分子动力学计算机模拟研究,模拟结果与中子衍射,X射线衍射,Raman光谱和红外光谱的若干结构相符.     

熔融NaCaF3、Na2CaF4和Na3CaF5的分子动力学模拟

通过分子动力学模拟，研究了熔盐溶液NaCaF_3、Na_2CaF_4和Na_4CaF_5体系，模拟表明，三种二元混合系的径向分布函数十分接近．由模拟所得到的摩尔混合焓很好地与实验值一致．混合焓与Na~+离子势阱深度之间表现出很好的线性关系．模拟表明，在Na_2CaF_4体系中，即NaF-CaF_2二元系处于低共熔混合组分比NaF:CaF_2＝2:1时，Na~+，Ca~(2+)和F~-离子的自扩散系数出现很大的反常．     

ZnCl2熔盐的分子动力学模拟

近年来，若干作者根据几种粒子间函数，对ZnCl2熔盐结构做过分子动力学模拟［1－3］其出的Zn－Cl和Cl－Cl离子间的偏径向分布函数与中子衍射实测值符合较好，但Zn－Zn离子间距以及Zn－Zn间配位数计算值多偏高．鉴于Busing势函数在多价卤化物馆盐的分子动力学计算中应用效果较好[4],我们试用Busing势函数为基础对ZnCl2熔盐结构和能量做分子动力学计算．1研究方法计算所用粒子势为Busing势函数此处，Zi为离子的电行数（ZZn。＋＝2，Zcl－＝1），几；是离子有效半径，人为＊离子的“硬度”参数·据文献问，f二0．005071，尸zn。十二0．…     

电解质溶液自扩散系数的布朗动力学模拟

采用布朗动力学方法对电解质溶液进行了模拟,在传统布朗动力学的基础上综合考虑了流体力学的影响,并且引入SmartMonteCarlo方法的接受概率,避免了离子不现实的移动和位型重叠,这样不仅可以将模拟过程中的时间步长大幅度提高,而且还可使溶质在相空间的演化过程更接近实际.模拟过程以电解质溶液的原始模型为基础,将溶剂看作连续介质,溶质分子之间的相互作用采用软核加静电的势能函数模型,长程静电力采用Ewald加和的处理方法.模拟得到KCl和NaCl溶液的径向分布函数g+-(r),g++(r)和g--(r),并与文献中HNC计算以及模拟的结果进行比较,使用推广的Green-Kubo公式模拟计算溶液中各种离子的自扩散性质,计算结果与实验数据吻合良好.     

南瓜籽烘烤前后化学成分的分析

对烘烤前后南瓜籽中的化学成分进行分析并对比。采用同时蒸馏萃取装置萃取南瓜籽中的挥发性成分,采取超临界CO2萃取技术萃取南瓜籽油脂,并将其分为酸、碱、中性三个部分,用气相色谱-质谱联用方法分析其中化学成分并进行对比。结果表明,南瓜籽挥发性成分中含有多种醛类和酯类化合物,烘烤后产生了大量的烷基吡嗪,其在碱性部分中的相对含量比烘烤前提高14倍多,不饱和醛类化合物含量也有明显提高。南瓜籽油脂中的主要化学成分是油酸、亚油酸及其酯类。还含有生物活性功能成分如植物甾醇、角鲨烯和维生素E等。烘烤后除角鲨烯含量有所降低,维生素E、植物甾醇、亚麻酸等均有提高。     

Synthesis,characterization, and antimicrobial activity of some novel poly(ether ketone)s

Low molecular weight poly(ether ketone)s were synthesized from phenol, 1,4‐phenylenedioxy diacetylchloride, chloroacetylchloride, and dichloroalkanes [1,2‐dichloroethane and dichloromethane] by a Friedel–Crafts reaction with anhydrous aluminum chloride as a catalyst and carbon disulfide as a solvent. The conditions for the preparation of the poly(ether ketone)s and the chlorine contents obtained with the Carius method were examined, and a reaction scheme for each resin was established. The molecular weights and polydispersities of the resins were obtained by gel permeation chromatography. The polyketones were characterized by IR spectroscopy. The characteristic frequencies due to different functional groups were assigned. The thermal properties of the resins were studied with thermogravimetry and differential scanning calorimetry. The characteristic temperatures of thermal degradation for the poly(ether ketone)s were evaluated with thermogravimetric analysis. The kinetic parameters for the decomposition reactions of the resins were obtained with Broido and Doyle's method, and the heats of fusion were obtained from differential scanning calorimetry thermograms. The polyketones were thermally stable up to 200 °C. All the polyketones were tested for their microbial properties against bacteria, fungi, and yeast. The effect of poly(ether ketone)s on the growth of these microorganisms was investigated, and the polyketones were found to inhibit the growth of the microorganisms to a considerable extent. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2335–2344, 2003     

ADSORPTION OF PHENOL AND NITROPHENOLS ON A HYPERCROSSLINKED POLYMERIC ADSORBENT

The adsorption of phenol and nitrophenols on hypercrosslinked polymeric adsorbent wasstudied as a function of the solution concentration and temperature. Adsorption isotherms of phenoland nitrophenols on hypercrosslinked resin were determined. These isotherms were modeledaccording to the Freundlich adsorption isotherm. The isotherms for phenol and nitrophenols onhypercrosslinked resin were assigned as L curves. Thermodynamic parameters were calculated for allphenol and nitrophenols. The kinetics experiment results showed that the adsorption rates were of thefirst-order kinetics. The rate constants at 303K were calculated.     

Effect of gallium, aluminium, and chromium on silica supported V-Mg-O catalysts during oxidative dehydrogenation of propane: Kinetic study

The oxidative dehydrogenation （ODH） of propane was conducted on gallium, aluminum, and chromium doped Si30VMgO catalysts. On doping, the concentrations of the phases responsible for the activity and selectivity increased in their concentrations. The reaction studies were conducted in a tubular steel reactor at temperatures of 753, 783, 813, and 843 K and atmospheric pressure. The total flow rates of the feed were chosen as 30, 40, 50, and 60 ml/min. The propane to oxygen ratios were chosen at 1 ： 1, 2 ： 1, and 3 ： 1, respectively. The effect of various dopants on the activity and selectivity of the catalysts was studied. Deactivation studies were conducted over all the catalysts. The kinetic data were analyzed in terms of power law models and Langmuir-Hinshelwood （LH） models. The kinetic data results were analyzed by comparing the effect of dopants. Statistical model discrimination was done for the proposed models. AIC and BIC criteria were used for discrimination of the models.     

CH自由基和NO~2反应研究: I. 反应的热力学计算

探讨了CH自由基与NO~2反应的可能路径,通过计算确定了反应物,产物和稳定中间体的电子状态和平衡构型,并运用Gaussian-3方法和MRCISD方法对可能的反应路径进行了热力学计算。在多数情况下与实验值符合较好。对于个别与理论计算差别较大的实验值进行了评述。     

废弃油脂生产生物柴油的研究进展

简单介绍了生物柴油的生产原料,综述了用废弃油脂生产生物柴油的现状和方法。废弃油脂生产生物柴油的方法主要有物理法和化学法,物理法主要有掺和法和微乳法,化学法主要有热裂解法和酯交换法。目前生产中采用化学法的酯交换法、以酸碱两步催化法的工艺为主,而生物酶法和超临界法是研究热点。     

烟草制品及烟气中重金属检测方法的研究进展

从烟草制品及其烟气的前处理方法和检测方法两方面对烟草中重金属含量测定的研究进展进行了综述。重点介绍了湿法消解、微波消解、萃取和悬浮进样技术等样品前处理方法,以及原子光谱法、质谱法和液相色谱法等测定方法。列举了不同方法的灵敏度、准确性和适用范围,对各方法的优缺点进行了比较,并对烟草中重金属检测方法的发展进行了展望。     

离聚体水基微乳液化的研究——聚苯乙烯离聚体微乳化过程相反转的表征

以乙酰磺酸为磺化剂制备磺化度为３～１５ｍｏｌ％的磺化聚苯乙烯（ＳＰＳ）并中和成盐．在一定的温度和搅拌速率下，加水将ＳＰＳ乳化成水包油的稳定水基微乳液．用乳化过程中体系电导率和粘度的变化表征了乳化相反转过程．研究了溶剂的极性和离子含量对聚苯乙烯离聚体溶液可乳化性和乳化过程及乳液稳定性的影响．     

气相色谱-质谱联用法测定橡胶制品中多环芳烃（蒽）含量不确定度评定

目的对气相色谱-质谱联用仪法测定橡胶制品中多环芳烃（蒽）含量不确定度进行评定,确定影响不确定度的关键因素。方法依据《ZEK01.4-2008 GS认证过程中PAHs的测试和验证》,使用气相色谱-质谱联用仪法测定橡胶制品中多环芳烃（蒽）含量,并对结果的不确定度进行评定,分析影响测量不确定度的各个因素,对各个分量进行计算和合成。结果扩展不确定度U=5.7 mg/kg,置信概率95%。结论该实验的不确定度主要影响因素是曲线校准。     

ADSORPTION OF PHENOL AND NITROPHENOLS ON A HYPERCROSSLINKED POLYMERIC ADSORBENT

1. INTRODUCTION Nitrophenols are versatile raw materials in chemical industry and used in a great diversity of applications such as herbicides, insecticides and bactericides. Due to their extreme toxicity and adverse effect upon human and biota at very l…