飞秒紫外激光脉冲振荡的实验研究

本文讨论了采用空间光脉冲光谱的啁啾特性和选择聚焦透镜焦距相结合的技术大大提高二次谐波转换效率和产生紫外飞秒光脉冲的实验研究.采用一类相位匹配的BBO晶体,当飞秒钛宝石光脉冲平均功率为560mW时,二次谐波输出功率为352mW,二次谐波转换效率高达63%;采用一类相位匹配的LBO晶体时,获得高光束质量的倍频蓝光输出,输出平均功率为170mW,转换效率大于30%.运用LBO倍频产生的蓝光脉冲和剩余的基频光脉冲进行了三次谐波的振荡研究.三倍频晶体采用BBO,通过优化设计倍频光与基频光之间的空间模匹配及精确时间延迟,得到飞秒紫外光输出,输出功率为2mW,中心波长约为280nm,重复率为100MHz.     

CONTINUOUS-WAVE LASER OSCILLATION OF Yb:FAP CRYSTALS AT A WAVELENGTH OF 1043nm

A continuous-wave laser oscillation was demonstrated with a Yb-doped fluorapatite (FAP) crystal pumped with a 905 nm Ti:sapphire laser. The output characteristics for different output couplers were investigated. A maximum power of 67mW at a 1043nm wavelength was obtained with 10% output coupler, pumped by a Ti:sapphire laser with 910mW power. This corresponds to a slope efficiency of 26.5%.     

高效全固化紫外四倍频激光器的研究

用半导体激光器抽运的调Q YLF倍频激光器抽运掺钛蓝宝石激光器，用LBO晶体在腔内产生二次谐波，再聚焦到BBO晶体上产生四次谐波深紫外激光。为了提高谐波转换效率，在腔内分别插入了单片、组合双折射滤光片和聚焦透镜，在平均功率为3.6W，波长为527nm的抽运光下得到410mW，417nm的蓝光。用长焦距的透镜聚焦二次谐波，得到34mW，208nm的紫外脉冲激光。从实验上详细研究了基频光的线宽对二次谐波效率的影响，二次谐波的线宽对四次谐波效率的影响、基频光的波长对四次谐波产生效率的影响。全面地分析了单片和组合大拆射滤光片及抽运功率对钛蓝宝石激光器基频光的脉宽、线宽等参量的影响。     

Relative carrier-envelope phase dynamics between passively synchronized Ti:sapphire and Cr:forsterite lasers

We observed and measured the relative carrier-envelope phase difference per round trip between synchronized femtosecond Ti:sapphire and Cr:forsterite mode-locked lasers. The relative carrier-envelope phase slip was directly recorded by heterodyning of the Cr:forsterite laser with the supercontinuum from the Ti:sapphire laser. We also obtained another phase relation by superimposing the third harmonic of the Cr:forsterite laser with the second harmonic of the Ti:sapphire laser. In the latter case we obtained a stable beat signal with a signal-to-noise ratio larger than 30 dB and found a dependence of the beat frequency on the cavity length.     

无展宽器的高重复率钛宝石啁啾飞秒脉冲再生放大器的研究

通过优化放大腔结构参数和采用高光束质量的泵浦激光,依靠放大器腔内各个元件的色散展宽种子脉冲, 用钛宝石作为增益介质, 在低泵浦能量下, 实现了高光束质量,高稳定的中等能量的高重复率飞秒脉冲再生放大. 将钛宝石晶体离焦放置,有效的避免了光学损伤. 在1.1 mJ的绿光泵浦下, 获得了2 ps, 120 μJ, 重复频率为1 KHz, 光谱带宽7.8 nm的放大脉冲, 用石英棱镜对压缩可得到130 fs的激光脉冲.     

钛宝石泵浦的Yb:YAG晶体的激光性能

测量了Yb:YAG晶体的光谱特性,用Ar⁺离子泵浦钛宝石激光器作为泵浦源泵浦Yb:YAG晶体,采用平平腔设计,当输出耦合镜T_1.053μm=4.26%,泵浦功率为1410mW时,得到320mW1.053μm的高效CW激光输出,斜率效率为54%,外推阈值功率为203mW。     

Generation of 7-fs laser pulse directly from a compact Ti:sapphire laser with chirped mirrors

A compact femtosecond Ti:sapphire laser resonator consisting of three chirped mirrors and one output coupler was designed. By accurately balancing the intra- cavity dispersions between Ti:sapphire crystal, air and chirped mirrors, we directly generated the laser pulse shorter than 7 fs at the average power of 340 mW with 3.1 W pump. The repetition rate of the laser oscillator is 173 MHz at the centre wavelength of 791 nm, and the ultrabroaden spectrum covers from 600 nm to 1000 nm. To the best of our knowledge, this is the simplest laser resonator capable of generating sub-10 fs laser pulse.     

自锁模钛宝石激光器谐振腔的像差研究

论述自锁模钛宝石激光器谐振腔的像差补偿问题，分析了“Ｘ”型与“Ｚ”型谐振腔彗差的大小，由此对这两种腔作出比较，指出“Ｘ”型腔的优点，在这样设计的激光器上，获得了１９ｆｓ激光脉冲输出，功率为３２０ｍＷ，中心波长为７８４ｎｍ，全半宽度为４２ｎｍ。     

Low-threshold, Self-frequency Doubling Laser Performance of Nd:YCOB at Different Phase-matching Directions

１　Ｉｎｔｒｏｄｕｃｔｉｏｎ　　Ｉｎｒｅｃｅｎｔｙｅａｒｓ,ｃｏｍｐａｃｔｖｉｓｉｂｌｅｌａｓｅｒｓｈａｖｅｂｅｅｎｗｉｄｅｌｙｕｓｅｄｉｎｔｈｅｆｉｅｌｄｓｏｆｉｎｄｕｓｔｒｙ,ｍｅｄｉｃｉｎｅ,ｍｉｌｉｔａｒｙ,ｂｉｏｌｏｇｙ,ｓｃｉｅｎｔｉｆｉｃｒｅｓｅａｒｃｈａｎｄｅｎｔｅｒｔａｉｎｍｅｎｔ．Ｌａｓｅｒｄｉｏｄｅｐｕｍｐｅｄ,ｉｎｔｒａｃａｖｉｔｙｆｒｅｑｕｅｎｃｙｄｏｕｂｌｅｄｓｏｌｉｄｓｔａｔｅｌａｓｅｒｓａｒｅｅｘｔｅｎｓｉｖｅｌｙｕｓｅｄａｓｖｉｓｉｂｌｅｓｏｕｒｃｅｂｅｃ…     

飞秒激光作用下光学玻璃和激光玻璃的光致暗化及其ESR研究

报道了多种商用光学玻璃和激光玻璃在800nm,120fs,1kHz脉冲激光作用下,产生光致暗化的阈值.并对照射前后的玻璃进行ESR分析,结果表明,光致暗化是由于玻璃内生成空穴捕获型色心的结果.认为玻璃在800nm飞秒激光照射后所产生的色心来源于玻璃的多光子吸收 关键词： 阈值 暗化 玻璃 飞秒激光 ESR     

Influence of laser power on deposition of the chromium atomic beam in laser standing wave

One-dimensional deposition of collimated Cr atomic beam focused by a near-resonant Gaussian standing-laser field with wavelength of 425.55 nm is examined from particle-optics approach by using an adaptive step size, fourth-order Runge-Kutta type algorithm. The influence of laser power on deposition of atoms in laser standing wave is discussed and the simulative result shows that the FWHM of nanometer stripe is 102 nm and contrast is 2:1 with laser power equal to 3 mW, the FWHM is 1.2 nm and contrast is 32:1 with laser power equal to 16 mW, but with laser power increase, equal to 50 mW, the nonmeter structure forms the multi-crests and exacerbates. Supported by the Science Foundation of Guangxi Education Department (Grant No. 200807MS006)     

高效连续波钛宝石激光器的优化设计及实验研究

运用ABCD律及自再现条件对钛宝石线性腔的折叠角进行了优化,从而大大提高了钛宝石晶体中光束束腰的耦合效率同时实验上对连续钛宝石激光器进行了研究,采用20mm长的钛宝石晶体和10%输出耦合镜,并运用优化后的折叠角,最终用全线氩离子激光器泵浦的连续波钛宝石激光器的斜率效率高达34.2%,在泵浦功率为7.7W下,连续钛宝石激光器输出功率达1.89W.     

Generation of two-color femtosecond pulses by self-synchronizing Ti:sapphire and Cr:forsterite lasers

We report a novel technique for the synchronization of two different femtosecond solid-state lasers by crossing of both laser pulses in a Kerr medium. Stable dual-wavelength femtosecond pulses at central wavelengths of 820 and 1250 nm have been obtained. The tolerance of cavity-length mismatch is ~0.6mum , where the pulse widths of the Ti:sapphire and the Cr:forsterite lasers are 18 and 40 fs, respectively, at average powers of 600 and 110 mW. The typical timing jitter derived from the cross correlation is less than 3 fs.     

低阈值掺钛蓝宝石激光器实验研究

结合特殊的谐振腔设计和半导体可饱和吸收镜，建成了一台低阈值的自启动掺钛宝石激光器 . 分别用3％和12％的输出耦合镜，获得了阈值低至390mW和600mW的稳定锁模脉冲输出. 采 用12％输出耦合镜，在12W抽运时，输出平均功率为114mW，对应的典型脉宽为17fs，谱宽 为47nm. 相对于以往的低阈值克尔透镜锁模激光器，锁模工作的范围区域加宽，减小了操作 难度，提高了稳定性. 关键词： 低阈值 半导体可饱和吸收镜 克尔透镜锁模 掺钛蓝宝石激光器     

Three-dimensional reversible laser micromachining with subnanojoule femtosecond pulses based on two-photon photochromism

Three-dimensional reversible laser micromachining of polymer materials based on two-photon photochromism is demonstrated. Unamplified 60-fs, 0.5-nJ pulses of 790-nm Ti:sapphire laser radiation are used to induce a refractive-index change in a polymethyl methacrylate (PMMA) sample doped with spiropyran molecules through a two-photon absorption process. Waveguides are written in the bulk of spiropyran-doped PMMA samples by scanning these samples with respect to a tightly focused Ti:sapphire laser beam. Laser-induced fluorescence is used for on-line monitoring of the laser-micromachining process. The structures written in photochromic samples can be erased and reconfigured due to the reversibility of the photochromic effect. Received: 23 April 2003 / Published online: 6 June 2003 RID="*" ID="*"Corresponding author. Fax: +7-095/939-51-74, E-mail: zheltikov@top.phys.msu.su     

Dye Laser-pumped Cr: LiSrAIF_6 Laser

ＤｙｅＬａｓｅｒ－ｐｕｍｐｅｄＣｒ：ＬｉＳｒＡＩＦ_６Ｌａｓｅｒ￥ＷＵＸｉｎｇ（Ｄｅｐｔ．ｏｆＰｒｅｃｉｓｉｏｎＩｎｓｔｒｕｍｅｎｔＥｎｇｉｎｅｅｒｉｎｇ，Ｔｉａｎｊｉｎ３０００７２，Ｃｈｉｎａ）Ｔ．Ｏｋａｄａ，Ｋ．Ｋａｅｄａ（Ｄｅｐｔ．ｏｆＥｌｅｃ?..     

Efficient, kHz repetition rate, gain-switched Cr:forsterite laser

We have developed a gain-switched room-temperature Cr:forsterite laser operating at repetition rates of between 1 and 34 kHz, and pumped by a continuous wave, Q-switched Nd:YAG laser. With optimised output coupling, an output pulse energy of 52 μJ was measured at 1.5 kHz repetition rate, corresponding to 11% efficiency and 13% slope efficiency. Threshold pulse energy was 53 μJ. Output power of 370 mW was obtained at 10 kHz repetition rate and 4.4 W pump power. Water cooling was not required for repetition rates up to 10 kHz. In a tunable, folded resonator, the Cr:forsterite wavelength tuned between 1173 and 1338 nm. This laser operated with maximum pulse energy of 34 μJ, efficiency of 13%, and power of 307 mW. The laser output was close to diffraction-limited with M² of 1.2. Received: 6 January 1999 / Published online: 29 July 1999     

Inverstigation of Self-Starting for Self-Mode-Locked Ti:Sapphire Laser

ＩｎｖｅｒｓｔｉｇａｔｉｏｎｏｆＳｅｌｆ－ＳｔａｒｔｉｎｇｆｏｒＳｅｌｆ－Ｍｏｄｅ－ＬｏｃｋｅｄＴｉ：ＳａｐｐｈｉｒｅＬａｓｅｒＩｎｖｅｒｓｔｉｇａｔｉｏｎｏｆＳｅｌｆ－ＳｔａｒｔｉｎｇｆｏｒＳｅｌｆ－Ｍｏｄｅ－ＬｏｃｋｅｄＴｉ：ＳａｐｐｈｉｒｅＬａ...     

Improved stabilization of a 1.3 microm femtosecond optical frequency comb by use of a spectrally tailored continuum from a nonlinear fiber grating

We report significant enhancement (+24 dB) of the optical beat note between a 657 nm cw laser and the second-harmonic generation of the tailored continuum at 1314 nm generated with a femtosecond Cr:forsterite laser and a nonlinear fiber Bragg grating. The same continuum is used to stabilize the carrier-envelope offset frequency of the Cr:forsterite femtosecond laser and permits improved optical stabilization of the frequency comb from 1.0 to 2.2 microm. Using a common optical reference at 657 nm, a relative fractional frequency instability of 2.0 x 10(-15) is achieved between the repetition rates of Cr:forsterite and Ti:sapphire laser systems in 10 s averaging time. The fractional frequency offset between the optically stabilized frequency combs of the Cr:forsterite and Ti:sapphire lasers is +/-(0.024 +/- 6.1) x 10(-17).     

37 fs、 0.94 μm钛宝石自锁模激光器的研究

报道了低增益区Ｔｉ＾３＋：Ａｌ２Ｏ３红外飞秒激光器的连续及自锁模运转情况,采用四镜折叠像散补偿腔,对于连续波运转,泵浦阈值功率为５．８Ｗ,其调谐范围为０．９－０．９７μｍ。