Effects of output coupler reflectivity on the performance of a linear cavity Brillouin/erbium fiber laser

The effect of output coupler reflectivity (or output coupling ratio) on the performance of a linear cavity Brillouin/erbium fiber laser (BEFL) is demonstrated. The operating wavelength, output laser power and number of channels vary with changes in the coupling ratio in the linear cavity system. The optimum BEFL operation is obtained with an output coupling of 40%, i.e., 60% of the laser power is allowed to oscillate in the cavity. A stable laser comb consisting of up to 40 channels with line spacings of approximately 0.09 nm are obtained at the Brillouin pump and 980 nm pump with powers of 2.5 mW and 100 mW, respectively. The linear cavity BEFL has the potential to be used in inexpensive wavelength division multiplexing system.      

Bi-directional dual-wavelength Brillouin lasing in a hybrid fiber ring cavity

In this paper, a novel Brillouin fiber laser (BFL) is proposed based on the hybrid fiber ring cavity composed of two types of fibers with different Brillouin shifts. Single mode fiber (SMF) and truewave fiber (TWF) are used in our experiments. Bi-directional dual-wavelength Brillouin lasing is achieved in the hybrid fiber ring cavity. The lasing lights along the two directions come from the Stokes waves generated in the two fibers, respectively, with different Brillouin shifts, however, they share the same fiber ring cavity. The BFL based on the hybrid fiber ring cavity provides a simple possible way to realize Brillouin fiber optical gyroscopes (BFOGs) without lock-in effect.     

Hybrid Brillouin/Erbium fibre laser in a linear cavity for multi-wavelength communication systems

A novel technique of producing multiwavelength laser source was described utilising a linear cavity of hybrid Brillouin/Erbium fibre laser (BEFL). Twenty-two stable output lasers with 10.88 GHz line spacing were obtained from this architecture at 1557.5 nm that was at the peak of Erbium gain. The requirement of an internal feedback that is commonly used in a ring configuration to generate cascaded Brillouin Stokes for multiple wavelengths operation was achieved by the proposed linear cavity design.     

An Efficient Photonic Crystal Fiber-Based Brillouin Erbium Fiber Laser Using a Fiber Bragg Grating for Multi-Wavelength Generation

Abstract

An efficient multi-wavelength Brillouin erbium fiber laser is demonstrated using an improved configuration with a broadband fiber Bragg grating and a piece of photonic crystal fiber. The laser generates more than 55 lines of optical comb with a line spacing of approximately 0.09 nm in a 1,565-5 nm region using pump powers of 3 dBm and 150 mW for the Brillouin and 980-nm pumps, respectively. The Brillouin erbium fiber laser with a fiber Bragg grating's reflectivity of 50% obtained a higher number of comb lines compared to that of 99% reflectivity.     

0.16 nm spaced multi-wavelength Brillouin fiber laser in a figure-of-eight configuration

A stable and compact multi-wavelength Brillouin fiber laser (BFL) operating at room temperature is experimentally demonstrated using a 100 m long photonic crystal fiber (PCF) in conjunction with a figure-of-eight configuration. At a Brillouin pump (BP) level of 15.3 dBm, 7 simultaneous lines with 20 GHz or 0.16 nm line spacing is achieved by removing the odd-order Stokes lines. The anti-Stokes lines are also generated via four wave mixing process in the laser cavity. Compared with the Erbium-based multi-wavelength laser, this BFL has advantages in term of channel spacing and flexibility in the choice of operating wavelength. The output spectrum of the proposed BFL can be tuned by 80 nm, dependent on the availability of an appropriate BP source. The multi-wavelength BFL shows a good stability with power fluctuations of less than 0.5 dB over more than 3 h.     

An Enhanced Bismuth-Based Brillouin/Erbium Fiber Laser with Linear Cavity Configuration

A multi-wavelength Brillouin/erbium-doped fiber laser (BEFL) which operates in 1594 nm region is demonstrated using a 215 cm long Bismuth-based EDF and SMF. Two optical circulators were used at the output ends of the system to form a linear cavity to produce a cascaded Brillouin Stokes and anti-Stokes. A stable output laser comb of more than 20 lines was obtained with a spacing of approximately 0.089 nm at a Brillouin pump power of 4 dBm and two 1,480-nm pumps at powers of 100 mW. The number of lines is relatively higher compared with the ring cavity BEFL.     

Microwave generation using an all polarization-maintaining linear cavity dual-wavelength fiber laser with tunable wavelength spacing

A stable dual-wavelength erbium-doped fiber laser with a linear cavity is formed by a polarization-maintaining uniform fiber Bragg grating (PM-FBG) and a polarization-maintaining linearly chirped fiber Bragg grating (PM-LCFBG), both of which were fabricated on a high-birefringence (Hi-Bi) fiber. Experimental results show stable dual-wavelength lasing operation with a wavelength separation of ∼0.22 nm, which can be tuned down to as small as 0.05 nm and a large optical signal-to-noise ratio (OSNR) of over 40 dB under room-temperature. Microwave signal at frequency of 9.41, 18.03 and 27.46 GHz is achieved by heterodyned the output lasing wavelengths on a photodetector.     

一种新型自激发布里渊掺铒光纤激光器

利用级联的受激布里渊效应,自激发布里渊掺铒光纤激光器可以实现常温下的多波长激光输出。通过在自激发掺铒光纤激光器中引入一个高双折射萨尼亚克(Sagnac)环形滤波器,调节萨尼亚克环形滤波器的偏振控制器(PC),实现了可调谐多波长输出,同时在实验中观测到双布里渊多波长带的现象。研究了这种光纤激光器中萨尼亚克环形滤波器的带宽和980 nm抽运光功率对输出波长数的影响,在萨尼亚克环形滤波器的带宽为83.3 nm以及980 nm抽运光功率为260 mW时,得到了52个间隔为0.088 nm的多波长激光输出。     

Multi-wavelength generation of L-band brillouin/erbium fibre laser

In this paper, the operation of the Brillouin/erbium fibre laser (BEFL) in the long wavelength band (L-band or 1565–1625 nm) is experimentally demonstrated. The Stokes frequency is shifted 10 GHz from its Brillouin pump (BP) from 1598 to 1612 nm for the single wavelength BEFL. Multiple wavelength generation in the BEFL is realised by adding two 3-dB couplers, which are joined in a reverse-S arrangement to take a portion of the generated BEFL signal and re-inject it into the single-mode fibre (SMF) to seed a cascaded BEFL line in the same direction as the first BEFL line. Twenty lines including the anti-Stokes are obtained with a maximum BP and 980-nm pump power of 8.8 and 92 mW, respectively. The L-band BEFL has the potential to be used in future wavelength division multiplexing (WDM) communication system.     

15波长输出的布里渊掺铒光纤激光器

多波长布里渊掺铒光纤激光器是一种新型的多波长光纤激光器,其原理是利用受激布里渊增益和掺铒光纤的线性增益,可以在常温下得到波长间隔约为0．08nm(～10GHz)的多波长输出。报道的布里渊掺铒光纤激光器,在布里渊抽运功率为1．7mW、980nm抽运功率为300mW的情况下得到稳定的15个波长(间隔～10GHz)的输出,这种激光器用作光传感器、光谱分析仪以及密集波分复用系统的光源。实验发现,输出波长的个数随着980nm抽运功率的增大而增加。另外,布里渊掺铒光纤激光器的信号功率主要来自于掺铒光纤的增益,而布里渊增益对它的影响不大。     

Tunable microwave generation based on a Brillouin fiber ring laser and reflected pump

A simple approach for photonic generation of a tunable microwave signal is proposed and successfully demonstrated. By mixing the output from a single-longitudinal-mode Brillouin fiber ring laser with the reflected laser pump at photodetector, a microwave signal at the Brillouin shift can be obtained. Since the Brillouin shift can be changed by tuning the pump wavelength, tunable microwave can be generated. As a result a microwave signal tunable from 10.39 to 10.67 GHz has been achieved, with linewidth less than 600 KHz.     

间隔0.173nm的可调谐多波长布里渊掺铒光纤激光器

使用四端口环行器和可调谐滤波器,设计了一种间隔为双倍布里渊频移的多波长布里渊掺铒光纤激光器.该光纤激光器中使用的四端口环形器可以限制奇次阶斯托克斯光在腔内循环并耦合输出初始泵浦光和偶次阶斯托克斯光,而可调滤波器抑制环形腔所形成的自激振荡模,增加了激发多波长激光的功率,从而增加多波长输出个数及其调谐范围.在布里渊泵浦功率为8dBm、980nm泵浦功率为279mW时,实验获得波长间隔为0.173nm的6个波长的激光输出,输出激光的可调谐范围为28nm.     

单纵模布里渊掺铒光纤激光器的实验研究

提出了一种具有多环形腔(MRC)和光纤布拉格光栅可调谐滤波器(FBG-TF)相结合的单纵模布里渊掺铒光纤激光器(BEDFL).实验中通过观察激光器输出光的拍频信号分析其光谱精细结构,分别讨论了布里渊增益、FBG-TF、MRC对BEDFL单模输出的贡献,给出了激光器的功率特性曲线和波长稳定性测试图.实验得到了在1550 nm处功率为4 dBm,信噪比(SNR)>60 dB,线宽小于1.5 kHz的稳定单纵模输出光.     

Millimeter wave carrier generation based on Brillouin fiber laser with improved tuning capability

An all-optically generated millimeter wave carrier at 21.7 GHz, 43 GHz and 64.45 GHz are experimentally achieved. These frequencies are realized by generating two consecutively laser wavelengths and are detecting on the 70 GHz high-speed photo detector (HSPD). The initial mixing between the Brillouin pump and the second-order Stokes wavelengths is spaced by 0.178 nm. This spacing, which is doubled from an inherently generated Stokes shift, is accomplished through an isolated circulation of the first order Stokes wave in the double Brillouin Stokes shifter (DSBS) built with 25-km single mode fiber. The generated millimeter carrier is measured at 21.7 GHz, 43 GHz and 64.4 GHz achieved with BP power of 11 mW, 30 mW and 47 mW, respectively.     

Threshold characteristics of linear cavity Yb-doped double-clad fiber laser

The threshold characteristics of linear cavity Yb³⁺-doped double-clad fiber laser have been studied theoretically and experimentally. By solving rate equations, the expression for threshold pump power is obtained. The effects of fiber length, mirror reflectivity, pump wavelength, laser wavelength and Yb³⁺ concentration on threshold pump power are discussed. Then, the Yb³⁺-doped double-clad fiber laser with linear cavity is developed. By using various output couplers, threshold pump power has been measured. The experimental results are in accord with theory.     

Numerical analysis of stimulated Brillouin scattering in high-power double-clad fiber lasers

A theoretical analysis of stimulated Brillouin scattering (SBS) in linear cavity Yb³⁺-doped double-clad fiber lasers is presented by solving the steady-state rate equations with the SBS. The effects of cavity length, fiber core diameter, input mirror reflectivity at Stokes wavelength, Yb³⁺ concentration and laser linewidth on the SBS are discussed. Numerical results show that the SBS threshold power can be improved by shortening the cavity length, using large mode area fiber, reducing the input mirror reflectivity at Stokes wavelength, lowering the Yb³⁺ concentration and broadening the laser linewidth, and the influence of the laser linewidth on the SBS threshold power is more noticeable than other system parameters.     

S-band multiwavelength Brillouin Raman Fiber Laser

In this paper we propose and demonstrate an S-band Brillouin-Raman Fiber Laser (BRFL). The S-band BRFL utilizes a Dispersion Compensating Fiber (DCF) as the non-linear gain medium in a linear cavity configuration and amplified by two 1425 nm, 380 mW pumped Raman Fiber Amplifiers (RFAs). A Brillouin Pump (BP) signal of 1515 nm at 12 dBm in power is injected into the setup to generate Stokes lines via the Stimulated Brillouin Scattering (SBS) process. The S-band BRFL is able of generating a Brillouin comb with 32 Stokes lines with a flat peak output power of − 18 dBm. The best BP to Stokes power ratio of the system is determined to be 50:50, while a ratio of 70:30 is observed to generate Stokes with a higher peak power, but at the expense of the number of wavelengths. The S-band BRFL has many potential applications as multiwavelength sources for communications and sensors.     

Modeling of Multi-Wavelength Brillouin Fiber Laser Based on Analytical Solutions in a Linear Cavity

Abstract

In this article, an accurate model of multi-wavelength Brillouin fiber laser is developed by analytically solving cascade-stimulated Brillouin scattering equations in a linear cavity. The dependence of Stokes signal power on the incident pump power and the successive reflected transmitted powers is calculated. Furthermore, an analytical approach that can be used to predict the generated Stokes signals power is derived. Finally, this derived model is checked with experimental results that show significant agreement with the analytical solution of the model.     

Tunable dual wavelength fiber laser incorporating AWG and optical channel selector by controlling the cavity loss

In this paper, we propose and demonstrated a dual wavelength fiber laser (DWFL) based on the use of an erbium doped fiber (EDF) gain medium as well as an 1 × 24 Arrayed Waveguide Grating (AWG) together with two optical channel selectors (OCS) to provide channel spacing tunability. The output power of the two wavelengths is equalized by controlling the cavity loss in the DWFL using two Programmable Optical Attenuators (POAs). The widest spacing obtained from the DWFL is 18.13 nm while the narrowest spacing is 0.8 nm. The DWFL has good stability with only minor power fluctuations of less than 1.5 dB and a Side Mode Suppression Ratio (SMSR) of approximately 69.1 dB with peak fluctuations of less than 2.3 dB.     

Dynamics of Stimulated Brillouin Scattering in a Short and High-Finesse Fiber Fabry-Perot Resonator

We theoretically investigate the dynamics of stimulated Brillouin scattering (SBS) in a short fiber Fabry-Perot resonator with reflection mirrors. The analysis is based on the coherent six-wave model including an optical Kerr effect and the linear cavity detunings for the pump and created Stokes waves are taken into account in the formulation. The instabilities including periodic, quasi-periodic and chaotic oscillations can occur owing to the Kerr effect even if the fiber resonator is so short as to ensure a single longitudinal-mode operation. The threshold power for SBS and the boundary power between the stable and unstable regions are numerically calculated as a function of the amplitude reflectance of mirrors for different cavity detunings. The dynamics of SBS and these two critical powers depend on the amplitude reflectance and the cavity detuning. Although an increase in the mirror reflectance decreases the threshold power for SBS, it may limit the utility of SBS since the stable region is narrow and the output power levels of the pump and Stokes waves are low.