Determination of copper,chromium, manganese and zinc by graphite furnace atomic absorption spectrometry after separation on polyacrylamide modified with nitrilo triacetic acid

A new chelating collector, polyacrylamide modified with nitrilo triacetic acid (NTA) was developed for the separation and preconcentration of copper, chromium, manganese, and zinc prior to their determination by Graphite Furnace Atomic Absorption Spectrometry (GFAAS). The retention and recovery of the analyte elements were investigated by applying batch and column techniques. Cu(II), Cr(III), Mn(II) and Zn(II) were quantitatively retained by the collector at pH 5.5 or above. The chelating kinetics are so fast that in the batch procedure a quantitative separation of the analyte elements can be achieved in a few seconds. Since a very short contact time is enough to retain the analyte elements in column technique, a separation step can be completed quickly by applying fast flow rates in small columns. The elements collected were completely recovered with 2 mol/l of HCl. In the presence of sodium chloride up to 0.5% the analyte elements were quantitatively separated and recovered. Low blank values of the collector is another important advantage.     

Solid-phase extraction of bismuth, lead and nickel from seawater using silica gel modified with 3-aminopropyltriethoxysilane filled in a syringe prior to their determination by graphite furnace atomic absorption spectrometry

In this study, the use of syringe filled with sorbent for the separation and enrichment of bismuth, lead and nickel prior to their analysis by graphite furnace atomic absorption spectrometry was described to substitute for batch and column techniques. The method proposed in this paper was compared with column technique with respect to easiness, fastness, simplicity, recovery and risk of contamination. The syringe was filled with 0.5 g of sorbent and in order to retain the analyte elements, 5 ml of sample solution (pH≥5) was drawn into the syringe to 15 s and discharged again in 15 s. Then, 2.0 M of HCl, as the eluent, was drawn into the syringe and ejected back to desorb the analyte elements. At optimum conditions, the recoveries of Bi, Pb and Ni were 95-99% with relative standard deviations (RSDs) of around ±2%. Detection limit (δ) was 0.5 μg l⁻¹ for Bi, Pb and Ni, respectively. The elements could be concentrated by drawing and discharging several portions of sample successively but eluting only one time. Bi, Pb and Ni added to a seawater sample were quantitatively recovered (>95%) with low RSD values of around ±2-3%. The risk of contamination is less than that with the column technique. In addition, it is much faster, simpler, easier, more practical and handy compared with column technique.     

Preconcentration of trace metal ions by combined complexation-anion exchange : Part 2. Cobalt,zinc, cadmium and lead with 8-hydroxyquinoline-5-sulfonic acid [1]

The ligand, 8-hydroxyquinoline-5-sulfonic acid, forms anionic complexes with cobalt(II), zinc(II), cadmium(II), and lead(II), each resulting complex showing a high affinity for anion-exchange resins. The effect of pH, ligand/metal ratio, volume, and concentration on percent retention of the anionic complexes by an anion-exchange resin are reported. At optimum conditions, all four metals are quantitatively retained by the column. Zinc, cadmium and lead(II) ions are completely eluted with 11 ml or less of 2 M HN0₃; cobalt(II) is totally removed by 12 M HCl and 2 M HNO₃. Concentration enhancements of 100-fold are easily achieved. All four anionic complexes can be left on the column for 7 days and still be quantitatively (99%) recovered. A ligand-loaded resin column can also remove all four metals quantitatively. Distribution coefficients for the metal complexes and their ligand/metal ratios were determined by using batch methods that may also serve as the isolation procedure.     

Reductive coprecipitation as a separation method for the determination of gold,palladium, platinum,rhodium, silver,selenium and tellurium in geological samples by graphite furnace atomic absorption spectrometry

A method for the separation of Au, Pd, Pt, Rh, Ag, Te and Se from geological samples at trace levels is presented. The elements are separated from the matrix after dissolution by reductive coprecipitation using mercury as a collector and tin(II) chloride as a reductant. The efficiency of coprecipitation is studied by varying the acidity of the solutions and the amount of collector. The analyte elements are determined by graphite furnace atomic absorption spectrometry. In the determination of volatile elements (Te, Au and Ag), matrix modification with iridium is used. Selenium is determined with a mixed matrix modifier containing ascorbic acid and iridium. The method is tested by analysing geochemical reference samples.     

Novel solid-phase extraction and preconcentration technique coupled with ICP-AES for the determination of Cr(III), Ni(II), and Zn(II) in various water samples

Newly synthesized 2-propylpiperidine-1-carbodithioate (2-PPC) was used for the extraction of Cr(III), Ni(II), and Zn(II) from various water samples. In the present investigation, the use of a syringe loaded with sorbent for the separation and enrichment of Cr(III), Ni(II), and Zn(II) prior to their determination by inductively coupled plasma-atomic emission spectrometry (ICP-AES) was proposed to substitute the batch and column techniques. The described method was compared with the column technique with respect to fastness, simplicity, recovery, and risk of contamination. The syringe was loaded with 1.0 g of sorbent in order to retain the analyte elements. Next, 7.0 mL of sample solution (pH 5.0 ± 0.2) was drawn into the syringe in 15 s and discharged over 15 s. Then, an eluent (3.0 M HCl) was drawn into the syringe and ejected back to desorb the analyte elements. At the optimum conditions, the percentage recoveries of Cr(III), Ni(II), and Zn(II) were in the range of 94.50 to 99.62% with a standard deviation (S.D.) of 0.03%. The elements could be concentrated by drawing and discharging several portions of sample successively and eluting only one time. The detailed study of various interferences proved the method to be highly selective. The risk of contamination is less than that with the column technique. The method was successfully applied to the determination of Cr(III), Ni(II), and Zn(II) in spiked and natural water samples. The results obtained are in good agreement with those obtained by the reported methods at the 95% confidence level. The text was submitted by the authors in English.     

Histidine as the functional group for a chelating ion exchanger

In the chelating ion exchanger synthesized, the amino group of histidine is attached chemically via the azide method to the carboxyl group of Amberlite IRC-50. A flow system based on a spectrophotometric detector, with 4-(2-pyridylazo) resorcinol as reagent, is described for fast assays of eluted cations. The pH dependence of the metal extraction is reported for Ag(I), Au(III), Cu(II), Fe(III), Hg(II), Ni(II) and Zn(II) ions. The resin exhibits no affinity for the alkali or alkaline earth metals. The uptake of traces of the specified elements from synthetic samples by a short (90 mm) column of the histidine-containing resin was in the range 94–100% and the retained metals were readily eluted by means of 2 M hydrochloric or hydrobromic acid. In column operation, mercury was quantitatively recovered even in the presence of large excesses of various ligands. The recoveries of the trace metals were good at the usual pH of natural waters.     

Determination of lead, copper and manganese by graphite furnace atomic absorption spectrometry after separation/concentration using a water-soluble polymer

In this study, a water-soluble polymer, polyvinylpyrrolidinone (PVP) having chelating functionalities was used for the preconcentration and separation of traces of Pb, Cu, Ve and Mn prior to their determination by graphite furnace atomic absorption spectrometry. For this purpose, the sample and the PVP solutions were mixed and the metal bound polymer was precipitated by adding the mixture onto acetone. The precipitate was separated by decantation and dissolved with water. By increasing the ratio of the volumes of sample to water used in dissolving the precipitate, the analyte elements were concentrated as needed. The concentration of trace elements was determined using graphite furnace atomic absorption spectrometry. The analyte elements in matrix free aqueous solutions were quantitatively recovered. The validity of the proposed method was checked with a standard reference material (NIST SRM 1577b bovine liver) and spiked fruit juice, sea water and mineral water samples. The analytical results were found to be in good agreement with certified and added values. Detection limits (3δ) were 1.7, 3.6 and 4.1 μg l⁻¹ for Pb, Cu and Mn, respectively, using 10 μl of sample volume. The method is novel and can be characterized by rapidity, simplicity, quantitative recovery and high reproducibility.     

Improved separation of cadmium from indium,zinc, gallium and other elements by anion-exchange chromatography in hydrobromic nitric acid mixtures

The separation of cadmium from indium, zinc and many other elements is considerably improved by eluting these elements with 0.1 M hydrobromic–0.5 M nitric acid solution from a column of AG1-X8 resin. Cadmium is retained very strongly and can be eluted with 2 M nitric acid or 1 M ammonia–0.2 M ammonium nitrate solution. Separations are sharp and quantitative and from microgram amounts up to 2 g of indium and zinc are separated from amounts of cadmium ranging from micrograms up to 100 mg on a 2-g (4.6 ml) resin column. Ga(II), Fe(III). Mn(II), Co(II), U(VI) and Ni(II) can be separated quantitatively from cadmium in the same way. The behaviour of numerous elements is discussed, with special attention to lead, and relevant elution curves and results from the analysis of synthetic mixtures are presented.     

Chelating resin-impregnated paper chromatography, applications to trace element collection of ferrous and ferric ions, and determination by differential pulse anodic stripping voltammetry

An ion-exchange approach to the preparation of chelating resin is demonstrated whereby a typical sulfonated chelating agent, 7-iodo-8-hydroxy quinoline-5-sulfonic acid, is immobilized as counterions on a piperazinium polyelectrolyte matrix. The resulting chelate forming resin has been used to effect the selective separation of ferrous as well as ferric ion from a known mixture containing other trace elements without any complication of the leaching of either chelating ligand or resin from the stationary support. The chelating resin-impregnated paper chromatographic technique followed with differential pulse anodic stripping analysis is described for the preconcentration, separation, and recovery of divalent and trivalent ions of iron from the various heavy metals in aqueous phases. The combination of chelation and paper chromatography involves a differential migration procedure which provides a technique for the separation of analyte ions quantitatively without any interference from the complex matrices.     

Development of column-pretreatment chelating resins for matrix elimination/multi-element determination by inductively coupled plasma-mass spectrometry

Chelating resins, two kinds of iminodiacetate derivatives (IDA) of cross-linked chitosan (CCS) were synthesized and investigated for adsorption capacity, matrix elimination and collection/concentration of analytes by a column pretreatment in a multi-element ICP-MS determination method. The adsorption behavior of 54 elements at the 10 ng ml(-1) level on chitosan derivatives in a packed mini-column was systematically examined. Almost 30 kinds of metal ions were recovered quantitatively at pH 5 with CCS-HP/IDA (cross-linked chitosan possessing N-2-hydroxypropyl iminodiacetic acid groups) column. Compared with available chitosan-iminodiacetate resin, CHITOPEARL CI-03, the recovery of the metal ions such as Cu, Pb and La is satisfactory with CCS-IDA (cross-linked chitosan possessing N,N-iminodiacetic acid groups) and CCS-HP/IDA using 2 M nitric acid as an eluent, which may be attributed to the difference of cross-linking and macroporous structure. Compared with Chelex-100, the adsorption efficiency is in the order: Chelex-100 > CCS-IDA > CCS-HP/IDA, especially in the chelating ability for alkaline earth metals. The resin with a longer spacer (CCS-HP/IDA) showed higher adsorption selectivity between heavy metal ions and alkaline earth metals at pH < 7. The separation efficiency of the major matrix cations in seawater (Na. K, Mg, Ca) has also been investigated, and matrix interference was negligible even in a seawater sample at pH 5 with CCS-HP/IDA. The recoveries of Mn at pH 5 with CCS-HP/IDA or Chelex-100 were almost 100%. However, those of Mg with each resin were 4 or 98%, respectively. The adsorption capacities of synthesized CCS-HP/IDA for Cu(II), Pb(II) and La(III) were 0.90, 0.65 and 0.34 mmol g(-1), respectively. Therefore, the chelating chitosan resins developed are applicable to the pretreatment of trace amounts of elements in various kinds of water samples.     

Synthesis and Efficiency of an Epoxy-Urea Chelating Resin for Preconcentrating and Separating Trace Bi,In, Sn,Zr, V And Ti From Solution Samples

Abstract

A new epoxy-urea chelating resin was synthesized from epoxy resin and used for the preconcentration and separation of trace Bi(III), In(III), Sn(IV), Zr(IV), V(V) and Ti(IV) ions from solution samples. The analyzed ions can be enriched at pH 5 at a flow rate of 1–4 ml/min, and can be also desorbed with 10 mL of 2 M HCl +0.1g NH₄F solution from the resin column, with recoveries over 97%. The chelating resin reused 6 times can still adsorb quantitatively the Bi, In, Sn, Zr, V and Ti ions, and eighty to thousand-fold excesses of Ca(II), Mg(II), Cu(II), Zn(II), Al(III), Sb(III), Ni(II), Mn(II) and Fe(III) cause little interference with the enrichment and determination of these ions. The RSDs of the proposed method for the determination of 500–50 ng/ml Bi, In and Sn, 50–5.0 ng/ml Zr, V and Ti were in the range of 0.4 ～ 4.0%, the enrichment factor of the resin for the ions is in the range of 10–100. The recoveries of added standard in waste water are between 96% and 100%, and the concentration of each ion in alloy steel sample determined by the method is in good agreement with the reference value analyzed by a steel plant with average error <2.8%.     

Synthesis of polyacrylaminoimidazole chelating fiber and properties of concentration and separation of trace Au, Hg and Pd from samples

A novel polyacrylaminoimidazole chelating fiber is synthesized simply and rapidly from nitrilon (an acrylonitrile-based synthetic fiber) and used for the preconcentration and separation of trace Au(III), Hg(II) and Pd(IV) ions from solution samples. The analyzed ions can be quantitatively concentrated by the fiber up to a flow rate of 15.0 mlmin(-1) at pH 3 and can also be desorbed with 15 ml of 4 M HCl+3% thiourea from the fiber column, with recoveries of 96.5-100%. The chelating fiber is reused ten times; the recoveries of these ions are still over 92%, and 100-1000 times of excess of Fe(III), Al(III), Ca(II), Mg(II), Ni(II), Mn(II), Cu(II), Zn(II) and Cd(II) causes no interference in the determination of these ions by inductively coupled plasma atomic emission spectrometry. The capacities of the fiber for the analytes are in the range of 1.56-2.92 mmolg(-1). The results show that the relative standard deviations for the determination of 50.0 ngml(-1) each of Au(III), Hg(IV) and Pd(IV) are in the range of 0.7-2.1%. The recoveries of a standard added in real solution samples are between 97 and 99%, and the concentration of each ion in powder sample detected by the method is in good agreement with the certified value.     

Quantitative separation of beryllium from magnesium,calcium, aluminium,iron and other elements by cation-exchange chromatography in nitric acid-methanol

Beryllium is separated from Mg, Ca, Mn(II), Fe(III), Al, Co(II). Zn. U(VI), La and Gd by elution with 2.0 M nitric acid in 70 % methanol from a column of AG50W-X8 sulphonated polystyrene cation exchanger, while the other elements are retained quantitatively. Sr, Ba, Sc, Y, the other lanthanides, Zr, Hf, Th, Ga, In, Cd and Ni(II) should also be separated according to their distribution coefficients or elution behaviour. Separations are sharp and recoveries quantitative from millimolar amounts down to 10 μg of beryllium. The separation of Ti(IV) and Cu(II) from beryllium is not satisfactory and requires rather large columns. Bi(III), Pb(II), Hg(II) and the alkali metals are eluted together with beryllium, but can be separated by other methods. Typical elution curves and results for the quantitative separation of binary synthetic mixtures are presented.     

Preconcentration and separation of copper(II), cadmium(II) and chromium(III) in a syringe filled with 3-aminopropyltriethoxysilane supported on silica gel

In this study, a syringe was filled with silica gel loaded with 3-aminopropyltriethoxysilane, for the separation and preconcentration of copper, cadmium and chromium prior to their determination by graphite furnace atomic absorption spectrometry (GFAAS) in seawater. For this purpose, a syringe was filled with 0.5 g of modified silica gel and the sample solution was drawn into the syringe and ejected back again. The analyte elements were quantitatively retained at pH 5. Then, the elements sorbed by the silica gel were eluted with 2.0 M of HCl and determined by GFAAS. At optimum conditions, the recovery of Cu, Cd and Cr were 96-98%. Detection limits (3delta) were 6.6, 7.5 and 6.0 micro g L(-1) for Cu, Cd and Cr, respectively. The elements could be concentrated by drawing and discharging several portions of sample successively but eluting only once. Cu, Cd and Cr added to a seawater sample were quantitatively recovered (>95%) in the range of the 95% confidence level. The method proposed in this paper was compared with a column technique. Optimum experimental conditions, reproducibility, precision and recoveries of both techniques are the same, but the syringe technique is much faster, easier and more practical than the column technique. It is a portable system and allows one to make the sorption process in the source of sample. In addition, the risk of contamination is less than in the column technique.     

Use of 2-(tert-butoxy)-N-(3-carbamothioylphenyl)acetamide and graphene oxide for separation and preconcentration of Fe(Ⅲ),Ni(Ⅱ),Cu(Ⅱ) and Zn(Ⅱ) ions in different samples

A simple and selective method using a column packed with graphene oxide(GO) as a solid phase extractant has been developed for the multi-element preconcentration of Fe(Ⅲ),Ni(Ⅱ),Cu(Ⅱ) and Zn(Ⅱ)ions prior to flame atomic absorption spectrometric determinations.The method is based on the sorption of mentioned ions on synthesized GO using 2-(tert-butoxy)-N-(3-carbamothioylphenyl)acetamide as a chelating agent.Several parameters on the extraction and complex formation were optimized.Under the optimized conditions(pH 6,flow rate 9 mL/min),metal ions were retained on the column,then quantitatively eluted by HNO3solution(5 mL,3.0 mol/L).The preconcentration factor was calculated as250.The detection limits for the analyte ions of interest were found in the range of 0.11 ng/mL(Ni2+) to0.63 ng/mL(Cu2+).The column packed with GO was adequate for metal ions separation in matrixes containing alkali,alkaline earth,transition and heavy metal ions.     

Determination of iron and copper in seawater at pH 1.7 with a new commercially available chelating resin, NTA Superflow

The use of a commercially available chelating resin with NTA-type functional groups for concentration of trace metals from seawater is described. Trace metal recoveries from this NTA Superflow chelating resin are pH dependent. At a pH of ≤2 only iron(III) and copper are quantitatively recovered from the resin. Iron(II) cannot be quantitatively recovered from this resin below a pH of 5. However, oxidation of acidified seawater samples (pH 1.7) with H₂O₂ prior to loading onto the resin has been demonstrated to allow quantitative recovery of total dissolved iron. Deferrioxamine and Rhodoturlic Acid, two commercially available siderophores were used to investigate the effect of strong Fe(III)-binding organic ligands on the ability to retain iron at different pH values. Acidification of seawater samples to pH 1.7 dissociates the iron complexed to these organic ligands, thereby allowing total dissolved iron and copper to be determined. Acidified samples from Monterey Bay were analyzed by a flow injection method coupled to ICP-SFMS detection using the NTA Superflow resin in the pre-concentration step. Results from this study show that when seawater samples are stored acidified (pH 1.7) over time, a portion of iron(III) is reduced to iron(II), thus necessitating the use of H₂O₂ to reoxidize the Fe(II) to Fe(III) prior to analysis. Total dissolved concentrations of iron and copper can be directly obtained on seawater samples at pH 1.7 with this method, eliminating the need to buffer the sample to a higher pH prior to column loading. This resin has the potential to be used in shipboard or in situ flow injection methods.     

Azocalix[4]pyrrole Amberlite XAD-2: New polymeric chelating resins for the extraction, preconcentration and sequential separation of Cu(II), Zn(II) and Cd(II) in natural water samples

Two novel azocalix[4]pyrrole Amberlite XAD-2 polymeric chelating resins were synthesized by covalently linking diazotized Amberlite XAD-2 with calix[4]pyrrole macrocycles. The chelating resins were used for extraction, preconcentration and sequential separation of metal ions such as Cu(II), Zn(II) and Cd(II) by column chromatography prior to their determination by UV/vis spectrophotometry or flame atomic absorption spectrophotometry (FAAS) or inductively coupled plasma atomic emission spectroscopy (ICP-AES). Various parameters such as effect of pH on absorption, concentration of eluting agents, flow rate, total sorption capacity, exchange kinetics, preconcentration factor, distribution coefficient, breakthrough capacity and resin stability, were optimized for effective separation and preconcentration. The resin showed good ability for the separation of metal ions from binary and ternary mixture on the basis of pH of absorption and concentration of eluting agents. The newly synthesized resins showed good potential for trace enrichment of Cu(II), Zn(II) and Cd(II) metal ions, especially for Cu(II), as compared to the earlier reported resins. The synthesized resins were recycled at least 8-10 times without much affecting column sorption capacity. The presented method was successfully applied for determination of Cu(II), Zn(II) and Cd(II) in natural and ground water samples.     

Synthesis of Quinaldinic Acid Amide Derivative of Styrene-Divinylbenzene Copolymer and its Application in Preconcentration of Mercury (II)

Abstract

A new chelating resin has been synthesized by introducing a quinaldinic acid amide group into styrenedivinyl benzene (8%) copolymer beads. The resin is stable in fairly strong acids or alkali and has been characterized by elemental analysis for nitrogen and from i.r. spectra. The water regain value is 0.37g/g. The sorption patterns of Na(I), K(I), Ca(II), Mg(II), Pb(II), Cu(II), Ni(II), Zn(II), Cd(II), Hg(II) and Fe(III) on the chelating resin have been studied as a function of pH. The resin selectively sorbs Hg(II) ever a wide pH-range of 2.5–7.6 with high efficiency. The maximum exchange capacity for Hg(II) is 1.98 mmols g^?1 at pH 5.5. Over 99% of Hg(II) sorbed has been recovered by using 10% thiourea in 1M HClO₄ both by batch and column operations. The has been utilized in the preconcentration and recovery of Hg(II) from industrial and laboratory waste water.     

Sorption and preconcentration of copper and cadmium on silica gel modified with 3-aminopropyltriethoxysilane

3-Aminopropyltriethoxysilane, (C₂H₅O)₃ Si(CH₂)₃NH₂, loaded on silica gel was used as a pre-concentration sorbent for copper and cadmium prior to their determination by flame atomic absorption spectrometry (FAAS). Both batch and column methods were used for the separation of the above metals. The analytes are quantitatively retained on the proposed adsorbent at pH 6.5. The complexation capacity of the collector is 0.032 mmol Cu/g silica. In the batch method, the effects of shaking time and the ratio of metal/silica on the retention by the asorbent were investigated. Columns filled with the collector provided quantitative recovery of the above metals from standardized samples as well as from sodium chloride solutions.     

Solid-phase extraction and preconcentration of trace Pb(II) from water samples with folic acid modified silica gel

A chelating matrix prepared by immobilising folic acid on silica gel-bound amine phase was used as a new solid-phase extractant. This sorbent has been developed only for preconcentration of trace Pb(II) prior to determination by inductively coupled plasma atomic emission spectrometry (ICP-AES). Experimental conditions were investigated by batch and column procedures. The optimum pH value for the separation of Pb(II) on the new sorbent was 4.0. The adsorbed Pb(II) was quantitatively eluted by 2.0?cm³ of 0.5?mol?dm^?3 of HCl. Common coexisting ions did not interfere with the separation and determination of Pb(II). The maximum static adsorption capacity of the sorbent under optimum conditions was found to be 69.23?mg?g^?1 for Pb(II). The detection limit of the method defined by International Union of Pure and Applied Chemistry was 0.28?ng?cm^?3. The relative standard deviation (RSD) of the method was lower than 2.0% (n?=?8). The developed method has been validated by analysing certified reference materials and successfully applied to the determination of Pb(II) in water samples with satisfactory results.